Parts & Operations Manual
Manuel de pièces et d’opérations
Power Clean 1200 XT
Box Extractor
Code: 19386 (100 psi) / 19387 (500 psi)
Serial Number:
Numéro de série : _____________________
Date of Purchase:
Date d’achat : ________________________
More info / Plus d’info : www.dustbane.ca
2015-09
2
3
ENGLISH
Safety, Operations and Maintenance
Save these instructions. Read and follow all warnings and cautions before using this carpet
extractor. This unit is intended for commercial use.
This box extractor will aord you many years of trouble-free operating satisfaction, provided it is given proper care. All parts have
passed rigid quality control standards prior to their assembly to produce the nal product. Prior to packaging, your box extractor
was again inspected for assurance of awless assembly.
This box extractor is protectively packed to prevent damage in shipment. We recommend that upon delivery, you unpack the unit
and inspect it for any possible damage. Only a visual examination will reveal damage that may have occurred during shipping.
Important Safety Instructions
WARNING: Electric shock may occur if used on wet surfaces. Store indoors.
To reduce the risk of re, electric shock or injury:
• Use only as described in this manual. Use only the attachments recommended by the manufacturer.
• Test all outlets with an outlet tester before plugging machine into any outlet. Plug cord into the nearest grounded outlet.
• DO NOT unplug by pulling on the cord, grasp the plug. DO NOT pull unit by the cord.
• Keep cord away from heated surfaces.
• Never attempt adjustments or repairs while the machine is plugged in.
• DO NOT use if cord or plug are damaged.
• DO NOT use outdoors, in standing water on wet surfaces.
• Pay close attention when using machine near children.
• DO NOT pick up ammable or combustible materials or use machine where they may be present.
• DO NOT leave machine outdoors, in extreme heat or cold. Harsh weather elements will damage components and void
warranty.
• Lift using only the appropriate handles.
• Always wear the appropriate clothing and safety equipment when operating the machine.
• Keep all body parts, hair and loose clothing away from openings and moving parts.
• Use extra care when cleaning stairs. Never move the machine up or down stairs with uid in the machine.
• Use common sense to protect yourself and others from injury when using the machine.
Grounding Instructions
IMPORTANT: Improper grounding method can result in a risk of electrical shock.
The machine must be grounded.
Electrical equipment must be grounded. If the machine should malfunction or breakdown, grounding provides a path of least
resistance for electrical current to reduce the risk of electric shock. The Carpet Extractor is equipped with a cord containing a
grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
If repair or replacement of the cord or plug is necessary, DO NOT connect the grounded wire to a at bed terminal. The grounding
wire is the wire with insulation and an outer green surface, with or without yellow stripes.
WARNING: Improper connection of the equipment grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the appliance - if it will not t the outlet, have a proper outlet
installed by a qualied electrician. RINTENDED FOR USE ON A NOMINAL 120-VOLT SUPPLY CIRCUIT: the carpet
extractors have a grounding attachment plug that looks like the plug illustrated. Make sure that the carpet
extractor is connected to an outlet having the same conguration as the plug. No adaptor should be used with
these carpet extractors.
4
ENGLISH
Set-Up / Prepare Unit for Use
IMPORTANT: Do not use on wet surfaces. Do not expose to rain. Store indoors.
• All Carpet Extractors, no matter what the time of year, are shipped with antifreeze in the solution lines. Prior to rst use, ll
the tank with one quart of warm water. Attach the hose and using the hand tool wand, ush out the system by spraying the
one quart of water through the pump.
• Attach the 1-1/2 inch vacuum hose and the brass quick disconnect.
• Fill the base unit (the recovery tank must be removed) with warm water (less than 100 degrees Fahrenheit). Fill to
approximately 4 inches from the top. Pre-spray a liquid detergent made for carpet cleaning or upholstery on carpet and
agitate carpet. Next, use clean water from solution tank to extract – this procedure is highly recommended. Note: read and
mix your pre-spray solution to the dilution ratios as directed.
• Be sure to replace any lters back into the machine prior to use.
• Do not use citrus acid, buterol or harsh degreasers inside the machine.
Electrical
Plug cord(s) into 20 AMP grounded wall outlet(s). 20 AMP circuits are normally found in kitchens and bathrooms. Never remove
ground prong from the plug. If a circuit breaker trips during operation, turn machine o, reset the breaker and move the electrical
cord to a dierent outlet and resume operation.
Vacuum System
The extractor uses a dual vacuum motor system that provides outstanding water lift and air ow.
Vacuum Float Assembly Warning System
The oat assembly on the vacuum stand pipe prevents the waste tank from overowing the stand pipe and damaging the vacuum
motors. Motors will reach a fast, high-pitched sound alerting you when the recovery tank is about to over ow. When this happens,
immediately turn OFF the vacuum switches and empty the waste tank.
The oat assembly has a lter to prevent lint and debris from entering the stand pipe. Refer to the “Maintenance” section for removal
and proper cleaning.
It is also necessary to use a defoamer to eliminate foam build-up in the recovery tank which could lead to foam/moisture
entering the vacuums and contributing to early failure of the vacuum motors.
If moisture does enter the vacuum motors, contact an authorized service center. To prevent moisture from damaging the vacuum
motors during storage, empty the recovery tank and store with the lid open.
Shutdown Procedures
When nished cleaning, turn OFF all switches.
• Disconnect the solution hose and vacuum hose from the cleaning tool. Pull the valve
trigger to release pressure from the hose before disconnecting the solution hose
from the cleaning tool.
• Disconnect the clear view in-line lter from the vacuum hoses and clean the lter as
needed.
• Disconnect the vacuum hose and solution hose from the machine.
• If water remains in the solution tank, use the short vacuum hose and vacuum the
excess water from the tank.
• Disconnect the power cords from the outlets and from the machine.
• Remove the oat assembly from the recovery tank and clean lter as needed. Replace
oat assembly and tank lid.
5
ENGLISH
• Drain any remaining water from the recovery tank and dispose of in a sanitary drain. DO NOT
use the same bucket to drain the tank that you used to ll the tank.
• Roll up all hoses and tools. Collect and store extractor, all tools and accessories.
Maintenance
Regular maintenance is required to keep your Carpet Extractor in proper working condition. Failure to properly
maintain your machine could void warranty. Thoroughly clean all equipment and accessories after each use:
• Rinse the solution and recover tanks with clean water.
• Flush the pump system with clean water, including all hoses and wand(s).
• Do not allow water to remain in the tanks after use.
• Lubricate all quick disconnects with WD-40 or similar lubricant.
• Clean vacuum oat assembly screen.
WARNING: Disconnect electrical power cord before performing any service or maintenance inside the machine base
or before testing or repairing switches or power cords. Failure to do so may result in severe personal injury or death.
Operation Interval
Clean chemical feed lter Daily - after each job
Clean vacuum assembly screen Daily - after each job
Rinse out recovery tank Daily
Flush solution tank and pump Daily
Clean pump-inlet lter Weekly - as needed
Clean Fresh Water Tank Filter
The fresh water tank lter is located at the bottom of the solution tank. Unscrew the lter counterclockwise and rinse with fresh
water. If necessary, use a tooth brush to remove detergent build-up. Note, a heavy build-up is a warning sign that the solution
system should be ushed. See the “Flush Chemical System” section.
Clean Vacuum Float Assembly Screen
Inside the recovery tank, on top of the stand pipe, is the vacuum oat assembly. It functions to prevent debris and water from being
sucked into the vacuum motors. Operating the Carpet Extractor without the oat assembly or with a poorly maintained assembly,
will greatly decrease the life of the vacuum motors and will void the warranty.
If debris builds up on this lter, it will reduce the vacuum air ow and may cause a signicant decrease in the rate of water recovery.
If debris prevents the oat ball from moving or seating inside the assembly, it may not stop the airow when the tank lls with water
and the water will be sucked in the vacuums and blow out the exhaust.
To clean, twist o the oat assembly from the stand pipe and clean the screen. Pull bers and
lint o and rinse with clean water. Push the assembly back onto the stand pipe and replace the
recovery tank lid.
This screen should be cleaned frequently if the Carpet Extractor is being operated in an
environment which has an abnormal build-up of lint and debris, such as cleaning newly installed
carpet. Loss of vacuum is most normally associated with lint build-up in this lter at the top of
the vacuum stand pipe.
6
ENGLISH
Rinse Out Recovery Tank
Build-up of ne silt and debris can damage the auto-dump pump and dump valve. Clean out the recovery tank on a regular basis to
extend the life of these components as well as keep the tank and machine smelling better.
To rinse out recovery tank, remove the recovery tank lid and open the dump valve. Place a bucket under the dump valve. Use a hose
to rinse the dirt and debris out of the recovery tank. Close the dump valve and spray the tank with deodorizer or disinfectant.
Proceed to waste pump cleaning and replace the recovery tank lid. Dispose of dirty water and debris.
Clean Pump Inlet Filter
CAUTION: before proceeding with this procedure, make sure both the power cords are disconnected.
Solution tank
Latch
Base
• To examine the lter, open the solution tank lid on the front of the
machine. The lter is in the bottom of the solution tank.
• Grasp the lter cap and unscrew the lter from the brass nipple by
turning counter-clockwise. Clean or replace the lter as needed.
• Tilt the tanks back onto the base and secure the latch.
1/4” Acorn Strainer
Part No. 10-0845
WD-40 Vacuum Motors
Should moisture ever enter the vacuum motors, completely drain the recovery tank, open the recovery tank lid, remove the vacuum
oat assembly, turn on both vacuum motors and spray a ve (5) second burst of WD-40 into the standpipe. Continue to run the
vacuum motors for at least three (3) minutes.
To prevent moisture from damaging the vacuum motors during storage, empty the recovery tank and store with the lid open.
7
ENGLISH
Storage and Freeze Protection
You must winterize your Carpet Extractor to protect the pump system from freezing and also damage being caused to t
tings and valves. Damage due to freezing is not covered under the Warranty. Store your extractor in temperatures over 40 degrees
Fahrenheit. If you plan on storing your extractor in freezing conditions or for a long period of time, the following procedure should
help prevent your Carpet Extractor from freezing and prevent pump and seals from drying out.
Recommended Procedure for Storage
• In a separate container, mix 1/2-gallon of water with 1/2-gallon of RV Water System Antifreeze. Mix well and pour into the
solution tank.
• Connect the pressure hose to the female quick disconnect (QD) on the front of the machine. Insert an open-ended male QD
into the female QD on the end of the pressure hose.
• When primed, turn down the pressure to 100 PSI.
• Disconnect the open-ended QD and connect the solution hose to the male QD at the auto-ll/chemical feed connection.
CAUTION: applying high pressure (over 100 PSI) to the chemical feed system will damage the mechanism.
• With the chemical feed supply tube at the bottom of the solution tank, turn on the pump and allow to circulate for 10
minutes. Check to make sure the chemical supply tube is drawing the antifreeze solution. This will introduce antifreeze into
the chemical feed system.
• Disconnect the solution hose from the chemical feed and allow the system to bypass for 10 minutes. This will work antifreeze
into the pressure gauge.
• Attach and wands and hand tools that will also be stored with the Carpet Extractor. Open the valve for 30 seconds, directing
the spray to the solution tank. Disconnect the hose and with the valve open and the jets pointing down, depress the dimple
on the male QD. This will drain the solution out of the tool. Drain thoroughly before storing.
• Turn o the pump and disconnect all hoses and tools. Vacuum out the solution tank and thoroughly drain the recovery
tank and vacuum hose.
• To return to service, ush the pressure system by repeating the above steps, using fresh water in place of antifreeze.
Troubleshooting Guide
CAUTION: Always disconnect power cord before servicing.
WARNING: Repairs should only be performed by an authorized service center.
Vacuum System
PROBLEM: No vacuum/Weak Vacuum
CAUSE SOLUTION
1. Vacuum Tank Full 1. Empty Tank
2. Float Assembly Tank Screen Dirty 2. Clean the Screen with Water
3. Float Ball Stuck 3. Tap Float to Unstick then Clean
4. Damaged or Loose Vacuum Hose 4. Attach or Replace
5. Dump Valve Open 5. Close Valve
6. Access Lid not Sealed 6. Replace Gasket
7. Vacuum Hose Clogged 7. Clear Debris
8. Air Intake Grid Clogged 8. Clean
9. Leak in Recovery Tank 9. Clean and Dry Area, Patch with Silicone
10. Water Coming out of Vacuum Exhaust 10. Use a Low Foaming Detergent
Electrical System
PROBLEM: Unit will not turn on
CAUSE SOLUTION
1. Extension Cord not Plugged In 1. Check if Machine and Cord are Plugged In
2. Switch not in the “On” Position 2. Check Switches, Replace if Necessary
3. Building Circuit Overloaded 3. Reset Circuit
4. Wiring Connections Loose 4. Unplug Machine and Check for Loose Wires
8
ENGLISH
Electrical System
PROBLEM: Burning Smell
CAUSE SOLUTION
1. Vacuum Motor Hung Up 1. Replace Vacuum Motor
2. Pump Motor Hung Up 2. Replace Pump
Pump System
PROBLEM: Pump is not running properly
CAUSE SOLUTION
1. No Power to the Pump 1.Check the Electrical System
2. Jets on Wand are Clogged 2. Clean Jet Filters
3. In-Line Water Filter is Clogged 3. Clean In-Line Filter
4. Debris in Solution Tank Covering Inlet 4. Clear Debris
5. Kinked or Loose Hose 5. Check and Replace Hoses if Necessary
6. Pump Failed 6. Replace Pump
7. Quick Disconnects are not Completely Locked Together 7. Snap Quick Disconnects Together\
8. Heater is Clogged with Deposits 8. Flush Heater with System Maintainer or Replace if Necessary
9. Pump is Pulsating 9. Check for Clogged Jets and Clean
10. Auto Prime Valve is Open 10. Close Valve
9
TEN YEARS UNCONDITIONAL WARRANTY ON ALL POLYETHYLENE ROTATIONAL MOLDED RESERVOIRS TO BE FREE
FROM ALL CRACKS AND/OR CORROSION.
THREE YEARS WARRANTY ON ALL EQUIPMENT PARTS AGAINST DEFECTS IN MATERIAL AND WORKMANSHIP UNDER
NORMAL USE AND CARE WITH THE EXCEPTION OF ANY RUBBER COMPONENTS AND SPRINGS.
ONE YEAR UNCONDITIONAL WARRANTY ON LABOUR AND EQUIPMENT PARTS UNDER NORMAL USE AND CARE
WITH THE EXCEPTION OF ANY RUBBER COMPONENTS AND SPRINGS.
DUSTBANE PRODUCTS LIMITED warrants each new unit of Dustbane Equipment accompanied by this Warranty, including acces-
sories thereto (but except any rubber parts and springs) manufactured or supplied by Dustbane Products Limited and delivered
to the original retail purchaser by an authorised Dustbane distributor, to be free from defects in material and workmanship under
normal use and care. The obligation of Dustbane Products Limited under this Warranty shall be limited to repairing or replacing,
at its option, any part or parts of Dustbane Equipment which shall have been returned to a Dustbane authorised repair depot, and
which, upon examination, shall disclose to the satisfaction of Dustbane Products Limited to have been defective, whereupon any
required repair or replacement shall be made by such Dustbane authorised repair depot.
THE obligation of Dustbane Products Limited to the repair or replacement of defective parts is further limited to :
• to the cost of parts and labour for returns of polyethylene rotational moulded reservoirs made within ten (10) years
• to the cost of parts only for returns made within three (3) years
• the cost of parts and labour for returns made within twelve (12) months based on Dustbane’s Labour Rates all as
calculated from the delivery date of such unit of Dustbane Equipment to the original retail purchaser.
THE provisions of this Warranty shall not apply to:
• any unit of Dustbane Equipment which has been subject to misuse, negligence or accident, or which shall have been
repaired or altered by a person or persons outside a Dustbane authorised repair depot, in any way so as, in the
judgement of Dustbane Products Limited, to a ect adversely its performance and reliability
• normal maintenance services and the replacement of service items (including but not limited to electric cord,
painted parts, any rubber parts and springs, switch and bearings) made in connection with such services as required
in the Dustbane Recommended Maintenance Schedule
NEITHER Dustbane Products Limited nor any authorised Dustbane distributor shall be liable for any claims or damage (including
but not limited to consequential damage and loss of income) resulting from any failure of Dustbane Equipment, whether caused by
negligence or otherwise; Nor for claims or damages resulting from service delays while in performance of the obligations under this
Warranty which are beyond the reasonable control of Dustbane Products Limited or any authorised Dustbane Distributor.
THIS Warranty is expressly in lieu of all other warranties expressed or implied, (including any implied warranty of merchantability
or tness for a particular purpose), and there are no conditions, warranties or representations, whether oral or written except as ex-
pressly stated herein. Neither Dustbane Products Limited, any authorised Dustbane Distributor, any salesman or employees thereof,
nor any other person or individual is authorised to make any statement or representation concerning the obligations of Dustbane
as to the new Equipment unit purchased, nor will Dustbane assume any obligation or liability pursuant to any such statement or
representation except pursuant to this Warranty.
The purchaser upon purchasing any unit of Dustbane Equipment accompanied by this warranty agrees to accept the pro-
tection provided herein and the limitations thereto as being both suffi cient and commercially reasonable.
1999 Dustbane Products Limited
10
3
1
DUSTBANE WARRANTY
Dustbane Products Ltd. www.dustbane.ca
Parts - Pièces
19386
Power Clean 1200 XT-100 Box Extractor / Extracteur à tapis
10
Parts - Pièces
11
Part N. Description Quantity Drawing N.
SN-12-ST-BLU 12 Gallon Solution Tank - Blue 1.00 1
Part of Solution Tank Inserted Molded Into solution tank - 2
S80-0017 Bulk Head Fitting 1.00 3
- Part Of S80-0017 Bulk Head Fitting - 4
S10-0845 1/4” Strainer 1.00 5
SN-12-L-BLU 12 Gal. Lid - Blue 1.00 6
S80-0001 Exhaust Hose 0.40 7
S10-0843 3/8" Black Hose 8.80 8
S10-0826 3/4" Hose Clamp 4.00 9
S80-0026 3/8 Barb x ¼MPT 90º 2.00 10
S10-0806 Barb Hose Fitting 1.00 11
S10-0379 8-32 x 3/8 Screw 8.00 12
S10-0204 Motor Mount Back-Up Washer 18.00 13
S10-0803 Splashproof Switch 3.00 14
S10-0809 3-Hole Switch Plate 1.00 15
S80-0200 Harness 1.00 16
SSN-12-RT-BLU 12 Gal. Rec. Tank - Blue 1.00 17
S80-0008 1.5 PVC Female Adapter 1.00 18
S10-0416-A 1-1/2" Black ABS Stand Pipe 1.30 19
S10-0804-A Hatch Cover Gasket 1.00 20
S10-0804 Hatch Cover 1.00 21
S10-0419-A Screw Hatch 12.00 22
S80-0012 Shut-O Assembly 1.00 23
S10-0805 Dump Valve 1.00 24
S10-0024 1 1/2" Black Vacuum Hose 1.30 25
S10-0849 1-1/2" ABS Fitting 1.00 26
S10-0848-B 1-1/2" 90 Deg. ABS Street Elbow 3.00 27
S10-0833 Motor Manifold Bolts 10.00 28
S10-0204 Motor Mount Back-Up Washer 18.00 29
S10-0811 2-Stage Motor 2.00 30
S10-0838-A Complete Pigtail 1.00 31
S10-0850 Strain Relief 1.00 32
S10-0851 Strain Relief Nut 1.00 33
S10-0822 Exhaust Grate 3.00 34
S10-1030-S2 2-Stage Motor Gasket 2.00 35
SN-12-MFLD Motor Manifold 2.00 36
S10-0830 Hinge Keeper 2.00 37
S10-0821 Hinge 2.00 38
S10-0820 End Cap for Rod 4.00 39
19386
Power Clean 1200 XT-100 Box Extractor / Extracteur à tapis
Parts - Pièces
12
Parts - Pièces
13
Part N. Description Quantity Drawing N.
SN-12-MB-BLKGRAN 12 Gal. Motor Base Blk.Granite 1.00 40
10-0836 19" Axle 1.00 41
10-0807 Wheels 2.00 42
10-0840 Nylon Washer for Axle 8.00 43
10-0835-N Nut for Pump Bolt 4.00 44
10-0834 Pump Flat Washer 10.00 45
10-0808 Caster 2.00 46
10-0816 Caster Bolt 8.00 47
10-0379 8-32 x 3/8 Screw 8.00 48
10-0400-D Latch 1.00 49
80-0026 3/8 Barb x ¼MPT 90º 2.00 50
80-0017 Bulk Head Fitting 1.00 51
10-0823 3/8" Barb x 3/8" Male 2.00 52
10-0812 100psi Pump 1.00 53
10-0835-B Pump Bolt 100psi 4.00 54
10-0400-C Keeper Latch 1.00 55
10-0868 1/4" Female QD 1.00 56
10-0846 1/4" MPT Hex Nipple 1.00 57
10-0832 S/R Strap Bolts 4.00 58
10-0831 S/R Bracket 2.00 59
10-0818 S/R Top of Tank Bolt 2.00 60
10-0023 Shoulder & Waist Belt Washer 4.00 61
Parts - Pièces
19387
Power Clean 1200 XT-500 Box Extractor / Extracteur à tapis
14
Parts - Pièces
15
Part N. Description -Quantity Drawing N.
SN-12-ST-BLU 12 Gallon Solution Tank - Blue 1.00 1
Part of Solution Tank Inserted Molded Into solution tank - 2
S80-0017 Bulk Head Fitting 1.00 3
- Part Of S80-0017 Bulk Head Fitting - 4
S10-0846 1/4” MPT Hex Nipple 1.00 5
S10-0845 1/8” Strainer 2.00 6
S80-0080-UN 500 psi Regulator/Unloader 1.00 7
S80-0026 3/8 Barb x 1/4 MPT 90 Degree 3.00 8
S10-0826 3/4” Hose Clamp 5.00 9
S80-0001 Exhaust Hose 0.40 10
S80-0003-A 1-1/2” Black Lined Gray Hose 2.00 11
S10-0806 1-1/2” Grey Hose Barb Fitting 1.00 12
Bracket Part of S80-0080 Pump 1.00 13
S80-0006 45 Degree Street Elbow 1.00 14
S80-0011 90 Degree Street Elbow 1.00 15
S10-0803 Splash-proof Switch 3.00 16
S80-0059 500 psi Gauge 1.00 17
S80-0013 500 psi Switch Plate 1.00 18
Connector Part of S80-0059 Gauge - 19
SN-12-L-BLU 12-Gallon Lid – Blue 1.00 20
S80-0010 1/4” Brass Tee 2.00 21
S80-0011-2 90 Degree Street Elbow 1.00 22
S80-0004 1/4” x 4” Brass Nipple 1.00 23
S10-0852 1/4” 90 Degree Brass Elbow 3.00 24
S10-0804-A Hatch Cover Gasket 1.00 25
S10-0804 Hatch Cover 1.00 26
S80-0012 Float Assembly 1.00 27
S10-0416-A 1-1/2” Black ABS Stand Pipe 1.30 28
S80-0008 1.5 PVC Female Adapter 1.00 29
SN-12-RT-BLU 12-Gallon Recovery Tank – Blue 1.00 30
S10-0805 Dump Valve 1.00 31
S10-0849 1-1/2” ABS Fitting 1.00 32
S10-0155 Hose Cu Straight 1.00 33
S10-0848-B 1-1/2” 90 Degree ABS Street Elbow 3.00 34
S10-0833 Motor Manifold Bolts 6.00 35
S80-0116 Spacer for Motor Screw 6.00 36
S10-0811 2-Stage Motor 2.00 37
S10-0838-A Complete Pigtail 1.00 38
S10-0850 Strain Relief for Pigtail - Part of S10-0838-A - 39
19387
Power Clean 1200 XT-500 Box Extractor / Extracteur à tapis
Parts - Pièces
16
Parts - Pièces
17
Part N. Description Quantity Drawing N.
S10-0851 Strain Relief Nut for Pigtail - Part of S10-0838-A - 39
S10-0822 Exhaust Grate 3.00 40
S10-1030-S2 2-Stage Motor Gasket 2.00 41
SN-12-MFLD Motor Manifold 2.00 42
S10-0830 Hinge Keeper 2.00 43
S10-0821 Hinge 2.00 44
S10-0820 End Cap for Rod 4.00 45
SN-12-MB-BLU 12-Gallon Motor Base – Blue 1.00 46
S10-0836 19” Axle 1.00 47
S10-0807 Wheels 2.00 48
S10-0834 Pump Flat Washer 18.00 49
S10-0835-N Nut for Pump Bolt 8.00 50
S10-0808 Caster 2.00 51
S10-0816 Caster Bolt 1/4-20 x 1/2 Hex Bolt 12.00 52
S10-0843-COM
1/2” x 54” Clear Hose Pump
(Includes Fittings and Filter)
1.00 53
S80-0040-C
46” of Blue 3000 psi Hose
(Complete with Fittings and Clamps
1.00 54
S80-0044-S 30” Black Hose with Fittings and Clamps 1.00 55
S10-0835-N Nut for Pump Bolt 4.00 56
Hose Fitting Part of S80-0044-S - 57
Hose Fitting Part of S80-0040-C - 58
S80-0015 500 psi Pump Mount Plate 1.00 59
S10-0833 Motor Manifold Bolts 4.00 60
S80-0044-L 67” Black Hose with Fittings and Clamps 1.00 61
Hose Fitting Part of S80-0044-L - 62
Hose Fitting Part of S80-0044-S - 63
S10-0881 1/4” MNPT x 3/8” JIC 90 Degree - Part of S80-0044-S 1.00 64
S80-0016 500 psi Pump 1.00 65
S10-0835-B Pump Bolt 4.00 66
S10-0400-D Keeper for Latch 1.00 67
S10-0832 S/R Strap Bolts 4.00 68
S10-0040 3000 psi Blue Hose - Part of S80-0040-C 6.00 69
S80-0026 3/8” Barb x 1.4” MPT 90 Degree - Part of S80-0040-C 1.00 70
S80-0017 Bulk Head tting 3.00 71
S10-0379 8-32 x 3/8 Screw 8.00 72
S10-0400-C Latch 1.00 73
S10-0868 1/4” Female QD 1.00 74
S10-0831 S/R Bracket 2.00 75
18
FRANÇAIS
19
Sécurité, opération et entretien
Conservez ces instructions. Lisez et suivez tous les avertissements et mises en garde avant d’utiliser
cet extracteur à tapis. Cette unité est conçue pour un usage commercial.
S’il est bien entretenu, cet extracteur à tapis vous donnera de nombreuses années de satisfaction de fonctionnement sans problème.
Toutes les pièces ont été inspectées en suivant des normes de contrôles de qualités rigides avant leur assemblage nal. Avant
l’emballage, votre extracteur à tapis a été de nouveau inspecté pour assurer un assemblage sans défauts.
Cet extracteur à tapis est emballé pour prévenir les dommages en cours d’expédition. Nous recommandons que lors de la livraison,
vous déballiez l’unité et l’inspecter pour tous dommages. Seul un examen visuel révélera des dommages qui ont pu se produire lors
du transport.
Consignes de sécurité importantes
AVERTISSEMENT - Lire toutes les instructions et consignes avant d’utiliser votre 1200XT.
Pour réduire les risques d’incendie, de choc électrique ou de blessure:
• Utilisez uniquement tel que décrit dans ce manuel. Utilisez uniquement les accessoires recommandés par le fabricant.
• Testez tous les prises avec un testeur d’alimentation avant de brancher la machine sur une prise. Branchez le cordon dans
la prise mise à terre la plus proche.
• Ne pas débrancher en tirant sur le cordon, tirez sur la prise. NE TIREZ PAS l’unité par le cordon.
• Éloignez le cordon des surfaces chauées.
• Ne tentez jamais de faire des ajustements ou des réparations pendant que l’appareil est branché.
• NE PAS utiliser si le cordon ou la prise sont endommagés.
• NE PAS utiliser à l’extérieur, dans l’eau stagnante sur les surfaces mouillées.
• Portez une attention particulière lors de l’utilisation de l’appareil à proximité d’enfants.
• Ne ramassez pas de matériaux inammables ou combustibles ou utiliser la machine où ces matériaux peuvent être présents.
• NE PAS laisser la machine à l’extérieur, dans la chaleur ou le froid extrême. Les éléments météorologiques vont endommager
les composants et annuler la garantie.
• Soulevez en utilisant uniquement les poignées appropriées.
• Toujours porter l’équipement de sécurité et des vêtements approprié lorsque vous utilisez la machine.
• Garder toutes les parties du corps, les cheveux et les vêtements amples à distance des ouvertures et des pièces mobiles.
• Redoubler de prudence lors du nettoyage des escaliers. Ne jamais déplacer la machine vers le haut ou descendre les
escaliers avec du liquide dans la machine.
• Utilisez votre bon sens pour vous protéger et protéger les autres contre les blessures lors de l’utilisation de la machine.
•
Instructions visant la mise à la terre:
IMPORTANT : méthode de mise à la terre incorrecte peut entraîner un risque de décharge électrique.
Cette machine doit être mise à la terre.
L’équipement électrique doit être mise à la terre. En cas de dysfonctionnement ou de panne, la mise à la terre fournit au courant
un chemin de moindre résistance qui réduit le risque de choc électrique. Cet extracteur à tapis est pourvu d’un cordon muni d’un
conducteur de terre et d’une che avec broche de terre. La che doit être branchée dans une prise appropriée correctement installée
et mise à terre conformément aux règlements et ordonnances municipaux.
Si la réparation ou le remplacement du cordon ou la che est nécessaire, ne pas connecter le l de terre à une borne de plat. Le l de
mise à la terre est le l avec une isolation et une surface extérieure verte, avec ou sans rayures jaunes.
AVERTISSEMENT: Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique. Consulter
un électricien ou on technicien d’entretien qualié si vous n’êtes pas certain que la prise est correctement mise à
terre. Ne pas modier la che fournie avec l’appareil — si elle ne peut être insérée dans la prise, faire installer une
prise adéquate par un électricien qualie. DESTINÉ À UN CIRCUIT D’ALIMENTATION NOMINAL DE 120 VOLTS: les
extracteurs à tapis sont munis d’une che de mise à terre semblable à celle illustrée par le croquis. S’assurer que
l’appareil est branché à une prise de courant ayant la même conguration que la che. Aucun adaptateur ne
devrait être utilisé avec cet appareil.
FRANÇAIS
20
Installations / Préparation de l’unité pour utilisation
IMPORTANT: Ne pas utiliser sur les surfaces mouillées. Ne pas exposer à la pluie. Entreposer à
l’intérieur.
• Tous les extracteurs à tapis, quelle que soit la période de l’année, sont expédiés avec de l’antigel dans les lignes de solution.
Avant la première utilisation, remplir le réservoir avec un litre d’eau chaude. Fixer le tuyau et en utilisant l’outils à main,
chasser le système en vaporisant la pinte d’eau à travers la pompe.
• Fixez le tuyau d’aspiration de 1-1 / 2 pouces et le laiton déconnexion rapide.
• Remplissez l’unité de base (le réservoir de récupération doit être retiré) avec de l’eau chaude (à moins de 100 degrés
Fahrenheit). Remplir à environ 4 pouces de haut. Pré-vaporiser un détergent liquide fait pour le nettoyage de tapis ou
le rembourrage sur le tapis et agiter tapis. Ensuite, utiliser de l’eau propre du réservoir de solution - cette procédure est
fortement recommandée. Note: lire et mélanger votre solution de pré-vaporisation selon les taux de dilution indiqué.
• Soyez sûr de remplacer les ltres dans l’appareil avant de l’utiliser.
• Ne pas utiliser de l’acide d’agrumes, buterol ou dégraissants forts à l’intérieur de la machine.
Électrique
Branchez le cordon (s) dans une sortie de 20 A mise à la terre. Les circuits de 20 A se trouvent normalement dans les cuisines et salles
de toilettes. Ne jamais retirer la broche de mise à la terre de la prise. Si un disjoncteur se déclenche pendant le fonctionnement,
arrêtez la machine, réarmer le disjoncteur et passer le cordon électrique à une prise diérente et reprendre l’opération.
Aspirateur
L’extracteur utilise un système de moteur double d’aspiration qui fournit une hauteur d’aspiration le ux d’air exceptionnel.
Assemblage du système de otteur de l’aspirateur
Lensemble du otteur sur le tuyau vertical à vide empêche le réservoir de déchets de déborder du tuyau vertical et d’endommager
les moteurs d’aspiration. Le moteur atteingnera un son rapide et aigus pour vous alerter lorsque le réservoir de récupération est
sur le point de déborder. Lorsque cela se produit, fermer immédiatement les interrupteurs de l’aspirateur et vider le réservoir de
déchets.
L’ensemble du otteur possède un ltre pour éviter les peluches et les débris de pénétrer dans le tuyau vertical. Reportez-vous à la
section «Entretien» pour l’enlèvement et le nettoyage approprié.
Il est également nécessaire d’utiliser un anti-mousse pour éliminer l’accumulation de mousse dans le réservoir de
récupération qui pourrait cause la mousse / humidité de pénétrer dans l’aspirateur et contribuer à l’échec hâter des moteurs
d’aspiration.
Si l’humidité entre dans les moteurs d’aspiration, contactez un centre de service autorisé. Pour empêcher l’humidité d’endommager
les moteurs d’aspiration pendant l’entreposage, vider le réservoir de récupération et entreposer avec le couvercle ouvert.
Procécures d’arrêts
• Débrancher le tuyau de solution et tuyau d’aspiration de l’outil de nettoyage.
Appuyez sur la gâchette de la valve pour relâcher la pression dans le tuyau avant de
débrancher le tuyau de solution de l’outil de nettoyage.
• Débranchez le ltre à vue claire en ligne à partir des tuyaux d’aspiration et nettoyer
le ltre au besoin.
• Débranchez le tuyau d’aspiration et une solution exible de la machine.
• S’il reste de l’eau dans le réservoir de solution, utiliser le tuyau d’aspiration court et à
aspirer l’excès d’eau dans le réservoir.
• Débranchez les cordons d’alimentation des prises et de la machine.
• Retirez l’ensemble du otteur du réservoir de récupération et nettoyer le ltre au
besoin. Remplacer l’ensemble du otteur et le couvercle du réservoir.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Dustbane Power Clean 1200 XT - 100 Operations Manual
- Taper
- Operations Manual
- Ce manuel convient également à
dans d''autres langues
- English: Dustbane Power Clean 1200 XT - 100
Documents connexes
-
Dustbane Power Clean Mini Spotter Operations Manual
-
Dustbane Power Clean 900 XT Operations Manual
-
-
Targa XL 12 Mode d'emploi
-
-
-
-
-
-
