Continental Fireplaces CBL46NTE Manuel utilisateur

Marque: Continental Fireplaces

Modèle: CBL46NTE

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

CBL36NTE-1

FRENCH

PG. 23

W415-2760 / D / 04.20.21

CBL36-1 / CBL46

(CBL46 with optional stainless steel surround illustrated)

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

- Installation and service must be performed by a qualiﬁ ed installer, service agency, or the supplier.

WARNING

ENGLISH

For indoor use only

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

OWNER’S MANUAL

SAFETY INFORMATION

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.continentalﬁ replaces.com • [email protected]

W415-2760 / D / 04.20.21

safety information

• This appliance is hot when operated and can cause

severe burns if contacted.

• Any changes to this appliance or its control can be

dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance

with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off

and cooled before servicing.

• Do not install damaged, incomplete or substitute

components.

• Risk of cuts and abrasions. Wear protective gloves

and safety glasses during installation. Sheet metal

edges may be sharp.

• Children and adults should be alerted to the

hazards of high surface temperature and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children, and others may be

susceptible to accidental contact burns. A

physical barrier is recommended if there are at

risk individuals in the house. To restrict access to

an appliance or stove, install an adjustable safety

gate to keep toddlers, young children and other at

risk individuals out of the room and away from hot

surfaces.

• Clothing or other ﬂ ammable material should not be

placed on or near the appliance.

• Due to high temperatures, the appliance should be

located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety

measure to protect infants/toddlers from touching

hot surfaces.

• Even after the appliance is out, the glass and/or

screen will remain hot for an extended period of

time.

• Check with your local hearth specialty dealer

for safety screens and hearth guards to protect

children from hot surfaces. These screens and

guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for

servicing the appliance, must be replaced prior to

operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do

not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free

from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

WARNING

• Under no circumstances should this appliance be

modiﬁ ed.

• This appliance must not be connected to a chimney

ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service

technician to inspect the appliance and to replace

any part of the control system and any gas control

which has been under water.

• Do not operate the appliance with the glass door

removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed

service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they

must be kept closed while the appliance is

operating to prevent exhaust fumes containing

carbon monoxide, from entering into the home.

Temperatures of the exhaust escaping through

these openings can also cause the surrounding

combustible materials to overheat and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the unit

are to be installed on the appliance.

• Keep the packaging material out of reach of

children and dispose of the material in a safe

manner. As with all plastic bags, these are not toys

and should be kept away from children and infants.

• As with any combustion appliance, we recommend

having your appliance regularly inspected and

serviced as well as having a carbon monoxide

detector installed in the same area to defend you

and your family against carbon monoxide.

• Ensure clearances to combustibles are maintained

when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or

in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or

other electronic components.

• A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed

service person. The appliance should be inspected

before use and at least annually by a professional

service person. More frequent cleaning may be

required due to excessive lint from carpeting,

bedding material, etc. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean.

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2760 / D / 04.20.21

table of contents

1.0 getting to know your appliance 5

1.1 control access 6

1.2 rating plate information 6

2.0 operating your appliance 7

2.1 using your appliance 7

2.2 on/off components 7

2.3 operating and lighting instructions 8

2.4 pilot-on-demand 9

2.4.1 changing the batteries in the battery holder 10

2.4.2 turndown 10

3.0 clearances around fireplace 11

3.1 optional heat management system 12

3.2 clearances around appliance (TV and valuable objects) 13

4.0 maintenance 14

4.1 care of glass 14

4.2 care of plated parts 15

4.3 safety barrier removal 15

4.4 door trim removal 16

4.5 ﬁ rebox glass door removal 16

5.0 replacement parts 17

6.0 accessories 18

7.0 troubleshooting 19

8.0 warranty 20

9.0 service history 21

This owner’s manual is written for a complete series of ﬁ replaces that have a variety of different features and speci-

ﬁ cations. Before reading this manual, be sure you know which model of ﬁ replace that you have. This information

will have been ﬁ lled out by the installer on the following page and on the rating plate that is permanently attached

to the ﬁ replace (see “rating plate information” section).

This manual is for the:

• CBL36-1 and CBL46 models

If required, more detailed technical information is included in the ﬁ replace installation manual.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial, are denoted by a vertical line in the margin.

Visit the Continental website for the most current version of your appliance’s manual.

W415-2760 / D / 04.20.21

welcome

Dealer Information

Name of Dealer:

Dealer Location:

Dealer Phone:

Dealer E-mail:

Customer:

Customer Address:

Date of Installation:

Location of the appliance:

Installer:

Continental is proudly committed to your total home comfort. We are proud to say that our products continunously

surpass industry standards and our inspiration is you! More than anything, we want you to feel conﬁ dent in

choosing Continental for your home. Our products are designed to provide that conﬁ dence and ensure that every

Continental product is beyond compare.

Continental products are designed with superior components and materials assembled by trained craftsmen who

take great pride in their work.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance for your

safety. This barrier must be installed.

Your Continental ﬁ replace has been thoroughly inspected by a qualiﬁ ed technician before packaging to ensure that

you, the customer, receives the quality product that you expect from Continental.

Dealer : Fill in your dealer information (or business card) and the appliance installation information

below.

congratulations

Model:

Serial Number:

Dealer: Business card location

Natural Gas: CBL36NTE-1

CBL46NTE

Propane: CBL36PTE-1

CBL46PTE

W415-2760 / D / 04.20.21

getting to know your appliance

1.0 getting to know your appliance

Burner

Pilot

Safety barrier Glass door

Door trim Valve /

rating plate

/ lighting

instructions /

battery back

Some features and locations may vary depending on the model.

note:

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

The area above the ﬁ replace opening including the safety barrier, barrier frame and

the surface of the wall can get very hot during operation and should never be touched

until the appliance is off and completely cooled.

W415-2760 / D / 04.20.21

getting to know your appliance

Access to the control can be done by removing the safety barrier, door trim and control cover (see “maintenance”

section for instructions on how to remove these components).

1.1 control access

FLAME

ADJUSTMENT

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

1.2 rating plate information

The rating plate must remain with the appliance at all times. It must not be removed.

note:

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

Élévation

Alimentation

Alimentation Réduite

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING

Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT

N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33b

- 2008, ANSI Z21.88

- 2008 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTÉ

AU GAZ ET VENTILÉ

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALL

ATION IF INSTALLED IN ACCOR

DANCE WITH THE

CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONST

RUCTION AND SAFETY STANDARD, TITLE 24 CFR,

PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATION

S, SITES AND COMMUNITIES, ANSI / NFPA 501A.

FOYER DE CHAUFFAGE AU GAZ AVEC ÉVACUATION. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUD

IO. APPROPRIÉ POUR INSTALLATION DANS UNE

MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, E

N VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

NORME DE SECURITÉ ET DE C

ONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR,

SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME

RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET

LES COMMUNAUTÉS, ANSI/NFPA 501A.

NOT FOR USE WITH

SOLID FUEL. FOR USE

WITH GLASS DOORS

CERTIFIED WITH THIS

UNIT ONLY.

WARNING

DO NOT ADD ANY MATERIAL

TO THE APPLIANCE, WHICH WILL COME

IN CONTACT WITH THE FLAMES, OTHER

THAN THAT SUPPLIED BY THE

MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS:

TOP 0”

FLOOR 0”

RECESSED DEPTH ONE SIDED 23"

RECESSED DEPTH SEE THRU 13.5”

FRAMING (NOT INCLUDING

FACE MATERIAL)

SIDES 0”

VENT 2"

BACK 0”

MANTLE 15" *

TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS

SEE OWNERS MANUAL

UN COMBUSTIBLE SOLIDE NE

DOIT PAS ÊTRÉ UTILISÉ AVEC

CET APPAREIL. UTILISER AVEC

LES PORTES VITRÉES

HOMOLOGUÉES SEULEMENT

AVEC CETTE UNITÉ.

AVERTISSEMENT:

N'AJOUTEZ PAS A

CET APPAREIL AUCUN MATÉRIAU DEVANT

ENTRER EN CONTACT AVEC LES FLAMMES

AUTRE QUE CELUI QUI EST FOURNI AVEC

CET APPA

REIL PAR LE FABRICANT.

DÉGAGEMENTS

MINIMAUX DES

MATÉRIAUX COMBUSTIBLES:

DESSUS 0”

PROFONDEUR D'ENCASTRÉ 25"

PLANCHER 0”

ÉVENT 2"

CÔTES 0”

MANTEAU 15" *

ARRIÉRE 0”

MADE IN CANADA / FABRIQUÉ AU CANADA

WOLF STEEL LTD. BARRIE, ONTARIO, CANADA

ALTITUDE / ÉLÉVATION

INPUT / ALIMENTATION

REDUCED INPUT / ALIMENTATION RÉDUITE

ORIFICE / INJECTEUR

MANIFOLD PRESSURE /

PRESSION AU COLLECTEUR

MINIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MINIMALE

MAXIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MAXIMALE

0-4500FT (0-1370M)

30,000 BTU/H

3,000 BTU/H

#38

3.5" WATER COLUMN/D'UNE COLONNE D'EAU

4.5" WATER COLUMN/D'UNE COLONNE D'EAU

7.0" WATER COLUMN/D'UNE COLONNE D'EAU

0-4500FT (0-1370M)

30,000 BTU/H

23,000 BTU/H

#53

10" WATER COLUMN/D'UNE COLONNE D'EAU

11" WATER COLUMN/D'UNE COLONNE D'EAU

13" WATER COLUMN/ D'UNE COLONNE D'EAU

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE

NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

FOR VENTING SPECIFICS. PROPER REINSTALLATION AND

RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

INTAKE SYSTEM.

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE

D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL

D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION

PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET

RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU

SYSTÉME DE PRISE D'AIR.

CLASSIFICATION: 115V 0.82AMP, 60HZ

W385-2007

MODEL NATURAL GAS /

GAZ NATURAL

LHD50NT

MODEL PROPANE

LHD50PT

SERIAL NUMBER/NO. DE SÉRIE:

LV50

ELECTRICAL RATING: 115V 0.82AMP, 60HZ

REFERENCE #

W/N 16131

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION

HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE

SELON LE MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.

L'EXTENSION HORIZONTALE MAXIMALE: 2". RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS

PLUS GRANDES. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTA

RE.

SAMPLE

Appliances

eils à gaz décoratif à évacuationacuation

installed in accordance with the current nstalled in accordance with the current

ion and Safety Standard, Title 24 CFR, Part on and Safety Standard, Title 24 CFR, Part

d CommunitiesCommunities

ANSI / NFPA 501A. This appliance

, ANSI / NFPA 501A. This appliance

r WXXX-XXXX. Follow installation instructions.X-XXXX. Follo

stallation dans une maison mobile si son installation une maison m

, ou, aux Étatu, aux Éta

selo

s selon la norm

FR, Part 3280,

80,

tiliser la norme iser la norme

NFPA 501A, Fire Safety Criteria for Manufacture

NFPA 501A, Fire Safety Criteria for Manufactured

de tels règlements, selon les codes d’installation ANSI Z223.1 ou e tels règlements, selon les codes d’installation ANSI Z223.1 ou

USA)SA)

TEEL LTD.

WOLF STEEL LTD.

24 Napoleon Road, Barrie24 Napoleon Road, Barr

XXXXXXXX

Élévation

Ali

ionmentation

Alim

n R

édu

eAlimentation Réduite

P4P4

ifold

essu

Manifold Pressure:

0” w.c.

(

)(P)

inimum

Pressure:

m Supply Pressure:

1” w.c.

(

)11” w.c. (P)

aximum Su

Pressure:

Supply Pressure:

3”* w.c.

(

)13”* w

Pression au

ollecteur:

Pression au Collecteur:

0” d’une colonne d’eau (P)

10” d’une colonne d’eau

ess

’Alim

n Min.:

Pression d’Alimentation Min.:

1” d’une colonne d’eau

(

)11” d’une colonne d’eau (P

ress

d’Ali

mentat

ax.:

ession d’Alimentation Max.

13” * d’une colonne d’eau (P)3” * d’une colonne d’eau (P

** Pression d’alimentation maximale ne devait pas dépasser 1ssion d’alimentation maximale ne devait pas dépasser

and ﬁnishing

ing materials, ng materia

ppliance openingppliance opening

Dégagements minimaux des matériaux combustgagements minimaux des matériaux

Dessus, côtés et arrière: selon les espaceurs de dégacôtés et arrière: selon les espaceurs de

pour les matériaux d’ossature selon le manuel duatériaux d’ossature selon le manuel

pour les matéles ma

CôtéCô

Maximum horizontal extension: aximum horizontal extensio

”. See installation manual for See installation manual fo

greater extensions, minimum vent

reater extensions, minimum vent

lengths and maximum vent lengths.

engths and maximum vent lengths.

VENTED DECORATIVE GAS APENTED DECORATIVE GAS AP

HEAT, NOT INTT, NOT IN

APPLIANCIAN

APPAREIL À GAZ DAPP

UNE SOURCE

UTILIS

FOR UFOR U

XXX

Electrical ratin

: 115V, 60HZ. Less than 12 amperes.

Electrical rating: 115V, 60HZ. Less than 12 ampere

X.X%

XXXXXXXX

VALVE

W415-2760 / D / 04.20.21

operating your appliance

2.0 operating your appliance

To turn the appliance on:

When operating your appliance for the ﬁ rst time, there is a required burn-in process that cures materials used

to manufacture the ﬁ replace that may emit both vapors and an odor. These are normal when operating a new

appliance for the ﬁ rst time. Ensure adequate air circulation is provided during burn-in process,

2.1 using your appliance

A. Turn the on/off switch on.

B. After 3-5 seconds, the control will start a spark at the pilot, light the pilot and then the burner. The spark

period will last 60 seconds, or until the pilot has lit.

C. When used for the ﬁ rst time, if the burn-in process was not completed by the installer, run appliance

continuously for 4 hours (burn-in).

D. Turn the appliance off. Wait until appliance is completely cool before moving to the next step.

E. Remove the safety barrier and ﬁ rebox glass door. Clean ﬁ rebox glass door (see “maintenance” section).

Replace ﬁ rebox glass door and safety barrier.

For more detailed information, see your installation manual or contact your authorized dealer.

2.2 on/off components

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

| On/off switch | Battery holder | Battery holder (including switch) | Remote control

(Optional)

(Not supplied)

W415-2760 / D / 04.20.21

operating your appliance

WARNING

• Do not turn on if children or other at risk individuals are near the appliance.

• This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the

pilot by hand.

• Before operating, smell all around the appliance area for gas and next to the ﬂ oor because some gas is

heavier than air and will settle on the ﬂ oor.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and replace any part of the control system and any gas control which has been

underwater.

FOR YOUR SAFETY READ BEFORE LIGHTING

WHAT TO DO IF YOU SMELL GAS

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

A. Stop! Read the above safety information on this label.

B. Remove batteries from the transmitter and set thermostat to lowest setting, if

equipped.

C. Turn off all electrical power to the appliance.

D. Open the glass door, if equipped.

E. Turn the manual shut-off valve clockwise to the “OFF” position. (Shut-off valve is

located on the ﬂ ex connector).

F. Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the

ﬂ oor, STOP! Follow the instructions above in the “WHAT TO DO IF YOU

SMELL GAS” section. If you don’t smell gas; close the glass door and go to

the next step.

G. Turn the manual shut-off valve counter clockwise to the “ON” position.

H. Turn on all electrical power to the appliance and re-install the batteries into the

transmitter. Set thermostat to desired setting, if equipped.

I. Turn on the remote wall switch to the appliance.

J. If the appliance will not operate, follow instructions “TO TURN OFF GAS” and

call your service technician or gas supplier.

A. Set thermostat to lowest setting, if equipped.

B. Turn off the remote wall switch to the appliance.

C. Turn off all electric power to the appliance if service is to be performed.

D. Turn manual shutoff valve clockwise to the “OFF” positon. Do not force.

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

• If you do not follow these instructions exactly, a ﬁ re or explosion may result causing property damage, personal

injury, or loss of life.

• If applicable, always light the pilot whether for the ﬁ rst time or if the gas supply has run out with the glass door

opened or removed.

add gas knob

add gas valve

Ensure that a continuous gas ﬂ ow is at the burner before installing the door. When lit for the ﬁ rst time, the

appliance will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of

paints and lubricants used in the manufacturing process and will not occur again. After extended periods of

non-operation, such as, following a vacation or warm weather season, the appliance may emit a slight odor for a

few hours. This is caused by dust particules in the heat exchanger burning off. In both cases, open a window to

sufﬁ ciently ventilate the room.

This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the

pilot by hand.

note:

2.3 operating and lighting instructions

W415-2760 / D / 04.20.21

operating your appliance

This appliance is equipped with an “On Demand” intermittent pilot ignition system (IPI) which also includes a

continuous pilot ignition (CPI) mode with an integrated seven day timer. This system minimizes your appliance’s

carbon footprint as well as reducing its annual fuel consumption and operating costs.

In IPI mode, the pilot will ignite prior to the main burner, when the appliance is turned on using a switch, remote

or from a call for heat with the thermostat (if equipped). Once the appliance is turned off (or the call for heat is

satisﬁ ed), the main burner and pilot ﬂ ame will shut down.

The continuous (CPI) mode is intended to enhance the performance of the appliance during the startup phase in

colder climates and extreme weather by keeping the system warm when the main burner is not in use. However,

the timer feature provides the convenience that the appliance automatically switches off the pilot when the

appliance has not been used for seven days to save unnecessary fuel consumption.

When the CPI function is turned on, the pilot will remain on after the main burner

is turned off. A timer will then begin the countdown for approximately seven days

before shutting off the pilot if the appliance is not used. This countdown will reset

anytime the appliance main burner is used. Therefore, if the appliance is regularly

used day to day, the pilot will remain on. However, this system does not require

the user to remember to turn the pilot off as summer approaches and avoids

unnecessary fuel consumption while still readily turned back on when the cold

weather returns.

Your appliance may be equipped with an ACS or remote control device which

enables you to select IPI or CPI modes.

If your appliance is equipped with an ACS switch, it has the option to change

modes. If installed with the blue wire facing up, ﬂ ipping the switch UP turns on the

continuous pilot with timer and ﬂ ipping the switch DOWN turns on the intermittent

pilot ignition. If installed with the white wire facing up, the opposite is true.

If your appliance is equipped with a remote control device capable of selecting IPI / CPI modes, refer to remote

operating instructions.

In order to start your pilot, turning the main burner on with the switch, remote or thermostat and then turning it off

will reactivate the continuous pilot mode and reset the seven day timer.

For further information, refer to www.napoleon.com/pilotondemand.

ADD TITLE: PIL

T-

N-DEMAND

2.4 pilot-on-demand

W415-2760 / D / 04.20.21

operating your appliance

2.4.1 changing the batteries in the battery holder

• Ensure the gas and electrical power to the appliance is turned off.

• Appliance may be hot, do not service until the appliance has cooled.

WARNING

A. Turn off the gas and disconnect the electrical power supply from the appliance.

B. Remove the safety barrier, control cover and door trim to easily access the control compartment (see

“maintenance” section for instructions on how to remove these components).

C. Locate the battery housing located near the control board (see illustration below).

D. Open the battery housing by sliding the back piece upwards and off of the battery housing. Remove the

four “AA” alkaline batteries and install four new “AA” alkaline batteries into the battery housing. Ensure the

positive and negative ends correspond with those identiﬁ ed on the holder.

E. Place the battery housing back into the control compartment, ensure that the battery housing is placed in

a clean and easily accessible location.

F. Reinstall the safety barrier. The safety barrier must be installed at all times during the appliance operation.

G. Turn the gas and electrical power back on to begin operating the appliance.

In the event of a power failure, your appliance can be operated using the supplied battery back-up. If a power

failure occured, remove the batteries from the holder once the power has been restored.

note:

Control module

Battery housing

Red wire

Black wire

Manual adjustments to your ﬁ replace must only be made when the appliance is off and complete cool.

Allow safety barrier to cool before making adjustment.

The CBL36-1/CBL46 models are equipped with a manual gas control knob (located on the valve) that adjusts the

ﬂ ame height to suit your preference. To access the gas control knob, remove your safety barrier, control cover and

door trim (see “maintenance” section for instructions on how to remove these components).

Use only your hand to turn the gas control knob (never use tools). If the knob will not turn by hand, do not try to

repair it. Contact a qualiﬁ ed technician.

Flame adjustment

2.4.2 turndown

W415-2760 / D / 04.20.21

clearances around ﬁ replace

WARNING

• Your appliance, gas/electrical connections, venting and various key components are hidden behind the wall. It is

critical that no screws penetrate these components. Failure to follow instructions may cause improper operation,

damage, personal injury or ﬁ re. Always use a stud ﬁ nder and only screw into studs.

3.0 clearances around ﬁ replace

Without making adequate provisions to account for the heat, the temperatures above the ﬁ replace will be hot,

making it unsuitable for mounting a TV or other objects sensitive to heat without risk of damage.

Installing a mantel between this appliance and electronics or other materials that may be sensitive to heat will

reduce the effect of direct heat on them.

The size and material of the mantel will affect the allowable clearance above your ﬁ replace. Incorrect placement

could become a ﬁ re hazard. Consult your installation manual and/or authorized dealer for more information before

mounting a mantel, a shelf or any other object above your appliance.

Your ﬁ replace, gas/electrical connections and vent are hidden directly behind the ﬁ nished wall. Great care should

be taken to avoid screwing or nailing into these components. Always use a stud ﬁ nder to determine stud location

and only screw into studs.

Do not screw into the area around the ﬁ replace opening as some of your appliance may be hidden behind the

ﬁ nished wall. Refer to your installation manual and/or contact your local dealer for more information.

Fireplaces

generate radiant

heat. Do not put

objects in front

of the appliance

(minimum

distance of 4 feet

[1.21m]).

The area above a ﬁ replace gets hot.

Combustible objects or materials must

never be placed in this area. For mini-

mum clearances, refer to installation

manual or your authorized dealer.

WARNING

W415-2760 / D / 04.20.21

clearances around ﬁ replace

3.1 optional heat management system

The Universal Heat Management system is an optional gravity vent kit that allows you to manage the heat

produced by the appliance at and around the ﬁ replace.

We recommend installing the Universal Heat Management system kit during the installation of the appliance

BEFORE the gas is installed.

For more information, contact your local authorized dealer.

Reduced mantel

clearances

Grill to expel

warm air into the

room

Reduced

temperatures

above fireplace

W415-2760 / D / 04.20.21

clearances around ﬁ replace

3.2 clearances around appliance (TV and valuable objects)

* TV applications were tested with the minimum enclosure dimensions and the maximum recess permissible.

This data is provided in good faith and is not a guarantee for every application and television. Care and

consideration should be taken when planning these installations to ensure the temperatures around the TV meet

all manufacturer’s recommended operating temperatures. Increasing the height of the mantel and/or TV above

the ﬁ replace opening, the protrusion of mantel and the volume of the enclosure all have the effect of reducing

the temperature above the ﬁ replace. It is always recommended to use the optional heat management kit

when considering mounting a television above the ﬁ replace.

6” min.

Appliance opening

2.5” min.*

2” min.

(3” max.

recommended)

6” min.

2.5” min.*

Enclosure

TV bracket

Flush installation with

mantel

Recessed installation with

protrusion

Appliance opening

2” min.

(3” max. recommended)

Appliance

opening

Enclosure

TV bracket

Flush installation without

mantel

Appliance

The volume of

air must be

added to the

enclosure to

accomodate

the recessed

area.

6” min.

Enclosure

TV bracket

Partially recessed installation with mantel

Appliance opening

Appliance

Enclosure

3” min.

See “minimum clearance to

mantle” section (installation

manual).

Mantle clearances reduced

from opening with the use of the

universal heat management

system.

12”

max.

2.5” min.*

2” min.

(3” max.

recommended)

6” min.

Appliance opening

2.5” min.*

2” min.

(3” max.

recommended)

Enclosure

TV bracket

Flush installation with mantel

Enclosure

Appliance

These applications are

only acceptable when the

Universal Heat Management

kit is installed.

WARNING

W415-2760 / D / 04.20.21

maintenance4.0 maintenance

WARNING

• Turn off the gas and electrical power before servicing the appliance.

• Appliance may be hot. Do not service until appliance has cooled.

For qualiﬁ ed technicians only:

• Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

• This appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed service

person.

• The ﬂ ow of combustion and ventilation air must not be obstructed.

DOS

• Clean your safety barrier regularly to prevent the

build up of excessive lint/dust from carpeting, pet

hair, etc. Vacuum using the brush attachment.

• Always use ammonia-free glass cleaners.

• Service your appliance annually and/or as

required. Service must be conducted by a qualiﬁ ed

technician.

• Keep your appliance area clear and free of

combustible materials, gasoline, or other ﬂ ammable

vapors and liquids.

• Check to see that the burner ignites completely

on all openings when turned on. A 5 to 10 second

total light-up period is satisfactory. Service as

required.

DON’TS

• Attempt to service the electrical or gas

components. Contact a qualiﬁ ed technician.

• Use excessive force.

• Use abrasive cleaners on glass.

• Paint the pilot assembly.

• Place objects too close to the ﬁ replace opening.

For any questions and/or concerns regarding your appliance, maintenance and service, please contact your

authorized dealer.

note:

Buff lightly with a clean dry soft cloth to remove accumulated dust or ﬁ ngerprints. Clean both sides of the glass

after the ﬁ rst 10 hours of operation with an ammonia-free glass cleaner.

Thereafter, clean as required. If the glass is not kept clean permanent discoloration and / or blemishes may

result. Contact you local authorized dealer / distributor for complete cleaning instructions.

Razor blades, steel wool, or other metallic objects must not be used on both surfaces of the glass. Doing so

can remove a thin layer of metal from the razor blades, steel wool, or other metallic objects that may then be

deposited onto the coating. This can result in a discoloured stain or scratch-like mark. More importantly, this can

scratch the glass surface, thereby reducing its strength.

Do not operate the appliance with broken glass, as leakage of ﬂ ue gases may result.

Contact your local authorized dealer / distributor for complete cleaning instructions.

If the glass should ever crack or break while the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not

operate the appliance until the glass has been replaced. Contact you local authorized dealer / distributor for

replacement parts. DO NOT SUBSTITUTE MATERIALS.

Vinegar-based glass cleaners have demonstrated an ability to provide a clean, streak free glass surface.

note:

Firebox Glass Door :

4.1 care of glass

WARNING

• Do not clean glass when hot! Do not use abrasive cleaners to clean glass.

Do not use ammonia-based cleaners.

W415-2760 / D / 04.20.21

maintenance

This appliance is factory equipped with tempered glass. Use only replacement parts as supplied by the appliance

manufacturer. DO NOT SUBSTITUTE MATERIALS.

Replacement glass/frame assembly shall be replaced as a complete unit as supplied by the appliance

manufacturer.

4.2 care of plated parts

If the appliance is equipped with plated parts, you must clean ﬁ ngerprints or other marks from the plated surfaces

before operating the appliance for the ﬁ rst time. Use an ammonia-free or vinegar-based cleaner and a towel

to clean. If not cleaned properly before operating for the ﬁ rst time, the marks can cause permanent blemishes

on the plating. After the plating is cured, the ﬁ ngerprints and oils will not affect the ﬁ nish and little maintenance

is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause

discolouration on plated parts.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can

be improved if the assembly is warmed (i.e. using a hair dryer or similar heat source).

note:

SAFETY BARRIER

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and must be installed.

Lift the safety barrier off the four shoulder screws and remove from the appliance. Reverse this step to install.

WARNING

• Glass may be hot. Do not touch glass until cooled.

• If equipped with door latches that are part of a safety system, they must be properly engaged. Do not

operate the appliance with latches disengaged.

• Facing and/or ﬁ nishing materials must not interfere with air ﬂ ow through air openings, louvre openings,

operation of louvres, or doors/access for service. Observe all clearances when applying combustible

materials.

• Before door is removed, turn the appliance off and wait until appliance is cool to the touch. Doors are heavy

and fragile so handle with care.

4.3 safety barrier removal

W415-2760 / D / 04.20.21

maintenance

To remove, slide the back edge of the door trim up and out of the glass and door frame.

To install, slide the back edge of the door trim down between the glass and door frame. Insert downwards.

4.4 door trim removal

These spring latches make up the spring

relief system for the appliance. Ensure

the door opens freely and closes sealed.

note:

When mounting the door, ensure there is

equal space on both left and right sides.

This allows for easy installation of the

front.

note:

CBL46 illustrated

Leave a hand on the glass door during entire door removal. The glass door is secured to the ﬁ rebox with four

(CBL36-1) or six (CBL46) spring latches. Pull the handles of the latches forward, then lift the latches out from the

door frame to release the door. Next, lift the door up until the bottom edge clears the bottom shoulder screws of

the appliance. Carefully grip the top and bottom of the door, lifting it off the appliance.

Reverse these steps to reinstall the door.

Ensure safety screen is installed correctly.

4.5 ﬁ rebox glass door removal

W415-2760 / D / 04.20.21

replacements

5.0 replacement parts

WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁ cally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

For service parts, see your Installation manual.

W415-2760 / D / 04.20.21

accessories

6.0 accessories

REF.

Description

Part Number

Stocked

CBL36-1 CBL46

Classic Side Trim (Black)

W715-1135 W715-1135

Premium Side Trim (Stainless Steel)

W715-1133 W715-1133

Classic Top/Bottom Trim (Black)

W715-1141 W715-1134

Premium Top/Bottom Trim (Stainless Steel)

W715-1140 W715-1132

Left Bracket

W080-1798 W080-1798

Right Bracket

W080-1797 W080-1797

Rear Porcelain Panel

W475-1060 W475-1374

Side Porcelain Panel

W475-1059 W475-1375

Shore Fire Kit

SFKS SFKM

Yes

Beach Fire Kit

BFKXS BFKM

Yes

Mineral Rock Kit

MRKXS MRKM

Yes

Blower (GZ600KT)

W062-0051 W062-0051

Variable Speed Switch

KB-35 KB-35

Yes

Thermodisc

W690-0002 W690-0002

Yes

Anti-Condensation Switch

ACS-SIT ACS-SIT

Yes

Items may not appear exactly as illustrated.

5453

551211

448

529

447

442 445441442441

446

443

444

W415-2760 / D / 04.20.21

troubleshooting

7.0 troubleshooting

symptom problem test solution

Flame is a blue,

Blockage in vent. - Remove blockage. In really cold conditions, ice buildup may

occur on the terminal and should be removed as required.

White / grey ﬁlm forms

on glass.

Sulphur from fuel is being

depos

ited on glass, logs, or

surfaces.

- Clean the glass with a recommended gas ﬁreplace glass

cleaner.

NOT CLEAN GLASS WHEN HOT.

If sulphur deposits are not cleaned off regularly, the glass may

become permanently marked.

Exhaust fumes smelled

in room, headaches.

Appliance may be leaking

exhaust fumes into the room.

- Check ﬁrebox glass door was properly reinstalled after cleaning

If not rectiﬁed, turn off appliance. Contact a qualiﬁed technician.

Pilot will not light. Makes

noise with no spark at

pilot burner.

No siginal from remote with no

pilot ignition.

- Reprogram receiver code.

- Replace battery holder (including switch), if applicable.

Pilot sparks but will

not light.

Gas supply. - Contact a qualiﬁed technician.

Out of propane gas. - Fill the tank.

Remote control (if equipped). - Follow reprogramming instructions for speciﬁc remote

installed with your appliance.

- Replace remote control.

Battery holder (including

switch) is in “off”

position; burner comes

on.

Battery holder (including wall

switch) mounted upside down.

- Reverse.

Battery holder (including switch)

and/or wire is grounding.

- Replace.

- Check for ground (short); repair ground or replace wire.

Faulty wire - Replace.

Remote control and/or

battery holder (including

switch) is not functioning

properly.

Remote control lights but

no spark or ﬂame. (Remote is

locked out).

- Reset by turning power source off then on.

Battery holder (including switch)

or remote has low battery.

- Replace batteries.

Error with synchronizing. - Reset battery holder (including switch) and remote control.

Remote too far away from

battery holder (including switch).

Refer to “wiring diagram” section in the Installation manual.

If back up batteries are installed, they must also be

removed to re-program

note:

Flames are very

aggressive.

Door is open. - Ensure door is secured properly. If not rectiﬁed, contact a

qualiﬁed technician.

Appliance won’t

perform any

functions.

No power to the system.

- Check breaker to verify it’s in the “on” position.

Battery holder (including switch)

in wrong position (if equipped).

- Verify that the 3 position switch on the battery holder (including

switch) is in the remote position (middle).

Battery holder, battery holder

(including switch) and/or remote

control isn’t operational.

Check battery power and battery orientation.

lazy, transparent ﬂame

W415-2760 / D / 04.20.21

warranty

8.0 warranty

Continental® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty

is not necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty

claim. Continental® reserves the right to have its representative inspect any product or part thereof prior to honouring any

warranty claim. Provided that the purchase was made through an authorized Continental® dealer your appliance is subject

to the following conditions and limitations:

Warranty coverage begins on the date of original installation. This factory warranty is non-transferable and may not be

extended whatsoever by any of our representatives. The gas appliance must be installed by a licensed, authorized service

technician or contractor. Installation must be done in accordance with the installation instructions included with the product

and all local and national building and ﬁ re codes. This limited warranty does not cover damages caused by misuse,

lack of maintenance, accident, alterations, abuse or neglect, and parts installed from other manufacturers will nullify this

warranty. This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive

heat, abrasive and chemical cleaners nor chipping on porcelain enamel parts, mechanical breakage of Phazer™ logs and

embers. In the ﬁ rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in

material or workmanship provided that the product has been operated in accordance with the operation instructions and

under normal conditions. After the ﬁ rst year, with respect to this Limited Warranty, Continental® may, at its discretion, fully

discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price

of any warranted but defective part(s).

Continental® will not be responsible for installation, labour, or any other expenses related to the reinstallation of a warranted

part and such expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited

Warranty, Continental®’s responsibility under this warranty is deﬁ ned as above and it shall not in any event extend to

any incidental, consequential or indirect damages. This warranty deﬁ nes the obligations and liability of Continental® with

respect to the Continental® gas appliance and any other warranties expressed or implied with respect to this product,

its components or accessories are excluded. Continental® neither assumes, nor authorizes any third party to assume,

on its behalf, any other liabilities with respect to the sale of this product. Continental® will not be responsible for: over-

ﬁ ring, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains,

inadequate vents or ventilation, excessive venting conﬁ gurations, insufﬁ cient makeup air, or negative air pressures which

may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc. Any damages to

the appliance, combustion chamber, heat exchanger, plated trim or other components due to water, weather damage,

long periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of Continental®. All

parts replaced under the Limited Warranty Policy are subject to a single claim.

All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation. The

manufacturer may require that defective parts or products be returned or that digital pictures be provided to support

the claim. Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be

defective, the manufacturer will repair or replace such defect. Before shipping your appliance or defective components,

your dealer must obtain an authorization number. Any merchandise shipped without authorization will be refused and

returned to sender. Shipping costs are not covered under this warranty. Additional service fees may apply if you are seeking

warranty service from a dealer. Labour, travel diagnostic tests, shipping and other related charges are not covered by this

warranty.

Continental® products are manufactured under the strict standard of the world recognized ISO 9001 : 2015 Quality

Management System.

Continental® products are designed with superior components and materials assembled by trained craftsmen who take great

pride in their work. The burner and valve assembly are leak and test-ﬁ red at a quality test station. The complete appliance is

again thoroughly inspected by a qualiﬁ ed technician before packaging to ensure that you, the customer, receives the quality

product that you expect from Continental®.

The following materials and workmanship in your new Continental® gas appliance are warranted against defects for a

period of 5 years, this covers: combustion chamber, heat exchanger, stainless / steel burner, Phazer™ logs and embers,

rocks, ceramic glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enameled components and

aluminum extrusion trims.*

Electrical (110V and millivolt) components and wearable parts are covered and Continental® will provide replacement parts

free of charge during the ﬁ rst year of the limited warranty. This covers: blowers, gas valves, thermal switches, switches,

wiring, remote controls, ignitors, gaskets and pilot assemblies.*

Any labour related to warranty repair is not covered.

* Construction of models vary. Warranty applies only to components included with your speciﬁ c appliance.

Continental® Gas Appliance Limited Warranty

Conditions and Limitations

All speciﬁ cations and designed are subject to change without prior notice due to on-going product improvements. Continental® is a

registered trademark of Wolf Steel Ltd.

La page charge ...

Continental Fireplaces CBL46NTE Manuel utilisateur

Marque: Continental Fireplaces

Modèle: CBL46NTE

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

CBL36NTE-1

Télécharger le PDF

rapport

dans d''autres langues

English: Continental Fireplaces CBL46NTE User manual

Continental Fireplaces CBL46NTE Manuel utilisateur

Ce manuel convient également à

Continental Fireplaces CBL46NTE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents