GX-140C / CH
STEREO CHORUS AMPLIFIER
OWNER’S MANUAL
Congratulations!
You are now the proud owner of the versatile and powerful Crate GX-140C
Combo Amplifier / GX-140CH Amp Head with Stereo Chorus. With two flexible
channels, Crate’s patented “Flex Wave” distortion circuitry, a Stereo Effects Loop
and three footswitchable functions, the GX-140C/CH offers you more flexibility
and performance than any amplifier in its class.
Like all Crate products, your GX-140C/CH is Musician Made in the U.S.A.,
using only the best components. Extensive testing at the hands (and ears) of
skilled technicians and musicians insures you that this amplifier is the absolute
best it can be.
In order to get the most out of your new amplifier, we strongly urge you to go
over the information contained in this manual before you begin playing.
And thank you
for choosing
1 2 3 4 6 7 8 10 11 12 13 14 15 19 20 21165 9 17 18
FRONT PANEL:
1: INPUT: Connect your guitar here using a shielded
instrument cable.
OVERDRIVE CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
2: GAIN 1: When active, sets the amount of compression
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 1 pro-
duces less intense distortion than Gain 2 and is active only
when the Gain Select switch (#5) is out.
3: GAIN 2: When active, sets the amount of compression
and distortion from the amplifier. At far left, the sound will
have a thick compressed quality. As you turn the control to
the right the amount of distortion increases. Gain 2 is pro-
duces more intense distortion than Gain 1 and is active
only when the Gain Select switch (#5) is in.
4: SHAPE: Working in conjunction with the Gain 2 control,
rotate the Shape control until you find the sound you’re
looking for. Turning the control towards the left enhances
the mid frequencies; turning it to the right enhances the low
and high frequencies. (Only affects Gain 2 when active.)
5: GAIN SELECT: Switches between Gain 1 (out) and
Gain 2 (in). A footswitch (see #28, rear panel) overrides
this switch.
6: LOW: Adjusts the low frequency output level: to the left
reduces the low frequency output; to the right increases it.
This control allows a range of 10dB at 80Hz.
7: HIGH:Adjusts the high frequency output level: to the left
reduces the high frequency output, to the right increases it.
This control allows a range of 10dB at 7kHz.
8: LEVEL: Sets the output volume level from Channel A: in
the far-left position there is no output; turning the control to
the right increases the output. Use this control along with
the Gain and Shape controls (#2, 3 & 4) to create a wide
variety of sounds.
9: CHANNEL SELECT: When this switch is pressed in the
Overdrive Channel is engaged. The Clean Channel is
selected when this switch is out. Afootswitch (see #28, rear
panel) overrides this switch. The adjacent LEDs indicate
which channel is selected.
CLEAN CHANNEL: A normal gain channel designed to
give you crystal clear sounds.
10: LEVEL: Sets the output volume level from the Clean
Channel: in the far-left position there is no output; turning
the control to the right increases the output level.
11: LOW:Adjusts the low frequency output level: to the left
reduces the low frequency output; to the right increases it.
This control allows a range of 20dB at 100Hz.
12: MID: Adjusts the mid frequency output level: to the left
reduces the midrange output; turning it to the right increas-
es it. This control allows a range of 14dB at 700Hz.
13: HIGH: Adjusts the high frequency output level: to the
left reduces the high frequency output; to the right increas-
es it. This control allows a range of 27dB at 10kHz.
14: REVERB, OVERDRIVE: Adjust the amount of reverb
for the Overdrive Channel with this control: in the full-left
position the output signal is “dry” (no reverb); rotating the
control to the right increases the amount of effect.
15: REVERB, CLEAN:Adjust the amount of reverb for the
Clean Channel with this control: in the full-left position the
output signal is “dry” (no reverb); rotating the control to the
right increases the amount of effect.
16: INSERT LOOP: Connect an external effects device via
this jack. Use a stereo 1/4” male Y-cord: ring = send, tip =
return, sleeve = ground. See the illustration on the panel to
the right for more information. This is a mono pre-chorus
effects loop.
17: CHORUS ON/OFF: Turn the Chorus/Expander on and
off with this switch. When the switch is pressed in, the
Chorus/Expander is active. A footswitch (see #29, rear
panel) overrides this switch.
18: CHORUS/EXPANDER: Select between the built-in
stereo chorus or the “expander” circuit with this switch.
When the switch is pressed in, the chorus section is select-
ed. When the switch is out, the amplifier’s expander circuit
is activated, giving the sound a wide-open, “spatial” effect.
In order for either effect to be active, the Chorus On/Off
switch (#17) must be pressed in.
19: DEPTH: Set the intensity of the chorus effect with this
control: in the far left position there will be almost no cho-
rus; as you rotate the control to the right the amount of
effect increases.
20: RATE: Set the speed of the chorus effect with this con-
trol: to the left for slow, smooth “phasing” sounds, to the
right for faster “vibrato” sounds.
21: POWER SWITCH: Turns the amplifier ON in the up
position, off in the down position. The Channel LED for the
selected channel will light when the amp is switched on.
GX-140C/CH Amplifier
REAR PANEL:
22: AC LINE IN: This heavy-duty, grounded, three-wire
power cord is to be plugged into ONLY a safely-wired,
grounded 120 volt, 60 cycle AC power outlet. DO NOT
attempt to defeat the ground connection of this cable! If
your GX-140C/CH was purchased outside of the United
States, see the unit’s rear panel for its power rating and fol-
low the above guidelines.
23,24: POWER AMP 1, 2 SPEAKERS: You may connect
the outputs of the GX-140C/CH to your external speakers
using these jacks. When connecting speakers use a
matched pair; that is, two speakers with the same imped-
ance to insure optimum performance from the amplifier.
The amp 2 speaker jack (#24) carries the chorus signal
(when the chorus is on) while the amp 1 jack (#23) is “dry”
(without the chorus effect).
NOTE: The total impedance for each side should not be
less than 4 ohms.
IMPORTANT NOTE ABOUT CERTAIN EXPORT UNITS:
In some areas 1/4” speaker jacks are not acceptable
for use on amplifiers capable of high output power
levels. For this reason the 1/4” speaker jacks on your
amplifier may be sealed – in this case, use the
Speakon
®
jacks provided.
25: STEREO LINE IN: When using a stereo effects
deivce, connect its output here. This stereo 1/4” phone
jack is wired as follows: Ring = amp 1, tip = amp 2, sleeve
= ground.
26: STEREO LINE OUT: When using a stereo effects
deivce, connect this jack to its input. This stereo 1/4”
phone jack is wired as follows: Ring = output 1, tip = out-
put 2, sleeve = ground.
If your effects device has stereo input and output jacks,
use a pair of three-conductor stereo patch cords to con-
nect to it. If the device has separate left and right jacks, use
a pair of one-stereo-male to two-mono-female Y-adapters
to make the connections, as shown to the right.
28: CHANNEL/GAIN SELECT FOOTSWITCH: Plug a
dual footswitch (such as the Crate CFP-2 or the “stereo”
plug of the Crate CFP-3) here to control Channel Selection
and the Gain Select button. The footswitch overrides the
front panel switches (#5 and 9) and is wired as follows:
Ring = Gain Select, tip = Channels, sleeve = ground.
29: CHORUS/EXPANDER FOOTSWITCH: Plug a single
footswitch (such as the Crate CFP-1 or the “mono” plug of
the Crate CFP-3) here to control the Chorus/Expander.
The footswitch overrides the front panel on/off switch
(#17); selection between the Chorus and the Expander is
still controlled by the front panel selector switch (#18).
Connecting to the Insert jack:
The Insert jack (#16) lets you patch external effects into the
amplifier just prior to its power amp stage. Use Crate’s
STP201, STP202 or STP203 stereo-to-mono Y-cord or an
adapter such as Crate’s YPP117 and 2 1/4” mono signal
cables to connect to the effect as shown below.
WARNING: DO NOT attempt to use headphones in the
Speaker jacks! Permanent hearing damage could result!
TIP
RING
SLEEVE
RETURN
SEND
GROUND
Stereo-to-mono Y-cord:
to Insert
jack
to Insert
jack
(STP201, 3'
STP202, 6'
STP203, 9')
(YPP117)
(1/4"-TO-1/4"
MONO SHIELDED
CABLES)
to
effect
"OUT"
jack
to
effect
"IN"
jack
External Effect
TIP
RING
SLEEVE
Y-adapter and 2 cables:
External Effect
RING
RING
TIP
TIP
to
effect
"OUT"
jack
to
effect
"IN"
jack
GX-140C/CH Amplifier
2322 24 2625 27 28 29
Speakon is a registered trademark of Neutrik U.S.A.
©2001 SLM ELECTRONICS, A DIVISION OF ST. LOUIS MUSIC, 1400 FERGUSON, ST. LOUIS, MO. 63133
P/N 47-474-01 • 05/01
GX-140C/CH Amplifier
Crate continually develops new products, as well as improves existing ones. For this reason, the
specifications and information in this Crate manual are subject to change without notice.
Output Power Rating 70 watts RMS @ 5% THD 8 ohms load 120VAC
100 watts RMS @ 5% THD 4 ohms load 120VAC
Speaker Size and Rating (GX-140C only) Crate Custom Design 12” with 1-3/4” voice coil
Power Handling: 65 Watts RMS
Maximum Input Signal Level Accepted 8 volts, peak-to-peak
Total System Gain Overdrive Channel: 108dB @ 1kHz
Clean Channel: 56dB @ 1kHz
Input Impedance 470k ohms
Overdrive Channel: Low Control: 10dB Range @ 80Hz
Shape Control: Proprietary Circuit
High Control: 10dB Range @ 7kHz
Clean Channel: Low Control: 20dB Range @ 100Hz
Mid Control: 14dB Range @ 700Hz
High Control: 27dB Range @ 10kHz
Input Power Requirements 120 VAC, 60Hz, 230VA
100/115VAC, 50/60Hz, 230VA
230VAC, 50/60Hz, 230VA
Cabinet Size and Weight: GX-140C: 20” H x 26-1/2” W x 11” D, 58 lbs.
GX-140CH: 12-1/2” H x 30-3/4” W x 10-1/2” D, 35 lbs.
The GX-140C/CH is covered with a durable black Tolex material:
wipe it clean with a lint-free cloth. Never spray cleaning agents onto
the cabinet. Avoid abrasive cleansers which could damage the finish.
GX-140C/CH TECHNICAL SPECIFICATIONS
THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED TO PROVIDE SAFE AND RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE
UNIT AND PREVENT ACCIDENTAL DAMAGES OR INJURY, PLEASE FOLLOW THESE PRECAUTIONARY GUIDELINES:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN CHASSIS; DO NOT DEFEAT OR REMOVE THE GROUND PIN OF THE POWER
CORD; CONNECT ONLY TO A PROPERLY GROUNDED AC POWER OUTLET.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE
LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS
OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
"UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN"
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
"GEFAHLICHE SPANNUNG"
=
=
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS
ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE
PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN
TECHNICIEN QUALIFIE.
VORSICHT
ELEKTRISCHE SCHLAGGEFAHR
NICHT OFFENEN
VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT
DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM
BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM
WARTUNGSPERSONAL ZU UBERLASSEN.
www.crateamps.com
-
1
-
2
-
3
-
4
Crate Amplifiers GX-140C Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Crate Amplifiers GX-140C User manual
Documents connexes
-
Crate Amplifiers GX-140D Manuel utilisateur
-
-
-
Crate Amplifiers GX-40M Manuel utilisateur
-
-
-
-
-
-