Sundance Spas Select® Series® Le manuel du propriétaire

6530-512A Rev. B

SELECT

Constance

®

| Victoria

™

S E R I E S

OWNER’S MANUAL

Attention New Spa Owner!

Congratulations on the purchase of your new Sundance

®

spa! The following is

a list of automated functions and maintenance recommendations for your new

spa. Automated functions have been listed below in an attempt to suppress

any operational concerns you may have during startup and the rst 24-hours of

ownership! Maintenance recommendations are listed in an attempt to stress their

importance in protecting your new spa.

Automated Operations

Approximately two minutes after power is applied to the spa, the rst ltration/

heating cycle turns on pump 1 (Section 9.0, page 29). An automatic ve minute

“blow-out” function also activates pump 2 for a period of ve minutes to ush all

lines. Then, after ve minutes, pump 2 turns off and pump 1 continues to operate

for the duration of the cycle.

Note: This function only occurs during the rst ltration/heating cycle each day.

Maintain Healthy Spa Water

Always maintain your hot tub’s water chemistry within the following parameters:

With CLEARRAY® Without CLEARRAY

pH 7.4-7.6 7.4-7.6

Free chlorine no less than 1.0 ppm 3.0-4.0 ppm

Free Bromine no less than 2.0 ppm 2.0-4.0 ppm

Total Alkalinity 100-150 ppm 100-150 ppm

Calcium Hardness 150-250 ppm 150-250 ppm

IMPORTANT: CLEARRAY® Water Purication System is factory installed. If

the CLEARRAY® system is altered or is not operating efciently then follow

the “without CLEARRAY®” water chemistry parameters as dened by the

Association of Pool and Spa Professionals. CLEARRAY® requires an annual

bulb replacement to properly sanitize your water.

!

TO DECREASE RISK OF INFECTION OR DISEASE! Always

maintain your spa lter as outlined below to ensure healthy spa water.

Refer to pages 38-39 for additional information.

Required Filter Maintenance

Your new hot tub is equipped with an advanced 2-stage MICROCLEAN

®

water

ltration system that provides unsurpassed water quality! To ensure maximum

water quality at all times, you should clean and reuse the larger pleated lter

cartridge every month and replace (throw away) the smaller MICROCLEAN lter

cartridge every 3 months, or earlier as necessary. The smaller MICROCLEAN

lter cartridge is designed to be thrown away! Attempts to reuse this lter

cartridge may result in the re-release of unwanted particles back into the spa.

See pages 38-39 for detailed lter cartridge replacement instructions.

Required Water Maintenance

!

TO DECREASE RISK OF INFECTION OR DISEASE! You should

replace the spa’s water every 3 months. The frequency depends on a number of

variables including frequency of use, number of users, and attention paid to

water quality maintenance. You will know it is time for a change when you cannot

control sudsing and/or you can no longer get the normal feel or sparkle to the

water, even though the key water balance measurements are all within the

proper parameters. See pages 45-46 for additional information.

SELECT SERIES

Table of Contents

1.0 Important Spa Owner Information ............................................ 1

2.0 FCC Notice .................................................................................. 1

3.0 Important Safety Instructions for all Spa Owners .................. 2

3.1 Entrapment Risk .......................................................................... 6

3.2 Hyperthermia ............................................................................... 8

3.3 Important Additional CSA Safety Instructions (Canada Only) ...... 8

3.4 General Electrical Safety Instructions .......................................... 9

4.0 Choosing A Location ................................................................. 9

4.1 Outdoor Location ....................................................................... 10

4.2 Indoor Location .......................................................................... 11

5.0 Power Requirements ............................................................... 12

5.1 North American 60 Hz Power Options ....................................... 12

5.2 Export 50 Hz Power Options...................................................... 13

6.0 Electrical Wiring Instructions ................................................. 13

7.0 Spa Fill Up Procedure .............................................................. 16

8.0 Control Functions .................................................................... 22

8.1 Control Panel ............................................................................. 22

8.2 Victoria Spa Features ................................................................ 23

8.3 Victoria Air Controls Diagram ..................................................... 24

8.4 Victoria Massage/Waterfall Selector Diagram............................ 25

8.5 Constance® Spa Features ........................................................ 26

8.6 Constance Air Controls Diagram................................................ 27

8.7 Constance Massage/Waterfall Selector Diagram ...................... 28

9.0 Operating Instructions ............................................................ 29

9.1 Setting Water Temperature ........................................................ 29

9.2 Activate Jets Pumps .................................................................. 30

9.3 Selecting Desired Massage Action ............................................ 30

9.4 Air Controls ................................................................................ 30

9.5 Multi-Colored LED Light Operation ............................................ 31

9.6 Exterior Lights ............................................................................ 31

9.7 Adjusting Fluidix Nex, Intelli-Jets, Reex and ST Jets ............... 32

9.8 Waterfall Operation .................................................................... 32

9.9 Optional BLUEWAVE® Spa Stereo System .............................. 32

10.0 Automatic Filtration Cycles .................................................... 33

10.1 Standard Filtration/Heating Modes (F0-F3) ............................... 33

10.2 Economy Filtration/Heating Modes (F4-F6) ............................... 33

10.3 Lock Modes (L1-L3) ................................................................... 33

10.4 Selecting The Filtration/Heating Mode ....................................... 33

SELECT SERIES

10.5 Programming the Circulation Pump Filtration Cycle .................. 35

10.6 Programming the CLEARRAY® (Ultraviolet)

Water Purication System .......................................................... 36

11.0 Spa Maintenance...................................................................... 38

11.1 Cleaning The Filter ..................................................................... 38

11.2 Draining And Relling................................................................. 40

11.3 Pillow Care ................................................................................. 41

11.4 Cleaning The Spa Interior .......................................................... 42

11.5 Maintaining the Cover ................................................................ 42

11.6 Maintaining The Synthetic Cabinet ............................................ 43

11.7 Winterizing ................................................................................. 43

11.8 Restarting Your Spa in Cold Weather ........................................ 45

11.9 Top Rail Care And Maintenance ................................................ 45

12.0 Water Quality Maintenance ..................................................... 45

12.1 pH Control .................................................................................. 46

12.2 Sanitizing ................................................................................... 46

12.3 CLEARRAY® Water Purication System ................................... 47

12.4 CLEARRAY® Bulb Replacement and

Quartz Tube Maintenance.......................................................... 47

13.0 Error Conditions/Error Messages .......................................... 50

13.1 Summer Logic ............................................................................ 50

13.2 Overheat Condition .................................................................... 51

13.3 Panel displays SN1 .................................................................... 51

13.4 Panel displays SN2 .................................................................... 51

13.5 Panel displays FL1 or FL2 ......................................................... 51

13.6 Panel displays COL ................................................................... 52

13.7 Panel displays ICE ..................................................................... 52

13.8 Panel displays - - - ..................................................................... 52

13.9 Panel displays blb ...................................................................... 52

14.0 Troubleshooting Procedures .................................................. 52

14.1 None of the Components Operate (e.g. Pump, Light) ............... 52

14.2 Pump Does Not Operate but Light Does ................................... 53

14.3 Poor Jet Action ........................................................................... 53

14.4 Water is Too Hot.........................................................................53

14.5 No Heat ...................................................................................... 53

15.0 North American Circuit Diagram ............................................ 54

16.0 Export Circuit Diagram ............................................................ 55

SELECT SERIES

17.0 Optional BLUEWAVE® Spa Stereo System ...........................56

17.1 Pairing the Remote and Stereo..................................................57

17.2 Audio Settings ............................................................................ 57

17.3 Standard Wireless Remote Control Functions ........................... 59

17.4 Electronic Device Connections and Functions...........................60

17.5 Wireless Remote Battery Replacement Procedure ...................62

17.6 BLUEWAVE® Spa Stereo System Specications .....................63

17.7 Stereo Cautions .........................................................................64

SELECT SERIES

Page 1

SELECT SERIES

1.0 Important Spa Owner Information

Your new Sundance

®

Spa is constructed to the highest standards

and is capable of providing many years of trouble-free use. However,

because heat retentive materials are utilized to insulate the spa for

efficient operation, an uncovered acrylic spa surface and wall fittings

directly exposed to sunlight and high temperatures for an extended

period are subject to permanent damage or discoloration. Damage

caused by exposing the spa to this abuse is not covered under warranty.

We recommend that you always keep the spa full of water when it is

exposed to direct sunlight and that you keep the insulating cover in

place at all times when the spa is not in use. Read and carefully follow

the requirements for your spa’s support base found in Section 4.0 titled,

“Choosing a Location” (Page 9).

We constantly strive to offer the finest spas available, therefore

modifications and enhancements may be made which affect the

specifications, illustrations and/or instructions contained herein.

2.0 FCC Notice

This equipment has been tested and found to comply with the limits for

a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

1. Rearrange or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from the

circuit connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modications not expressly approved by the party

responsible for FCC compliance could void the user’s authority to

operate this equipment.

Page 2

SELECT SERIES

3.0 Important Safety Instructions for all Spa Owners

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY!

This spa was manufactured to meet the standards and specications

outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB

Safety Act). When installing and using this spa, basic safety precautions

should always be followed, including:

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Extreme caution must be exercised to prevent unauthorized access

by children.

• To avoid accidents, ensure that children do not use this spa unless

supervised at all times. Adult supervision is a critical safety factor in

preventing children from drowning.

• Use the straps and clip tie downs to secure the spa cover when not

in use. This will help discourage unsupervised children from entering

the spa. Keep the spa cover secure in high-wind conditions.

• There is no representation that the cover, clip tie-downs, or actual

locks will prevent access to the spa.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Keep hair, loose articles of clothing or hanging jewelry away from

suction ttings, rotating jets or other moving components to avoid

entrapment that could lead to drowning or severe injury.

• Never use the spa unless all suction guards, lter, lter lid, or

skimmer assembly are installed to prevent body and/or hair

entrapment.

• Never operate or use the spa if the lter, lter lid, or skimmer

assembly are broken or any part of the skimmer assembly is missing.

Please contact your dealer or nearest service center for service.

• The suction ttings and suction covers in this spa are sized to match

the specic water ow created by the pump(s). If it is necessary to

replace the suction ttings, suction covers or pump(s), be sure that

the ow rates are compatible and are in compliance with the VGB

Safety Act.

• Never replace a suction tting or suction cover with one rated less

than the ow rate marked on the original suction tting. Using

improper suction ttings or suction covers can create a body or hair

suction entrapment hazard that may lead to drowning or severe

injury.

Page 3

SELECT SERIES

3.

!

DANGER: RISK OF SEVERE INJURY FROM ELECTRIC

SHOCK OR DEATH FROM ELECTROCUTION!

• Install the spa at least 5 feet (1.5m), from all metal surfaces. As an

alternative, a spa may be installed within 5 feet of metal surfaces

if each metal surface is permanently connected (bonded) by a

minimum No. 8 AWG (8.4 mm²) solid copper conductor attached

to the wire connector on the grounding lug, inside the equipment

compartment on the equipment box.

• A grounding wire connector is provided on this unit to connect a

minimum No. 8 AWG (8.4 mm²) solid copper conductor between

this unit and any metal equipment, metal enclosures of electrical

equipment, metal water pipe, or conduit within 5 feet (1.5m) of the

unit.

• Never permit any electrical appliance, such as a light, telephone,

radio, television, etc. within 5 feet (1.5m) of a spa unless such

appliances are built-in by the manufacturer.

• Never bring any electrical appliances into or near the spa.

• Never operate any electrical appliances from inside the spa or when

you are wet.

• The electrical supply for this product must include a suitably rated

switch or circuit breaker to open all ungrounded supply conductors

to comply with section 422-20 of the National Electrical Code/USA,

ANSI/NFPA 70. The disconnecting means must be readily accessible

and visible to the spa occupant but installed at least 5 feet (1.5m),

from the spa.

• The electrical circuit supplied for the hot tub must include a suitable

ground fault circuit interrupter (GFCI) as required by NEC Article

680-42.

4.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Extreme caution must be exercised to prevent diving or jumping

into the spa or slipping and falling, which could result in

unconsciousness, drowning, or serious injury. Remember that wet

surfaces can be very slippery.

• Never stand, walk or sit on the top railing of the spa.

5.

!

WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)

CAUSING SEVERE INJURY, BURNS, WELTS OR DEATH!

• Water temperature in excess of 104°F (40°C) may be injurious to

your health.

• Refer to Section 3.2 Hyperthermia for specic causes and symptoms

of this condition.

• The water in the spa should never exceed 104°F (40°C). Water

temperatures between 100°F (38°C) and 104°F (40°C) are

considered safe for a healthy adult.

Page 4

SELECT SERIES

• Lower water temperatures are recommended for young children

(children are especially sensitive to hot water) and when spa use

may exceed 10 minutes.

• The Consumer Products Safety Commission/USA has stated that the

water temperature in a spa should not exceed 104°F (40°C).

• Always test the spa water temperature before entering the spa.

The user should measure the water temperature with an accurate

thermometer since the tolerance of water temperature-regulating

devices may vary as much as +/- 5°F (2°C).

6.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Since excessive water temperatures have a high potential for

causing fetal damage during the early months of pregnancy, if

pregnant or possibly pregnant, consult your physician before using a

spa.

• Pregnant or possibly pregnant women should limit spa water

temperatures to 100°F (38°C).

• Persons suffering from obesity or a medical history of heart disease,

low or high blood pressure, circulatory system problems, diabetes,

infectious diseases or immune deciency syndromes should consult

a physician before using a spa.

• If you experience breathing difculties in association with using or

operating your spa, discontinue use and consult your physician.

• Persons using medication should consult a physician before using

a spa since some medication may induce drowsiness, while other

medication may affect heart rate, blood pressure, and circulation.

• Persons suffering from any condition requiring medical treatment,

the elderly, or infants should consult with a physician before using a

spa.

• The use of alcohol, drugs, or medication before or during spa use

may lead to unconsciousness with the possibility of drowning.

7.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Prolonged immersion in a spa may be injurious to your health.

• Observe a reasonable time limit when using the spa. Exposures

at higher temperatures can cause high body temperature (over-

heating). Symptoms may include dizziness, nausea, fainting,

drowsiness, and reduced awareness. These effects could possibly

result in drowning or serious injury.

• Never use a spa immediately following strenuous exercise. Enter

and exit the spa slowly. Wet surfaces can be slippery.

Page 5

SELECT SERIES

8.

!

WARNING: TO DECREASE RISK OF INFECTION OR

DISEASE!

• To reduce the risk of contracting a waterborne

illness (e.g. an infec-

tion, bacteria or virus) and/or respiratory ailments

, maintain water

chemistry within the parameters listed on the inside cover of this

manual and consult with a licensed engineer regarding proper venti-

lation if installed indoors or in an enclosed area.

• People with infectious diseases should not use a spa to avoid water

contamination, which could result in spreading infections to others.

• Always shower before and after using your spa. Maintain water

chemistry in accordance with manufacturer’s instructions. Failure

to do so may result in contracting a waterborne

illness (e.g. an

infection, bacteria or virus).

9.

!

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the risk of

contracting a waterborne

illness (e.g. an infection, bacteria or virus)

and/or respiratory ailments

that could be present in the air or water.

Consult a licensed architect or building contractor to determine your

specic needs if installing your hot tub indoors.

10. CAUTION: TO DECREASE RISK OF PRODUCT DAMAGE.

• Maintain water chemistry in accordance with manufacturer’s

instructions.

• Proper chemical maintenance of spa water is necessary to maintain

safe water and prevent possible damage to spa components.

11. WARNING: RISK OF SEVERE INJURY OR DEATH!

The appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience or knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

12. NOTE: This spa is not intended nor designed to be used in a

commercial or public application. The spa buyer shall determine

whether there are any code restrictions on the use or installation

of this spa since local code requirements vary from one locality to

another.

Page 6

SELECT SERIES

Hot Tub Safety Literature

To ensure you have a safe and enjoyable hot tub experience,

learn all you can about hot tub safety and emergency procedures.

Especially useful are the brochures listed below:

• Children Aren’t Waterproof

• Pool and Spa Emergency Procedures For Infants and Children

• Layers of Protection

• The Sensible Way to Enjoy Your Spa or Hot Tub

The Association of Pool and Spa Professionals publishes these

brochures. To acquire a brochure:

• Ask your hot tub dealer (they may have copies)

• Go to http://www.apsp.org

• Conduct your own search on the internet

• Write to the following address:

The Association of Pool and Spa Professionals

2111 Eisenhower Avenue

Alexandria VA 22314

703.838.0083

3.1 Entrapment Risk

The Consumer Products Safety Commission/USA has reported that

users of pools and spas have become entrapped (stuck) to drain and/or

suction ttings causing death, drowning, or serious injury (see diagram

below). This spa was manufactured to meet the standards and specica-

tions outlined in the “Virginia Graeme Baker Pool and Spa Safety Act”

(VGB Safety Act). Entrapment risk can be minimized if proper precau-

tions are taken.

DANGER: RISK OF PERSONAL INJURY OR DEATH!

Never operate the spa if a suction tting, suction cover, lter,

lter lid or skimmer assembly are broken, damaged or missing.

!

NOTE: SUCTION COVERS MUST BE REPLACED EVERY 5 YEARS.

Suction Fittings,

Suction Covers

(locations vary

by models)

Filter, Filter

Lid, Skimmer

Assembly

(location and

style vary by

models)

Page 7

SELECT SERIES

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Hair entrapment: May occur if hair is entangled, knotted or snagged

in a drain suction or skimmer assembly. This has been reported in

persons who when submerge themselves underwater, allowing hair

to come close and/or within the reach of the suction ttings, suction

covers or skimmer assembly.

• Keep hair away from suction ttings, suction covers, lter, lter lid or

skimmer assembly.

• Children are at risk for hair entrapment if swimming under water.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Limb entrapment: May occur when a limb becomes entrapped,

inserted or sucked into a suction or outlet opening.

• Always keep suction ttings, suction covers, lter, lter lid

or skimmer assembly in place when operating to avoid limb

entrapment.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

3.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Body entrapment: May occur when part of the torso becomes

entrapped, inserted or sucked into a suction or outlet opening.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

4.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Evisceration (disembowelment) entrapment: May occur when the

buttocks becomes entrapped, inserted or sucked into a suction or

outlet opening.

• Never sit on suction ttings, suction covers, lter, lter lid or skimmer

assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

5.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Mechanical entrapment: May occur when jewelry, swimsuit, or

hair accessories become entangled, knotted or snagged in a drain

suction or skimmer assembly.

• Never allow your jewelry, swimsuit, or hair accessories to come

close to the suction ttings, suction covers or skimmer assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

Page 8

SELECT SERIES

3.2 Hyperthermia

Prolonged immersion in hot water may induce hyperthermia (over-

heating). The use of alcohol or drugs can greatly increase the risk of fatal

hyperthermia in spas. A description of the causes, symptoms, and effects

of hyperthermia are as follows:

Hyperthermia occurs when the internal temperature of the body reaches

a level several degrees above the normal body temperature of 98.6°F

(37°C). The symptoms of hyperthermia include drowsiness, lethargy

(fatigue), and an increase in the internal temperature of the body (feeling

of being too hot). The effects of hyperthermia include:

• Unawareness of impending hazard;

• Failure to perceive heat;

• Failure to recognize the need to exit spa;

• Physical inability to exit spa;

• Fetal damage in pregnant women; and

• Unconsciousness and DANGER of drowning.

A Warning Sign is provided in your warranty packet. Please install at

a location near your spa, where it is visible to users of the spa. For

additional or replacement Warning Signs please contact your local

Sundance spas dealer and reference item number #6530-082.

3.3 Important Additional CSA Safety Instructions (Canada Only)

When using this electrical equipment, basic safety precautions should

always be followed, including the following:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. A green colored terminal or a terminal marked G, Gr, Ground,

Grounding or the symbol

*

is located inside the supply terminal box

or compartment. To reduce the risk of electric shock, this terminal must

be connected to the grounding means provided in the electric supply

service panel with a continuous copper wire equivalent in size to the

circuit conductors that supply this equipment (*IEC Publication 417,

Symbol 5019).

3. At least two lugs marked “Bonding Lugs” are provided on the external

surface or on the inside of the supply terminal box/compartment. To

reduce the risk of electric shock, connect the local common bonding

grid in the area of the spa to these terminals with an insulated or bare

copper conductor not smaller than No. 6 AWG (10 mm²).

4. All eld-installed metal components such as rails, ladders, drains

or other similar hardware within 10 feet (3m) of the spa shall be

bonded to the equipment grounding buss with copper conductors not

smaller than No. 6 AWG (10 mm²).

5. SAVE THESE INSTRUCTIONS.

Page 9

SELECT SERIES

3.4 General Electrical Safety Instructions

Your new Sundance

®

Spa is equipped with a "state-of-the-art"

equipment system. It contains the most advanced safety and self-

protective equipment in the industry. Nonetheless, this spa must be

installed properly to ensure dependable usage. Please contact your

local Sundance dealer or local building department should you have any

questions regarding your installation.

Proper grounding is extremely important. Sundance spas are equipped

with a current collector system. A pressure wire connector is provided

on the surface of the control box, located outside the equipment door

(Figure B, page 15) to permit connection of a bonding wire between

this point and any ground metal equipment, metal water pipe or conduit

within 5 feet (1.5m) of the spa, or copper clad grounding rod buried

within 5 feet (1.5m) of the spa. Bonding wire must be at least No. 8 AWG

(8.4 mm²) solid copper wire. This is a most important safety assurance

feature.

Before installing your spa, check with your local building department to

ensure installation conforms to local building codes.

4.0 Choosing A Location

IMPORTANT: Because of the combined weight of the spa, water

and users, it is extremely important that the base upon which the

spa rests be smooth, at, level and capable of uniformly supporting

this weight, without shifting or settling, for the entire time the spa is

in place. If the spa is placed on a surface which does not meet these

requirements, damage to the skirt and/or the spa shell may result.

Damage caused by improper support is not covered under warranty.

It is the responsibility of the spa owner to assure the integrity of the

support over time. We recommend a poured, reinforced concrete

slab with a minimum thickness of 4 inches (10 cm). Wood decking

is also acceptable provided it is constructed so that it meets the

requirements outlined above.

WARNING: For spas that are to rest on balconies,

roofs or other platforms not specically tied into main

structural support, consult a professional Structural

Engineer with experience in this type of application.

!

Page 10

SELECT SERIES

The spa must be installed in such a manner as to provide drainage away

from it. Placing the spa in a depression without provisions for proper

drainage could allow rain, overow and other casual water to ood the

equipment and create a wet condition in which it would sit in. For spas

which will be recessed into a oor or deck, install so as to permit access

to the equipment, either from above or below, for servicing. Make certain

that there are no obstructions which would prevent removal of all side

cabinet panels and access to the jets components, especially on the side

with the equipment bay doors.

CAUTION: If the spa is indoors or located in an enclosed area,

proper ventilation should be discussed with an Engineer or authority

competent enough to understand the necessary provisions needed

to vent moist or heated air and air associated with chemical odors

outdoors. When the spa is in use considerable amounts of

moisture will escape potentially causing mold and mildew. This

can cause health risk. Over time, this can damage certain surfaces,

surroundings, and equipment.

4.1 Outdoor Location

In selecting the ideal outdoor location for your spa, we suggest that you

take into consideration the following:

• The proximity to changing area and shelter (especially in regions

subject to cold weather).

• The pathway to and from your spa (this should be free of debris so

that dirt and leaves are not easily tracked into the spa).

• The closeness to trees and shrubbery (remember that leaves and

birds could create extra work in keeping the spa clean).

• A sheltered environment (less wind and weather exposure can result

in lowered operation and maintenance costs).

• The overall enhancement of your environment. It is preferable not to

place the spa under an unguttered roof overhang since run-off water

will shorten the life expectancy of the spa cover.

• For spas that are to rest on balconies, roofs or other platforms not

specically tied into main structural support, consult a professional

Structural Engineer with experience in this type of application.

• In the unlikely event that you should ever need to access or gain

entry to any portion of the spa for servicing, it is highly recommended

that you plan your outdoor installation to provide full access to the

entire spa. Take this into consideration when placing the spa in a

deck or enclosed by a surrounding.

• Consider locating your spa away from any reective surface or glass

to prevent any damage to the synthetic skirt.

• Do not shim the spa. To ensure proper support the spa must sit at

on the intended foundation.

!

Page 11

SELECT SERIES

4.2 Indoor Location

For indoor installations many factors need to be considered before

installing a spa indoors:

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the

risk of contracting a waterborne

illness (e.g. an infection,

bacteria or virus) and/or respiratory ailments

that could be

present in the air or water. Consult a licensed architect or

building contractor to determine your specic needs if

installing your hot tub indoors.

!

• PROPER FOUNDATION: Consult a Structural Engineer when

considering a foundation that will adequately support the spa

the entire time it is in place. Proper support is critical especially if

the spa is to rest on a second story or higher. For spas that are to

rest on balconies, roofs or other platforms not specifically tied into the

main structural support, you should consult a professional Structural

Engineer with experience in this type of application.

• PROPER DRAINAGE: It is extremely important to have in place

measures to sufficiently handle excessive water spillage. Be

sure the flooring in which the spa rests on has adequate drainage

and can handle draining of the entire contents of the spa. Be sure

to make provisions for ceilings or any other structures that may be

below the spas installation. Areas around your spa can become wet

or moist so all flooring and subsequent furniture, walls and adjacent

structures should be able to withstand or resist water and moisture.

• PROPER VENTILATION: Proper ventilation should be discussed

with an Engineer or authority competent enough to understand

the necessary provisions needed to vent moist or heated air and

air associated with chemical odors outdoors. When the spa is in

use considerable amounts of moisture will escape potentially causing

mold and mildew, over time this can damage certain surfaces and or

surroundings.

• SUFFICIENT ACCESS: In the unlikely event that you should ever

need to access or gain entry to any portion of the spa for servicing,

it is highly recommended that you plan your indoor installation to

provide full access to the entire spa.

• WARRANTY: Damage caused by not following these guidelines

or any improper installation not in accordance with local codes or

authorities is not covered under the spas warranty. Please consult

your local state or city building ordinances.

• DO NOT SHIM THE SPA. To ensure proper support the spa must sit

at on the intended foundation.

Page 12

SELECT SERIES

5.0 Power Requirements

Sundance

®

spas are designed to provide optimum

performance and exibility of use when connected to the

maximum electrical service listed. If you prefer, your

qualified technician can perform a minor circuit board

modication to allow your spa to accept an electrical service

other than the factory setting.

Note: Refer to pages 54-55 for circuit board conguration details or

contact your authorized Sundance dealer.

5.1 North American 60 Hz Power Options

North American 2-Pump Models (60 Hz)

240V/40A* 240V/50A** 240V/60A***

Voltage: 240 VAC 240 VAC 240 VAC

# of Wires: 3 3 3

Frequency: 60 Hz 60 Hz 60 Hz

Current Draw: 26A 36A 45A

Circuit Breaker: 40A*, 2-Pole 50A**, 2-Pole 60A***, 2-Pole

* In 40A conguration, the heater will not operate while either jets pump is

running in high speed. Note: pump 2 runs only in high speed.

** In 50A conguration, the heater will not operate while both jets pumps

are running in high speed. Note: pump 2 runs only in high speed. This

is the factory setting.

*** In 60A conguration, the heater will operate while both jets pumps are

running in high speed. Note: pump 2 runs only in high speed.

Page 13

SELECT SERIES

5.2 Export 50 Hz Power Options

Export 2-Pump Models (50 Hz)

230V/20A* 230V/30A** 230V/40A***

Voltage: 230 VAC 230 VAC 230 VAC

# of Wires: 3 3 3

Frequency: 50 Hz 50 Hz 50 Hz

Current Draw: 15A 23A 29A

Circuit Breaker: 20A* 30A** 40A***

* In 20A conguration, the heater will not operate while either jets pump is

running in high speed. This is the factory setting. Note: pump 2 runs

only in high speed.

** In 30A conguration, the heater will not operate while both jets pumps

are running in high speed. Note: pump 2 runs only in high speed.

*** In 40A conguration, the heater will operate while both jets pump are

running in high speed. Note: pump 2 runs only in high speed.

6.0 Electrical Wiring Instructions

IMPORTANT NOTICE: The electrical wiring of this spa

must meet the requirements of the National Electrical

Code (NEC) and any applicable state or local codes.

The electrical circuit must be installed by a qualied

electrician and approved by a local building/electrical inspection

authority.

1. Dedicated 240V Power Models: These spas must be permanently

connected (hard-wired) to the power supply. No plug-in

connections or extension cords are to be used in conjunction

with the operation of these spas. Supplying power to these spas

which is not in accordance with these instructions will void both the

independent testing agency listing and the manufacturer’s warranty.

2. The power supplied to this spa must be a dedicated circuit with no

other appliances or lights sharing the power provided by the circuit.

Page 14

SELECT SERIES

3. To determine the current, voltage and wire size required, refer to

Section 5.0 “Power Requirements” (page 12).

• Wire size must be appropriate per NEC and/or local codes.

• We recommend type THHN wire.

• All wiring must be copper to ensure proper connections. Do not

use aluminum wire.

• When using wire larger than #6 (10 mm²), add a junction box near

the spa and reduce to short lengths of #6 (10 mm²) wire to connect

to the spa.

4. The electrical supply for this product must include a suitably rated

switch or circuit breaker to open all ungrounded supply conductors

to comply with Section 422-20 of the National Electrical Code,

ANSI/NFPA 70. The disconnecting means must be readily

accessible and visible to the hot tub’s occupant but installed at

least 5 feet (1.5m) from the hot tub.

5. The electrical circuit supplied for the spa must include a suitable

ground fault circuit interrupter (GFCI) as required by NEC Article

680-42.

6. To gain access to the spa’s power terminal block, remove the

screws securing the cabinet panel on the side of the spa under the

controls. Then remove the four control box door screws and door

(Figures A-B).

7. Select the power supply inlet you want to use (Figure A, page

15). Feed power cable to control box, then install it through the

large opening provided in the bottom side of the box.

8. Connect wires, color to color, on terminal blocks TB1 and TB3

(Figures C-D, page 16). TIGHTEN SECURELY! All wires must

be hooked up securely or damage could result.

9. Install control box door and screws and reinstall the cabinet

panels.

La page est en cours de chargement...

Sundance Spas Select® Series® Le manuel du propriétaire

Sundance Spas Select® Series® Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents