DeWalt DCN890 Manuel utilisateur

Marque: DeWalt

Modèle: DCN890

Catégorie: Cloueuse

Taper: Manuel utilisateur

DCN890

Final page size: A5 (148mm x 210mm)

DeWALT

English (original instructions) 4

Français (traduction de la notice d’instructions originale) 19

(



    : 36

Figure B

B 

Figure A

A 

Figure C

C 

Figure D

D 

Figure E

E 

Figure G

G 

Figure F

F 

Figure H

H 

Figure I

I 

Figure J

J 

Figure K

K 

Figure L

L 

Figure M

M 

Figure N

N 

ENGLISH

WARNING: To reduce the risk of injury, read the

instruction manual.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

Congratulations!

You have chosen a

DeWALT

tool. Years of experience, thorough

product development and innovation make

DeWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

DCN890

Voltage V

Type 2

Battery type Li-Ion

Magazine angle 15

Loading capacity up to 33 pins

Length of Nails mm 13–57

Nail Thickness mm 2.6–3.7

Weight (without battery pack) kg 4.2

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

English (original instructions)

CORDLESS CONCRETE NAILER

DCN890

Batteries

Chargers/Charge Times (Minutes)

DCN890

Weight

Batteries Chargers/Charge Times (Minutes)

Cat # V

Weight

DCB107 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 270 140 90 60 90 X

DCB547 18/54 9.0/3.0 1.25 420 220 140 85 140 X

DCB181 18 1.5 0.35 70 35 22 22 22 45

DCB182 18 4.0 0.61 185 100 60 60 60 120

DCB183/B 18 2.0 0.40 90 50 30 30 30 60

DCB184/B 18 5.0 0.62 240 120 75 75 75 150

DCB185 18 1.3 0.35 60 30 22 22 22 X

DCB187 18 3.0 0.48 140 70 45 45 45 90

ENGLISH

Batteries

Chargers/Charge Times (Minutes)

DCN890

Weight

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Battery tool use and care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Nailer Safety Warnings

• Always assume that the tool contains fasteners. Careless

handling of the nailer can result in unexpected firing of

fasteners and personalinjury.

• Do not point the tool towards yourself or anyone

nearby. Unexpected triggering could discharge a fastener

causing aninjury.

• Do not actuate the tool unless the tool is placed firmly

against the workpiece. If the tool is not in contact with

ENGLISH

the workpiece, the fastener may be deflected away from

yourtarget.

• Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the nailer may be accidentally activated if it is

pluggedin.

Additional Nailer Safety Warnings



WARNING: When using any nailer, all safety precautions,

as outlined below, should be followed to avoid the risk

of death or serious injury. Read and understand all

instructions before operating thetool.

• Hold tool by insulated gripping surfaces when

performing an operation where the pin may contact

hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock theoperator.

• Always wear appropriate personal hearing and other

protection during use. Under some conditions and duration

of use, noise from this product may contribute to hearingloss.

• Disconnect battery pack from the tool when not in use. Always

remove battery pack and remove fasteners from magazine

before leaving the area or passing the tool to another

operator. Do not carry tool to another work area in which

changing location involves the use of scaffoldings, stairs,

ladders, and the like, with battery pack connected. Do not

make adjustments, perform maintenance or clear jammed

fasteners while battery is inplace.

• Always use trigger lock-off when tool is not in

immediate use. Using the trigger lock-off will prevent

accidentaldischarge.

• Do not remove, tamper with, or otherwise cause the

tool, trigger or trigger lock-off, to become inoperable. Do

not tape or tie trigger in the on position. Do not remove spring

from contact trip. Make daily inspections for free movement of

trigger. Uncontrolled discharge couldresult.

• Inspect tool before use. Do not operate a tool if any portion

of the tool, trigger, or trigger lock-off is inoperable,

disconnected, altered, or not working properly. Damaged

parts or missing parts should be repaired or replaced before

use. Refer toMaintenance.

• Do not alter or modify the tool in anyway.

• Always assume that the tool containsfasteners.

• Do not point the tool at co-workers or yourself at any

time. No horseplay! Work safe! Respect the tool as a

workingimplement.

• Keep bystanders, children, and visitors away while operating a

power tool. Distractions can cause you to lose control. When

tool is not in use, it should be locked in a safe place, out of the

reach ofchildren.

• Do not overreach. Maintain proper footing and balance at all

times. Loss of balance may cause personal injury.

• Use the tool only for its intended use. Do not discharge

fasteners into open air or any material too hard for

the pin to penetrate. Do not use the body of the tool

or top cap as a hammer. Discharged pin may follow

unexpected path and causeinjury.

• Always keep fingers clear of contact trip to prevent

injury from inadvertent release of thepin.

• Refer to the Maintenance and Repairs sections for

detailed information on the proper maintenance of

thetool.

• Always operate the tool in a clean, lighted area. Be sure

the work surface is clear of any debris and be careful not to

lose footing when working in elevated environments such

asrooftops.

• Fasteners must be driven straight into the material. Do not tilt

the nailer while driving fasteners. Personal injury can result

from ricocheted or jammedpins.

• Keep hands and body parts clear of immediate

workarea.



WARNING: To avoid injury keep hands and body away

from the front discharge area of thetool.

• Do not use tool in the presence of flammable dust, gases

or fumes. This tool produces sparks that can ignite gases or

dust causing an explosion. Driving a pin into another pin may

also cause aspark.

• Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil can

result in impact to the body, especially when nailing into hard

or densematerial.

• Grip tool firmly to maintain control while allowing tool to

recoil away from work surface as fastener isdriven.

• Be aware of material thickness when using nailer. A

protruding pin may causeinjury.

• Do not drive pins blindly into walls, floors or other work

areas. Fasteners driven into live electrical wires, plumbing, or

other types of obstructions can result ininjury.

• Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use tool

while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power

tools may result in serious personalinjury.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your

DeWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

ENGLISH



WARNING: 127V units have to be operated via a fail-safe

isolating transformer with an earth screen between the

primary and secondary winding.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Mains Plug Replacement

(Middle East and Africa)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.



WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

battery pack.

2. Insert the battery pack

10

) into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink repeatedly indicating that the

charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

ENGLISH

To remove the battery pack from the charger, push the

battery release button

11

) on the battery pack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before first use.

Charger Operation

Refer to the indicators below for the charge status of the battery

pack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the charging procedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised service centre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

pack life.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of the charger.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fully charged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in the slots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number and voltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personal injury.

• Charge the battery packs only in

DeWALT

chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek medical

attention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark or flame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

ENGLISH

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre for recycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys, etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knocked over.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a short circuit.

DeWALT

batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests and Criteria.

In most instances, shipping a

DeWALT

battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities,

DeWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100 Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentation requirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicable regulations.

Transporting the FLEXVOLT

Battery

The

DeWALT

FLEXVOLT

battery has two modes: Use and

Transport.

Use Mode: When the FLEXVOLT

battery stands alone or is in

DeWALT

18V product, it will operate as an 18V battery. When

the FLEXVOLT

battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54V battery.

Transport Mode: When the cap is attached to the FLEXVOLT

battery, the battery is in Transport mode. Keep the cap for

shipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

batteries of 36 Wh each.

The Use Wh rating might

indicate 108Wh (1battery implied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not in use.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimal results.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged before

use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual before use.

See Technical Data for charging time.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Example of Use and Transport Label Marking

ENGLISH

Do not expose to water.

Have defective cords replaced immediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indoor use.

Discard the battery pack with due care for the

environment.

Charge

DeWALT

battery packs only with designated

DeWALT

chargers. Charging battery packs other

than the designated

DeWALT

batteries with a

DeWALT

charger may make them burst or lead to

other dangerous situations.

Do not incinerate the battery pack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).

Battery Type

The DCN890 operates on a 18 volt battery pack.

These battery packs may be used: DCB141, DCB142, DCB143,

DCB144, DCB145, DCB181, DCB182, DCB183, DCB183B, DCB184,

DCB184B, DCB185, DCB187, DCB546, DCB547DCB496, DCB497.

Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Concrete nailer

1 Charger(P2 models only)

2 Battery packs(P2 models only)

1 Kitbox(P2 models only)

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Visible radiation. Do not stare into light.

13-57 mm

Length of nails.

2.6–3.7 mm

Nail thickness.

Loading capacity.

15˚

Suitable nail collation angle.

Date Code Position (Fig. B)

The date code

23

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2017 XX XX

Year of Manufacture

Description (Fig. A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Trigger

Trigger lock-off

Speed selection switch

Sequential and Rapidcycle

switch

Contact trip release lever

Contact trip

Removable top stand

Stall release lever

Low battery & jam/stall

indicator lights (x2)

Battery pack

Battery release button

Magazine

Magazine support leg

Magazine release lever

Pusher

Utility hook

Intended Use

Your concrete nailer is intended ONLY for use in driving pins

into structural steel OR concrete base materials OR fastening

wood to concrete. This tool has two operating modes, a

sequential operating mode and a unique rapid sequential

operating mode (RapidCycle). Read the section of the manual

Selecting the Mode before using the tool to make sure you are

selecting the proper mode for yourapplication.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

Your concrete nailer is a professional power tool.

Only

DeWALT

pins recommended by the pin hardware

manufacturer and meeting applicable building code

requirements should be used in this tool.

This tool is intended for use by construction professionals.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

without supervision.

ENGLISH

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Dry Fire Lock Out

The concrete nailer is equipped with a dry fire lockout which

prevents the tool from actuating when the magazine is nearly

empty. When 3 pins remain in the magazine, the tool ceases

to operate. Refer to LoadingtheTool to reload a stick of

collatedpins.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only

DeWALT

battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

10

is fullycharged.

To Install the Battery Pack into the Tool

Handle

1. Align the battery pack

10

with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

11

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Utility Hook (Fig. C)

The

DeWALT

cordless nailers include an integrated utility

hook

16

and can be attached to either side of the tool to

accommodate left- or right-handed users.

If the hook is not desired at all, it can be removed from thetool.

To Remove Utility Hook

1. Remove battery pack from tool.

2. To switch the tool from right- to left-hand usage simply

remove the screw

17

from the opposite side of the tool and

reassemble on the other side.

3. Replace battery pack.



WARNING: Remove pins from magazine before making

any adjustments or servicing this tool. Failure to do so may

result in serious injury.



WARNING: Disconnect battery pack from tool before

making any adjustments, changing accessories, servicing,

or moving the tool. Such preventative safety measures

reduce the risk of starting the toolaccidentally.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping or

falling hazard. Some tools with large battery packs will

stand upright on the battery pack but may be easily

knockedover.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Read the section titled Nailer Safety

Warnings at the beginning of this manual. Always wear

eye and ear protection when operating this tool. Keep the

nailer pointed away from yourself and others. For safe

operation, complete the following procedures and checks

before each use of the nailer.

1. Wear proper eye, hearing and respiratory protection.

2. Remove battery pack from tool.

3. Lock the pusher

15

in the back position and remove all pins

from the magazine.

4. Check for smooth and proper operation of contact trip

and pusher latch. Do not use tool if either assembly is not

functioning properly. NEVER use a tool that has the contact

trip restrained in the up position.

5. NEVER use a tool that has damaged parts.



WARNING: To reduce the risk of personal injury,

disconnect battery pack from tool before performing

maintenance, clearing a jammed pin, leaving work area,

moving tool to another location or handing the tool to

another person.

Proper Hand Position (Fig. D)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

ENGLISH



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle as

shown in Fig. D.

Preparing the Tool (Fig. A)

NOTICE: NEVER spray or in any

other way apply lubricants or

cleaning solvents inside the tool.

This can seriously affect the life and

performance of the tool.

NOTE: The battery pack is not fully

charged out of the carton. Follow instructions outlined (refer to

Charging Operations).

1. Read the Nailer Safety Warnings section of

thismanual.

2. Wear eye and ear protection.

3. Remove battery from tool.

4. Ensure magazine is empty of all fastners.

5. Check for smooth and proper operation of contact trip and

pusher latch

15

. Do not use tool if either assembly is not

functioning properly. NEVER use a tool that has the contact

trip restrained in the actuatedposition.

6. Keep tool pointed away from yourself and others.

7. Insert fully charged battery pack.

Using the Trigger Lock-off (Fig. E)



WARNING: To reduce the risk of serious personal injury,

do not keep trigger depressed when tool is not in use. Keep

the trigger lock-off switch LOCKED (Fig.E) when the tool

is not in use.



WARNING: To reduce the risk of serious personal injury,

lock off trigger, disconnect battery pack from tool and

remove pins from magazine before making adjustments.

Each

DeWALT

nailer is equipped with a trigger lock-off

2

which

when pushed to the right as shown in FigureE, prevents the

tool from firing a pin by locking the trigger and bypassing

power to the motor.

When the trigger lock-off is pressed to the left, the tool will be

fully operational. The trigger lock-off should always be locked off

(Fig.E) whenever any adjustments are made or when tool is not

in immediate use.

NOTICE: Do not store tool with battery pack installed. To

prevent damage to the pack and to ensure best battery

life, store battery packs out of the tool or charger in a cool,

dry location.

Loading the Tool (Fig. F)



WARNING: Keep the tool pointed away from yourself

andothers.



WARNING: Never load pins with the contact trip or

triggeractivated.



WARNING: Always remove battery pack before loading or

unloading pins.



CAUTION: Keep fingers clear of pusher latch track to

prevent injury.



WARNING: The trigger lock-off should always be engaged

whenever any adjustments are made or when tool is not

in use.



WARNING: Fasteners used to install metal connectors

must meet the requirements of the applicable building

codes and must be installed in compliance with code

requirements and metal connector hardware supplier

specifications. Failure to properly install connectors may

result in structural failures.

1. Turn the nailer upside down.

2. Slide the spring-loaded pusher latch

15

to the base of the

magazine to lock it into place.

3. Drop pin strips into the loading slot of the magazine,

making sure the pin heads align correctly with the

slot opening. (Refer to Technical Data to determine

compatiblesize.)

4. Keeping fingers clear of the track, close the magazine by

releasing the pusher latch. Carefully allow the latch to slide

forward and engage the pin strip.

Unloading the Tool



WARNING: The trigger lock-off should always be locked

off whenever any adjustments are made or when tool is

not in use.

1. Remove the battery from your nailer.

2. Slide the spring-loaded pusher latch to the base of the

magazine to lock it into place.

3. Tip the tool up until the fastener strip slides freely out of

themagazine.

4. With battery removed, check the nosepiece to verify there

are no pins remaining.

NOTE: The tool is equipped with a magnet in the nose area

for improved tool performance. When unloading, always verify

that the small sticks of pins are not held to the magnetized

nosepiece.

Speed Setting Summary (Fig. A, G, H)

This nailer is equipped with a speed selection switch

3

to adjust

the tool when driving into different materials.

Speed 1: Softer materials (low strength concrete/cinder block)

Speed 2: Medium hardness materials (High strength concrete)

Speed 3: Hard materials (Structural Steel)

In the event pins are not driving to depth in speed 1, you may

have to switch to speed 2 or 3 for additional driving power.

NOTICE: Driving pins into soft materials at high

speed settings will cause excessive wear to your tool

and may result in early failures.

ENGLISH

Speed Setting Application Typical Pin Length

Fastening Steel/Wood to Low Strength

Concrete/Masonry (<4000 psi)

19-25 mm

Fastening Steel/Wood to High Strength

Concrete (>4000 psi)

19-29 mm

Fastening to structural steel;

2x4 to Concrete

13-57 mm



WARNING: Pins must be driven straight into the material.

Do not tilt nailer while driving fasteners. Refer to Fig.H.

Pin retention values improve when the tool is fired

perpendicular to the material.

The tool can be fired/actuated by pulling the trigger

1

in one

of two modes: sequential mode or RapidCycle mode. Refer

to Selecting the Mode for detailed instructions for firing in

eachmode.

Selecting the Mode (Fig. A, G)

To select standard sequential mode, slide the mode selector

switch

4

to display the single arrow ( ) icon.

To select rapid sequential operating mode (RapidCycle), slide

the mode selector switch

4

to display the double arrow

(  )icon.

NOTE: Battery life in RapidCycle mode will be shorter than

in standard sequential mode. Leaving the tool in standard

sequential will give maximum battery life.

Sequential Mode

The sequential mode is used for intermittent nailing. It offers the

maximum battery life for driving pins.

1. Using the mode selector switch

4

, select the

sequentialmode.

2. Release the trigger lock-off

2

3. Push the contact trip

6

against the work surface.

4. Pull the trigger switch

1

to actuate the tool.

5. Release the trigger and raise the nailer from the

worksurface.

6. Repeat steps 3–5 to actuate the next nail.

RapidCycle Mode

In RapidCycle mode, the motor rotation speed is automatically

restored after driving a pin to allow fast consecutive nailing.

While offering the ability to drive more pins in less time, this

mode quickly depletes the batterycharge.

1. Using the mode selector switch

4

to select the

RapidCyclemode.

2. Release the trigger lock-off

2

3. Push the contact trip

6

against the work surface.

4. Pull the trigger switch

1

to actuate the tool.

5. Release the trigger and raise the nailer from the work

surface. NOTE: The tool motor returns to full speed

automatically without the contact trip

6

beingdepressed.

6. Repeat steps 3–5 to actuate the next nail.

Pin/Fastener Troubleshooting

Properly driven pin Over driven pin

CONCRETE

Pin does not hold in the concrete.

Cause:

- Too hard/high strength

concrete

- Hard or large aggregate

inconcrete

Action:

- Use shorter pin.

- Switch to higher speed setting.

Pin does not drive deep enough.

Cause:

- Pin too long

- Speed setting too low

Action:

- Use shorter pin.

- Switch to higher speed setting.

Pin drives too deep.

Cause:

- Pin too short for application

- Speed setting too high

Action:

- Use longer pin.

- Switch to lower speed setting.

Pin bends.

Cause:

- Pin hit large aggregate on entry

- Too hard/high strength

concrete

- Pit hit rebar just under surface

Action:

- Use shorter pin.

- Make sure nailer is

perpendicular to the work

surface.

- Move 8 cm and tryagain.

ENGLISH

STEEL

Pin does not penetrate the surface.

Cause:

- Speed setting too low

- Material to hard for pin type

Action:

- Increase tool speed setting.

Pin breaks or bends.

Cause:

- Pin too long

- Speed setting too low

- Material to hard for pin type

Action:

- Use shorter pin.

- Switch to higher speed setting.

Pin does not hold in the steel.

Cause:

- Steel base material too thin

Action:

- Use alternative means to secure

base material.

Headlights/LED Indicator (Fig. A)

There are low battery and jam/stall indicator lights

9

located on

the front of the tool on each side of the magazine.

LOW BATTERY

Replace battery with a charged pack.

HOT PACK

Let the battery cool or replace it with a

cool pack.

JAM/STALL CONDITION

Rotate the stall release lever to release.

Refer to Stall Release or Clearing a

Jammed Pin.

HOT TOOL (Both LEDs Flashing)

Let the tool cool down before continuing

use.

or any other

combination.

ERROR

Reset tool by removing and reinserting

battery pack or cycling trigger lock off.

If error code persist, take tool to an

authorized

DeWALT

service center.

Stall Release (Fig. I)

If the nailer is used in harder material where all available energy

in the motor is used to drive a fastener, the tool may stall.

The driver will not complete the drive cycle and the jam/stall

indicator will flash. Rotate the stall release lever

8

on the tool

and the mechanism will release. NOTE: The tool will disable

itself and not reset until the battery pack has been removed

and reinserted. If the driver does not automatically return to

the home position, proceed to Clearing a Jammed Pin. If the

unit continues to stall please review the material and fastener

length to be sure that it is not too rigorous an application. The

nailer could also be overheated and needs time to cool before

further use.

Clearing a Jammed Pin (Fig. A, J)



WARNING: To reduce the risk of serious personal

injury, disconnect battery pack from tool before

making any adjustments, changing accessories,

servicing, or moving the tool. Such preventative safety

measures reduce the risk of starting the tool accidentally.



CAUTION: When removing a jammed pin, DO NOT

orient the nailer with the nose up or with the battery

foot up. Positioning the nailer this way makes the

jammed pin or pieces of the pin more likely to be ingested

into the nailer. If any portion of a pin is ingested into the

tool, the pin should be retrieved by removing the top cap.

If a pin becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions toclear:

1. Remove battery pack from tool and engage trigger lock-off.

2. After laying the tool on its side, slide the spring-loaded

pusher latch

15

to the base of the magazine to lock it into

place and unload pin strip.

3. Rotate the magazine release lever

14

and rotate the

magazine

12

forward.

4. Remove jammed/bent nail, using pliers if necessary. The

contact trip can be removed if necessary. Refer to Contact

Trip Replacement.



CAUTION: If any portion of a pin is ingested into the tool,

the pin should be retrieved by removing the topcap.

5. If the driver is in the down position, rotate the stall release

lever on the top of thenailer.

NOTE: If the driver will not reset after rotating the stall

release lever, manually resetting the blade with a long screw

driver may be necessary.

6. Rotate the magazine back into position under the nose of

the tool and close the magazine release lever.

7. Reinsert battery pack.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed and reinserted.

8. Reinsert pins into magazine (refer to Loading the Tool).

9. Release the pusher latch.

10. Disengage the trigger lock-off when ready to

continuenailing.

NOTE: Should pins jam frequently or the driver continually

fail to reset, have tool serviced by an authorized

DeWALT

servicecentre.

Cold Weather Operation

When operating tools at temperatures below freezing:

ENGLISH

1. Keep tool as warm as possible prior to use.

2. Actuate the tool 10 or 15 times into scrap lumber

beforeusing.

Hot Weather Operation

Tool should operate normally. However, keep tool out of direct

sunlight as excessive heat can deteriorate bumpers and other

rubber parts resulting in increased maintenance.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

DAILY MAINTENANCE CHART

ACTION Clean magazine, pusher, and contact trip

mechanism.

WHY Permits smooth operation of magazine, reduces

wear, and prevents jams.

HOW Blowing off the tool with compressed air is the

most effective way to clean the tool. The use

of oils, lubricants periodically or solvents is not

recommended as they tend to attract debris

and/or damage the plastic parts of the tool.

ACTION Before each use, check to ensure all screws and

fasteners are tight and undamaged.

WHY Prevents jams and premature failure of toolparts.

HOW Tighten loose screws using the appropriate hex

wrench or screwdriver.

Lubrication

NOTICE: NEVER spray or in

any other way apply lubricants

or cleaning solvents inside the

tool. This can seriously affect

the life and performance of

the tool.

DeWALT

tools are properly

lubricated at the factory and are ready for use. However, it is

recommended that, once a year, you take or send the tool to a

certified service centre for a thorough cleaning and inspection.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Contact Trip Replacment (Fig. K)

For some applications, using a different contact trip may

bedesirable.



WARNING: For your own safety, read the tool instruction

manual before using any accessory. Failure to heed

these warnings may result in personal injury and serious

damage to the tool and the accessory. When servicing this

tool, use only identical replacementparts.

To Replace Contact Trip:

1. Push down on the contact trip release lever

2. Pull the contact trip

out of the nose of the tool.

3. Hold down the trip release lever

4. With the contact trip alignment marker facing up, as shown

in Figure K, insert the contact trip fully into thetool nose.

5. Release the lever.

DCN8901 Driver Blade Replacement Kit

(Fig. L, M, N)



WARNING: For your own safety, read the tool instruction

manual before using any accessory. Failure to heed

these warnings may result in serious personal injury and

damage to the tool and the accessory. When servicing this

tool, use only identical replacement parts.

NOTICE: All the mechanical parts of the driver replacment

kit are shown for convenience and verification of inclusion.

To Change a Worn Driver:

1. Using a T-20 Torx, loosen the four screws

18

on either side

of the unit.

2. Remove the four screws and the removable top stand

7

Refer to Figure L.

3. Remove housing end cap

19

. Refer to Figure L.

4. Push up on the rear of the driver

20

until you hear a click,

then push the driver forward while holding it in this position

until it passes the upper bumper assembly

22

5. Remove guide rods

21

. Refer to Figure M.

6. Remove upper bumper assembly.

ENGLISH

7. Lift the rear of driver until at an angle and pull the driver out.

Refer to Figure N.

8. Replace driver and follow steps in reverse to reassemble

9. Ensure new driver slides smoothly through the gun before

full reassembly.

10. Return the driver, guide rods, bumpers, housing end cap,

and removable top stand back onto the unit. It is important

to try the alignment of the driver and the flywheel before

screwing the housing end cap back on to the unit. This

can be done by connecting a battery and pushing then

releasing the nose of the unit against a bench or hard

surface. This will start the motor spinning.

NOTE: When the driver and the flywheel are correctly

aligned, you will hear the motor coast back down from

full speed. If the driver and the flywheel are not correctly

aligned, the motor may not start up, may slow down much

faster than normal along with a loud grinding noise from

the unit. If this happens remove and reseat the driver

making sure the bumpers are seated correctly.



WARNING: Always test the unit by firing 19 mm pins

in Speed 1 into scrap material, to ensure that the tool is

working properly. If tool does not operate properly, contact

a recognized

DeWALT

service centreimmediately.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

household waste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

the tool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed of properly.

ENGLISH

TROUBLESHOOTING GUIDE



WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any

adjustments or removing/installing attachments or accessories. An accidental start-up can causeinjury.

SYMPTOM CAUSE FIX

Motor does not run with contact

trip depressed

Trigger lock in locked position Unlock trigger lock.

Dryfire lock out engaged, blocking contact trip from

traveling fully

Load more pins into magazine.

Tool is stalled, locking the motor from rotating Rotate the stall release lever on the tool and the mechanism will

release. If driver does not return, remove battery and manually push

driver back to home position.

Tool is hot. (Check LED indicator to verify these

conditions.)

Let the tool cool down before continuing use.

Battery is hot. (Check LED indicator to verify these

conditions.)

Let the battery cool or replace it with a cool pack.

Bent contact trip See authorised service centre.

Motor stops running after 5 seconds Normal operation, release contact trip and redepress.

Terminals are dirty or damaged See authorised service centre.

Damaged internal electronics See authorised service centre.

Damaged Trigger See authorised service centre.

Tool does not actuate (motor runs

but will not fire)

Dryfire lock out engaged, blocking contact trip from

traveling fully

Load pins into magazine.

Low battery charge or damaged battery Check charge level if pack shows state-of-charge.

Charge or replace battery pack if necessary.

Jammed nail/drive blade not returned to home

position

Remove battery, clear jammed nail, cycle stall release lever, (push driver

up manually if necessary) reinsert battery pack.

Damaged driver Replace driver with kit.

Jammed internal mechanism See authorised service centre.

Damaged internal electronics See authorised service centre.

Motor starts up but generates a

lot of noise

Jammed pin and driver is stuck in down position Use stall release lever, clear and jammed pins, and return driver

manually if necessary.

Damaged driver Replace driver with kit.

Driver blade continues to get stuck

in down position

Jammed pin and driver is stuck in down position Use stall release lever, clear any jammed pins, and return driver

manually if necessary.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken pins stuck

in the track. Refer to Clearing a Jammed Pin.

Damaged or worn driver Replace driver with kit.

Tool operates but does not drive

fasteners fully

Speed select setting in wrong position. Set speed to appropriate setting.

Tool not firmly applied to workpiece Apply adequate force to tool securing it tightly to workpiece. See

instruction manual.

Material and fastener length If the unit continues to stall (forcing the need to rotate the stall release

lever) choose the appropriate material and fastener length that is not

too rigorous of an application.

Use of incorrect speed If trying to drive longer pins in soft woods, or driving pins into harder

materials using speed 1 - adjust speed setting to position 2.

Damaged or worn driver tip Replace driver with kit.

Damaged actuation mechanism See authorised service centre.

ENGLISH

SYMPTOM CAUSE FIX

Tool operates, but no fastener

is driven

No pins in magazine Load pins in magazine.

Wrong size or angle pins Use only the recommended pins. Refer to Technical Data.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken pins stuck

in the track.

Debris in magazine Clean magazine

Damaged or worn driver Replace driver with kit.

Worn magazine Replace magazine. See authorised service centre.

Damaged pusher spring Replace spring. See authorised service centre.

Jammed nail Wrong size or angle pins Use only the recommended pins Refer to Technical Data.

Magazine not secured after previous jam clear/

inspection

Make sure to magazine is latched properly.

Damaged or worn driver Replace driver.

Material and fastener length If the unit continues to stall (forcing the need to rotate the stall release

lever) choose the appropriate material and fastener length that is not

too rigorous an application.

Debris in nosepiece Clean nose area and watch closely for small pieces of broken pins stuck

in the track.

Damaged pusher spring Replace springs. See authorised service centre.

Dry fire lock out is engaged with only 2–4 pins

remaining in magazine and the user is applying

excessive force to contact trip, overriding the lockout

Load more pins in magazine to disengage dryfire lockout.

Tool is not yet run-in New tools can take 100–500 pins for parts to mesh and wear in

together. Drive shorter pins during this period if experiencing difficulty

fully driving pins.

Use of incorrect speed If trying to drive longer pins in soft materials, or driving pins into harder

materials using speed 1 - adjust speed setting to position 2 or 3.

Worn magazine Replace magazine. See authorised service centre.

Driver blade does not slide

backward and forward smoothly

through its firing path

Driver blade is bent Replace driver.

La page charge ...

DeWalt DCN890 Manuel utilisateur

Marque: DeWalt

Modèle: DCN890

Catégorie: Cloueuse

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCN890 User manual

DeWalt DCN890 Manuel utilisateur

DeWalt DCN890 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents