Genie TCM Manuel utilisateur

Genie
Marque
Genie
Modèle
TCM
Taper
Manuel utilisateur
U
L
®
C US
NOT FOR RESIDENTIAL USE
CLASS 2 SUPPLY 0-40 VOLTS DC - 20AWG WIRE SIZE MIN
120 VAC / 3A MAX
TMR
HOLD
GND GND GND GND GND
I/O
WARN
+24
VDC
TMR
RUN
TCM
OK
TMR
HOLD
GND
I/O WARN
AUX
OPEN
AUX
IN 2
AUX
IN 1
N - C
SAF
MON
EDGE
This installation manual provides the information required to install,
troubleshoot, and maintain the TIMER CLOSE MODULE (TCM) for
commercial/industrial door operators.
06/2017112069.503553
TIMER CLOSE
EXPANSION MODULE
Table of Contents
Section 1
Safety Information ......................................................................................................................................................................... 1-3
Section 2
General Information .......................................................................................................................................................................... 4
Entrapment Recommendations & Protections .................................................................................................................... 4-5
Job Site Issues ...................................................................................................................................................................................... 5
Section 3
Installation Warnings ........................................................................................................................................................................ 6
Installation MX units ......................................................................................................................................................................... 7
Installation SX-HX units ....................................................................................................................................................................8
Installation CX units ........................................................................................................................................................................... 9
Section 4
Wiring Information and warnings ..............................................................................................................................................10
Wiring MX units ................................................................................................................................................................................. 11
Wiring SX-HX units ........................................................................................................................................................................... 12
Wiring CX units .................................................................................................................................................................................. 13
Terminal Designations .................................................................................................................................................................... 14
Examples .............................................................................................................................................................................................15
Section 5
Setup .............................................................................................................................................................................................. 16-17
Section 6
Troubleshooting ........................................................................................................................................................................ 18-19
Section 7
Warranty Information .....................................................................................................................................................................21
1
The TCM package includes one of the Warning Placards shown below.
Place the placard next to the wall control of the door that will be
controlled by the TCM.
It must be in plain view and immediately adjacent to the door.
WARNING
AVERTISSEMENT
MOVING DOOR can cause serious
injury or death.
MOUVEMENT PORTE peut causer des
blessures graves ou la mort.
STAND CLEAR!
Door could close automatically.
Do Not stop or stand in doorway
SE TENIR À L'ÉCART DE LA PORTE!
La porte pourrait se refermer automatiquement.
Ne pas arrêter ou debout dans la porte.
Section 1 : Safety Information
2
WARNING
!
Overhead Doors are large, heavy objects that move with the help of springs under high tension and electric motors.
Since moving objects, springs under tension, and electric motors can cause injury, your safety and the safety of
others depend on you reading the information in this manual. If you have any questions or do not understand
the information presented, call your nearest service representative. For the number of your local Genie Dealer, call
800-OK-GENIE and for Genie Factory Technical Advice, call 800-843-4084.
In this manual the words Danger, Warning, and Caution are used to stress important safety information. The word:
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION indicates potentially hazardous situation which, if not avoided, may result in injury or property
damage.
The word NOTE, is used to indicate important steps to be followed or important considerations.
!
!
!
IMPORTANT
READ PRIOR TO ANY DOOR OPERATION
1. Read manual and warnings carefully.
2. Keep the door in good working condition. Periodically lubricate all moving parts of door.
3. If door has a sensing edge, check operations monthly. Make any necessary repairs to keep it functional.
4. AT LEAST twice a year, manually operate the door by disconnecting it from the operator. The Door
should open and close freely. If it does not, the door must be taken out of service and a trained service
representative must correct the condition causing the malfunction.
5. The Operator Motor is protected against overheating by an internal thermal protector. If the motor
protector is tripped, a trained service technical may be needed to correct the condition which caused the
overheating. When the motor has cooled, thermal protector will automatically reset and normal operation
can be resumed.
6. In case of power failure, the door can be operated manually by pulling the release cable to disconnect the
operator drive system.
7. Keep instructions in a prominent location near the pushbutton.
POTENTIAL HAZARD EFFECT PREVENTION
MOVING DOOR
WARNING
Could result in Serious
Injury of Death
Do Not operate unless the doorway is in sight and free of
obstructions. Keep people clear of opening while door is
moving.
Do Not allow children to play with the door operator.
Do Not change operator control to momentary contact unless
and external reversing means is installed.
Do Not operate a door that jambs or one that has a broken
spring.
ELECTRICAL SHOCK
WARNING
Could cause Serious
Injury or Death
Turn o electrical poser before removing operator cover.
When replacing the cover, make sure wires are not pinched or
near moving parts.
Operator must be electrically grounded.
HIGH SPRING TENSION
WARNING
Could cause Serious
Injury or Death
Do Not try to remove, repair or adjust springs or anything to
which door spring parts are fastened, such as wood block, steel
bracket, cable or any other structure or like item.
Repairs and adjustments must be made by trained service
representative using proper tools and instructions.
!
!
!
Section 1 : Safety Information
3
Section 1 : Safety Information
Les portes basculantes sont de gros objets lourds qui fonctionnent à l’aide de ressorts soumis à une
haute tension et de moteurs électriques. Dans la mesure où les objets en mouvement, les ressorts
sous tension et les moteurs électriques peuvent entraîner des blessures, votre sécurité et celle des
autres exigent que vous preniez connaissance des informations stipulées dans ce manuel. Si vous
avez des questions ou si vous ne comprenez pas les informations ci-incluses, veuillez contacter
le représentant de service le plus près. Pour obtenir le numéro du revendeur Genie local, appelez
le +1 (800) OK-GENIE, et pour obtenir des conseils techniques de l’usine Genie, appelez le +1
(800) -843-4084.
Dans ce manuel, les mots Danger, Avertissement, et Attention sont utilisés pour faire ressortir
d’importantes informations relatives à la sécurité. Le mot :
DANGER signale une situation dangereuse imminente qui si elle n’est pas évitée, risque
d’entraîner des blessures graves, voire mortelles.
AVERTISSEMENT signale une situation potentiellement dangereuse qui, si elle n’est pas évitée,
risque d’entraîner la mort ou des blessures graves.
ATTENTION signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque
d’entraîner des blessures ou des dommages matériels.
Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants
éléments à prendre en considération.
AVERTISSEMENT
!
!
!
!
DANGER POTENTIEL EFFET PRÉVENTION
PORTE EN MOUVEMENT
AVERTISSEMENT
Pourrait entraîner des
blessures graves voire la mort
Utiliser uniquement si la porte est en vue et libre de tout
obstacle. Ne laisser personne se tenir dans l’ouverture de la porte
pendant qu’elle est en mouvement.
Ne pas permettre aux enfants de jouer avec l’opérateur de la
porte.
Ne pas modier la commande de l’opérateur à contact
momentané à moins qu’un moyen d’inversion externe soit
installé.
Ne pas faire fonctionner une porte qui bloque ou dont le ressort
est cassé.
CHOC ÉLECTRIQUE
AVERTISSEMENT
Pourrait entraîner des
blessures graves voire la mort
Couper le courant avant d’enlever le couvercle de l’opérateur.
Lorsque le couvercle doit être remplacé, s’assurer que les ls ne
sont ni coincés ni près des pièces mobiles.
L’opérateur doit être correctement mis à la terre.
TENSION ÉLEVÉE RESSORT
AVERTISSEMENT
Pourrait entraîner des
blessures graves voire la mort
Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou
toute autre pièce à laquelle le ressort de la porte est attaché, y
compris blocs de bois, supports en acier, câbles ou autres articles
semblables.
Les réparations et les réglages doivent être eectués par
technicien qualié qui se sert d’outils appropriés et qui respecte
les instructions.
!
!
!
4
Timer Close Module Entrapment Protection Requirements:
This module provides the operator with an automatic door closing feature with a user selectable time delay,
auxiliary control inputs and auxiliary reversing inputs.
At power up, the system checks all inputs to verify they are in the proper state. i.e. Normally open or
normally closed, if the system determines that an input is not in the correct state, the input will be ignored
until it changes to the correct state. Refer to page 14.
The Timer Close Module allows the connection of any combination of the following Reversing Devices:
• A 2-wire “DC” Monitored Edge.
• A 2-wire Monitored Photocell (ODC Series II STB) on the operator control board.
• A Normally-Closed Reversing Device.
NOTE: The Monitored Edge Sensor input can detect open or shorted wiring to the Edge Sensor using a
2-wire connection. No relay kit is required to provide this feature.
NOTE: Any MillerEdge® T3 Sensor Series desired may be used as long as the 2-wire output is specied along with
the sux “DC.”
For example: Model number MT21-2R-16DC signies an MT21 Series sensor with a 2-wire output from the Right,
that is 16 feet long and has the monitoring option required by the Timer Close Module . Contact MillerEdge® at
1.800.220.EDGE For more specic information pertaining to sensing edges.
NOTE: Use of ASO Sentir GF Series T3 Edges is approved for use with Genie Commercial operators with this TCM
expansion module or ESM expansion module.
TIMER:
The timed closing feature is programmed with the operator keypad to start the timer when the door is
operated from any combination of the following inputs:
Section 2 : General Information
WARNING
DO NOT use with resister style 2-wire monitored edges
!
AVERTISSEMENT
NE PAS utiliser avec des arêtes surveillées à 2 ls de type à résistance
!
5
NOTE: Successive activations of an input that is programmed to start the timer or an active reversing input
will reset the timer and hold the timer until the input is deactivated.
Pressing the STOP wall button or STOP keypad key while the Timer Close Module is timing down will cancel
the Timer Close operation.
Additional activations of inputs selected to start the timer will start a new timing cycle. If a safety device
reverses the door 3 consecutive times, without the operator reaching the down limit, the timer will turn o.
(See 3 strikes feature in set-up procedure).
NOTE: The Normally-Open Reversing Input on the operator control board may be used in combination with
any of the required Timer Close reversing devices.
Job Site Issues to Consider/Concerns:
The following list of items should be considered prior to installing the Timer Close Module at any job site.
• Door activation requirements for Timer Close Module. Examples of devices to initiate the Timer are:
3 button control stations (open button), radio controls, pull cords, loop detectors, photoelectric
controls, key switches, etc.
• Accessory equipment requirements. Examples include: horns, lights sirens, etc.
WARNING
The installation of an Impending Operation Warning Device is strongly
recommended on every door equipped with a timer controlled automatic
closing feature. These signaling devices may include, but are not limited to:
lights, annunciators, voice modules, etc.
!
AVERTISSEMENT
Il est fortement recommandé d’installer un appareil avertissant un
fonctionnement imminent à chaque porte équipée d’un dispositif de fermeture
automatique contrôlée par une minuterie.
Ces dispositifs de signalisation peuvent inclure, sans toutefois s’y limiter:
lumières, voyants, modules vocaux, etc.
!
Section 2 : General Information cont.
• Open button on the 3-Button Wall Console.
• Radio Control Input.
• Auxiliary Open Input (provided on the Timer Close Module).
The time delay is adjusted using the calibration display on the keypad. This delay can be adjusted from 1
second to 5 minutes, plus 2 to 10 seconds for the Impending
Operation Warning Delay. (A set of dry relay contacts are provided that signal the impending closing of the
door prior to the beginning of the close cycle. It is used in combination with a signaling device, such as a
light, horn, etc.) The module also provides terminals for an input that suspends and resets the timer when
activated.
The Timer Close Module includes LED’s that indicate when power is applied, the normal functioning of the
module, when the Impending Operation Warning is active, when the timer is timing, and when the timer is
being held.
6
Section 3: Installation Information, All Operators
WARNING:
DO NOT use with resister style 2-wire monitored edges
!
AVERTISSEMENT
NE PAS utiliser avec des arêtes surveillées à 2 ls de type à résistance
!
WARNING
RISK OF ELECTRICAL SHOCK. Be sure that electrical power to the operator has been disconnected. There should be no live circuits
inside the electrical box while installing this Timer Close Module. An appropriate lock-out/tag-out procedure is recommended.
DO NOT APPLY POWER UNTIL INSTRUCTED TO DO SO.
!
AVERTISSEMENT
RISQUES DE CHOCS ÉLECTRIQUES Assurez-vous que l’alimentation électrique à l’opérateur a été coupée. Il ne doit pas y avoir de
circuits sous tension à l’intérieur du coret électrique lors de l’installation de ce module de fermeture à minuterie. Une procédure
de verrouillage/étiquetage appropriée est recommandée.
NE PAS METTRE SOUS TENSION TANT QUE L’INSTRUCTION N’EST PAS DONNÉE.
!
WARNING
All wiring to the operator must meet all local building codes. The Genie Company recommends that all work involving electrical
circuits and line voltage wiring be performed by a qualied electrician.
!
AVERTISSEMENT
Le câblage vers l’opérateur doit satisfaite aux codes de construction locaux. Genie Company recommande que les travaux
concernant les circuits électriques concernés et le câblage au secteur soient eectués par un électricien qualié.
!
CAUTION
Check working condition of door and operator before installing the Timer Control Module.
!
ATTENTION
Vérier l’état de marche de la porte et de l’opérateur avant d’installer le module de sortie auxiliaire.
!
7
1. Turn o supply power to the operator.
• Locate supply power disconnect.
• Disconnect supply power.
• Use proper lock-out/tag-out procedure.
2. Open and/or Remove Operator Electric Box Cover.
• Loosen screw on front of cover, door swings open. (Door is removed by sliding it out of the hinges).
3. Install Timer Close Module. (Fig. 3A)
• Secure with 1/4” hex head screws (2 ea.) provided.
• Connect ribbon cable to main control board as shown.
NOTE: If another expansion module is already installed and connected in the electric box, the Timer Close
Module ribbon cable should be connected to the expansion port connector on the existing expansion
module.
OPEN CL OSE
S TOP GND 1-BTN
N/O
S AFETY
N/O
S AFETY
ODC
STB
ODC
STB
E XT
INTLK
E XT
INTLK
L1
N
MOUNTING
SCREWS
RIBBON CABLE
CONNECTION
Fig.3A Install TCM in MX Unit
Section 3: Installation MX Operators
8
1. Turn o supply power to the operator.
• Locate supply power disconnect.
• Disconnect supply power.
• Use proper lock-out/tag-out procedure.
2. Open and/or Remove Operator Electric Box Cover.
• Loosen screw on front of cover, door swings open. (Door is removed by sliding it out of the hinges).
3. Install Timer Close Module. (Fig. 3B)
• Secure with 1/4” hex head screws (2 ea.) provided.
• Connect ribbon cable to main control board as shown.
NOTE: If another expansion module is already installed and connected in the electric box, the Timer Close
Module ribbon cable should be connected to the expansion port connector on the existing expansion
module.
115V
1 PH
208
230V
3 PH
Ribbon
Cable
Connection
Mounting
Screws
Fig.3B
Install TCM in SX-HX Units
Section 3: Installation SX-HX Operators
9
Section 3: Installation CX Operators
1. Remove four (4) self-tapping screws from front panel of CX® enclosure and remove front panel to expose
control circuits.
2. Orient the module so mounting bracket tabs are to the left and wire terminals are facing up.
3. Make desired wiring connections (see section 4)
4. Insert module into the area indicated and slide front mounting tab into slot on side panel of CX®
enclosure. Fig. 3C & D
5. Adjust module so that it is level with CX® enclosure.
• There is a mounting hole on side panel of enclosure which will line up with hole in module mounting
bracket.
• Attach module by inserting self-tapping screw (provided in kit) through module bracket and into
hole in side panel. Do not overtighten.
• Connect ribbon cable to main control board as shown.
6. Replace front panel.
MOUNTING
BRACKET
TAB
SLOT
Fig. 3C
Fig. 3D
Ribbon
Cable
Connection
Install TCM in CDX Units.
10
WARNING
RISK OF ELECTRICAL SHOCK. Be sure that electrical power to the operator has been disconnected. There should be no live
circuits inside the electrical box while installing this Timer Close Module. An appropriate lock-out/tag-out procedure is
recommended.
DO NOT APPLY POWER UNTIL INSTRUCTED TO DO SO.
!
AVERTISSEMENT
RISQUES DE CHOCS ÉLECTRIQUES Assurez-vous que l’alimentation électrique à l’opérateur a été coupée. Il ne doit pas y avoir de
circuits sous tension à l’intérieur du coret électrique lors de l’installation de ce module de fermeture à minuterie. Une procédure
de verrouillage/étiquetage appropriée est recommandée.
NE PAS METTRE SOUS TENSION TANT QUE L’INSTRUCTION N’EST PAS DONNÉE.
!
WARNING
LOWVOLTAGE/CONTROL WIRING MUST BE KEPT SEPARATE FROM LINE VOLTAGE WIRING!
!
AVERTISSEMENT
LE CÂBLAGE DE COMMANDE/BASSE TENSION SOIT ÊTRE DISTINCT DU CÂBLAGE DE TENSION DE LA LIGNE !
!
Section 4: Wiring Information, All Operators
11
Fig.4A Strip wire
Fig.4B Attach wire
OPEN CL OSE
STOP GND 1-BTN
N/O
SAFETY
N/O
SAFETY
ODC
STB
ODC
STB
EXT
INTLK
EXT
INTLK
L1
N
RADIO
CONTROL
TERMINALS
LOW VOLTAGE
CONTROL WIRE
TERMINALS
LOW
VOLTAGE
INPUT
Fig.4C Wiring to TCM
LINE VOLTAGE
INPUT
LINE VOLTAGE
TERMINALS
WIRING
To Connect Wires to Accessory Modules
1. Strip wire insulation .42” as shown. (Fig. 4A).
2. Using a screwdriver or your nger, press the plunger down and hold it.
3. Insert 20AWG - 12 AWG solid or stranded wire into the connector. (Fig. 4B).
NOTE: Connect only one wire per terminal.
4. Release the plunger.
5. Tug on the wire to make sure it is secured.
Control Wires
1. Route control wiring as per Fig. 4C.
2. Access ports have been provided so that wires can be routed into and secured to the control board. Use
appropriate conduit and/or ttings to provide proper strain relief and wiring protection.
3. Make control,warning and reversing device connections using the information above and on page 14.
NOTE: If wiring connected to the I/O Warning Output applies low voltage class 2 voltages/currents, route
the wiring with control wiring shown in left side of Fig 4C.
If wiring connected to this output applies line voltage, route the wiring as shown in right side of Fig 4C.
Section 4: Wiring MX Operators
12
Section 4: Wiring SX-HX Operators
Fig.4A Strip wire
Fig.4B Attach wire
115V
1 PH
208
230V
3 PH
Route Low Voltage Wiring
in Shaded Areas as Shown
Radio Control
Plug
Blu=24VDC
Org=Relay
Yel =Gnd
L1 -I- N
Route Line Voltage Wiring
in Shaded Areas as Shown
Fig.4C Wiring to TCM
To Connect Wires to Accessory Modules
1. Strip wire insulation .42” as shown. (Fig. 4A).
2. Using a screwdriver or your nger, press the plunger down and hold it.
3. Insert 20AWG - 12 AWG solid or stranded wire into the connector. (Fig. 4B).
NOTE: Connect only one wire per terminal.
4. Release the plunger.
5. Tug on the wire to make sure it is secured.
Control Wires
1. Route control wiring as per Fig. 4C.
2. Access ports have been provided so that wires can be routed into and secured to the control board. Use
appropriate conduit and/or ttings to provide proper strain relief and wiring protection.
3. Make control,warning and reversing device connections using the information above and on page 14.
NOTE: If wiring connected to the I/O Warning Output applies low voltage class 2 voltages/currents, route
the wiring with control wiring shown in top side of Fig 4C.
If wiring connected to this output applies line voltage, route the wiring as shown in bottom side of Fig 4C.
13
Section 4: Wiring CX Operators
Fig.4A Strip wire
Fig.4B Attach wire
S
S B
S Y
S YS B S B
TB
NAB
+ 24
VAC
EXT
NTLK
HO ST
NTLK
CAL
RUN
SET
CLR
CROL
CROL
Route Line
Voltage Wiring
Here
Route Low
Voltage Wiring
Here
To Connect Wires to Accessory Modules
1. Strip wire insulation .42” as shown. (Fig. 4A).
2. Using a screwdriver or your nger, press the plunger down and hold it.
3. Insert 20AWG - 12 AWG solid or stranded wire into the connector. (Fig. 4B).
NOTE: Connect only one wire per terminal.
4. Release the plunger.
5. Tug on the wire to make sure it is secured.
Control Wires
1. Route control wiring as per Fig. 4C.
2. Access ports have been provided so that wires can be routed into and secured to the control board. Use
appropriate conduit and/or ttings to provide proper strain relief and wiring protection.
3. Make control,warning and reversing device connections using the information above and on page 14.
NOTE: If wiring connected to the I/O Warning Output applies low voltage class 2 voltages/currents, route
the wiring with control wiring shown in upper side of Fig 4C. If wiring connected to this output applies line
voltage, route the wiring as shown in lower side of Fig 4C.
14
Section 4 : Wiring - Terminal Designations
Fig.4E Terminal
Arrangement
TWO
POSITION
TERMINAL
BLOCK
TWELVE
POSITION
TERMINAL
BLOCK
CLASS 2 SUPPLY 0-40 VOLTS DC - 20AWG WIRE SIZE MIN
120 VAC / 3A MAX
TMR
H OLD
G ND G ND G ND G ND G ND G ND
I /O WARN
AUX
O PEN
AUX
I N 2
AUX
I N 1
N - C
S AF
M ON
E DGE
Impending Operation Warning (I/O WARN) - Activates 2 to 10 seconds
(adjustable) before the close cycles. One set of SPST contacts rated at
3A, 120VAC (Max.)
Monitored Edge Sensor Input - When this input is enabled using the operator
keypad display, an active input will reverse a closing door, prevent an
open door from closing, or cause the timer to reset and hold if a timing
cycle is in progress. This is a 2-wire monitored edge sensor input when
used with a compatible edge sensor.
NOTE: Any MillerEdge® sensor series can be used as long as the 2-wire
output is specied along with the sux “DC”. Example: ME123-DC. This
input will detect broken or short circuit wiring to the edge sensor and will
interpret these as an active input. The edge sensor leads are not polarized,
so either lead can connect to either terminal.
NOTE: DO NOT use with resistor style 2-wire monitored edges.
Normally Closed Reverse Input - When this input is enabled using the
operator keypad display, disconnecting the input from ground (GND)
will reverse a closing door, prevent an open door from closing, or
cause the timer to reset and hold if timing cycle is in progress. This is a
Normally Closed switch to ground (GND).
Auxiliary Input 1 - Loop input. Activating this input causes a stopped or
closed door to open, prevents an open door from closing and reverses a
closing door. It can be programmed to activate the timer close feature.
Activating the input causes the timer to reset and hold if a timing cycle
is in progress. The timer will restart when this input is de-activated. This
is a Normally Open switch contact to ground (GND).
NOTE: The status of this input is not checked at power up.
Auxiliary Input 2 - This is a spare input that is not currently used.
Auxiliary Open Input - Activating this input causes a stopped or closed
door to open, prevents an open door from closing and reverses a
closing door. It can be programmed to activate the timer close feature.
Activating the input causes the timer to reset and hold if a timing cycle
is in progress. The timer will restart when this input is de-activated. This
is a Normally Open switch contact to ground (GND).
Timer Hold Input - An active input causes the timer to reset and hold. The
timer will restart when this input is de-activated. This is a Normally Open
switch contact to ground (GND).
NOTE: This input will not open a door or reverse a closing door.
NOTE: Maximum wire size = 12AWG
Minimum wire size = 20AWG
NOTE: The reversing inputs are enabled or disabled
using the operator keypad display.
15
Section 4 : Examples
120 VAC / 3A MAX
N
L1
I/O WARN
WARNING
DEVICE
120 VAC Powered Device
Normally
Closed
Sensing
Device
N - C
SAF
GND
N - C
SAF
GND
PWR RAD GND
EXTERNAL RADIO
TERMINAL STRIP
18-40 VDC @ 300mA
+
-
+
-
MX
BLUE
YEL
For units
with Radio
Plug
Harness
120 VAC / 3A MAX
I/O WARN
24 VDC (18-40 VDC) Powered Device (300mA Max.)
PWR RAD GND
EXTERNAL RADIO
TERMINAL STRIP
18-40 VDC @ 300mA
MX
WARNING
DEVICE
BLUE
YEL
For units
with Radio
Plug
Harness
INPENDING
OPERATION
DEVICES
NORMALLY
CLOSED
SENSING
DEVICES
Normally
Open
Input
TMR
HOLD
GND
Normally
Open
Input
AUX
OPEN
GND
Normally
Open
LOOP
Input
AUX
IN 1
GND
Monitored
Sensing Edge
System
MON
EDGE
GND
Monitored Circuit
Inside Edge Sensor
FIG. A FIG. B
FIG. C FIG. D
FIG. E FIG. F
Fig. F Monitored Edge Sensor
Edge sensor leads are not polarized.
Either lead can connect to either terminal
Note that the use of a Montitored
Edge Interface Module is not used in
this method.
Normally Closed Sensing Device
16
Section 5 : Setup Procedure
Timer to Close Options:
1. Turn on power to door operator.
• If Timer Close Module is properly installed, the +24V” and “TCM O.K.” will turn on.
(Fig. 5A) (See also page 18 —Troubleshooting Section.)
NOTE: One or more of the following Reversing devices must be installed to use the Timer Close feature:
• Monitored photocell (ODC Series II STB) (on control board).
• Monitored Edge Sensor
2. Using the operator keypad and display, press the CAL/RUN key to enter the CAL Mode.
3. Press the SCROLL DN key to select the installed reversing device(s), ODC STB > ON OFF,MON EDGE > ON/
OFF, or N-C SAFETY > ON/OFF.
4. Press the SET/CLEAR key to turn the selected reversing device on or o.
5. Press the SCROLL DN key to select the inputs that will initiate a Timer Close operation. (Fig. 5B). TIMER
CLOSE W/OPEN BUTTON, TIMER CLOSE W/RADIO or TIMER CLOSE W/AUX OPEN.)
6. Press the SET/CLEAR key to turn each timer-initiate input on or o.
Fig. 5A Timer Close
Module LED’s
I/O
WARN
+24V
TMR
RUN
TCM
OK
TMR
HOLD
TCw/AUX OPEN> ON
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
TCw/RADIO> ON
TCw/OPEN BTN> ON
Fig. 5B Select Mode
WARNING
RISK OF ELECTRICAL SHOCK. After power is applied to the Operator, DO NOT make contact with components inside the Control
Panel, except for the Keypad Display Buttons.
!
AVERTISSEMENT
RISQUES DE CHOCS ÉLECTRIQUES Après avoir mis l’opérateur sous tension, NE PAS entrer en contact avec des composants à
l’intérieur du panneau de commande, sauf pour les touches du pavé numérique.
!
17
Section 5 : Setup Procedure-cont.
Setting the Timer Delay:
1. Press the SCROLL DN key until display reads “TIMER DELAY> 0:01 ” . (Fig. 5C).
2. Press SET/CLEAR key to select the rst time digit (minutes).The cursor will blink in the minutes column.
• Press SET/CLEAR key to increase the delay 1 minute at a time until you reach the desired delay.
• Press the SCROLL DN key to shift to the next digit(10 seconds).The curser will blink in the10 seconds
column.
• Press SET/CLEAR key to increase the delay 10 seconds at a time.
• Press SCROLL DN key again to shift to nal digit (seconds).The cursor will blink in the seconds
column.
• Press SET/CLEAR key to increase delay 1 second at a time.
• Press SCROLL DN key again to lock the delay set.
NOTE: When setting the time delay you can move left and right through the Time Delay digit columns by
using the SCROLL UP or SCROLL DN keys as necessary.
3. Press SCROLL DN key again to shift to “I/O WARN DELAY > 02.” (Fig. 5D).
• Press SET/CLEAR key to adjust the delay between 2 and 10 seconds.
• Press the SCROLL DN key to lock the setting.
Setting the Three Strikes Option:
1. Press the SCROLL DN key to shift to “TC>3 STRIKES> ON-OFF”. Fig. 5E
2. Pressing the SET/CLEAR key will toggle this feature on and o.
NOTE: The 3 strikes feature ON will lock the timer out if the operator receives 3 safety inputs in a row while
door is closing from the timer and before it reaches the down limit.
An open command from a programmed initiation device will reset the TCM.
3. Press the CAL/RUN key to exit Cal Mode.
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
TIMER DELAY>0:01
Fig. 5C Set Timer Delay
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
I/O WARN DELAY>: 02
Fig. 5D I/O WARN Delay
CAL
RUN
SET
CLEAR
SCROLL
SCROLL
OPEN
CLOSE
STOP
Fig. 5E 3 Strikes
TC 3 STRIKES ON
18
Section 6: Troubleshooting
Status LED’s
STATUS INDICATION
ON — Impending Operation Warning delay is timing. Output is active.
OFF —
Impending Operation Warning delay is not timing. Output not active.
ON — Timer Close Module has power.
OFF — No power to the Timer Close Module.
ON — Timer Close delay is timing or pending
OFF — No Timer Close delay in progress
ON — Timer Close Module is functioning normally.
OFF — Timer Close Module is not functioning normally.
ON — Timer Close Module delay is pending but holding.
OFF — Timer Close Module delay is not holding.
Troubleshooting Guide
PROBLEM INDICATION CHECK
1. TCM has no power. +24V LED is OFF. 1. Check power to the operator.
2. Check that TCM ribbon cable is
connected to the operator control board
or another accessory module that is connected
to the o
perator control board..
3. Check fuse F2 on the operator control board.
4. Contact the factory.
2. TCM is not +24 V LED is ON. 1. Check that TCM ribbon cable is
functioning properly. TCM OK LED is OFF. connected to the operator control board
or another accessory module that is connected
to the operator control board.
2. Check that operator display is working
normally and not indicating a
system problem.
3.Turn power to the operator off, then back on.
4. Contact the factory.
Troubleshooting Guide
(
cont’
)
PROBLEM INDICATION CHECK
3. I/O Warning Device I/O WARN LED is ON 1. Check wiring between the warning device and the
.)4 noitces ees( slanimret tuptuo NRAW O/I.krow t’now
2. Check power to the Warning Device.
3. Check Warning Device operation.
4. Go to #2.
4. I/O Warning Device I/O WARN LED is OFF 1. If TMR HOLD LED is on, go to #6.
won’t work. 2. If TMR RUN LED is off, go to #5.
5. TCM will not start a TMR RUN LED is OFF 1. If TMR HOLD LED is on, go to #6.
timer cycle.
2. Check that activation device(s) will open the door.
3. Check that the Timer Close feature for the activation
device is turned “ON” using the operator keypad and
display (see sec
tion 5).
4. Go to #2
6. TCM starts a timer cycle TMR RUN LED is ON 1.Check that one or more devices set to start the Timer
but won’t close door. TMR HOLD LED is ON cycle is not active.
2. Check that one or more reversing devices is not
signaling an obstruction.
3. Check that Timer Hold input is not active.
4.
Attempt to close the door using the Close keypad key.
If the operator fails to close— or closes and
then reverses, the Error Code will indicate which
device may be holding the Timer operation
3. Go to #2.
7. TCM starts a Timer cycle. TMR RUN LED was 1. STOP wall button or STOP keypad key was/is active.
but won’t close door. ON, but is now off.
TMR HOLD LED is OFF
2. Go to #2.
8. Can’t turn
Timer Close On Calibration 1. One of the following reversing devices must be
feature “ON” for a display, the feature turned “ON” in Calibration Mode before you can
given input. will not toggle from turn the Timer Close feature “ON.” ODC STB
“OFF” to “ON” when (Monitored Series II Photocells “_” on operator
Set/Clear key control board), MON. EDGE (Monitored Edge
is pressed. Sensor) or N-C SAFETY (Normally-Closed Reversing
Input). (see section 5).
2. Go to #2.
9. Door reverses on +24 V LED is OFF. 1. Check operator display. The Error Code should
.lasrever eht gnisuac si tahw etacidni.stpmetta esolc
2.TCM is not functioning. If reversal is caused by an
input to the TCM or a faulty
TCM, normal door
operation (except Timer Close), can be restored by
turning off Monitored Edge Sensor (MON. EDGE)
and Normally Closed Reversing Input (N-C SAFETY)
in Calibration Mode (see section 5.)
3. Or go to #1.
Fig. 6A
I/O
WARN
+24V
TMR
RUN
TCM
OK
TMR
HOLD
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Genie TCM Manuel utilisateur

Genie
Marque
Genie
Modèle
TCM
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents