JVC NX-PN7 Manuel utilisateur

COMPACT COMPONENT SYSTEM

SYSTEME DE COMPOSANTS COMPACT

NX-PN7

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

LVT1864-002A

[C]

cover_NX-PN7[C].fm Page 1 Sunday, April 27, 2008 1:59 PM

G-1

Warnings, Cautions and Others

Mises en garde, précautions et indications diverses

The lightning flash with arrowhead

symbol, within an equilateral triangle

is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

Le symbole de l’éclair à l’intérieur d’un

triangle équilatéral est destiné à

alerter l’utilisateur sur la présence

d’une “tension dangereuse” non

isolée dans le boîtier du produit. Cette

tension est suffisante pour provoquer

l’électrocution de personnes.

Le point d’exclamation à l’intérieur

d’un triangle équilatéral est destiné à

alerter l’utilisateur sur la présence

d’opérations d’entretien importantes

au sujet desquelles des

renseignements se trouvent dans le

manuel d’instructions.

CAUTION

The button in any position does not

disconnect the mains line.

Disconnect the mains plug to shut the power off

completely (the STANDBY lamp goes off).

The MAINS plug or an appliance coupler is used

as the disconnect device, the disconnect device

shall remain readily operable.

• When the system is on standby, the STANDBY

lamp lights red.

• When the system is turned on, the STANDBY

lamp goes off.

The power can be remote controlled.

ATTENTION

La touche , dans n’importe quelle position, ne

déconnecte pas le système du secteur.

Déconnectez la fiche de secteur pour mettre

l’appareil complètement hors tension (le témoin

STANDBY s’éteint).

La fiche secteur ou un coupleur est utilisé comme

dispositif de déconnexion de l’appareil, et

l’appareil déconnecté doit être prêt à être utilisé.

• Quand le système est en attente, le témoin

STANDBY est allumé en rouge.

• Quand le système est sous tension, le témoin

STANDBY s’éteint.

L’alimentation peut être télécommandée.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or

moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution,

d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne

pas ouvrir le coffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à

l’humidité.

CAUTION

safety_NX-PN7[C].fm Page 1 Sunday, April 27, 2008 1:59 PM

G-2

Note to CATV system installer:

This reminder is provided to call the CATV

system installer’s attention to Section 820-40 of

the NEC which provides guidelines for proper

grounding and, in particular, specifies that the

cable ground shall be connected to the

grounding system of the building, as close to

the point of cable entry as practical.

For U.S.A.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the

equipment and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Changes or modifications not approved by JVC

could void the user’s authority to operate the

equipment.

CAUTION:

Excessive sound pressure from earphones or

headphones can cause hearing loss.

ATTENTION:

Une pression acoustique excessive des

écouteurs ou du casque d’écoute peut

entraîner une perte auditive.

For Canada/pour le Canada

THIS DIGITAL APPARATUS DOES NOT

EXCEED THE CLASS B LIMITS FOR RADIO

NOISE EMISSIONS FROM DIGITAL

APPARATUS AS SET OUT IN THE

INTERFERENCE-CAUSING

EQUIPMENT STANDARD ENTITLED

“DIGITAL APPARATUS,” ICES-003 OF THE

DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE

LES LIMITES DE BRUITS

RADIOELECTRIQUES APPLICABLES AUX

APPAREILS NUMIRIQUES DE CLASSE B

PRESCRITES DANS LA NORME SUR LE

MATERIEL BROUILLEUR; “APPAREILS

NUMERIQUES”, NMB-003 EDICTEE PAR LE

MINISTRE DES COMMUNICATIONS.

CAUTION

• Do not block the ventilation openings or

holes.

(If the ventilation openings or holes are

blocked by a newspaper or cloth, etc., the

heat may not be able to get out.)

• Do not place any naked flame sources, such

as lighted candles, on the apparatus.

• When discarding batteries, environmental

problems must be considered and local rules

or laws governing the disposal of these

batteries must be followed strictly.

• Do not expose this apparatus to rain,

moisture, dripping or splashing and that no

objects filled with liquids, such as vases, shall

be placed on the apparatus.

ATTENTION

• Ne bloquez pas les orifices ou les trous de

ventilation.

(Si les orifices ou les trous de ventilation sont

bloqués par un journal un tissu, etc., la

chaleur peut ne pas être évacuée

correctement de l’appareil.)

• Ne placez aucune source de flamme nue,

telle qu’une bougie, sur l’appareil.

• Lors de la mise au rebut des piles, veuillez

prendre en considération les problèmes de

l’environnement et suivre strictement les

règles et les lois locales sur la mise au rebut

des piles.

• N’exposez pas cet appareil à la pluie, à

l’humidité, à un égouttement ou à des

éclaboussures et ne placez pas des objets

remplis de liquide, tels qu’un vase, sur

l’appareil.

safety_NX-PN7[C].fm Page 2 Sunday, April 27, 2008 1:59 PM

G-3

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a

stand with a height of 10 cm or more.

Attention: Aération correcte

Pour prévenir tout risque de décharge électrique ou d’incendie et éviter toute détérioration, installez

l’appareil de la manière suivante:

1. Avant: Bien dégagé de tout objet.

2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-

dessous.

3. Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation

correcte puisse se faire en le plaçant sur un support d’au moins dix centimètres de hauteur.

Side

Côté

Front

Face

safety_NX-PN7[C].fm Page 3 Sunday, April 27, 2008 1:59 PM

1

Contents

Introduction................................................. 2

Precautions ................................................................ 2

Getting Started............................................ 3

Connections................................................................ 4

Canceling the Display Demonstration ....................... 5

Basic Operations ......................................... 6

Main Unit ................................................................... 6

Remote Control .......................................................... 8

Playing Back from iPod............................ 11

Connecting iPod Devices ......................................... 12

Operations ................................................................13

Listening to FM/AM Broadcasts ............. 15

Playing Back from Other Equipment ..... 17

Connecting Other Equipment................................... 17

Operations ................................................................17

Setting the Clock and Timer....................18

Setting the Clock ...................................................... 18

Setting the Timer...................................................... 19

Troubleshooting ........................................ 21

Specifications.............................................22

EN_NX-PN7[C].BOOK Page 1 Sunday, April 27, 2008 1:54 PM

2

Introduction

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and

to obtain the best possible performance from the unit.

Precautions

Installation

• Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C.

• Install the unit in a location with adequate ventilation to prevent internal heat buildup inside the

unit.

• Leave sufficient distance between the unit and the TV.

• Keep the unit away from the TV to avoid interference with TV.

Power Sources

• When unplugging the unit from the wall outlet, always pull on the plug, not the AC power cord.

Internal Heat

Others

• Should any metallic object or liquid fall into the unit, unplug the AC power cord and consult your

dealer before operating any further.

• If you are not going to operate the unit for an extended period of time, unplug the AC power cord

from the wall outlet.

If anything goes wrong, unplug the AC power cord and consult your dealer.

DO NOT install the unit in a location near heat sources, or in a place subject to direct

sunlight, excessive dust or vibration.

DO NOT handle the AC power cord with wet hands.

For safety, observe the following carefully:

• Make sure there is good ventilation around the unit. Poor ventilation could overheat

and damage the unit.

• DO NOT block the ventilation openings or holes. If they are blocked by a newspaper

or cloth, etc., the heat may not be able to get out.

DO NOT disassemble the unit since there are no user serviceable parts inside.

EN_NX-PN7[C].BOOK Page 2 Sunday, April 27, 2008 1:54 PM

3

Getting Started

Supplied Accessories

After unpacking, check to be sure that you have

all the following items. The number in

parentheses indicates the quantity of each piece

supplied.

• Remote control (1)

• Lithium coin battery CR2025 (1) (The battery

has been installed when shipped from the

factory.)

• FM antenna (1)

• AM loop antenna (1)

If anything is missing, consult your dealer

immediately.

Prepare the Remote Control

When you use the remote control for the first

time, pull out the insulation sheet.

Replacing the battery in the remote control

Insert the battery into the remote control by

matching the polarity (+ and –) correctly.

• If the range or effectiveness of the remote

control decreases, replace the battery.

CAUTION:

Battery shall not be exposed to excessive heat

such as sunshine, fire or the like.

WARNINGS:

• Store the battery in a place where children

cannot reach. If a child accidentally swallows

the battery, consult a doctor immediately.

• Do not recharge, short, disassemble or heat

the battery or dispose of it in a fire. Doing any

of these things may cause the battery to give

off heat, crack, or start a fire.

• Do not leave the battery with other metallic

materials. Doing this may cause the battery to

give off heat, crack, or start a fire.

• When throwing away or saving the battery,

wrap it in tape and insulate; otherwise, the

battery may start to give off heat, crack, or

start a fire.

• Do not poke the battery with tweezers or

similar tools. Doing this may cause the battery

to give off heat, crack, or start a fire.

• Dispose of battery in the proper manner,

according to federal, state, and local

regulations.

In this manual, operations using the remote

control are mainly explained; however, you

can use the buttons and controls on the unit if

they have the same (or similar) name and

marks.

Insulation sheet

Front side

Lithium coin battery

(product number:

CR2025)

Rear side

CAUTION:

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type.

EN_NX-PN7[C].BOOK Page 3 Sunday, April 27, 2008 1:54 PM

4

Connections

Connecting the Antennas

NOTES:

• Make sure the FM antenna does not touch any other terminals, connecting cords or the AC power

cord. Also, keep the antenna away from metallic parts of the unit, connecting cords, and the AC

power cord. This could cause poor reception.

• Keep the AM loop antenna cable wrapped around the AM loop antenna frame, otherwise the

effectiveness and sensitivity of the AM loop antenna may be reduced.

Do not connect the AC power cord until all other connections have been made.

For better FM reception

Disconnect the supplied FM antenna,

and connect to an outdoor FM antenna

using a 75

Ω wire with coaxial type

connector.

Left side

AM loop antenna (supplied):

Turn it until the best reception is obtained.

FM antenna (supplied):

Extend it so that you can obtain

the best reception.

To connect the AM loop antenna

Outdoor FM antenna (not supplied)

FM 75 Ω COAXIAL terminal

(on the rear panel)

EN_NX-PN7[C].BOOK Page 4 Sunday, April 27, 2008 1:54 PM

5

Connecting the Video Cord to View a Video/Picture from iPod

When viewing a video/picture from your iPod on your TV, use a composite video cord (not

supplied) to connect the VIDEO OUT jack on the unit and the composite video input on your TV.

Connecting the Power Cord

Canceling the Display Demonstration

When you connect the AC power cord for the first time, the display demonstration starts

automatically.

• When you operate the unit, the display demonstration stops temporarily. If no operation is done

for 2 minutes, the unit starts the display demonstration again.

• To activate again, hold down DEMO until “DEMO ON” appears on the display.

• When the ECO mode is activated (P.9), the display demonstration does not function.

Buttons

Function

On the Unit On the remote

Hold down until “DEMO OFF” appears on the display.

Video cord (not supplied)

Right side

To a wall outlet

Plug in the AC power cord

only after all connections are

complete.

Right side

EN_NX-PN7[C].BOOK Page 5 Sunday, April 27, 2008 1:54 PM

6

Basic Operations

Main Unit

Operating on the Main Unit

Buttons Functions

Turns on or off (standby) the power.

Changes the color of the illumination bars. (P.10)

• For DEMO button, see page 5.

Activates Sound Turbo. (P.10)

Changes the source to FM, AM (P.15),

or AUDIO IN (P.17).

Display (P.7)

STANDBY lamp Remote control sensor

Dock A (P.12) Dock B (P.12)

Illumination bars (P.10)

FM

AUDIO IN

AM

EN_NX-PN7[C].BOOK Page 6 Sunday, April 27, 2008 1:54 PM

7

Display Information

• Changes the source to iPod /iPod . (P.13)

• Starts playback and pauses for iPod. (P.13)

• iPod (P.13):

Press: Reverse skip/forward skip

Hold down: Reverse search/forward search

• FM/AM (P.15): Tunes in to a station.

Adjusts the volume level (VOL MIN/VOL 1 to VOL 29/VOL MAX).

Symbols Description

iPod Lights up when an iPod is connected to dock A.

iPod Lights up when an iPod is connected to dock B.

S.TURBO Lights up when Sound Turbo is activated. (P.10)

FM Lights up when FM is selected as the source.

AM Lights up when AM is selected as the source.

TUNED Lights up when a station of sufficient signal strength is tuned in.

ST Lights up when FM stereo broadcast is received.

MONO Lights up when FM monaural reception mode is activated.

A.STBY • Lights up when Auto Standby is activated. (P.10)

• Flashes for about 3 minutes before Auto Standby turns off the unit. (P.10)

1/2/3 • Lights up when the Timer is set. (P.20)

• 1/2/3 icon flashes while the Timer is working.

SLEEP Lights up when the Sleep Timer is activated. (P.10)

Buttons Functions

EN_NX-PN7[C].BOOK Page 7 Sunday, April 27, 2008 1:54 PM

8

Using Headphones

Be sure to turn down the volume before connecting headphones.

• Connecting headphones will deactivate the speakers.

Remote Control

Operating on the Remote Control

Basic operations

Buttons Main functions

Turns on or off (standby) the power.

Right side

Stereo mini plug

Headphones (not supplied)

P.9

P.10

P.14

P.14, P.15

P.10

P.18 – 20

P.10

P.13, P.18, P.20

P.13, P.15, P.16

P.14, P.16 – 20

P.13, P.15, P.16,

P.18 – 20

, P.10

EN_NX-PN7[C].BOOK Page 8 Sunday, April 27, 2008 1:54 PM

9

To dim the display and the illumination bars—DIMMER

You can change the brightness of the display and illumination bars.

To set the ECO mode

Setting the ECO mode allows you to reduce power consumption by turning off the display while on

standby.

• To cancel this function, press ECO/DIMMER again. “ECO OFF” appears for a while then the

clock is shown on the display.

• The battery of the iPod is not charged in ECO mode.

Changes the display information.

• For iPod A/iPod B/AUDIO IN:

•For FM/AM:

• When the unit is turned off:

• Changes the source to iPod /iPod . (P.13)

• Starts playback and pauses for iPod. (P.13)

Changes the source to FM, AM (P.15, P.16), or AUDIO IN (P.17).

Adjusts the volume level (VOL MIN/VOL 1 to VOL 29/VOL MAX).

Drops the volume in a moment.

• To restore the volume, press again, or adjust the volume level.

Press repeatedly while the unit is turned on.

DIM 1: Dims the display and the illumination bars.

DIM 2: Dims the display much more than “DIM 1” and the illumination bars are turned off.

Press while the unit is on standby. “ECO ON” appears on the display for a while.

• The clock is not shown on the display when the unit is on standby.

Buttons Main functions

Source name

Clock

Day of the week

Frequency

Day of the week

Clock

Clock Day of the week

DIM 1

DIM OFF

(Canceled)

DIM 2

EN_NX-PN7[C].BOOK Page 9 Sunday, April 27, 2008 1:54 PM

10

To change the color of the illumination bars

You can change the color of the illumination bars.

• The color is memorized for each source.

• When the source is iPod or iPod , you can set the color of each illumination bar separately:

the bar below the source iPod.

To turn off the unit after a certain period of time—Sleep Timer

• To check the time remaining before the shut-off time, press SLEEP once.

If you press the button repeatedly, you can change the shut-off time.

Turning off the unit automatically—Auto Standby

• To cancel this function, hold down AUTO STBY until “OFF” appears on the display.

• This function does not work when FM or AM is selected as the source.

Emphasize the sound—Sound Turbo

This function emphasizes the sound.

• To cancel this function, press SOUND TURBO again. “OFF” appears on the display.

To adjust the tone

You can adjust the bass and treble level.

Press repeatedly to change the color of the illumination bars.

• You can select one of the nine colors.

Press repeatedly to specify the time (in minutes) as follows:

Hold down until “A STBY” appears on the display.

A.STBY starts flashing after playback stops.

If no operation is done for about 3 minutes while A.STBY flashing, the unit will be

turned off.

Press to activate Sound Turbo.

“S-TURBO” appears for a while and S.TURBO lights up on the display.

1

Select the item you want to adjust.

2

Adjust the bass or treble level (-5 to +5).

10 20

30 60 90

120

OFF

(Canceled)

150

180

TREBLE

BASS

EN_NX-PN7[C].BOOK Page 10 Sunday, April 27, 2008 1:54 PM

11

Playing Back from iPod

You can connect 2 iPod devices to the unit and enjoy sound and video from the iPod.

Compatible iPod Types:

*

Only for still picture.

If the iPod does not play correctly, update your iPod software to the latest version.

• For details about updating your iPod, check on the Apple web site <http://www.apple.com>.

iPod model Audio Video

iPod nano 1GB/2GB/4GB

√

—

iPod nano (2nd Generation) 2GB/4GB/8GB

√

—

iPod nano (3rd Generation) 4GB/8GB

√√

iPod mini 4GB

√

—

iPod mini (2nd Generation) 4GB/ 6GB

√

—

iPod (4th Generation) 20GB/40GB

√

—

iPod photo (4th Generation) 20GB/30GB/40GB/60GB

√√

*

iPod video (5th Generation) 30GB/60GB/80GB

√√

iPod classic 80GB/160GB

√√

iPod touch 8GB/16GB/32GB

√√

iPhone 4GB/8GB/16GB

√√

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

iPhone is a trademark of Apple Inc.

EN_NX-PN7[C].BOOK Page 11 Sunday, April 27, 2008 1:54 PM

12

Connecting iPod Devices

Connect the iPod to dock A or B on the unit.

You can have 2 iPod devices connected at the same time.

• Make sure the unit is on standby when you connect an iPod.

NOTES:

• Be careful not to damage the terminal on the dock when connecting/disconnecting the iPod.

• Close the cover of the dock when you do not connect the iPod to the unit.

About the battery charge of the iPod

The battery of the iPod is always charged through the unit except when the unit is in ECO mode

(see page 9).

• When 2 iPod devices are connected, both batteries are charged at the same time.

• For details of the battery charging, see the instruction manual for iPod.

Dock A

Dock B

Dock adapter (supplied with the

iPod or sold separately)

To detach the dock adapter from the dock:

Pull up the dock adapter with your fingernail or a sharp pointed tool using the slot.

• Be careful not to injure your fingertips or damage the terminal of the dock.

EN_NX-PN7[C].BOOK Page 12 Sunday, April 27, 2008 1:54 PM

13

Operations

For details, refer also to the instruction manual for iPod.

*1

Not available for iPhone and iPod touch.

*2

Not equipped with iPhone and iPod touch.

NOTES:

• Before viewing a video/picture from your iPod on your TV, make the appropriate video setting

on the iPod. For details of the setting, see the instruction manual for iPod.

• For iPhone and iPod touch

Operate the iPod directly in the following cases:

– when operating the home button

– when selecting application icons on the Home screen

– when dragging the slider

Buttons

Functions

Control of

the iPod

On the Unit

On the

remote

Press:

– Selects iPod /iPod as the source and starts

playback.

– Starts playback/pauses.

Hold down

*1

: iPod is in sleep mode.

38, 3, or

8

Press: Forward skip

Hold down: Forward search

x

Press: Reverse skip

Hold down: Reverse search

(Press during playback to back to the beginning of

the track.)

4

—

Goes back to the previous menu/screen.

MENU

*2

—

Selects an item on the menu/screen.

– Press: Selects an item.

– Hold down: Scrolls through a list. To stop

scrolling, press either one of the buttons.

• For iPhone and iPod touch: The buttons work

after starting “Music” or “Videos” by tapping

the corresponding application icon on the Home

screen of the iPod.

• For iPod devices other than above: The buttons

work in the same way as operating the Click

Wheel of the iPod counterclockwise/clockwise.

Click

Wheel

*2

Continued on the next page

EN_NX-PN7[C].BOOK Page 13 Sunday, April 27, 2008 1:54 PM

14

*

Not equipped with iPhone and iPod touch.

NOTES:

• JVC is not responsible for any loss of or damage to iPod that might result from the use of this

product.

• Do not touch or hit the terminals of the dock and of the iPod. It might cause damage to these

terminals.

• When you connect your iPod to the dock, make sure the terminal on the dock is fully inserted into

the iPod.

• Always set the volume to the minimum level when connecting or disconnecting an iPod.

• Sound distortion may occur when playing back audio sources with a high recording level. When

distortion occurs, it is recommended to turn off the equalizer of the iPod. For information on

operating the iPod, see the instruction manual for iPod.

• Do not carry the unit with iPod connected. You might drop it down or it might cause damage to

the connector part.

• Turn off the unit when disconnecting an iPod.

• Remove the iPod from the dock when you do not use it.

• When you cannot operate the connected iPod through the unit or using the remote control, operate

the iPod directly.

• After connecting an iPod, wait until the unit is ready for operation (about 3 seconds).

Buttons

Functions

Control of

the iPod

On the Unit

On the

remote

—

Confirms an item on the menu/screen.

Center

button

*

—

Select the desired shuffle mode.

“SHUFFLE” appears on the display for a

while.

• The shuffle icon lights up on the display/screen

of the iPod.

• To cancel, press again until the shuffle icon

disappears.

• Shuffle play applies to the iPod selected as the

source.

—

Select the desired repeat mode.

“REPEAT” appears on the display for a while.

• The repeat icon lights up on the display/screen

of the iPod.

• To cancel, press again until the repeat icon

disappears.

• Repeat play applies to the iPod selected as the

source.

—

EN_NX-PN7[C].BOOK Page 14 Sunday, April 27, 2008 1:54 PM

15

Listening to FM/AM Broadcasts

Basic Operations

Buttons

Functions

On the Unit On the remote

Selects FM or AM as the source.

When an FM programme is broadcast in stereo, ST (stereo)

lights up on the display (only when the reception is good).

Press: Changes the frequency.

Hold down and release: The unit starts searching for stations

and stops when a station of sufficient signal strength is found.

• To stop searching, press again.

—

Tunes in to a preset station: Press repeatedly to select a preset

station number. (For presetting stations, see page 16.)

—

Changes the FM reception mode: When an FM stereo

broadcast is hard to receive or noisy, press to improve

reception. MONO (monaural) lights up on the display.

Reception will improve though the stereo effect is lost.

• To restore the stereo effect, press again.

FM

AUDIO IN

AM

EN_NX-PN7[C].BOOK Page 15 Sunday, April 27, 2008 1:54 PM

16

Presetting Stations

You can preset 30 FM stations and 15 AM stations.

NOTES:

• When you unplug the AC power cord or if a power failure occurs, the preset stations will be erased

in a few days.

• If you store a new station onto an occupied preset number, the station previously stored on that

number will be erased.

1

Select FM or AM as the source.

2

Tune in to the station you want to preset.

• You can also store the monaural reception mode for FM preset stations if

selected.

3

Activate the preset number entry mode.

“SET” flashes on the display for a few seconds.

• Finish the following operations while the indication is flashing.

4

Select a preset number for the station you want to store.

5

Store the station.

“STORED” appears on the display for a while.

EN_NX-PN7[C].BOOK Page 16 Sunday, April 27, 2008 1:54 PM

La page charge ...

JVC NX-PN7 Manuel utilisateur

Ce manuel convient également à

JVC NX-PN7 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents