Amprobe AM-AT3500 Le manuel du propriétaire

AT-3500

Underground Cable/Pipe

Locator System

Users Manual

Mode d’emploiUÊBedienungshandbuchUÊManuale d’UsoUÊManual de usoUÊAnvändarhandbokUÊ

1

English

AT-3500

Underground Cable/Pipe

Locator System

Users Manual

AT3500_Rev001

2

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for 1 year from the date of purchase. This

warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Amprobe’s warranty obligation is limited, at Amprobe’s option, to refund of

the purchase price, free of charge repair, or replacement of a defective product . Resellers are not authorized to extend any

other warranty on Amprobe’s behalf. To obtain service during the warranty period, return the product with proof of purchase

to an authorized Amprobe Test Tools Service Center or to an Amprobe dealer or distributor. See Repair Section for details. This

warranty is your only remedy . All other warranties - whether express, implied or statutory - including implied warranties of

ﬁtness for a particular purpose or merchantability, are hereby excluded. Neither Amprobe nor its parent company or afﬁliates

shall be liable for any special, indirect, incidental or consequential damages or losses, arising from any cause or theory. Since

some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or for calibration should be accompanied by the following: your

name, company’s name, address, telephone number, and proof of purchase. Additionally, please include a brief description of

the problem or the service requested and include the test leads with the meter. Non-warranty repair or replacement charges

should be remitted in the form of a check, a money order, credit card with expiration date, or a purchase order made payable to

Amprobe® Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During the warranty period any defective

test tool can be returned to your Amprobe® Test Tools distributor for an exchange for the same or like product. Please check the

“Where to Buy” section on www.amprobe.com for a list of distributors near you. Additionally, in the United States and Canada

In-Warranty repair and replacement units can also be sent to a Amprobe® Test Tools Service Center (see below for address).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be sent to a Amprobe® Test Tools Service Center. Call Amprobe®

Test Tools or inquire at your point of purchase for current repair and replacement rates.

In USA In Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 888-993-5853 Tel: 905-890-7600

Fax: 425-446-6390 Fax: 905-890-6866

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe® Test Tools distributor for a nominal charge. Please check the

“Where to Buy” section on www.amprobe.com for a list of distributors near you.

European Correspondence Address*

Amprobe® Test Tools Europe

Beha-Amprobe GmbH

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 – 0

*(Correspondence only – no repair or replacement available from this address. European customers please contact your

distributor.)

3

1

2

3

4

5

Control Panel with display

Speaker with Volume control

 Headphone jack (3.5 mm headphone not included)

Battery Compartment

Floor Cap (Removable)

Quieter Louder

Light Sensor: Automatically regulates the brightness of

the display

ON/OFF Switch

 Display: Provides visual indication of the signal

strength, depth measurement, and mode of operation,

Battery Status, and menu items.

Control1

Control2

Control3

Battery status indicator: Battery status LED blinks in

red when near empty

ON/OFF Button

 Signal Type: To switch between continuous and pulsed

signal output

Input Jacks

Mode: To switch between inductive and direct signal

coupling

Signal Strength: To select one of two signal strength

levels (0.1W or 0.5W)

+

123

1

2

3

456

R-3500 Receiver

R-3500 Display

T-3500 Transmitter

4

AT-3500

Underground Cable/Pipe Locator System

CONTENTS

Unpacking And Inspection ........................................................................................................................................................................ 5

Introduction................................................................................................................................................................................................ 5

Operation ................................................................................................................................................................................................... 5

Applications and principles of direct coupling......................................................................................................................................... 6

Direct Coupling..................................................................................................................................................................................... 7

Direct Coupling using the A-3500 Clamp............................................................................................................................................ 7

Inductive Coupling................................................................................................................................................................................ 7

Locating Passive Lines (Radio and Power Modes)............................................................................................................................... 7

Locating unknown cables..................................................................................................................................................................... 7

Depth Measurement............................................................................................................................................................................. 7

Error messages during a depth measurement ......................................................................................................................................... 8

Technical Speciﬁcations ............................................................................................................................................................................. 8

Maintenance............................................................................................................................................................................................... 9

Changing the battery in the R-3500 receiver...................................................................................................................................... 9

Changing the batteries in the T-3500 transmitter............................................................................................................................ 10

Changing the ﬂoor cap on the R-3500 receiver................................................................................................................................ 10

5

UNPACKING AND INSPECTION

Your shipping carton should include:

1 R-3500 Receiver

1 T-3500 Transmitter

2 Measurement Cables

2 Alligator Clips

1 Grounding Rod

10 Battery IEC R6/AA Cell /Migon

6 IEC R20/ D Cell/ Mono

1 Nylon Bag

INTRODUCTION

The AT-3500 underground cable/pipe locator system is designed for the uncomplicated and user-friendly determination of the

location, orientation and depth of metallic lines (e.g. cable and pipe lines).

It can be used to probe areas for unknown lines or for locating speciﬁc lines.

The AT-3500 is distinguished by the following features:

Robust construction for use in poor weather and in harsh environments

Simple, user-friendly operation concept with a minimum number of controls

Reliable battery status indicator

OPERATION

Decide which mode of operation to use for your application1.

Induction:UÊ Transmitter’s signal is emitted through the integrated antenna and is thereby inductively coupled with

any metallic lines located within a certain radius.

Place the T-3500 transmitter on the site to be searched. Refer to Figs.1, 2.3&4.i.

Direct Connection:UÊ Transmitter’s signal is directly coupled with a metallic line via the measurement cable which is

connected to the jacks on the front panel of the transmitter. Transmitter clamps, alligator clips or power socket adapters

(for example) may be used to connect the measurement cable to the lines.

Connect the T-3500 transmitter to the line to be located using the desired method. Refer to Figs 1, 2, 3, & 4i.

T-3500 Transmitter

Push and Hold 2. ON/OFF button to switch on the T-4000

Push3. Mode: C to select direct coupling or inductive coupling

Direct coupling UÊ

Green LED blinking: good (low-resistance) connection

Alternating red and green LED blinking: sufﬁcient connection

Red LED blinking: poor/no (high-resistance) connection

Inductive Coupling: UÊ

Green LED blinking: induction mode is active

Push4. Signal Type: M to select Pulsed or Continuous signal

Pulsed Signal UÊ is helpful when there is interference. Easier to distinguish from other signals.

Continuous Signal UÊ is better to be used when taking a depth measurement

Green LED blinking indicates respective signal is on

Push5. Signal Strength: P to select low (0.1W) or High(0.5W) output signal strength

Low output (0.1W)UÊ for normal tracing. Battery saving

High output(0.5W)UÊ for long tracing

Green LED blinking indicates respective signal is on

R-3500 Receiver

Push and Hold the Control1 button6.

Push brieﬂy the ON/OFF button7.



while holding control1 button

Listen for the audible signal before releasing control1UÊ

The display shows the following:UÊ

8.

Push control3 to select the unit of measurement (meter 8. or ft )

Push Control1 to select normal depth measurement9. or depth measurement using the mouse

6

Push10.

OK

button to save the setting.

An audible sound is heardUÊ

The display shows the main menu: UÊ

Push Control3 to select the mode of operation11.

RadioUÊ for locating cables carrying VLF re-radiated radio signals (No need for T-3500)

Power GridUÊ for locating main power cables that carry electrical current (No need for T-3500)

Transmitter UÊ for locating cables or pipes carrying the signal of the T-3500 transmitter.

Push Control2 twice rapidly to select automatic or manual sensitivity adjustment12.

Automatic sensitivity adjustment: UÊ

Manual Sensitivity adjustment: UÊ

Push control1 to decrease sensitivity adjustmenti.

Push control3 to increase sensitivity adjustmentii.

Push Control2 to start a depth measurement.iii.

Hold the R-3500 receiver in an upright position in front of you as close to the ground as possible. Refer to Fig. 1.13.

Receiver in line with the conductor UÊ ¨ Maximum signal strength

Receiver perpendicular to the conductor UÊ ¨ minimum signal strength

APPLICATIONS AND PRINCIPLES OF DIRECT COUPLING

Single-wire cables or pipes (with or without insulation against ground)1.

The distance between the grounding rod and the ends of the connected lines should be as great as possible because return

current tends to ﬂow through the earth into adjacent lines, which could result in their path being followed.

Single-wire cable with metallic screen and ground insulation2.

Short circuit between internal conductor and screen at the end of the cable with ground at the beginning and end of the

cable as well.

Failure to make the connection as shown will result in current cancellation from the internal conductor and the return current

in the screen. Under certain circumstances this can prevent the cable from being detected.

Multiple-wire cable (internal conductor connected or disconnected) with metallic screen and grounding insulation3.

Same application as in example 1

Metallic conduit (with or without insulation) 4.

the grounding rod and the conduit should be spaced as far apart as possible. Under certain circumstances, optimum

positioning of the grounding rod may require several attempts.

If a return wire is available5.

the spacing of the return wire should correspond to at least 10 times the depth of the line being located.

Pair of wires (with or without screen) with short circuit at the end of the cable6.

For twisted cable pair (with a length of lay of the twist greater or equal to the laying depth), the orientation of the cable can

be easily determined.

7

Adjacent lines which are horizontal to each other ¨ Minimum of the reception signal

Lines situated on top of each other vertically ¨ Maximum of the reception signal

Direct Coupling (Refer to Fig. 2.)

Connect the red test lead of the T-3500 transmitter with the conductor to be traced1.

Connect the black test lead of the T-3500 transmitter to ground using the grounding rod. Alternatively the black test lead 2.

may be clipped to the rim of a valve box or manhole cover.

Switch the T-3500 on3.

Select pulse or continuous signal transmission4.

Switch the R-3500 Receiver on5.

Begin to trace the cable from the point of application about 50-FT (15m) away6.

Move slowly over the cable. Decrease or increase the sensitivity as needed7.

Direct Coupling using the A-3500 Clamp (Refer to Fig. 3.)

Plug the SC-3500 clamp into the T-3500 transmitter connection socket1.

Place the clamp around the pipe or cable2.

Switch the T-3500 transmitter on3.

Set the T-3500 transmitter to pulse or continuous signal transmission4.

Switch the R-3500 Receiver on5.

Select transmitter 6.

Begin to trace the cable from the point of application about 15m away7.

Inductive Coupling (Refer to Fig. 4.)

Position the T-3500 transmitter above the presumed cable1.

Switch on the T-3500 transmitter2.

Switch on the R-3500 receiver3.

Select the appropriate mode. Refer to section: Operation:R-35004.

Begin to trace the line from the transmitter at least 15m away.5.

Make sure that a distance of at least 50-FT (15m) is always maintained between the receiver and transmitter in order to 6.

prevent the coupling of the transmitter’s signal through the air.

Locating Passive Lines (Radio and Power Modes) (Refer to Fig. 5.)

The R-3500 Receiver can locate passive cables that carry radio signals in the frequency range between 15 kHz and 23 kHz as well

as power signals between the range of 50 Hz and 60 Hz without the help of the T-3500 Transmitter.

Turn the R-3500 Receiver on1.

Select radio mode or power mode. Refer to section 8 OPERATION.2.

Set the sensitivity to maximum3.

Sweep the area using a grid pattern as shown below4.

Adjust the sensitivity to pinpoint the conductor5.

Rotate the R-3500 to ﬁnd the maximum response6.

Locating unknown cables (Refer to Fig. 6.)

Use the T-3500 Transmitter using the inductive mode. 1.

Use the R-3500 Receiver to sweep the area. Keep the receiver 50-FT (15m) apart from the transmitter.2.

Select the desired mode of operation. 3.

Adjust the sensitivity of the R-3500 as needed4.

When a conductor is located, pinpoint the strongest signal and mark the location5.

Repeat steps 1 and 2. Move the transmitter at least 3.3-FT (1m) and 90-degree from the initial position.6.

Repeat the process until the right cable is detected. 7.

Depth Measurement (Refer to Fig. 7.)

Connect the T-3500 transmitter with the cable or the metallic pipe1.

Turn the T-3500 transmitter on. Use continuous signal mode for better result2.

Turn the R-3500 receiver on and move at least 50-FT (15m) away from the transmitter3.

Rotate the R-3500 receiver until the maximum signal strength is detected4.

Push control15. to take an automatic depth measurement

The measurement will display as follow:6.

To change the unit of measure, refer to R-3500 mode of operation (section 8).7.

For non-metallic pipe, use the M-3000 mouse. Refer to R-3500 receiver mode of operation section 9 to set the receiver 8.

accordingly.

8

For Power and Radio signals, an estimated depth measurement can be taken as follow:9.

Push control3 to select Power or Radio mode a.

Move to one side of the suspected cable until the following symbol appears: b.

Mark the spotc.

Move to the other side until the symbol appears againd.

Mark the spote.

Measure the distance between the two spotsf.

Divide the measurement by 2 to ﬁnd the depth of the cable.g.

ERROR MESSAGES DURING A DEPTH MEASUREMENT

Symbol Meaning

For of one of the following reasons, the depth could not be measured:

% The signal received was too weak or too irregular.

% The receiver was not held steady enough during the measuring process.

The receiver was not positioned directly above the line at the beginning of the process.

The depth of the metallic conductor amounts to more than 5 m (16 ft).

The depth of the metallic conductor amounts to less than 30 cm (1 ft). Such conductors must

be specially marked in order to prevent damage during construction.

The receiver was moved too far to the left or right while making a rough estimate. Move in

the opposite direction until the following symbol appears:

TECHNICAL SPECIFICATIONS

R-3500

The following parameters are speciﬁed for the R-3500 receiver:

Frequency ranges

UÊ,>}iÊ£\ÊÀ>`ÊÊ Ê £xÊâÊÌÊÓÎÊâ

UÊ,>}iÊÓ\Ê«ÜiÀÊiÌÜÀÊ xäÊâÊÉÊÈäÊâÆÊ«Ì>ÞÊ£ääÊâÊV>ÊLiÊ>`ÕÃÌi`ÊLÞÊ«ÀLiÊÃiÀÛViÊ«iÀÃi®

UÊ,>}iÊÎ\ÊÌÀ>ÃÌÌiÀÊ Ê ÎÓ°ÇÈnÊâ

Sensitivity at a depth of 1m

UÊ,>}iÊ£\ÊÀ>`Ê Ê ÓäÊ

UÊ,>}iÊÓ\Ê«ÜiÀÊiÌÜÀÊ ÇÊ

UÊ,>}iÊÎ\ÊÌÀ>ÃÌÌiÀÊ Ê xÊ

Dynamic response range

UÊ,>}iÊ£\ÊÀ>`Ê Ê £ÓäÊ`

UÊ,>}iÊÓ\Ê«ÜiÀÊiÌÜÀÊ £ÎxÊ`

UÊ,>}iÊÎ\ÊÌÀ>ÃÌÌiÀÊ Ê £ÓäÊ`

Depth determination

UÊi«ÌÊÀ>}iÊ Ê ä°£ÊÊoÊxÊÊ{ÊÊoÊ£ÈÊvÌ®

9

UÊ,iÃÕÌÊÊ Ê ä°£Ê

UÊVVÕÀ>VÞ

- Range 1: radio ±20 %

- Range 2: power network ±20 %

ÊÊÊÊ,>}iÊÎ\ÊÌÀ>ÃÌÌiÀÊ Ê ´xÊ¯ÊxÊÈ/®®]Ê´ÓäÊ¯ÊxÊ£x/®®

Power supply 10 x IEC R6 / AA cell / Mignon

Operating time 40 hours (for intermittent use with alkaline batteries, 20 °C)

Temperature range in accordance with DIN EN 60068-1

UÊ"«iÀ>ÌÊ Ê Ê ÓäÊcÊÌÊ³xxÊc

UÊ-ÌÀ>}iÊ Ê Ê ÎäÊcÊÌÊ³ÇäÊc

Weight 2.5 kg, 5.51 lbs.

Dimensions (W x H x D) 99 x 660 x 252 mm, .3.90 x 25.98x 9.92 in

Type of protection in accordance with EN 60529

Dust and water protected IP 67 from the lower edge of the receiver up to the lower edge of the battery

compartment, and IP 56 for all parts above this delineation

T-3500

The following parameters are speciﬁed for the T-3500 transmitter:

Transmitted power 0.1 W / 0.5 W (switchable)

Frequency 32.768 kHz

Power supply 6 x IEC R20 / D cell / Mono

Operating time 40 hours (for intermittent use with alkaline batteries, 20 °C)

Temperature range in accordance with DIN EN 60068-1

UÊ"«iÀ>ÌÊ Ê Ê ÓäÊcÊÌÊ³xxÊc

UÊ-ÌÀ>}iÊ Ê Ê ÎäÊcÊÌÊ³ÇäÊc

Weight 1.7 kg, 3.75 lbs.

Dimensions (W x H x D) 260 x 255 x 140 mm,

Type of protection in accordance with EN 60529

Dust and water protected IP 56

MAINTENANCE

Changing the battery in the R-3500 receiver

The status of the receiver’s batteries is checked upon start-up and indicated in the display.

The system regularly checks the battery strength as well. If battery capacity falls below 10 % of the threshold value, an audible

warning signal is given and the current status of the batteries is shown in the upper part of the display.

10

In order to replace the ten 1.5 V mignon (AA) batteries, the battery housing must be removed as described in the following

illustrations:

Changing the batteries in the T-3500 transmitter

The batteries in the transmitter have to be replaced as soon as the red LED battery indicator starts to blink.

Should this occur while the user is busy locating a line with the receiver, he/she will be informed of the weak batteries via the

reception signal:

Ty pe of signal Normal signal Signal when batteries are weak

In order to change the six 1.5 V mono (D cell) batteries, both screws on the back of the transmitter must be (e.g. with the aid of

a coin) turned through ¼ turn (1) and the battery tray must be pulled (2). Please note that all the batteries are ﬁtted in the same

direction.

11

Changing the ﬂoor cap on the R-3500 receiver

The plastic ﬂoor cap, which prevents the tip of the receiver from being damaged, can be easily replaced with the aid of a pointed

object (e.g. screw driver). Replacements can be ordered through the SEBA KMT sales team.

12

Fig. 1

Fig. 3

Fig. 2

13

Fig. 4

Fig. 5

Fig. 6

14

Fig. 7

15

Français

AT-3500

Système de détection de

conduits/câbles souterrains

Mode d’emploi

AT3500_Rev001

16

Limites de garantie et de responsabilité

Amprobe garantit l’absence de vices de matériaux et de fabrication de ce produit pendant une période d’un an prenant effet à

la date d’achat. Cette garantie ne s’applique pas aux fusibles, aux piles jetables ni à tout produit mal utilisé, modiﬁé, contaminé,

négligé ou endommagé par accident ou soumis à des conditions anormales d’utilisation et de manipulation. L’obligation de

garantie d’Amprobe est limitée, au choix d’Amprobe, au remboursement du prix d’achat ou à la réparation/remplacement

gratuit d’un produit défectueux. Les revendeurs n’ont pas l’autorisation de prolonger toute autre garantie au nom d’Amprobe.

Pour bénéﬁcier de la garantie, renvoyez le produit accompagné d’un justiﬁcatif d’achat auprès d’un centre de services agréé

par Amprobe Test Tools ou d’un distributeur ou d’un revendeur Amprobe. Voir la section Réparation pour tous les détails.

La présente garantie est votre recours exclusif. Toutes autres garanties, explicites, implicites ou statutaires, notamment le cas

échéant, les garanties de qualité marchande ou d’adaptation à un objectif particulier sont exclues par les présentes. Amprobe,

la société mère ou ses ﬁliales ne peuvent en aucun cas être tenues responsables des dommages particuliers, indirects, accidentels

ou consécutifs, ni d’aucuns dégâts ou pertes de données, sur une base contractuelle, extra-contractuelle ou autre. Etant donné

que certaines juridictions n’admettent pas les limitations d’une condition de garantie implicite ou l’exclusion ou la limitation de

dégâts accidentels ou consécutifs, il se peut que les limitations et les exclusions de cette garantie ne s’appliquent pas à votre cas.

Réparation

Tous les outils de test renvoyés pour un étalonnage ou une réparation couverte ou non par la garantie doivent être accompagnés

des éléments suivants : nom, raison sociale, adresse, numéro de téléphone et justiﬁcatif d’achat. Ajoutez également une brève

description du problème ou du service demandé et incluez les cordons de mesure avec l’appareil. Les frais de remplacement ou

de réparation hors garantie doivent être acquittés par chèque, mandat, carte de crédit avec date d’expiration, ou par bon de

commande payable à l’ordre de Amprobe® Test Tools.

Remplacements et réparations sous garantie – Tous pays

Veuillez lire la déclaration de garantie et vériﬁer la pile avant de demander une réparation. Pendant la période de garantie,

tout outil de test défectueux peut être renvoyé auprès de votre distributeur Amprobe®Test Tools pour être échangé contre

un produit identique ou similaire. Consultez la section « Where to Buy » sur le site www.amprobe.com pour obtenir la liste

des distributeurs dans votre région. Au Canada et aux Etats-Unis, les appareils devant être remplacés ou réparés sous garantie

peuvent également être envoyés dans un centre de services Amprobe® Test Tools (voir page suivante pour les adresses).

Remplacements et réparations hors garantie – Canada et Etats-Unis

Les appareils à réparer hors garantie au Canada et aux Etats-Unis doivent être envoyés dans un centre de services Amprobe®Test

Tools. Appelez Amprobe® Test Tools ou renseignez-vous auprès de votre lieu d’achat pour connaître les tarifs en vigueur de

remplacement ou de réparation.

Aux Etats-Unis Au Canada

Amprobe Test Tools Amprobe Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 888-993-5853 Tel: 905-890-7600

Fax: 425-446-6390 Fax: 905-890-6866

Remplacements et réparations hors garantie – Europe

Les appareils européens non couverts par la garantie peuvent être remplacés par votre distributeur Amprobe® Test Tools pour

une somme nominale. Consultez la section « Where to Buy » sur le site www.amprobe.com pour obtenir la liste des distributeurs

dans votre région.

Adresse postale européenne*

Amprobe® Test Tools Europe

Beha-Amprobe GmbH

In den Engematten 14

79286 Glottertal, Germany

Tel.: +49 (0) 7684 8009 - 0

*(Réservée à la correspondance – Aucune réparation ou remplacement n’est possible à cette adresse. Nos clients européens

doivent contacter leur distributeur.)

17

1

2

3

4

5

Tableau de commande avec afﬁchage

Haut-parleur avec réglage du volume



Fiche de casque (casque d’écoute de 3,5 mm non compris)

Logement des piles

Dispositif de protection au sol (amovible)

Diminution

du volume

Augmentation

du volume

Capteur lumineux : Règle automatiquement la

luminosité de l’afﬁchage

Commutateur marche/arrêt



Afﬁchage : Indication visuelle de l'intensité du signal,

mesure de profondeur et mode de fonctionnement,

état des piles et éléments de menus.

Commande 1

Commande 2

Commande 3

Indicateur de batterie : Le témoin de batterie clignote

en rouge lorsque la batterie est presque épuisée

Bouton marche/arrêt



Type de signal : Permet de basculer entre le signal

impulsionnel et continu en sortie

Jacks d’entrée

Mode : Permet de basculer entre couplage de signal

direct et inductif

Intensité du signal : Permet de sélectionner l’un des

deux niveaux d’intensité de signal (0,1 W ou 0,5 W)

+

123

1

2

3

456

Récepteur R-3500

Afﬁchage du R-3500

Emetteur T-3500

18

AT-3500

Système de détection de conduits/câbles souterrains

TABLE DES MATIÈRES

Déballage et inspection............................................................................................................................................................................. 5

Introduction................................................................................................................................................................................................ 5

Fonctionnement......................................................................................................................................................................................... 5

Applications et principes du couplage direct........................................................................................................................................... 6

Couplage direct..................................................................................................................................................................................... 7

Couplage direct à l’aide de la pince SC-3500...................................................................................................................................... 7

Couplage inductif ................................................................................................................................................................................. 7

Localisation des lignes passives (modes Radioélectrique et Alimentation) ...................................................................................... 7

Localisation des câbles inconnus.......................................................................................................................................................... 7

Mesure de profondeur ......................................................................................................................................................................... 7

Messages d’erreur pendant une mesure de profondeur......................................................................................................................... 8

Caractéristiques techniques....................................................................................................................................................................... 8

Entretien..................................................................................................................................................................................................... 9

Changement de la batterie du récepteur R-3500............................................................................................................................... 9

Changement des piles dans l’émetteur T-3500................................................................................................................................. 10

Changement du dispositif de protection au sol du récepteur R-3500 ............................................................................................ 11

La page charge ...

Amprobe AM-AT3500 Le manuel du propriétaire

Amprobe AM-AT3500 Le manuel du propriétaire

dans d''autres langues

Documents connexes