Triax TECW 211 Manuel utilisateur

User manual

TRIAX TECW 211

Article Article no.

TRIAX

TE

CW

211

Ethernet over coaxial cable adapter & WIFI access

Ethernet over coaxial cable adapter & WIFI access Ethernet over coaxial cable adapter & WIFI access

Ethernet over coaxial cable adapter & WIFI access point

pointpoint

point

310411

Version A Date 12/2016 EN

User manual

EN

2

Attention! / Achtung! / Consignes de sécurité!

EN

Failure to comply

Failure to complyFailure to comply

Failure to comply

with the specifie

d precautionary measures may cause serious injury to persons or damage to

property. The installation and commissioning may only be performed by suitably qualified persons, technicians or

installers in compliance with safety regulations.

Damage due to improper installation and commissioning, defective connectors on cables or any other incorrect

handling will void the warranty.

CAUTION: The safety requirements are according to EN 60728-11 and must be observed.

• Disconnect mains power before working on electrical systems.

• Any additional electrical wiring requirements should always be installed by a suitably qualified person(s).

Installation or service work should NEVER be undertaken during electrical / thunderstorms.

Subject to change without prior notice !

DE

Gewährleistung

Gewährleistung Gewährleistung

Gewährleistung

Die gesetzliche Gewährleistung nach Paragraph 437 BGB beträgt 24 Monate.

Bei unsachgemäßer Installation und Handhabung erlischt jeglicher Garantieanspruch.

Bestimmungsgemäße

Und sachwidrige Verwendung

Die Montage und Inbetriebnahme darf nur von eingewiesenen Personen, Technikern

oder Installateuren unter Beachtung der Sicherheitsbestimmungen durchgeführt werden.

Schaden durch falsche Montage und Inbetriebnahme sowie durch unsachgemaβe Handhabung fuhren zum Erlöschen

des Garantieanspruchs.

FR

Veillez à bien respecter

Veillez à bien respecterVeillez à bien respecter

Veillez à bien respecter

les consignes de sécurité ci

-

dessous. Leur non

-

respect peut provoquer des dommages

matériels ou corporels.

L’installation et la mise en route ne peuvent être effectués que par des techniciens ou des installateurs qualifiés en

respectant les consignes de sécurité.

La garantie ne sera pas appliquée lors de dégâts causés par une erreur de montage, de mise en route ou par un

mauvais raccordement ou toute autre manipulation incorrecte.

PRUDENCE : avant toute intervention, votre installation doit être conforme aux exigences définies par les dispositions

Européennes EN 50083 (conformité des installations collectives) et EN 60065 (normes en vigueur pour la protection

électrique).

• Débranchez l’appareil avant toute intervention, car certains composants sous tension sont dangereux

(risque d’électrocution).

Toute intervention sur l’installation ou travaux de maintenance sont à proscrire en cas d’orage.

Table of contents / Inhaltsverzeichnis / Sommaire

Attention! / Achtung! / Consignes de sécurité! ................................................................................ 2

1. Introduction ...................................................................................................................... 4

1.1 Packing List ...................................................................................................................... 5

1.2 Connectors and LED’s ....................................................................................................... 6

2. First time configuration..................................................................................................... 7

3.1 Login Password .............................................................................................................. 11

3.2 Alternative way to find the device.................................................................................... 11

User manual

3

EN

4. Quick settings by using the Wizard ................................................................................. 12

5. Status – device status .................................................................................................... 14

5.1 Status – Network Status ................................................................................................. 15

5.2 Status – MoCa Rates ...................................................................................................... 15

6. Network .......................................................................................................................... 16

7. WLAN .............................................................................................................................. 17

7.1 WIFI 5GHz Basic .............................................................................................................. 18

7.2 WIFI 5GHz Advanced ....................................................................................................... 19

7.3 WiFi 5GHz Security .......................................................................................................... 20

7.4 WiFi 5GHz Access Control............................................................................................... 21

7.5 WiFi 5GHz WPS ............................................................................................................... 22

7.6 WiFi 5GHz Status ............................................................................................................ 23

7.7 WIFI 2.4GHz Basic ........................................................................................................... 23

7.8 WIFI 2.4GHz Advanced .................................................................................................... 25

7.9 WiFi 2.4GHz Security ....................................................................................................... 26

7.10 WiFi 2.4GHz Access Control............................................................................................ 27

7.11 WiFi 2.4GHz WPS ............................................................................................................ 28

7.12 WiFi 2.4GHz Status ......................................................................................................... 29

8. MoCA Settings ................................................................................................................ 30

8.1 MoCA Security ................................................................................................................ 31

9. Admin ............................................................................................................................. 32

9.1 Admin - Reset .................................................................................................................. 32

9.2 Admin - Password ........................................................................................................... 32

9.3 Admin – Upgrade Firmware............................................................................................. 33

9.4 Admin – Backup .............................................................................................................. 34

9.5 Admin – Time Zone ......................................................................................................... 34

10. Specifications ................................................................................................................. 35

User manual

EN

4

1. Introduction

TECW 211 installation example (2 devices to create a network)

The TECW 211 is a multi-purpose Ethernet over coaxial cable bridge device. It can be used in a number of

different ways to deliver Gigabit Ethernet connection via an existing coaxial (TV aerial or cable TV) connection. It

offers Wi-Fi dual band 2.4 and 5GHz in order to improve your local WLAN Wi-Fi coverage in your home

installation

It can be used as either a sender or receiver but it will need to be used with at least one other TRIAX Ethernet

over Coax compatible device. This can be either

• TEOC 211: Ethernet over Coax device (compatible with cable or terrestrial TV signals)

• TECW 211: Ethernet over Coax + Wi-Fi dual band device (compatible with cable or terrestrial TV

signals)

A Maximum of 16 TEOC 211 or TECW 211 devices can be used in any in home network

Each being able to send and receive Gigabit Ethernet via the existing TV aerial or cable TV cabling structure that

is already installed in the home

The following pages show the most common configurations. For more detailed installation examples please visit

our web site www.triax.com

User manual

5

EN

1.1

Packing List

Before starting the installation of the device, please make sure the package contains the following

items:

1 x TECW 211

1 x Power Adapter

100-240 VAC / 50-

60Hz to 5V DC with

EU and UK plug

1 x RJ 45 cable, Cat

5e, 1.0m.

1 x white coaxial

cable, 1.0m, class

B 75 ohms with 1x

F male Connector

and 1 x IEC male

connector

1 x IEC male to F

male adapter

1 x IEC female to F

male adapter

User manual

EN

6

1.2

Connectors and LED’s

WPS button WPS push button

Power

Solid Green

Off

Device is ON

Device is OFF

Link between

devices

S

olid Green

Off

Device is connected to another similar device

and a network is created

Device is NOT connected to another similar

device and a network is created

LAN 1

Solid Green

Blinking Green

Off

The Ethernet is plugged in and connected to

the network device

Receiving Ethernet traffic

The Ethernet is not plugged in

LAN 2

Solid Green

Blinking Green

Off

The Ethernet is plugged in and connected to

the network device

Receiving Ethernet traffic

The Ethernet is not plugged in

WIFI

Solid Green

Blinking Green

Off

WI

-

FI is ON

WI-FI has activity

WI-FI is OFF

WPS

Solid Green

Blinking Green

Off

WPS process successful

WPS in progress

WPS not initialized

Front panel

User manual

7

EN

POWER

switch

Turn device ON/OFF

DC

12V/1.5A

DC plug, plug in the supplied power supply 12V

RESET Reset PIN hole, press 5 seconds to reset to factory default.

Switch Turn on/off the lamps in the front panel

LAN 2 10/100/1000 Mbps, RJ45

LAN 1 10/100/1000 Mbps, RJ45

TV+WWW

Offer TV + Ethernet signals to create the local

network. See

connection examples.

TV+WWW connectors from several TEOC 211/TECW 211 need to

be connected together to create the private network.

TV

Offer TV signals to be connected to TV set (output) or to the

terrestrial / cable arrival signal (input). See connection examples.

2. First time configuration

•

Quick connection

In all cases (terrestrial or cable network), the first TEOC 211 adapter needs to be connected to your

house Internet access (Cable modem, ISP modem,…) via the supplied Ethernet patch cord, to get

an Ethernet signal into the system.

• Connexion to a terrestrial television distribution system

Make a connection from a free OUTPUT on the TV aerial distribution amplifier to the “TV+WWW” F

connector on the TEOC 211 adapter. It is essential that the first TEOC 211 adapter is only

connected to an OUTPUT port of the amplifier, as the Ethernet over coax signal cannot pass

through any amplifier.

Rear panel

User manual

EN

8

At the second end where the Ethernet and Wi

-

Fi signals are wanted, you need to use a TECW 211

(with build-in Wi-Fi extender). On this second device, connect the “TV+WWW” F connector to the

wall outlet (TV port).

To remake the connection to the TV or a DVB-T set top box, so that the signal is passing through

the TECW 211, use the supplied coaxial fly lead between the TECW 211 “TV” port and your TV or

STB.

Connect any Ethernet devices – Smart TV, Game console, Blu-ray player, IP Set top Box etc. using

the supplied Ethernet patch cord. Connect your wireless devices by reading the instructions

detailed later in this user manual concerning the Wi-Fi settings.

Power up the 2 devices (TEOC 211 and TECW 211), the link between the devices is established

automatically, this is confirmed when the LED is ON. (It may take a few minutes to link.). The

terrestrial or cable TV signal can be passed through the device.

•

Connexion to a cable television distribution system

Make a connection from a free OUTPUT on the CATV distribution amplifier to the “TV+WWW” F

connector on the TEOC 211 adapter. It is essential that the first TEOC 211 adapter is only

connected to an OUTPUT port of the amplifier, as the Ethernet over coax signal cannot pass

through any amplifier.

User manual

9

EN

At the second end where the Ethernet and Wi

-

Fi signals are wanted, you need to use a

TECW 211

(with build-in Wi-Fi extender). On this second device, connect the “TV+WWW” F connector to the

wall outlet (TV port).

To remake the connection to the TV or a DVB-C set top box, so that the signal is passing through

the TECW 211, use the supplied coaxial fly lead between the TECW 211 “TV” port and your TV or

STB.

Connect any Ethernet devices – Smart TV, Game console, Blu-ray player, IP Set top Box etc. using

the supplied Ethernet patch cord. Connect your wireless devices by reading the instructions

detailed later in this user manual concerning the Wi-Fi settings.

Power up the 2 devices (TEOC 211 and TECW 211), the link between the devices is established

automatically, this is confirmed when the LED is ON. (It may take a few minutes to link.). The

terrestrial or cable TV signal can be passed through the device.

If you have more devices to connect onto your network, repeat the second device operation.

The schematics below illustrate how to create your fist network. More schematics examples are

available on www.triax.com

Before using the device, we recommend you to directly connect your PC to the LAN of the device

using an Ethernet cable. Usually your computer is setup to obtain an IP address automatically and

you don’t need to change it.

User manual

EN

10

3. Detailed settings

In order to setup the TECW 211 device, you need to know its IP address. Connected to your local

network (WLAN), the TECW 211 will get automatically its IP address from your WLAN thanks to

the DHCP function.

The “UdpDiscovery” PC Tool program supports Windows 7/8/10.

To find the TECW 211 IP address, you can:

• run the TRIAX “UdpDiscovery” PC Tool from the TRIAX web site, install it on your PC to

find and configure the TECW 211.

• Use the Windows UPnP to find the device.

Double-click the device to open the web page of the device. Click “Refresh” to renew the window.

User manual

11

EN

3.1

Login Password

When entering the device web page, the username and password are required when login this

device. Please enter the default username “admin

adminadmin

admin” and the default password “admin

adminadmin

admin” to login.

3.2

Alternative way to find the device

Besides the discovery tool, the Windows UPnP can also find the TECW 211 device. In Windows

bar, Click “File Browser” icon to open File Browser.

The device should appear in “Network” field.

Double-click it to open the login page and

enter username/password to

enter the web page.

User manual

EN

12

4. Quick settings by using the Wizard

In the welcome page, click “Next” to begin the setting.

In the first page, modify the network name (SSID) for Wi-Fi 5GHz. Change the encryption if you

want to, but WPA2-AES is recommended for the safer security. Enter the Pre-Shared Key (security

key) for the encryption.

User manual

13

EN

Wizard continued

In the second page, modify the network name (SSID) for Wi-Fi 2.4GHz. Change the encryption if

you want to, but WPA2-AES is recommended for the safer security. Enter the Pre-Shared Key

(security key) for the encryption.

In the third page, keep MoCA Channel

“NULL” and the device will search the available MoCA

channel. Select “Disabled” or “Enabled” to turn off/on the MoCA network security. If enabled, the

“Network Password” must be entered to connect to the secured MoCA network.

User manual

EN

14

Wizard continued

In the final page, the settings are listed to confirm. Click the “Finish” button and wait 60 seconds

that the TECW 211 is being configured. Then your settings are applied from the TECW 211.

5. Status – device status

The device status such as firmware version, MoCA link status and more are displayed in this page.

User manual

15

EN

5.1 Status – Network Status

The network status of this device is displayed in this page.

5.2

Status

–

MoCa Rates

The MoCA rates between devices like TEOC 211 or TECW 211 are displayed in this page. This will

give you the bandwidth shared between devices.

User manual

EN

16

6. Network

This page shows you the network parameters set in your device. You can change them according

to your local network. But you can let your device “talk” to your WLAN and get automatically its

configuration thanks to the DHCP protocol.

Item

ItemItem

Item

Description

DescriptionDescription

Description

Auto IP

Enable it to use an IP Address “169.254.x.x” when there is no DHCP server

in the network.

IP Address

Disable it to change IP Address manually.

Subnet Mask

If you wa

nt to manually change the IP Address for the device, enter the

new IP Address in this field.

Default Gateway

The defaults value is “192.168.1.1”.

Primary DNS

Enter the new Subnet Mask to change the current value.

Secondary DNS

Enter the gateway address

of the LAN.

User manual

17

EN

7. WLAN

To quickly establish a wireless network on this device with minimum settings, three setting need to

be done. Please refer to the following sections for the settings descriptions.

1.

1.1.

1. BASIC Network name:

BASIC Network name:BASIC Network name:

BASIC Network name: Enter the preferred name as the Wireless network name (SSID). If

you want to extend your WLAN coverage using the TECW 211 to broadcast Wi-Fi over

non-covered areas from your WLAN, duplicate your WLAN SSID information.

2.

2.2.

2. BASIC Channel number:

BASIC Channel number:BASIC Channel number:

BASIC Channel number: Select the 5GHz and 2.4GHz Channel number.

3.

3.3.

3. Wi

WiWi

Wi-

--

-Fi

Fi Fi

Fi –

––

–

Security Encryption:

Security Encryption:Security Encryption:

Security Encryption: Select "WPA2" as the Encryption, Personal (Pre-Shared Key)

as the Authentication, "AES" as the Cipher suite, "Passphrase" as the Key format, and

then enter the Pre-Shared Key. Both 2.4GHz and 5GHz WLAN security are needed to

setup.

User manual

EN

18

7.1

WIFI 5GHz

B

asic

Configure the WLAN basic settings for the device.

Item

ItemItem

Item

Description

DescriptionDescription

Description

Disable Wi

-

Fi

Interface

Check the box to disable 5GHz WLAN.

Network Name

Input name for this Wi

-

Fi network. This name also called SSID will be

scanned by the Wi-Fi station/client device.

Channel Width

Select the channel width. 80MHz is recommended for the high data rate.

Control

Sideband

This device will automatically choose the sideband for 40MHz or 80MHz

bandwidth.

Channel Number

Select the c

hannel number for the WLAN. If “Auto” is selected, the device

will scan the channels and select the unused channel. This is the preferred

setting.

Radio Power (%)

Select the smaller percentage to drop the radio power to reduce the

WLAN coverage. The default value is 100%.

Show Wi

-

Fi

Clients

Click this button to open the active WLAN client table. All associated

WLAN clients will be displayed in the table.

When “Show Wi

-

Fi Clients” button is clicked, the Wi

-

Fi

-

associated clients table

is pop

-

up like b

elow

User manual

19

EN

7.2

WIFI 5GHz Advanced

The default setting of Wi

-

Fi Advanced setting is recommended. Do not change them.

Item

ItemItem

Item

Description

DescriptionDescription

Description

Fragment

Threshold

The fragmentation threshold determines the size at which packets are

fragmented (sent as several pieces instead of as one block). Use a low

setting in areas where communication is poor or where there is a great

deal of radio interference.

RTS Threshold

The RTS threshold determines the packet size at which the radio issues a

request to send (RTS) before sending the packet. A low RTS Threshold

setting can be useful in areas where many client devices are associating

with the device, or in areas where the clients are far apart and can detect

only the device and not each other. You can enter a setting ranging from 0

to 2347 bytes.

Beacon Interval

Beacons are the packets sending by Access point to synchronize the

wireless network. The beacon interval is the time interval between

beacons sending by this AP device. The default and recommended

beacon interval is 100 milliseconds.

Data Rate

Select WLAN physical data rata. The “Auto” option is recommended.

Broadcast SSID

Enable it and the WLAN clients can scan and see this WLAN name.

Disable it and the WLAN clients won’t see this WLAN name and have to

manually input this WLAN name for the association.

After changing the parameters, click “Apply” button to apply the changes.

User manual

EN

20

7.3

Wi

Fi 5GHz Security

Setup the Wi

-

Fi security

.

Item

ItemItem

Item

Description

DescriptionDescription

Description

Encryption

Select the Wi

-

Fi secure method and algorithm.

None: Wi-Fi 5GHz is not secured. It is not recommended.

WPA2-AES: Use WPA2 and AES algorithm to secure Wi-Fi 5GHz.

WPA/WPA2 Mixed –TKIP AES: This device accepts WPA/WPA2 and

TKIP/AES algorithm to secure Wi-Fi 5GHz.

Pre

-

Shared Key

Format

(password)

Select Passphrase or HEX (64 characters).

Pre

-

Shared Key

(password)

Enter the key for WPA. The WLAN clients must have the same key to

associate to this AP device.

For Passphrase format, enter 8~63 characters.

For HEX (64 characters), enter 64 hexadecimal character.

Af

ter changing the parameters, click “Apply” button to apply the changes.

La page charge ...

Triax TECW 211 Manuel utilisateur

Triax TECW 211 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents