Funai U9W34 Manuel utilisateur

Marque: Funai

Modèle: U9W34

Taper: Manuel utilisateur

User Manual

Since this module is not sold to general end users directly, there is no user manual of

module.

For the details about this module, please refer to the specification sheet of module.

This module should be installed in the host device according to the interface specification

(installation procedure).

The following information must be indicated on the host device of this module;

[for FCC]

Contains FCC ID:

2AU3BU9W

This device complies with

art 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

*If it is difficult to describe this statement on the host device due to the size, please describe in

the user’s manual and also either describe on the device packaging or on a removable label

attached on the device.

[for ISED(IC)]

Contains IC:

25625

U9W

The following statements must be described on the user manual of the host device of this

module;

[for FCC]

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines.

To comply with FCC RF exposure compliance requirements, this grant is applicable

to only Mobile Configurations. The antennas used for this transmitter must be

installed to provide a separation distance of at least 20 cm from all persons and

must not be co-located or operating in conjunction with any other antenna or

transmitter.

[for ISED(IC)]

This device contains licence-exempt transmitters/receivers that comply with

Innovation, Science and Economic Development Canada’s license-exempt RSS

standards. Operation is subject to the following two conditions:

(1) This device may not cause interference

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

L’ émetterur/récepteur exempt de licence contenu dans le present appareil est

conforme aus CNR d’Innovation, Science et Développement économique Canada

applicables aux apparerils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

for

indoor

use

only

(5150

5250MHz)

Pour usage

intérieur seulement

(5150

5250MHz)

This equipment complies with ISED radiation exposure limits set forth for an

uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)

Exposure rules. To comply with FCC RF exposure compliance requirements, this

grant is applicable to only Mobile Configurations. The antennas used for this

transmitter must be installed to provide a separation distance of at least 20 cm from

all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées

pour un environnement non contrôlé et respecte les règles d’exposition aux

fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé

et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps

humain (a I’exception des extremites : mains, poignets, pieds et chevilles).

[for FCC]

Compliance with FCC requirement 15.407(c)

Data transmission is always initiated by software, which is the passed down

through the MAC, through the digital and analog baseband, and finally to the RF

chip. Several special packets are initiated by the MAC. These are the only ways the

digital baseband portion will turn on the RF transmitter, which it then turns off at

the end of the packet. Therefore, the transmitter will be on only while one of the

aforementioned packets is being transmitted. In other words, this device

automatically discontinue transmission in case of either absence of information to

transmit or operational failure.

[for ISED(IC)]

Data transmission is always initiated by software, which is the passed down through

the MAC, through the digital and analog baseband, and finally to the RF chip.

Several special packets are initiated by the MAC. These are the only ways the digital

baseband portion will turn on the RF transmitter, which it then turns off at the end of

the packet. Therefore, the transmitter will be on only while one of the

aforementioned packets is being transmitted. In other words, this device

automatically discontinue transmission in case of either absence of information to

transmit or operational failure.

La transmission des données est toujours initiée par le logiciel, puis les données

sont transmises par l'intermédiaire du MAC, par la bande de base numérique et

analogique et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le

MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numérique

active l'émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence,

l'émetteur reste uniquement activé lors de la transmission d'un des paquets

susmentionnés. En d'autres termes, ce dispositif interrompt automatiquement toute

transmission en cas d'absence d'information à transmettre ou de défaillance.

[§15.105 Information to the user]

For a Class B digital device or peripheral, the instructions furnished the user shall

include the following or similar statement, placed in a prominent location in the text

of the manual.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Compliance with KDB996369 D03 OEM Manual

1. List of applicable FCC rules

WiFi 2412-2462MHz FCC Part 15.247 Max output power 15.92dBm

WiFi 5180-5240MHz; 5745-5825MHz FCC Part 15.407 Max output power 13.65dBm

2. Summarize the specific operational use conditions

When use this modular transmitter, please do not change the antenna and antenna

gain, the power setting and country code can not be changed.

The Antenna type is monopole antenna and 2T2R

2400-2483.5MHz Peak Gain: ANT A: 2.55dBi; ANT B: 0.94dBi;

U-NII-1 Band (5150-5250MHz) Peak Gain: ANT A: 1.90dBi; ANT B: 0.8dBi;

U-NII-3 Band (5725-5850MHz) Peak Gain: ANT A: -0.04dBi; ANT B: -3.17dBi.

3. Limited module procedure

Not applicable

4. Trace Antenna designs

Not applicable

5. RF exposure considerations

This modular transmitter should be used in the mobile conditions and 20cm from a

person’s body, the host product manufacture should be put those information in the

end-product manual to the end users. If RF exposure statement and use conditions

are not provided, then the host product manufacture is required to take responsibility

of the module through a change in FCC ID(new application)

6. Antenna

The Antenna type is Planar antenna and 2T2R.

2400-2483.5MHz Peak Gain: ANT A: 2.55dBi; ANT B: 0.94dBi;

U-NII-1 Band (5150-5250MHz) Peak Gain: ANT A: 1.90dBi; ANT B: 0.8dBi;

U-NII-3 Band (5725-5850MHz) Peak Gain: ANT A: -0.04dBi; ANT B: -3.17dBi.

7. Label and compliance information

We Had put the FCCID: 2AU3BU9W34 on the modular transmitter and put the

compliance information in this modular use manual, the host device manufacture

need to provide a physical or e-label stating“ contains FCCID: 2AU3BU9W34” with

their finished product and the compliance information should be attached in the

end-product manual.

8. Information on test modes and additional testing requirement

When this modular transmitter installed in a host product, then can use a 4 pin-USB

extend cable, the 4 pin port connect with the modular and USB port connect with a

test computer which installed the test software “MP tool” then can use the software

control the modular working at test mode, select the transmit mode, channel and

power setting.

9. Additional testing, Part 15 Subpart B disclaimer

The modular transmitter is only FCC authorized for the specific rule parts (FCC Part

15C and FCC Part 15E) listed on the grant, and that the host product manufacture is

responsible for compliance to any other FCC rules that apply to the host not covered

by the modular transmitter grant of certificates

Funai U9W34 Manuel utilisateur

Marque: Funai

Modèle: U9W34

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Funai U9W34 User manual

Funai U9W34 Manuel utilisateur

Funai U9W34 Manuel utilisateur

dans d''autres langues

Autres documents