Omcan RS-CN-0360 Manuel utilisateur

Taper
Manuel utilisateur
Revised - 06/18/2018
Toll Free: 1-800-465-0234
Fax: 905-607-0234
www.omcan.com
Refrigerated Showcase
Model RS-CN-0360
Item 41465
Instruction Manual
2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 6
-------------------------------------------------------------------------- 6
--------------------------------------------------------------------------------------------- 7
------------------------------------------------------------------------------------ 7 - 8
-------------------------------------------------------------------------------- 8 - 9
---------------------------------------------------------------------------- 10 - 12
---------------------------------------------------------------------------- 13
------------------------------------------------------------------------------------------------- 14
---------------------------------------------------------------------------- 15
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Operation
Maintenance
Troubleshooting
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
Model RS-CN-0360
3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
4
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
HANDLING AND INSTALLATION
Handle with care
Unplug from the wall socket before moving. Never tilt
the refrigerator over 45 degrees during handling.
Storage
Always store the refrigerator in a dry place.
5
Safety and Warranty
Sufcient space
To allow for proper air circulation and increased
refrigeration capabilities, the refrigerator must have at
least 4”/10cm of space between wall/ceiling and the
machine.
Proper ventilation
Always place the refrigerator in an area with good
ventilation. For rst time use, set in location and wait
at least 2 hours before plugging into wall socket.
Away from heat source
Never place the refrigerator near any type of heat
source or in direct sunlight, as it reduces refrigeration
capabilities.
No heavy load
Never put heavy items on top of the refrigerator.
No altercations/tampering
Never tamper with or make changes to the
refrigerator. Changes and add-ons should not be
installed to the inside or outside of the refrigerator.
Stable location
Unpack and place the refrigerator on at, solid
ground.
PREPARATION AND POWER SUPPLY
Exclusive power outlet
Power supply should be 110V, single phase AC with
exclusive single phase three pin outlet (125V/15A).
The power outlet must be in close proximity to the
ground.
No shared power outlets
Refrigerator cable should never share the power
outlet with any other appliance, as cable will overheat
and may result in a re.
Protect cables
Extra caution should be used when handling cables,
as broken or damaged cables can cause sparking
and may result in a re.
No water ushing
Never ush the refrigerator surface. This can cause
leakage, which may result in electrical damage or re.
Never store ammables and explosives
No explosives or ammables should be stored in,
or in proximity to, the refrigerator, such as gasoline,
alcohol, and adhesives.
No spray
Never spray ammables such as paint or coating
near the refrigerator. This may cause re or
malfunction.
After power outage
After a power outage or the unplugging of the
refrigerator, wait at least 5 minutes before plugging it
back in.
No medicine
Medicine should not be stored inside of the
refrigerator.
1 YEAR PARTS AND LABOUR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures not
improper use.
Please see www.omcan.com/warranty.html for complete info.
6
Technical Specications
Safety and Warranty
Model RS-CN-0360
Rated Input Power 1260 W
Electrical Heating Element 400 W
Capacity 360 L / 12.7 cu.ft.
Electrical 110V / 60 / 1
Lamp Power 2.8 W x 2 (LED)
Shelf Size 31” x 12” / 780 x 300mm (1pc.)
31” x 14” / 780 x 350mm (1pc.)
Shelf Load Capacity 44.1 lbs. / 20 kgs.
Temperature Range 2-10°C / 35.6-50°F
Max Ambient Temperature / RH <27°C (80.6°F) / 70%
Refrigerant and Injection R404a & 660
Type of Climate 6
Rated Current 11.6A
Foaming Agent XPS
Weight 277 lbs. / 126 kg.
Dimensions 34.5” x 37” x 65” / 876 x 945 x 1656mm
Item Number 41465
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
7
Operation
BEFORE USE
Plug refrigerator into the 110V exclusive socket.
After the refrigerator is running, conrm that air suction/ltration is in working order and that it is sufciently
cold. After checking to make sure the refrigerator is working properly, it may be used.
DIGITAL TEMPERATURE CONTROLLER
FEATURES OF FUNCTION
Small, integrated digital controller, which is applicable to the compressor of 1 Hp. Located behind the front
grill.
Main functions are: Temperature Display/Temperature Control/Manual-Automatic /Light Control/Value
Storing/Self-Testing/Parameter Locking.
FRONT PANEL OPERATION
1. Set temperature: Press button; set temperature will be displayed. Press or button to modify and
store the displayed value. Press button to exit the adjustment and display the cold-room temperature.
2. If no button is pressed within 10 seconds, the cold-room temperature will be displayed.
3. Lighting: Press button to activate light in refrigerator; press again to turn off. Manual start/stop defrost:
Press button and hold for 6 seconds to either defrost or to stop defrost.
4. Refrigeration LED: During refrigeration, the LED is on. When the cold room temperature is constant, the
LED is off. During delay start, the LED ashes.
5. Defrost LED: During defrosting, the LED is on. When it stops defrosting, the LED is off. During the delay of
defrost, the LED ashed.
Maintenance
CABINET CLEANING
The product should be cleaned once a week with the power supply disconnected. When cleaning please use a
mild cleansing agent. Only use a damp cloth.
8
Troubleshooting
Trouble Causes Solutions
Strange noise under the
bottom shelf.
Fan blade broken. Power off and x the blade.
Non-refrigerating in spite of
normal operation.
Unit off. Power on.
Melting process. Stop melting.
Refrigerant leaking. Patch the leak and rell refrigerant.
Unit failure. Call Omcan.
Weak air from air curtain,
and higher cabinet
temperature.
Evaporator blocked by frost. Increase melting frequency.
Inside fan damaged. Replace the fan.
Too low point of temperature
controller.
Adjust the set point.
Vent blocked by storage. Remove the storage.
Normal air curtain, but
higher cabinet temperature.
Insufcient refrigerant. Rell the refrigerant.
Too high set point of temperature
controllers.
Adjust the set point for the
temperature controller.
The wind curtain disturbed by strong
air ow.
Removing the disturbing factors.
Ambient temperature or humidity
beyond standards.
Improve the conditions.
Maintenance
CLEANING THE FILTER
When message “EE4” appears on the display, please clean the lter immediately. If the error message still
appears after cleaning the lter, please contact Omcan.
INSTRUCTIONS FOR CLEANING THE FILTER
1. Remove the four screws from the top of the front grill.
2. Pull out the front grill.
3. Take out the lter.
CHECK FOR LEAKS
Observe all connectors and welding joints for oil stains. This indicates that there is a leak, please call Omcan if
you notice any oil stains.
ALWAYS OBSERVE THE OPERATION OF THE UNIT, IN THE EVENT OF ANY ABNORMAL SOUNDS OR
SMELLS, OR IF THE UNIT BEGINS TO SMOKE, DISCONNECT THE UNIT FROM THE POWER SUPPLY
AND CALL OMCAN.
9
Troubleshooting
Melting water overows. Heating pipe for melting water
damaged.
Replace the heating pipe.
Water level controller failure. Replace the water level controller.
Ambient temperature or humidity
beyond standards.
Improve the conditions.
Normal air curtain, but
periodical uctuation of
cabinet temperature.
Condenser contaminated. Clean the condenser.
Poor venting of the unit. Improve the venting conditions.
Heat protection of compressor failure. Replace the heat protection.
Capillary is blocked by ice. Replace the drying lter.
Temperature controller failure. Replace the temperature controller.
NOTE
Following occurrences are not problems:
The murmur of water is heard when the refrigerator is working. It is a normal occurrence as the coolant is
circulating in the system.
When the weather is damp, condensation might be found on the outside of the refrigerator. It is caused by
high humidity. Simply use cloth to wipe it off.
REFERENCE
Item Number Model Number Description Manufacturer Model Number
41465 RS-CN-0360 Refrigerated Showcase
360 L / 12.71 Cu Ft 110V/60/1 RTS-360L
10
Parts Breakdown
Model RS-CN-0360 41465
11
Parts Breakdown
Model RS-CN-0360 41465
12
Parts Breakdown
Model RS-CN-0360 41465
Item No. Description Position Item No. Description Position Item No. Description Position
60672 Feet for RTS-360L 1 66309 Dry Filter for RTS-360L 32 66338 Cover Support - Plastic Coated for
RTS-360L 63
60561 Castor for RTS-360L 2 66310 Condenser for RTS-360L 33 66339 Air Inlet Cover for RTS-360L 64
66291 Front Board of Base for RTS-360L 3 79327 Stands for Condenser for RTS-360L 34 66340 Wind Screen Strip for RTS-360L 65
66292 Middle Board of Base for RTS-360L 4 66311 Condenser Cover for RTS-360L 35 66341 Glass Deector for RTS-360L 66
66293 Fixed Plate for RTS-360L 5 66312 Top Front Panel for RTS-360L 36 66342 Retaining Plate for Front Base Panel for
RTS-360L 67
79303 Water Reciever for RTS-360L 6 66313 Top LED Light for RTS-360L 37 66343 Front Board for Evaporator for RTS-360L 68
66294 Compressor for RTS-360L 7 66314 Night Curtain for RTS-360L 38 60651 Curtain Hook for RTS-360L 69
79304 Pipe for Evaporated Water for RTS-360L 8 66315 Board Ahead Curtain for RTS-360L 39 66344 Holder for Digital Display for RTS-360L 70
79305 Water Level Detector for RTS-360L 9 66316 Honeycomb Panel for RTS-360L 40 30885 Digital Controller for RTS-360L 71
60117 Wire Clip Holder for RTS-360L 10 66317 Ceiling Board of Cabinet for RTS-360L 41 71514 Switch for RTS-360L 72
60116 Wire Clip Cover for RTS-360L 11 66318 Foam of Top Cover for RTS-360L 42 66345 Right Wind Screen of Evaporator for
RTS-360L 73
60936 Control Box for RTS-360L 12 66319 Transparent Plate for RTS-360L 43 66346 Evaporator Cover for RTS-360L 74
79292 Terminal for RTS-360L 13 66320 Bottom Frame of Light Box for RTS-360L 44 66347 Evaporator for RTS-360L 75
79359 Cover of Junction Box for RTS-360L 14 66321 Left Panel of Light Box for RTS-360L 45 66348 Right Board of Evaporator Cover for
RTS-360L 76
66295 Water Nozzle for RTS-360L 15 66322 Top Frame of Light Box - Plastic Coated
for RTS-360L 46 71521 Left Board of Evaporator Cover for
RTS-360L 77
66296 Tray of Heater for RTS-360L 16 66323 Right Panel of Light Box for RTS-360L 47 66349 Left Wind Screen of Evaporator for
RTS-360L 78
66297 Bracket of Water Receiver for RTS-360L 17 66324 Right Support Pillar of Shelf for RTS-360L 48 66350 Base Foam of Evaporator for RTS-360L 79
66298 Heater for RTS-360L 18 66325 Foam of Right Board for RTS-360L 49 66351 Fan Blade for RTS-360L 80
66299 Platen of Heater for RTS-360L 19 66326 Right Fixed Board of Top Front Panel for
RTS-360L 50 60932 Fan Guard for RTS-360L 81
63459 Hose Fitting for RTS-360L 20 66327 Side Glass for RTS-360L 51 60931 Evaporator Fan Motor for RTS-360L 82
71517 Pipe Clip for RTS-360L 21 66328 LED Strip for RTS-360L 52 66352 Holder for Condenser Motor for
RTS-360L 83
79317 Connection Pipe for RTS-360L 22 60707 LED Clamps for RTS-360L 53 60931 Condenser Fan Motor for RTS-360L 84
66300 Foam of Left Side Board for RTS-360L 23 66329 Ventilated Board for RTS-360L 54 60933 Fan Blade for RTS-360L 85
66301 Side Glass Bar for RTS-360L 24 66330 Upper Shelf for RTS-360L 55 66353 Flat Net Cover for RTS-360L 86
66302 Left Support for Shelf for RTS-360L 25 66331 Price Tag Holder for RTS-360L 56 66354 Air Filter for RTS-360L 87
66303 Connector of Evaporator Base Panel for
RTS-360L 26 66332 Right Support Pillar of Shelf for RTS-360L 57 79354 Cover of Circuit Board Box for RTS-360L 88
66304 Support for Upper Cover of Base for
RTS-360L 27 66333 Left Support Pillar of Shelf for RTS-360L 58 60593 Circuit Board Box for RTS-360L 89
66305 Air Inlet Stand for RTS-360L 28 66334 Bottom Shelf for RTS-360L 59 79356 LED Transformer Holder for RTS-360L 90
66306 Support for Ceiling for RTS-360L 29 66335 Right Support Pillar of Shelf for RTS-360L 60 60552 LED Transformer for RTS-360L 91
66307 Left Fixed Board of Top Front Panel for
RTS-360L 30 66336 Left Support Pillar of Shelf for RTS-360L 61 66355 Front Base Panel for RTS-360L 92
66308 Foam of Back Cover for RTS-360L 31 66337 Bottom Board of Cabinet for RTS-360L 62 79290 Power Cord for RTS-360L 93
13
Electrical Schematics
Model RS-CN-0360 41465
14
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
15
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
www.omcan.com/warrantyregistration.html
or email to: [email protected]
Purchasers Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No
Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour diffusion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 3,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 3,500 productos con origen a nivel mundial.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Omcan RS-CN-0360 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues