Canon PowerShot S100 Manuel utilisateur

Guide de mise en route

Getting Started

ENGLISH

FRANÇAIS

CEL-SS2RA2M0

Getting Started

ENGLISH

• Make sure you read this guide, including the “Safety

Precautions” section, before using the camera.

• Reading this guide will help you learn to use the camera

properly.

• Store this guide safely so that you can use it in the future.

Please refer to the complete user guide included

on the DIGITAL CAMERA Manuals Disk for more

detailed information.

2

Check if the following items are included in your camera package.

If anything is missing, contact the retailer where you purchased the camera.

Checking the Package Contents

Camera Battery Pack NB-5L

(with Terminal Cover)

Battery Charger

CB-2LX/CB-2LXE

Interface Cable

IFC-400PCU

Wrist Strap

WS-DC11

Using the Manuals

Also refer to the manuals on the DIGITAL CAMERA Manuals Disk.

• Camera User Guide

Once you have mastered the basics, use the

camera’s many features to shoot more challenging

photos.

• Software Guide

Read when you want to use the included software.

• A memory card is not included (p. 11).

• Adobe Reader is required to view the PDF manuals. Microsoft Word/

Word Viewer can be installed to view the Word manuals (required only for

manuals for the Middle East).

Warranty System

Booklet

Getting Started

(This Guide)

DIGITAL CAMERA

Solution Disk

3

• Take some initial test shots and play them back to make sure the images

were recorded correctly. Please note that Canon Inc., its subsidiaries and

affiliates, and its distributors are not liable for any consequential damages

arising from any malfunction of a camera or accessory, including memory

cards, that results in the failure of an image to be recorded or to be

recorded in a way that is machine readable.

• The images recorded with this camera are intended for personal use.

Do not record images that infringe upon copyright laws without the prior

permission of the copyright holder. Please be advised that in certain cases

the copying of images from performances, exhibitions, or commercial

properties by means of a camera or other device may contravene copyright

or other legal rights even if the image was shot for personal use.

• For information on your camera’s warranty, please refer to the Canon

Warranty System Booklet supplied with your camera.

For Canon Customer Support contacts, please see the Warranty System

Booklet.

• The LCD monitor is produced with extremely high-precision manufacturing

techniques. More than 99.99% of the pixels operate to specification, but

occasionally non-performing pixels may appear as bright or dark dots. This

is not a malfunction and has no effect on the recorded image.

• The LCD monitor may be covered with a thin plastic film for protection

against scratches during shipment. If covered, remove the film before

using the camera.

• Please take care when operating the camera for an extended period as the

camera body may become warm. This is not a malfunction.

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

CANON EUROPA N.V.

Bovenkerkerweg 59-61, 1185 XB Amstelveen, The Netherlands

Read This First

4

• Icons are used in the text to represent the camera buttons and dials.

• Language that displays on the screen appears inside [ ] (square brackets).

• The directional buttons, control dial, FUNC./SET button and control ring

are represented by the following icons.

• : Things you should be careful about

• : Troubleshooting tips

• : Hints for getting more out of your camera

• : Supplemental information

• (p. xx): Reference pages (“xx” stands for a page number)

• This guide assumes all functions are at their default settings.

• The various types of memory cards that can be used in this camera are

collectively referred to as memory cards in this guide.

Conventions Used in This Guide

Right Button

FUNC./SET Button

Up Button

Left Button

Down Button

Control Dial

y Control Ring

5

• Before using the product, please ensure that you read the safety precautions described

below. Always ensure that the product is used correctly.

• The safety precautions noted on the following pages are intended to prevent injuries to

yourself and other persons, or damage to the equipment.

• Be sure to also check the guides included with any separately sold accessories you

use.

Safety Precautions

Warning

Denotes the possibility of serious injury or death.

• Do not trigger the flash in close proximity to people’s eyes.

Exposure to the intense light produced by the flash could damage eyesight. In particular,

remain at least 1 meter (39 inches) away from infants when using the flash.

• Store this equipment out of the reach of children and infants.

Strap: Putting the strap around a child’s neck could result in asphyxiation.

• Use only recommended power sources.

• Do not attempt to disassemble, alter or apply heat to the product.

• Avoid dropping or subjecting the product to severe impacts.

• To avoid the risk of injury, do not touch the interior of the product if it has been

dropped or otherwise damaged.

• Stop using the product immediately if it emits smoke, a strange smell, or

otherwise behaves abnormally.

• Do not use organic solvents such as alcohol, benzine, or thinner to clean the

product.

• Do not let the product come into contact with water (e.g. sea water) or other

liquids.

• Do not allow liquids or foreign objects to enter the camera.

This could result in electrical shock or fire.

If liquids or foreign objects come into contact with the camera interior, immediately turn

the camera off and remove the battery.

If the battery charger becomes wet, unplug it from the outlet and consult your camera

distributor or a Canon Customer Support Help Desk.

• Use only the recommended battery.

• Do not place the battery near or in direct flame.

• Unplug the power cord periodically, and using a dry cloth, wipe away any dust

and dirt that has collected on the plug, the exterior of the power outlet, and the

surrounding area.

• Do not handle the power cord with wet hands.

• Do not use the equipment in a manner that exceeds the rated capacity of the

electrical outlet or wiring accessories. Do not use if the power cord or plug are

damaged, or not fully plugged into the outlet.

• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals

or plug.

Safety Precautions

6

The battery may explode or leak, resulting in electrical shock or fire. This could cause

injury and damage the surroundings. In the event that a battery leaks and the battery

electrolyte contacts eyes, mouth, skin or clothing, immediately flush with water.

• Turn the camera off in places where camera use is prohibited.

The electromagnetic waves emitted by the camera may interfere with the operation of

electronic instruments and other devices. Exercise adequate caution when using the

camera in places where use of electronic devices is restricted, such as inside airplanes

and medical facilities.

• Do not play the supplied CD-ROM(s) in any CD player that does not support data

CD-ROMs.

It is possible to suffer hearing loss from listening with headphones to the loud sounds of

a CD-ROM played on an audio CD player (music player). Additionally, this could damage

the speakers.

Caution

Denotes the possibility of injury.

• When holding the camera by the strap, be careful not to bang it, subject it to

strong impacts or shocks, or let it get caught on other objects.

• Be careful not to bump or push strongly on the lens.

This could lead to injury or damage the camera.

• Be careful not to subject the screen to strong impacts.

If the screen cracks, injury may result from the broken fragments.

• When using the flash, be careful not to cover it with your fingers or clothing.

This could result in burns or damage to the flash.

• Avoid using, placing or storing the product in the following places:

- Places subject to strong sunlight

- Places subject to temperatures above 40 °C (104 °F)

- Humid or dusty areas

These could cause leakage, overheating or an explosion of the battery, resulting in

electrical shock, fire, burns or other injuries.

High temperatures may cause deformation of the camera or battery charger casing.

• The slideshow transition effects may cause discomfort when viewed for

prolonged periods.

• Take care not to pinch your finger when the flash lowers.

This could result in injury.

Safety Precautions

7

Caution

Denotes the possibility of damage to the equipment.

• Do not aim the camera at bright light sources (such as the sun on a clear day).

Doing so may damage the image sensor.

• When using the camera on a beach or at a windy location, be careful not to allow

dust or sand to enter the camera.

• Do not push down on the flash, or pry it open.

This may cause the product to malfunction.

• In regular use, small amounts of smoke may be emitted from the flash.

This is due to the high intensity of the flash burning dust and foreign materials stuck to the

front of the unit. Please use a cotton swab to remove dirt, dust or other foreign matter from

the flash to prevent heat build-up and damage to the unit.

• Remove and store the battery when you are not using the camera.

If the battery is left inside the camera, damage caused by leakage may occur.

• Before you discard the battery, cover the terminals with tape or other insulators.

Contacting other metal materials may lead to fire or explosions.

• Unplug the battery charger from the power outlet after charging is complete, or

when you are not using it.

• Do not place anything, such as cloth on top of the battery charger while it is

charging.

Leaving the unit plugged in for a long period of time may cause it to overheat and distort,

resulting in fire.

• Do not place the battery near pets.

Pets biting the battery could cause leakage, overheating or explosion, resulting in fire or

damage.

• Do not sit down with the camera in your pocket.

Doing so may cause malfunctions or damage the screen.

• When putting the camera in your bag, ensure that hard objects do not come into

contact with the screen.

• Do not attach any hard objects to the camera.

Doing so may cause malfunctions or damage the screen.

8

Checking the Package Contents ........................................................................... 2

Read This First ...................................................................................................... 3

Conventions Used in This Guide ........................................................................... 4

Safety Precautions................................................................................................. 5

Attaching the Strap/Holding the Camera ............................................................... 8

Charging the Battery.............................................................................................. 9

Compatible Memory Cards (Sold Separately) ..................................................... 11

Inserting the Battery and Memory Card............................................................... 12

Setting the Date and Time................................................................................... 14

Setting the Display Language.............................................................................. 17

Formatting Memory Cards................................................................................... 18

Pressing the Shutter Button................................................................................. 19

Taking Pictures (Smart Auto)............................................................................... 20

Viewing Images ................................................................................................... 23

Erasing Images.................................................................................................... 24

Shooting Movies .................................................................................................. 25

Viewing Movies.................................................................................................... 27

Transferring Images to a Computer for Viewing.................................................. 28

• Attach the included strap and wrap it around your wrist to avoid dropping

the camera during use. You can also attach the strap to the left side of the

camera.

• Keep your arms tight against your body while holding the camera firmly by

the sides when shooting. Be sure that your fingers do not block the flash

while it is raised.

Table of Contents

Attaching the Strap/Holding the Camera

Strap

9

Use the included charger to charge the battery. Be sure to charge the battery

as it is not charged at the time of purchase.

Remove the cover.

Insert the battery.

z Align the S marks on the battery and

charger, then insert the battery by sliding it

in ( ) and down ( ).

Charge the battery.

z For CB-2LX: Flip out the plug ( ) and

plug the charger into a power outlet ( ).

z For CB-2LXE: Plug the power cord into

the charger, then plug the other end into a

power outlet.

X The charge lamp lights orange and

charging starts.

X The charge lamp will light green when

charging has finished. Charging takes

approx. 2 hours and 5 minutes.

Remove the battery.

z Unplug the battery charger from the power

outlet, then remove the battery by sliding it

in ( ) and up ( ).

Charging the Battery

CB-2LX

CB-2LXE

To protect the battery and prolong its life, do not charge it for longer than

24 hours continuously.

Charging the Battery

10

Number of Possible Shots/Shooting and Playback Times

*1 The number of shots that can be taken is based on the Camera & Imaging Products

Association (CIPA) measurement standard.

*2 Times are based on default settings, starting and stopping shooting, turning the camera on

and off, and operations such as using the zoom.

*3 Times are based on repeatedly shooting until the maximum clip length is reached or recording

stops automatically.

• Under some shooting conditions, the number of possible shots and shooting time may

be less than mentioned above.

Battery Charge Indicator

An icon or message will appear on the screen indicating the battery’s charge

state.

Number of Shots*

1

Approx. 200

Movie Shooting Time

*2

Approx. 40 min.

Continuous Shooting

*3

Approx. 1 hr. 10 min.

Playback Time Approx. 4 hours

Display Summary

Sufficient charge.

Slightly depleted, but sufficient.

(Blinking red) Nearly depleted. Charge the battery.

“Change the battery pack.” Depleted. Charge the battery.

What if...

• What if the battery develops a bulge?

This is a normal characteristic of the battery and does not indicate a problem.

However, if the battery bulges to the point where it will no longer fit into the

camera, please contact a Canon Customer Support Help Desk.

• What if the battery is quickly depleted even after charging?

The battery has reached the end of its life span. Purchase a new battery.

Compatible Memory Cards (Sold Separately)

11

The cards below can be used without restrictions on their capacities.

• SD memory cards*

• SDHC memory cards*

• SDXC memory cards*

• Eye-Fi cards

* This memory card complies with SD standards. Some cards may not operate properly

depending on the brand of card used.

This product is not guaranteed to support Eye-Fi card functions (including

wireless transfer). In case of an issue with an Eye-Fi card, please check with

the card manufacturer.

Also note that an approval is required to use Eye-Fi cards in many countries

or regions. Without approval, use of the card is not permitted. If it is unclear

whether the card has been approved for use in the area, please check with

the card manufacturer.

Using the battery and charger effectively

• Charge the battery on the day, or the day before, it will be

used.

Charged batteries continue to discharge naturally even if

they are not used.

Attach the cover to a charged battery so that the S mark is

visible.

• How to store the battery for long periods:

Deplete and remove the battery from the camera. Attach the terminal cover and

store the battery. Storing a battery for long periods of time (about a year) without

depleting it may shorten its life span or affect its performance.

• The battery charger can also be used when abroad.

The charger can be used in regions that have 100 – 240 V (50/60 Hz) AC power.

If the plug does not fit the outlet, use a commercially available plug adapter. Do

not use electrical transformers for foreign travel as they will cause damage.

Compatible Memory Cards (Sold Separately)

Depending on your computer’s OS version, SDXC memory cards may not

be recognized even when using a commercially available card reader.

Check to make sure that your OS supports SDXC memory cards

beforehand.

About Eye-Fi Cards

12

Insert the included battery and a memory card (sold separately).

Check the card’s write-protect tab.

z If the memory card has a write-protect tab,

you will not be able to record images if the

tab is in the locked position. Slide the tab

up until you hear a click.

Open the cover.

z Slide the cover ( ) and open it ( ).

Insert the battery.

z Insert the battery as shown until it locks

into place with a click.

z Be sure to insert the battery in the correct

direction or it will not properly lock into

place.

Insert the memory card.

z Insert the memory card as shown until it

locks into place with a click.

z Be sure the memory card is oriented

correctly. Inserting the memory card in the

wrong direction could damage the camera.

Close the cover.

z Close the cover ( ), and press downward

as you slide it until it clicks into place ( ).

Inserting the Battery and Memory Card

Terminals

Inserting the Battery and Memory Card

13

Remove the battery.

z Open the cover and press the battery lock

in the direction of the arrow.

X The battery will pop up.

Remove the memory card.

z Push the memory card in until you hear a

click, then slowly release it.

X The memory card will pop up.

Number of Shots per Memory Card

• Values are based on the default settings.

• The number of shots that can be taken will vary depending on camera settings, the

subject and the memory card used.

What if [Memory card locked] appears on the screen?

If the write-protect tab is in the locked position, [Memory card locked] will appear

on the screen and you will not be able to take or erase images.

Removing the Battery and Memory Card

Memory Card 4GB 16GB

Number of Shots Approx. 1231 Approx. 5042

Setting the Date and Time

14

The Date/Time settings screen will appear the first time the camera is turned

on. Since the dates and times recorded into your images are based on these

settings, be sure to set them.

Turn on the camera.

z Press the ON/OFF button.

X The Date/Time screen will appear.

Set the date and time.

z Press the qr buttons to choose an option.

z Press the op buttons or turn the 7 dial

to set a value.

z Once all settings are complete, press the

m button.

Can you check the number of shots that can be taken?

You can check the number of shots that can be

taken when the camera is in a Shooting mode

(p. 20).

Setting the Date and Time

15

Set the home time zone.

z Press the qr buttons or turn the 7 dial to

choose your home time zone.

Complete the setting.

z Press the m button to complete the

setting. After a confirmation screen

appears, the shooting screen will

reappear.

z Pressing the ON/OFF button will turn off

the camera.

You can change the current date and time settings.

Display the menu.

z Press the n button.

Reappearing Date/Time screen

Set the correct date and time. If you have not set the date and time and the home

time zone, the Date/Time screen will appear each time you turn on the camera.

Daylight saving time settings

If you choose in Step 2 on p. 14 and press the op buttons or turn the 7 dial

to choose , you will set the time to daylight saving (1 hour ahead).

Changing the Date and Time

Setting the Date and Time

16

Choose [Date/Time].

z Move the zoom lever to choose the 3 tab.

z Press the op buttons or turn the 7 dial

to choose [Date/Time], then press the m

button.

Change the date and time.

z Follow Step 2 on p. 14 to adjust the

settings.

z Press the n button to close the menu.

Date/Time battery

• The camera has a built-in date/time battery (backup battery) that allows the

date/time settings to be retained for about 3 weeks after the battery pack has

been removed.

• By inserting a charged battery or connecting an AC adapter kit (sold separately,

see Camera User Guide) the date/time battery can be charged in about 4 hours

even if the camera is not turned on.

• If the date/time battery is depleted, the Date/Time screen will appear when you

turn the camera on. Follow the steps on p. 14 to set the date and time.

You can also automatically update the date and time with the GPS function

(see Camera User Guide).

17

You can change the language that displays on the screen.

Enter Playback mode.

z Press the 1 button.

Display the settings screen.

z Press and hold the m button, then

immediately press the n button.

Set the display language.

z Press the opqr buttons or turn the 7

dial to choose a language, then press the

m button.

X Once the display language has been set,

the settings screen will close.

Setting the Display Language

What if the clock appears when the m button is pressed?

The clock will appear if too much time passes between pressing the m button

and the n button in Step 2. If the clock appears, press the m button to

remove the clock and repeat Step 2.

You can also change the display language by pressing the n button

to choose [Language ] in the 3 tab.

18

Before you use a new memory card or one that has been formatted in other

devices, you should format the card with this camera.

Formatting (initializing) a memory card erases all data on the memory card.

As you cannot retrieve the erased data, exercise adequate caution before

formatting the memory card.

Before formatting an Eye-Fi card (see Camera User Guide), be sure to install

the software contained on the card to a computer.

Display the menu.

z Press the n button.

Choose [Format].

z Move the zoom lever to choose the 3 tab.

z Press the op buttons or turn the

7

dial

to choose [Format], then press the

m

button.

Choose [OK].

z Press the qr buttons or turn the 7 dial to

choose [OK], then press the m button.

Format the memory card.

z Press the op buttons or turn the 7 dial

to choose [OK], then press the m button

to start formatting.

z When formatting ends, [Memory card

formatting complete] appears on the

screen. Press the m button.

Formatting Memory Cards

Pressing the Shutter Button

19

To take images that are in focus, be sure to first press the shutter button

lightly (halfway) to focus, then press fully to shoot.

Press halfway (Press lightly to focus).

z Press lightly until the camera beeps twice

and AF frames appear where the camera

focused.

Press fully (Press fully to shoot).

X

The camera plays the shutter sound and

takes the shot.

z Since the shot is being taken while the

shutter sound plays, be careful not to move

the camera.

Formatting or erasing data on a memory card merely changes the file

management information on the card and does not ensure its contents are

completely erased. Be careful when transferring or disposing of a memory

card. When disposing of a memory card, take precautions such as

physically destroying the card to prevent personal information leaks.

• The total capacity of the memory card displayed in the formatting screen

may be less than indicated on the memory card.

• Perform a low-level format (see Camera User Guide) of the memory card

when the camera does not operate properly, the recording/reading speed

of a memory card has dropped, when continuous shooting speed slows

down, or when movie recording stops suddenly.

Pressing the Shutter Button

Does the length of the shutter sound change?

• Since the time required to shoot differs depending on the scene you want to

take, the length of the shutter sound may change.

• If the camera or subject moves while the shutter sound is playing, the recorded

image may be blurry.

If you shoot without pressing the shutter button halfway, the image may not

be in focus.

La page charge ...

Canon PowerShot S100 Manuel utilisateur

Canon PowerShot S100 Manuel utilisateur

dans d''autres langues

Documents connexes