Dyna-Glo EG10000DGP Mode d'emploi

1

“USER’S MANUAL AND

OPERATING INSTRUCTIONS”

MODEL:

Before the rst use of this heater, please read this USER’S MANUAL

very carefully. This USER’S MANUAL has been designed to instruct

you as to the proper manner in which to assemble, maintain, store,

and most importantly, how to operate the heater in a safe and efcient

manner. Please keep this manual for future reference.

CONSUMER : Retain this manual for future reference.

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 877-447-4768 8:30 a.m. - 4:30 pm CST, Monday - Friday.

or email us at [email protected]

8/1/2018

Heavy Electric Utility Heater

Model: EG

100

00DGP

EG

100

00DGP

2

IMPORTANT INSTRUCTIONS

SAVE THESE INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed

to reduce the risk of re, electric shock, and injury to persons, including the

following:

1. Read all instructions before installing or using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch

hot surfaces. Keep combustible materials, such as furniture, pillows,

bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front

of the heater and keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the heater is left operating and unattended.

4. Always turn off the power of heater when not in use.

5. Do not operate any heater with the heater malfunctions, has been

dropped or damaged in any manner. Return heater to authorized service

facility for examination, electrical or mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and

similar indoor locations. Never locate heater where it may fall into a

bathtub or other water container.

8

. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or re, or damage the heater.

9

.

To prevent a possible re, do not block air intakes or exhaust in any

manner. Do not use on soft surfaces, like a bed, where openings may

become blocked.

1

0

. A heater has hot and arcing or sparking parts inside. Do not use it in areas

where gasoline, paint, or ammable liquids are used or stored.

1

. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause re, electric shock, or

injury to persons.

PET OWNERS WARNING: The health of some small pets including birds are extremely sen-

sitive to the fumes produced during the rst-time use of many appliances. These fumes are not

harmful to humans but we recommended that you do not use your heater around birds and small

pets during its initial use until the manufacturing corrosion coatings burn off.

3

Rating AMPS BTU/hour

ITEM PAGE #

PRECAUTIONS - SAFETY GUIDE ................................................. 3

1. DESCRIPTION .......................................................................... 3

2. SPECIFICATIONS

................................................................. 4

5. INSTALLATION ......................................................................... 5

6. OPERATING INSTRUCTIONS ................................................. 10

7. MAINTENANCE ........................................................................ 11

DESCRIPTION

SPECIFICATIONS

GENERAL SAFETY INFORMATION

CONTENTS OF USER’S MANUAL

This heater requires hardwire installation (no plug). The installation of this

product must be carried out by a certied electrician and in accordance

with all local and national electrical codes.

NOTE: Compatible with a 240V Line Voltage Double Pole Wall Thermostat.

Must be installed by a Certied Electrician.

Read and understand all installation & operation instructions prior to

operating this unit. Observe all safety instructions.

WARNING

1. Use only copper wires rated for at least 60ºC.

2. Heater air ow must be directed parallel to or away from adjacent wall.

3. Observe all wall, oor and ceiling clearance requirements.

4. All wiring must be done according to national and local electrical codes. The

heater must be grounded as a precaution against possible electrical shock.

Heater circuit must be protected with proper fuses.

5. The mounting structure and the anchoring hardware must be capable of

supporting the weight of the heater and the mounting bracket (if used).

..................................................................... 3

3. GENERAL SAFETY INFORMATION ........................................

4

4. LOCATING HEATER

10000

W II 240-1-60

41.66

34100

75

00W I 240-1-60

31.25

22589

This Electric Garage Heater is the ideal heating solution for your garage, warehouse, or

workshop with its 2 heat settings, convenient space-saving ceiling-mount, and adjustable

thermostat.

To ensure safety this heater was designed with overheat protection and a

caution indicator light.

4

GENERAL SAFETY INFORMATION

LOCATING HEATER

Improper installation or failure to follow the procedures outlined in this

instruction manual can result in serious electrical shock.

WARNING

Figure 2

6. All electrical power must be disconnected at the main service box, which

must be locked before connecting, inspecting, cleaning or servicing the

heater. This is an important precaution to prevent serious electric shock.

7. This heater is not suitable for use in hazardous locations containing

explosive

liquids or vapours. This heater has hot or arcing or sparking pads

inside. Do not use it in areas where gasoline, paint or ammable liquids are

used or stored.

8. This heater is not suitable for use in corrosive atmospheres

or chemical

storage areas.

9. This heater must be mounted at least 8 feet off the oor. For specic

clearances, please see next page.

Install heater away from trafc areas, maintaining clearances stated in

Figure 2

(below). The air ow direction should not be restricted (ie. by columns or

machinery). The air ow should

not blow directly at

exposed walls

. When more

than one heater is used in an area, heaters should be installed so that the air

discharge of each heater supports the air flow of the others, to provide best

warm air circulation as shown in Figure 3 (see page 5).

5

Wood Ceiling

LOCATING HEATER

INSTALLATION

Figure 3

HANGING THE HEATER

1. Attach the heating unit to the mounting bracket.

2. Lift the heater up and into the mounting bracket.

3. Align the bracket screws with the keyhole slots in the mounting bracket.

4. If the heater is to be tilted it must be positioned in the keyhole slots - see

gure 5.

5. Tighten the bracket screws with a wrench so the unit is securely suspended

at horizontal or vertical level.

MOUNTING THE BRACKET

Refer to Figures 4a and 4b.

1. Locate a wood stud in the wood ceiling joist. If you cannot locate a wood

stud, you have to install a wood piece on the ceiling as this heater must be

securely fastened.

2. Remove the mounting bracket from the heating unit by loosening bracket

screws with a wrench and slipping the handle off over the screw heads.

3. Place a washer on screws before inserting through the holes in the mounting

bracket and screw them securely into a ceiling joist.

It is suggested to drill a

15/64 size pilot hole.

NOTE: If you want to swivel the heater either to the right or left adding a washer

to both sides of the bracket is recommended. A longer lag bolt may be required to

properly secure the unit. See Figure 4a.

6

MULTIPLE VERTICAL ANGLES

NOTE: For the heater to be tilted

vertically, it must be mounted in bottom

keyhole slots of mounting brackets to

maintain adequate clearance and prevent

possible overheating.

WARNING

To prevent possible electric shock, disconnect power to the heater at the

main service box before attempting to adjust the heat output of this unit.

3. Adjust louvers to the desired position

(see Figure 6)

NOTE: The louvers are designed so they cannot be completely closed. Do not

attempt to defeat this feature; damage to the unit can result.

1. To turn the unit when it has been

installed with a single lag bolt (as

shown in

F

gure 4a), simply turn the

entire heater as needed. The unit

cannot be turned horizontally if it has

been installed with 2 lag bolts.

2. To tilt the unit vertically, loosen the

bracket screws (see

Fi

gure 5).

ADJUSTING AIR FLOW DIRECTION

Figure 5

7

CONNECTING THE POWER

3

4

External thermostat

2

If you will use an external temperature control (external thermostat) to

control the heater, please follow belo

w

diagram

:

1. Make sure that the heater's temperature control knob (thermostat knob) is

turned fully clockwise.

2. Connect the wire according to below wiring diagram.

Selection Switch

(Heater’s thermostat, External thermostat)

Heater’s

thermostat

External

thermostat

8

Warning: This appliance must be grounded!

Warning: The appliance must connect to a current protection circuit or

device at 50Amp or less before being connected to power supply!

WARNING

CAUTION

CONNECTING THE POWER

3. Connect the wire to the power block located in the base of the heater - See Figure 7.

4. Turn on the power at the main service.

TO PROTECT THE HEATING ELEMENT

When starting the heater, turning the temperature control clockwise slowly to

terminal, the unit starts the fan rst then star

ts

the heating element.

When

shutting off t

he heater, turning the temperature control

counter

clockwise

t

o off, the heating element rst

will turn off

then the fan

will run

a short cooling cycle and then turn off.

NOTE: All wiring must be carried out by a Certied Electrician and must be in

accordance to national and local electrical codes in the United States. For certain

applications, conduit may be required, See Figure

7

. Check local electrical codes.

If you run the wiring in conduit and wish to be able to turn the heater be sure to

purchase enough exible conduit to allow the heater to be turned.

1. Remove the screw from the front of the unit to connect the power to the heater.

2. Attach the cable connectors to the unit (See Figure

7

) and slide the 10-gauge

wire through the cable connector.

High temperatures – risk of re. Keep ammable materials, such as

furniture, pillows, bedding, papers, clothes and curtains at least 3 ft. (0.9

m) from the front and top of the heater and keep them away from the

sides and rear. To reduce the risk of re, do not use it in areas where

gasoline, paint or ammable liquids are used or stored.

3. The external temperature control (external thermostat) should be in

accordance with the requirement of UL or

CSA

standard.

4. The lead wire of external temperature control (external thermostat) can not

less than 14AWG.

9

CONNECTING THE POWER

10

The heater must be properly installed before it is used.

WARNING

OPERATING INSTRUCTIONS

NOTE: When the thermal cut-out is activated, the caution indicator will turn red.

In this case, immediately turn the heater OFF and inspect for any objects on or

adjacent to the heater that may cause high temperatures. DO NOT OPERATE

THE HEATER WITH THE CAUTION INDICATOIR GLOWING RED.

ADJUSTING AIR FLOW DIRECTION

1. To turn the unit when it has been installed with a single lag bolt (as shown in

gure 4a), simply turn the entire heater as needed. The unit cannot be turned

horizontally if it has been installed with 2 lag bolts.

2. To tilt the unit vertically, loosen the bracket screws (see

Fi

gure 5

on page 6

).

THERMAL CUT-OUT

The heater will automatically shut off when parts of it overheat. The heater

will turn ON again when the abnormal temperature returns to normal levels.

Should the unit overheat and cause the thermal cut-out to cycle, the cause of

the overheating should be determined and corrective action taken before further

operation.

SETTING THE THERMOSTAT

1) Rotate thermostat knob clockwise to

desired

position, POWER INDICATOR

will turn yellow.

2) After room reaches desired comfort level

the heater will turn off.

Heater will

cycle on and off to maintain room temperature.

SELECTION SWITCH

Using the SELECTION SWITCH, you can control the heating output:

I for

7500W, II for 10000W.

11

MAINTENANCE

Replacement Parts

MAINTENANCE AND CLEANING

1. Before cleaning, make sure the power has been turned off at the circuit

breaker panel and that the heating element of the heater is cool.

2. To maintain the external appearance of the

heater, the unit occasionally needs

to be wiped with

a dry duster. During the summer months, or at other

times when the appliance is not in use and is completely cold,

i

t should be the

wipe

d over with a damp cloth.

3. Do not use abrasive clearing powders or furniture polish. Do not use chemical

or abrasive products, metallic scourers and so on, which may deteriorate the

surface, to clean the appliance.

4. During the summer months, or at other times when the appliance is not in

use, disconnect the power supply, and cover the whole appliance with a

dustcloth. Moreover, keep the appliance in a dry and cool place.

5. All other servicing should be performed by qualied service personnel. Do not

try to repair the heater yourself.

Part Description Part #

1

Back mesh

EG10000DH001AC

2

Mounting bracket

EG10000DH002AC

4 Louvers

EG10000DH004AC

5 Large handle seat

EG5000005AC

6 Small handle seat

EG5000006AC

7

Spring

EG5000007AC

8 Motor

EG10000DH005AC

3 Fan

blade

EG10000DH003AC

Part Description Part #

9 Heater

EG10000DH006AC

10 Selection s

witch

EG5000011AC

11

Thermostat

EG5000012AC

12

Knob

EG5000013AC

13

Terminal block

EG5000014AC

14

Temperature CUT-OFF

EG5000017AC

15

Caution Indicator(Red)

EG5000018AC

16

Power Indicator(Yellow)

EG5000019AC

17 AC Contractor EG7500002AC

12

Warranty

LIMITED WARRANTY:

This limited warranty is extended to the original retail purchaser of this Forced Air/Convection/Radiant Heater and warrants against any defect

in materials and workmanship for a period of one (1) year from the date of retail sale.GHP Group, Inc., at it’s option, will either provide

replacement parts or replace or repair the unit, when properly returned to the retailer where purchased or one of our service centers

as directed by GHP Group,Inc., within one (1) year of retail purchase. (Shipping costs, labour costs,etc. are the responsibility of the purchaser.)

DUTIES OF THE OWNER:

This heating appliance must be operated in accordance with the written instructions furnished with this heater. This warranty shall not excuse

the owner from properly maintaining this heater in accordance with the written instructions furnished with this heater. A bill of sale, canceled

check or payment record must be kept to verify purchase data and establish warranty period. Original carton should be kept in case of

warranty return of unit.

WHAT IS NOT COVERED:

1. Damage resulting from use of improper fuel.

2. Damage caused by misuse or use contrary to the owners manual and safety guidelines.

3. Damage caused by a lack of normal maintenance.

4. Fuses

5. Use of non-standard parts or accessories.

6. Damage caused in transit. Freight charges on warranty parts or heaters to and from the factory shall be the responsibility of the owner.

This warranty does not imply or assume any responsibility for consequential damages that may result from the use, misuse, or the lack of

routine maintenance of this heating appliance. A cleaning fee and the cost of parts may be charged for appliance failures resulting from lack of

maintenance. This warranty does not cover claims which do not involve defective workmanship or materials. FAILURE TO PERFORM

GENERAL MAINTENANCE (INCLUDING CLEANING) WILL VOID THIS WARRANTY.

THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE. THE

REMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES. IN NO EVENT

WILL GHP GROUP, INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not

allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

CLAIMS HANDLED AS FOLLOWS:

1. Contact your retailer and explain the problem.

2. If the retailer is unable to resolve the problem, contact our Customer Service Dept. detailing the heater model, the problem, and proof

of date of purchase.

3. A representative will contact you. DO NOT RETURN THE HEATER TO GHP GROUP, INC. unless instructed by our Representative.

This warranty gives you specic legal rights and you may also have other rights which vary from state to state.

TO REGISTER THE WARRANTY ON YOUR HEATER, PLEASE FILL OUT THIS CARD COMPLETELY

AND MAIL WITHIN 14 DAYS FROM DATE OF PURCHASE OR REGISTER ON-LINE AT www.ghpgroupinc.com

NAME: _______________________________ PHONE: ( ) _________________ EMAIL: ____________________________________

ADDRESS: ___________________________ CITY: ________________________ STATE: _____________________ ZIP: ___________

MODEL: ______________________________ SERIAL#: _____________________ DATE PURCHASED: _________________________

DEALER PURCHASED FROM: _________________________________________ TYPE OF STORE: __________________________

CITY & STATE WHERE PURCHASED: ___________________________________ PRICE PAID: _______________________________

Please Take 1 Minute To Give Us Your Answers To The Following Questions.

All Responses Used Solely For Market Research And Are Held In Strict Condence.

Who primarily decided this purchase?

Male Female 18-24 25-39 40-59 60 and over of age?

Do you own any other portable heaters? Yes No If yes, type ______________________ brand ____________________________

How do you intend to use your new heater? Construction Site Farm Warehouse/Commercial Garage/Outbuilding Other

How did you become aware of this heater? In-Store Display Newspaper Ad Magazine Ad Friend/Relative

TV Commercial Store Salesperson Other ____________________________________________________________________

What made you select this heater? Style Size/Portability Price Package Brand Other __________________________

Do you: Own Rent Would you recommend this heater to a friend? Yes No

Please give us your comments _____________________________________________________________________________________

THANK YOU FOR COMPLETING THIS FORM!

Information will be held condential.

13

WARRANTY REGISTRATION

IMPORTANT: We urge you to ll out your warranty registration card within fourteen (14)

days of date of purchase. You can also register your warranty on the internet at

www.ghpgroupinc.com. Complete the entire serial number. Retain this portion of the card

for your records.

Place

Postage

Stamp

Here

SAVE THIS CARD!

GHP Group, Inc.

6440 W Howard St

Niles, IL 60714-3302

Tel: (877) 447-4768

www.ghpgroupinc.com

GHP Group, Inc.

6440 W Howard St

Niles, IL 60714-3302

14

15

MANUAL DE INSTRUCCIONES

Antes de utilizar por primera vez este calentador, lea este MANUAL DEL

USUARIO atentamente. Este MANUAL DEL USUARIO ha sido diseñado

para instruirle la forma adecuada de ensamblar el calentador, brindarle

mantenimiento, guardarlo y lo más importante: cómo hacerlo funcionar de

manera segura y ecaz. Conserve este manual para referencia futura.

CONSUMIDOR: Conserve este manual para referencia futura.

¿Preguntas, problemas, partes faltantes? Antes de regresar al distribuidor,

llame a nuestro departamento de servicio al 877-447-4768 de 8:30 a.m. a

4:30 p.m. hora estándar del centro, de lunes a viernes o envíenos un correo

electrónico a [email protected].

8/1/2018

Calefactor eléctrico resistente de

uso general Modelo: EG

100

00DGP

MODELO: EG

100

00DGP

16

ADVERTENCIA PARA DUEÑOS DE MASCOTAS: Algunas mascotas pequeñas, incluidos los

pájaros, son muy sensibles a la exposición de los humos que se producen durante el uso de

electrodomésticos por primera vez. Estos humos no son dañinos para los seres humanos, pero

le recomendamos que no utilice el calefactor cerca de pájaros y mascotas pequeñas durante el

primer uso de la unidad hasta que los recubrimientos anticorrosivos se quemen por completo.

INSTRUCCIONES IMPORTANTES

GUARDE ESTAS INSTRUCCIONES.

Al usar electrodomésticos, siempre se deben respetar las precauciones básicas

para reducir el riesgo de incendio, choques eléctricos y lesiones personales,

incluidas las siguientes:

1. Lea todas las instrucciones antes de instalar o usar este calefactor.

2. Este calefactor se calienta cuando está en uso. Para evitar quemaduras,

no toque las supercies calientes con la piel descubierta.

Mantenga los materiales combustibles, como muebles, almohadas, ropa de

cama, papeles, vestimenta, cortinas, etc. a una distancia mínima de 3 pies (0,90

m) de la parte frontal del calefactor, y alejados de los laterales y de la parte

trasera.

3. Se debe tener sumo cuidado al usar calefactores junto a niños o

personas inválidas, o cerca de ellos, y en todo momento en que el

calefactor se deje prendido y desatendido.

4. Siempre desconecte la alimentación al calefactor cuando no esté en uso.

5. No ponga en funcionamiento ningún calefactor después de que haya

fallado. Desconecte la alimentación en el panel de servicio eléctrico

y haga revisar el calefactor por un electricista profesional antes de volver

a utilizarlo.

6. No lo utilice al aire libre.

7. Este calefactor no está diseñado para usarse en baños, lavaderos o

lugares cubiertos similares. No ubique el calefactor en un lugar donde

pueda caerse dentro de una bañera u otro contenedor de agua.

8. No inserte ni permita que ingresen objetos extraños en ninguna abertura

de ventilación o escape porque podrían provocar un choque eléctrico, un

incendio o daños en el calefactor.

9. Para evitar posibles incendios, no bloquee las tomas de aire ni el

conducto de escape de ninguna manera. No haga funcionar el calefactor

sobre supercies blandas, como una cama, donde las aberturas puedan

bloquearse.

10. El calefactor contiene piezas internas que se calientan, forman arcos

eléctricos o generan chispas. No lo use en áreas donde se utilice o se

guarde gasolina, pintura o líquidos inamables.

11. Utilice este calefactor solo como se describe en este manual. Otros

usos no recomendados por el fabricante podrían provocar incendios,

choques eléctricos o lesiones personales.

17

ARTÍCULO PÁGINA

PRECAUCIONES - GUÍA DE SEGURIDAD .................................... 17

1. DESCRIPCIÓN ......................................................................... 17

2. ESPECIFICACIONES ............................................................... 17

3. INFORMACIÓN GENERAL SOBRE SEGURIDAD ................... 17

4. UBICACIÓN DEL CALEFACTOR.............................................. 18

5. INSTALACIÓN ........................................................................... 19

6. INSTRUCCIONES DE USO ...................................................... 24

7. MANTENIMIENTO Y LIMPIEZA ............................................... 25

ESPECIFICACIONES

INFORMACIÓN GENERAL SOBRE SEGURIDAD

CONTENIDO

Este calefactor requiere una instalación cableada ja

(sin enchufe). A la instalación la debe realizar un electricista certicado

y se debe efectuar de conformidad con todos los códigos locales y

nacionales de electricidad. NOTA: Compatible con un termostato de

pared bipolar con tensión de línea de 240 V. Debe ser instalado por un

electricista certicado.

Lea y comprenda todas las instrucciones de instalación y funcionamiento,

y respete todas las instrucciones de seguridad.

ADVERTENCIA

1. Utilice solo cables de cobre calicados para 60°C como mínimo.

2. El ujo de aire del calefactor se debe orientar de modo que quede paralelo a

la pared adyacente o en dirección contraria a ella.

3. Respete los requisitos de espacio libre hacia la pared, el piso y el techo.

4. Todo el cableado se debe realizar de conformidad con los códigos

nacionales y locales de electricidad de Estados Unidos y el calefactor debe

estar conectado a tierra como precaución contra posibles choques eléctricos.

El circuito del calefactor se debe proteger con fusibles apropiados.

5. La estructura de montaje y la tornillería de anclaje deben poder soportar

de modo conable el peso del calefactor y del soporte de montaje, si se lo

utiliza.

Índice Amperios BTU/hora

DESCRIPCIÓN

10000W II 240-1-60 41.66 34100

7500W I 240-1-60 31.25 22589

Este calentador eléctrico de garaje es la solución de calefacción ideal para su garaje,

almacén o taller con sus 2 configuraciones de calor, montaje en el techo práctico y

ahorrador de espacio y termostato ajustable.

18

DISTANCIA

MÍNIMA

A PARED

DISTANCIA

MÍNIMA

A PARED

13 pulg.

VISTA LATERAL

10-⁄ pulg.

24 pulg.

4½ pulg.

¾ pulg.

1¾ pulg.

½ pulg.

7-3/8 pulg.

4½ pulg.

DISTANCIA

MÍNIMA

DESDE LA

DESCARGA A

UN OBJETO

DISTANCIA

MÍNIMA AL

PISO 8 pies

ALTURA MÁXIMA DE MONTAJE DESDE:

Unidad para proporcionar aire vertical = 11 pies

Unidad para proporcionar aire horizontal = 8 pies

Nota: El espacio libre mínimo al techo

cuando no se utilizan los soportes de

montaje es de 1-⁄ pulg.

14 pulg.

12½ pulg.

VISTA FRONTAL

6. Se debe desconectar la alimentación eléctrica y bloquear la caja de

servicio eléctrico antes de inspeccionar el calefactor, limpiarlo o realizarle

mantenimiento. Esta es una precaución para evitar choques eléctricos

graves.

7. Este calefactor no es apropiado para utilizarlo en ubicaciones peligrosas

tal como las dene la Asociación Nacional de Protección contra

Incendios (NFPA, por su sigla en inglés) de Estados Unidos. El calefactor

contiene piezas internas que se calientan, forman arcos eléctricos o generan

chispas. No lo use en áreas donde se utilice o se guarde gasolina, pintura o

líquidos inamables.

8. Este calefactor no es apropiado para utilizarlo en atmósferas corrosivas,

como zonas marinas, invernaderos o áreas de almacenamiento de productos

químicos.

9. Este calefactor debe estar ubicado a 8 pies del piso, como mínimo.

Instale el calefactor fuera de las zonas de tránsito y mantenga los espacios

libres indicados en la gura 2. La dirección del ujo de aire no debe estar

restringida por columnas o máquinas. El ujo de aire solo debe rozar las paredes

y no dirigirse directamente a ellas. Cuando se utiliza más de un calefactor

en un área, los calefactores se deben disponer de modo que la descarga de

aire de cada uno acompañe el ujo de aire de los otros para proporcionar una

circulación óptima de aire caliente, como se indica en la gura 3.

INFORMACIÓN GENERAL SOBRE SEGURIDAD

UBICACIÓN DEL CALEFACTOR

Instalar incorrectamente o no respetar los procedimientos descritos en

este manual de instrucciones puede dar lugar a choques eléctricos

graves.

Figura 2

ADVERTENCIA

19

Techo de madera

MONTAR EL SOPORTE

Consulte las guras 4a y 4b.

1. Localice un montante de madera en la viga del techo de madera. Si no

puede localizarlo, debe instalar una pieza de madera en el techo porque el

calefactor se debe sujetar de forma segura.

2. Retire el soporte de montaje de la unidad calefactora; para esto, aoje los

tornillos del soporte con una llave y deslice la manija por afuera y por encima

de las cabezas de los tornillos.

3. Coloque una arandela en los tornillos antes de insertarlos a través de los

oricios del soporte de montaje y atorníllelos rmemente en la viga del techo.

NOTA: Si desea que el calefactor gire hacia la derecha o hacia la izquierda, se

recomienda agregar una arandela a ambos lados del soporte. Es posible que se

necesite un tirafondo más largo para sujetar la unidad correctamente. Consulte

la gura 4a.

UBICACIÓN DEL CALEFACTOR

INSTALACIÓN

Figura 3

COLGAR EL CALEFACTOR

1) Fije la unidad calefactora al soporte de montaje.

2) Eleve el calefactor y colóquelo en el soporte de montaje.

3) Alinee los tornillos del soporte con las ranuras tipo bocallave del soporte de

montaje.

4) Si se desea que el calefactor esté en posición inclinada, se deben utilizar las

ranuras tipo bocallave para posicionarlo correctamente; consulte la gura 5.

5) Ajuste los tornillos del soporte con una llave para que la unidad quede

suspendida rmemente en el nivel horizontal o vertical.

20

MÚLTIPLES ÁNGULOS VERTICALES

1. Para girar la unidad, cuando esta se ha

instalado con un solo tirafondo

(como se muestra en la gura 4a),

simplemente gire todo el calefactor

según sea necesario. La unidad no se

puede girar en sentido horizontal si se

instaló con 2 tirafondos.

2. Para inclinar la unidad verticalmente,

aoje los tornillos del soporte (consulte

la gura 5).

NOTA: Las rejillas están diseñadas para

que no se puedan cerrar por completo.

No intente hacerlo porque puede dañar la

unidad.

3. Ajuste las rejillas a la posición deseada.

NOTA: Las rejillas están diseñadas para que no se puedan cerrar por completo.

No intente hacerlo porque puede dañar la unidad.

ADVERTENCIA

Para evitar posibles choques eléctricos, desconecte la alimentación al cale-

factor en la caja de servicio eléctrico antes de intentar ajustar la salida de

calor de la unidad.

Figura 5

AJUSTAR LA DIRECCIÓN DEL FLUJO DE AIRE

La page charge ...

Dyna-Glo EG10000DGP Mode d'emploi

Dyna-Glo EG10000DGP Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents