Jenn-Air JXW8030WS0 Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW8030WS0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

JENN-AIR®30", 36', AND 42"

, 91,4 CM AND 106,7 CM)

WALL-MOUNT CANOPY RANGE HOOD

HOWE DE CUISINIERE JENN-AI R

MONTAGE MURAL 30", 36'F 42"

(76,20M, 91,4 OM E-I-106,7 OM)

Forquestions about features, operation/performance, parts, accessories, or service inthe U.S.A.,call:

1-800-JI=NNAIR (1-800-536-6247} or visit our website at www.jennair.eom.

In Canada, call: 1-800-JI=NNAIR (1-800-536-6242}, orvisit our website at www.jennair.ea.

Au Canada, pour des questions apropos des caract@ristiques,du fonctionnement/rendement des pi@ces,accessoires ou service,

composer le 1-8@@-JENNAIR(1-8@@-536-6247)ou visiter notre siteweb a www.jennair.ca.

Tableof Contents/Table des mati@res...................................2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

iMPORTANT : URE ET CONSERVER CES iNSTRUCTiONS.

POUR UTILISATION Rf-=SIDENTIELLE UNIQUEMENT.

JENN-AIR °

LI3QIC/W10274311 E

TABLE OF CONTENTS

RANGE HOOD SAFETY .............................................................................. 2

INSTALLATION REQUIREMENTS ............................................................. 4

Tools and Parts ......................................................................................... 4

Location Requirements ............................................................................. 4

Venting Requirements .............................................................................. 5

Electrical Requirements ............................................................................ 6

INSTALLATION INSTRUCTIONS ............................................................... 6

Prepare Location ....................................................................................... 6

Install Range Hood ................................................................................... 7

Connect Vent System ............................................................................... 7

Make Electrical Connection ...................................................................... 8

Install Vent Covers .................................................................................... 9

Complete Installation ................................................................................ 9

RANGE HOOD USE ................................................................................... 10

Display ..................................................................................................... 10

Light ........................................................................................................ 11

Timer ....................................................................................................... 11

Fan Speed Buttons ................................................................................. 11

RANGE HOOD CARE ................................................................................ 12

Cleaning .................................................................................................. 12

WIRING DIAGRAM .................................................................................... 13

ASSISTANCE OR SERVICE ...................................................................... 14

In the U.S.A ............................................................................................. 14

Accessories ............................................................................................. 14

In Canada ................................................................................................ 14

WARRANTY ............................................................................................... 15

TABLE DES MATIERES

SI_CURITI_ DE I_AHOTTE DE CUlSlNII_RE ............................................ 17

EXlGENCES D'INSTALLATION ................................................................ 19

Outils et pieces ....................................................................................... 19

Exigences d'emplacement ..................................................................... 19

Exigences concernant I'evacuation ........................................................ 20

Specifications electriques ....................................................................... 21

INSTRUCTIONS D'INSTALLATION ......................................................... 22

Preparation de I'emplacement ............................................................... 22

Installation de la hotte ............................................................................. 23

Raccordement du circuit d'evacuation .................................................. 23

Raccordement electrique ....................................................................... 24

Installation des cache-conduits ............................................................. 25

Achever I'installation ............................................................................... 25

UTILISATION DE LA HOTTE .................................................................... 25

Affichage ................................................................................................. 26

Eclairage ................................................................................................. 26

Minuterie ................................................................................................. 26

Boutons de vitesse du ventilateur .......................................................... 26

ENTRETIEN DE LA HOTTE ...................................................................... 27

Nettoyage ............................................................................................... 2-/

SCHEMA DE C,&.BLAGE........................................................................... 28

ASSISTANCE OU SERVICE ...................................................................... 29

Au Canada .............................................................................................. 29

Accessoires ............................................................................................. 29

GARANTIE ............................................................................................... 30

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

m Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

m Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

m Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

m Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

m SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. Ifthe flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

m NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill with 11¼"(3.0 cm), 3/8"(9.5 mm), and 8/le"(7.9 mm) drill

bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

Parts needed

• Home power supply cable

• 1/2"(12.7 mm) UL listed or CSA approved strain relief

• 3 UL listed wire connectors

For vented installations, you will also need:

• 1 wall or roof cap

• Metal vent system

For non-vented (recirculating) installations, you will also

need:

• Recirculation Kit Part Number W10272060 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

• 8" (20.3 cm) dia. round metal vent duct - length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

• Hood canopy assembly with ventilator and light bulbs

installed

• Vent transition with back draft dampers installed

• Metal grease filter(s) - depending on model and size

• Vent cover support bracket

• Mounting template

• 2-piece vent cover

• 8-4x8screws

• 6- 5 x 45 mm mounting screws

• 2 - D6.4 x 18 mm washers

• 2 - 8 x 40 mm wall anchors

• 4- 10 x 50 mm wall anchors

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) installation see "For non-

vented (recirculating) installation only" in the "Connect Vent

System" section. Recirculation Kit Part Number W10272060 is

available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

10%" (27 4%" (11.7 cm)

7_%o'' (20.2 crn)

13¾o"

*28%6" (71.9 cm) rain.

42%" (108.3 cm) max.

24"cm )

**24%" (62.5 cm) rain.

Ore) max.

36" (91.4 cm). 12 7

42" (106.7 cm)_/__ _ ( .

--_ _ l_V_o"(50.0cm)

*For non-vented (recirculating) installations

**For vented installations

Cabinet Dimensions

10" (25.4 cm) rain.

13" (33.0 max.

2" (5.1 cm) rain.

)" (22.9 cm) rain.*

10" (25.4 cm) rain.

13" (33.0

Side

cabinet

Side

cabinet

30" (76.2

36" (91.4 cm) or

"X" 42" (106.7 cm)

bottom of I

canopy

to cooking I

SILll'face

lCenterline

surface

*For non-vented (recirculating) installations

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance "X" between the bottom of the range hood and the

cooking surface. For higher ceilings, a Stainless Steel Chimney

Extension Kit Part Number W10272075 is available from your

dealer or an authorized parts distributor. The chimney extension

replaces the upper chimney shipped with the range hood.

IMPORTANT:

Minimum distance "X": 24" (61.0 cm) from electric cooking

surface.

Minimum distance "X": 27" (68.6 cm) from gas cooking

surfaces.

Suggested maximum distance "X": 36" (91.4 cm)

For vented installations, the chimneys can be adjusted for

ceilings between 7' 11" (2.4 m) and 9' 2" (2.8 m).

For non-vented (recirculating) installations, the chimneys can be

adjusted for ceilings between 7' 11" (2.4 m) and 9' 6" (2.9 m).

Vent system must terminate to the outdoors, except for non-

vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall cap.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

The vent system must have a damper. Ifthe roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 8" (20.3 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 8" (20.3 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90° elbow may be installed immediately above the hood.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the top grille.

RoofVenting WallVenting Non-vented

(recirculating)

.......A A

B B

A. Roof cap A. Wall cap A. Deflector

B. 8" (20.3 cm) B. 8" (20.3 cm) B. 8" (20.3 cm)

round vent round vent round vent

Calculating Vent System Length

Tocalculate the length of the system you need, add the

equivalent feet (meters)for each vent piece used in the system.

Vent Piece 8" (20.3 cm) Round

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

90°o,bow wo,,c°p

The following example falls within the maximum recommended

vent length of 35 ft (10.7 m).

1 - 90° elbow

1 - wall cap

8 ft (2.4 m) straight

Length of system

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 13.0 ft (3.9 m)

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and aseparate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATION INSTRUCTIONS

It is recommended that the vent system be installed before

hood is installed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

Check your ceiling height and the hood height maximum

before you select your hood.

Disconnect power.

Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where the

canopy hood will be installed.

Select a mounting height between a minimum of 24"

(61.0 cm) for an electric cooking surface, a minimum of 27"

(68.6 cm) for a gas cooking surface, and a suggested

maximum of 36" (91.4 cm) above the range to the bottom of

the hood. Mark a reference line on the wall.

Tape template in place, aligning the template centerline and

bottom of template with hood bottom line and with the

centerline marked on the wall.

:......................................A

. i£

% i_ ii_

_EA_ _ALL

MOJ_TIN TEMPLATE

'%'F?,'_,_STM

B C

A. Centerfine

B. Fastener locations

C. Mounting height reference (hood bottom line)

Mark centers of the fastener locations through the template

to the wall.

IMPORTANT: All screws must be installed into wood. If there

is no wood to screw into, additional wall framing supports

may be required.

Remove the template.

5. Drill 3Ad'(4.8 mm) pilot holes at all locations where screws are

being installed into wood.

6. Install the 2 - 5 x 45 mm mounting screws. Leave a V4"

(6.4 mm) gap between the wall and the back of the screw

head to slide range hood into place.

(6.4 ram)

Vent Cover Bracket Installation

7. Attach vent cover bracket to wall flush to the ceiling using

2 - 5 x 45 mm screws.

A. Ceifing

B. Wall

C. Centerline

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements" section.

2. Determine the required height for the home power supply

cable and drill a 1W' (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough V2"conduit and wires from

the fused disconnect (or circuit breaker) box to make the

connection in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.

1. Using 2 or more people, hang range hood on 2 mounting

screws through the mounting slots on back of hood.

A. Mounting screws

B. Mounting slots

C. Lower mounting screws and washers

2. Remove the grease filter. See "Range Hood Care" section.

3. Level the range hood and tighten upper mounting screws.

4. Install 2 - 5 x 45 mm lower mounting screws and 2 - D6.4 x

18 mm washers and tighten.

Install transition on top of hood (if removed for shipping) with

4 - 4 x 8 mm sheet metal screws.

A. Vent transition

B. 4 x 8 mm screw (4)

For vented installations only:

1. Fit vent system over transition piece.

2. Seal connection with clamps.

3. Check that back draft dampers work properly.

For non-vented (recirculating) installation only:

1. Assemble the air deflector with the duct cover bracket with

4 assembly screws provided with the Recirculation Kit.

A. Assembly screws

B. Air deflector

C. Duct cover bracket

Measure from the bottom of the air deflector to the bottom of

the hood outlet.

E _ ,_ ,

A. Air deflector

B. Vent clamp

C. X = length to cut vent duct

D. Vent duct

E.Exhaust outlet

3. Cut the duct to the measured size (X).

4. Remove the air deflector.

5. Slide the duct onto the bottom of the air deflector.

6. Place the assembled air deflector and duct over the exhaust

outlet from the hood.

7. Reassemble the air deflector to the duct cover bracket with

4 assembly screws.

8. Seal connections with vent clamps.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box and install a UL

listed or CSA approved 1/2"strain relief.

A B

A,Knockout

B.Terminalbox

C.Terminalbox cover

Run home power supply cable through strain relief, into

terminal box.

E F

A. Home power supply cable

B. UL listed or CSA

approved strain refief

C. Black wires

D. UL listed wire connectors

E. White wires

E Green (or bare) and

yellow-green ground wires

5. Use UL listed wire connectors and connect black wires (C)

together.

6. Use UL listed wire connectors and connect white wires (E)

together.

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

7. Connect green (or bare) ground wire from home power supply

to yellow-green ground wire (F) in terminal box using UL listed

wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check that all light bulbs are secure in their sockets.

11. Reconnect power.

When using both upper and lower vent covers, push lower cover

down onto hood and lift upper cover to ceiling and install with

two 4 x 8 mm screws.

NOTE: For vented installations, the upper vent cover may be

reversed to hide slots.

A. Upper vent cover

B. Lower vent cover

C. 4 x 8 mm screws

D. Bracket

Secure the bottom of the duct with 2 - 4 x 8 mm screws.

For non-vented (recirculating) installations only, install

charcoal filters over grille on blower housing. See the "Range

Hood Care" section.

2. Install metal filters. See the "Range Hood Care" section.

3. Check the operation of the range hood blower and light. See

the "Range Hood Use" section.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the front side of the

canopy.

A. Louver holes (non-vented

[recirculating] installations only)

B. Duct covers

C. Lamp housings

D. Canopy

E. Grease filters

F. Grease filter handles

G. Control panel

Control Panel

A B

C D E

[..--

A. Power decrease C. Display

B. Power increase D. Light

E. Timer

HOOD USE

Grease Filter Saturation Alarm

After 30 hours of fan function, the display will show "Clean

Grease Filter" when the fan is active. When this icon shows in the

display, the installed grease filters should be washed. See

"Range Hood Care" section.

• To reset the grease filter saturation alarm, press and hold the

Power Increase button for 5 seconds. The "Clean Grease

Filter" icon will no longer be displayed.

Charcoal Filter Saturation Alarm

After 120 hours of fan function, the display will show "Replace

Charcoal Filter" when the fan is active. When this icon shows in

the display, the charcoal filters should be replaced. See "Range

Hood Care" section.

• To reset the charcoal filter saturation alarm, press and hold

the Power Decrease button for 5 seconds. The "Replace

Charcoal Filter" icon will no longer be displayed.

Audible Signal Activation and Deactivation

The audible signals can be activated or deactivated by pressing

the "Light" button for 5 seconds.

• If the audible signal is activated, a tone will sound, and "Snd"

symbol will appear in the display for 3 seconds.

• If the audible signal is deactivated, the "Snd" symbol will

appear on the display for 3 seconds.

Charcoal Filter (Recirculation Accessory) Inclusion

and Exclusion

When the charcoal filter is in use (recirculating mode), press and

hold the Power Decrease and Power Increase buttons at the

same time for 5 seconds. "Able" will appear in the display for

3 seconds.

If the charcoal filter is not used (vented mode), press and hold the

Power Decrease and Power Increase buttons at the same time

for 5 seconds. "None" will appear in the display for 3 seconds.

• When the charcoal filter has been excluded, the charcoal filter

alarm is disabled.

• The inclusion or exclusion of the charcoal filter must be

selected while the lights and the fan motor are Off.

HeatSensor

The control is equipped with a heat sensor that will turn on the

blower to the highest speed if excessive heat occurs around the

control area.

• If the blower is On or Off, the blower will automatically set to

the highest speed. "Auto" will appear in the display to

indicate that the heat sensor has detected excessive heat.

When the blower is operating due to excessive heat detected

by the heat sensor, the blower speed cannot be decreased.

When the temperature level on the hood drops to normal, the

blower will return to its setting before the excessive heat was

sensed.

To operate the light:

1. Press the Light button to turn the light on to high.

2. Press the Light button again to turn the light to low.

3. Press the Light button a third time to turn the light off.

The timer can be set from 1 to 60 minutes. The default timer

setting is 10 minutes.

To use the timer:

1. Press the Timer button to enter the timer mode. After

5 seconds, the default time will be automatically selected.

2. Press the Power Decrease and Power Increase buttons while

the display is flashing (5 seconds) to adjust to the desired

time. Pressing the timer button again or waiting 5 seconds

after selecting the desired time will start the timer countdown.

3. The timer can be canceled at any time by pressing the Timer

button again.

NOTE: During the timer setup, the Power Decrease and Power

Increase buttons are dedicated to the timer. After the timer starts,

the Power Decrease and Power Increase buttons can be used for

other functions.

Power Increase/On

This button is used to turn the fan On or increase the fan speed.

• The fan will turn On if the Power Increase button is pressed

and the hood was Off.

• An audible tone will sound when the fan reaches its highest

speed.

Power Decrease/Off

• This button is used to turn the fan Off or to decrease the fan

speed.

RANGE HOOD CARE

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

• Liquid detergent soap and water, or all-purpose cleanser

• Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filter

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Let filter dry thoroughly before replacing it.

Turn off fan and lights. Allow halogen lamp to cool.

1. Remove each filter by pulling the spring release handle and

then pulling down the filter.

A. Spring release handle

Wash metal filters as needed in dishwasher or hot detergent

solution.

Reinstall the filter by making sure the spring release handles

are toward the front. Insert metal grease filter into upper

track.

4. Pull the spring release handle down.

5. Push up on metal filter and release handle to latch into place.

6. Repeat steps 1-5 for the other filter.

Non-Vented (recirculating) Installation Filters

The charcoal filter is not washable. It should last up to 6 months

with normal use. Replace with Charcoal Filter Kit Number

W10272068.

To replace charcoal filter:

1. Cover the grille that covers the blower motor with the

charcoal filter so that the slots on the filter correspond to the

pins on the sides of the motor grille.

A B C

A. Charcoal filter

B. Pins

C. Blower motor

2. Turn the charcoal filter clockwise to lock it.

3. Repeat steps 1-2 on the other filter.

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new lamp, do not

touch lamp with bare fingers. Replace lamp, using tissue or

wearing cotton gloves to handle lamp.

If new lights do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Use a flat-blade screwdriver and gently pry the light cover

loose.

3. Remove the lamp and replace with a 120-volt, 40-watt

maximum, halogen lamp made for a G-9 base.

4. Replace the light cover.

5. Reconnect power.

WIRING DIAGRAM

GND

(

Y/G Bt< W

Motor Specifications

PowerSupply 120VAC

Frequency 60 HZ

PowerAbsorption 450W

Current 3.7A

Motor Resistance (Ohms)

Blue- Black 9.8

Blue- Gray 14.3

Blue- Red 18

Blue- White 21.6

RoomTemp. 73.4°F(23°0)

4 Lamps only on

Island Versions

( V I _1

1---4 '---4

I J

_,1,- J,,_ ! I

",*" "_° '< .... I_"

ElectronicUserInterface

ElectronicPowerBoard

W BK BL

L NL NM

P2 P4A P3 P4

2 11

.... J

'16

LA S4 S3 S2 S1

P5 P9 P8 P7 P6

Y/G

SEI24A

ASSISTANCE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

Call the dealer from whom your appliance was purchased, or call

1-800-JENNAI£ (1-800-536-6247} to locate an authorized

service company. When calling, please know the purchase date

and the complete model and serial number of your appliance. Be

sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-536-6247

U.S. customers using -i-i-Y for deaf, hearing impaired or speech

impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. -

8:00 p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Center.

OR SERVICE

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10272068

Recirculation Kit

(for non-vented installations only)

Order Part Number W10272060

Chimney Extension Kit

Order Part Number W10272075

6" (15.2 cm) Makeup Air Kit

(consult local building codes)

Order Part Number W10446915

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-536-6247 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave

Mississauga, ON L5N 0B7

Web address: www.jennair.ca

Or call: 1-800-536-6247.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Centre.

JENN-AIR®MAJOR APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions

attached to or furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will

pay for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major

appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Jenn-Air designated service company. This limited warranty is valid only in the United States or Canada

and applies only when the major appliance is used in the country in which it was purchased. Outside the 50 United States and Canada,

this limited warranty does not apply. This limited warranty is effective from the date of original consumer purchase. Proof of original

purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products including but not limited to consumables or cleaning products not

approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Replacement parts or repair labor for major appliances with original model/serial numbers that have been removed, altered or

cannot be easily determined. This warranty is void if the factory applied serial number has been altered or removed from your major

appliance.

12. Removal or replacement of trim, decorative panels, flooring, cabinetry, islands, countertops, drywall or other built-in fixtures that

interfere with servicing, removal or replacement of the product.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty

gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling us at 1-800-JENNAIR (1-800-536-6247). 2/13

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SEOURITE DE LA HOWE DE OUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s@curit@importants dans ce manuel et sur votre appareil m@nager. Assurez-vous de

toujours lire tousles messages de s@curit@et de vous y conformer.

Voici le symbole d'alerte de s@curit@.

Ce symbole d'alerte de s@curit@vous signale les dangers potentiels de d@c@set de blessures graves a vous

et _td'autres.

Tousles messages de s@curit_ suivront le symbole d'alerte de s@curit@et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s@curit@vous diront quel est le danger potentiel et vous disent comment r@duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Avertissements de la proposition 65 de I'¢:tat de Californie "

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour @re a I'origine de

cancers.

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour @re a I'origine de

malformations et autres d6ficiences de naissance.

llVIPORTANTES iNSTRUCTiONS DE Sl CURITl

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommag6(e). Jeter le ventilateur ou le retourner

& un centre de service agr66 pour examen et/ou r6paration.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil a gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de per£age dans un mur

ou un plafond, veiller a ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air a I'ext6rieur.

MISE EN GARDE : Cet appareil est con£_uuniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'& I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R}_DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MC:TALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE :

=1Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

=1Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

=1Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

=1Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR RC:DUIRE LE RISQUE DE

DOMMAGES CORPORELS APR_:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

=1Placer sur le r6cipient un couvercle bien ajust6, une t61e&

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brOleur. VEILLER ,&.¢:VITER

LES BRULURES. Si les flammes ne s'6teignent pas

imm6diatement, CVACUER LA PIECE ET APPELER LES

POMPIERS.

=1NE JAMAIS PRENDRE EN MAIN UN R¢:CIPIENT

ENFLAMMI 2 - vous risquez de vous brOler.

=1NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brOlante.

=1Utiliser un extincteur SEULEMENT si :

- II s'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- II s'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar6.

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

m AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

LIRE ET CONSERVER CES INSTRUCTIONS

EXIGENCES D'INSTALLATION

Rassembler les outils et pieces necessaires avant d'entreprendre

I'installation. Lire et observer les instructions fournies avec

chacun des outils de la liste ci-dessous.

Outils n_cessaires

• Niveau

• Perceuse avec des forets de 11¼"(3 cm), 3/8"(9,5 mm) et sad'

(7,9 mm)

• Crayon

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet &calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides deserrage

• Scie sauteuse ou scie & guichet

• Tournevis & lame plate

• Cisaille de ferblantier

• Tournevis Phillips

Pi_ces n_cessaires

• C&ble d'alimentation electrique du domicile

• Serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)

• 3 connecteurs de ills homologues UL

Pour les installations avec d_charge a I'ext_rieur, il faudra

aussi :

• 1 bouche de decharge (decharge & travers lemur ou &travers

le toit)

• Circuit d'evacuation metallique

Pour les installations sans d_charge a I'ext_rieur (recyclage),

il faudra aussi :

• Ensemble de recyclage, piece numero W10272060 pour les

installations sans decharge & I'exterieur (recyclage)

uniquement. Voir la section "Assistance ou service" pour

commander.

• Conduit d'evacuation metallique circulaire de 8" (20,3 cm) de

diametre - Iongueur necessaire determinee par la hauteur de

plafond.

Pi_ces fournies

Retirer les pieces de leur emballage. Verifier que toutes les

pieces sont presentes.

• Auvent de hotte avec ventilateur et lampes installes

• Raccord de transition avec clapets anti-reflux installes

• Filtre(s) a graisse metallique(s) - selon le modele et la taille

• Bride de support du cache-conduit

• Gabarit de montage

• Cache-conduit - 2 pieces

• 8visde4x8mm

• 6 vis de montage de 5 x 45 mm

• 2 rondelles D6,4 x 18 mm

• 2 chevilles d'ancrage mural de 8 x 40 mm

• 4 chevilles d'ancrage mural de 10 x 50 mm

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est

I'installateur qu'inoombe la responsabilite de respecter les

distances de separation specifiees sur la plaque signaletique de

I'appareil. La plaque signaletique de I'appareil est situee derriere

le filtre de gauche, sur la paroi arriere de la hotte.

On doit toujours installer la hotte & distance des sources de

courant d'air (fen6tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures &

decouper dans les placards. Ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

On doit disposer d'une prise de courant electrique reliee & la

terre. Voir la section "Specifications electriques".

La hotte est configuree & I'usine pour une decharge & travers le

toit ou un mur. Pour une installation sans decharge & I'exterieur

(recyclage), voir "Installations sans decharge a I'exterieur

(recyclage) uniquement", & la section "Raccordement du circuit

d'evacuation". L'ensemble de recyclage (piece numero

W10272060) est disponible chez votre marchand ou chez un

distributeur de pieces autoris&

On doit assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond et le mur oQla hotte sera installee.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups)ANSI A225.1/NFPA 501A, ou des codes Iocaux.

Dimensions du produit

103A'' (27 4%" (11,7 cm)

7_%d' (20,2 cm)

*28%d' (71,9 crn) rnin.

42%" (108,3 cm) max.

24"cm )

**24%" (62,5 crn) rain.

ore) max.

30" (7_

36" (91,4 cm). 12 7

42" (106,7 crn)_/...j_ _ ( ,

--_ _V_d' (50,0cm)

*Installations sans decharge & I'exterieur (recyclage)

**Installations avec decharge & I'exterieur

Dimensions du placard

10" (25,4 crn) rnin.

13" (33,0 max.

2" (5,1 crn) rain.

,9 crn) rnin.

PJacard

adjacent

Point d'entr_e

10"(25,4 crn) rnin. du circuit

13"(33,0 et du c_bie

d'alimentation

.............!...........i, 61ectrique

/ j 17" (43,2 crn)*

4_ S"

/°° J Placard

.............................i......................i adjacent

30" (76,2

36" (91,4 crn) ou

42" (106,7 crn)

Distance "X" I

entre le bas de

I'auvent et la !

surface de cuisson I,

jAxe central

Surface de cuisson

*Installations sans decharge a I'exterieur (recyclage)

*REMARQUE • Les cache-conduits de hotte sont reglables; on

peut les ajuster en fonction de la hauteur disponible sous

plafond ou soffite, selon la distance "X" entre le bas de la hotte

et la surface de cuisson. Pour des plafonds de hauteur

superieure, un ensemble de cache-conduit en acier inoxydable,

piece numero W10272075 est disponible chez votre marchand

ou chez un distributeur de pieces autoris& L'extension de

cache-conduit remplace la section superieure du cache-conduit

fournie avec la hotte.

IMPORTANT :

Valeur minimale de la distance "X" : 24" (61,0 cm) a partir de

la surface de cuisson electrique.

Distance minimale "X" : 27" (68,6 cm) a partir d'une surface

de cuisson au gaz.

Distance maximale "X" sugger6e : 36" (91,4 cm)

Pour les installations avec decharge &I'exterieur, on peut ajuster

les cache-conduits pour une hauteur sous plafond de 7' 11"

(2,4 m) et 9' 2" (2,8 m).

Pour une installation sans decharge & I'exterieur (recyclage), on

peut ajuster les cache-conduits pour une hauteur sous plafond

entre 7' 11" (2,4 m) et 9' 6" (2,9 m).

_}_ ext6_ eu_ _'

• Le circuit d'evacuation doit decharger I'air &I'exterieur,

excepte pour une installation sans decharge & I'exterieur

(recyclage).

Ne pas terminer le circuit d'evacuation dans un grenier ou

dans un autre espace ferm&

Ne pas utiliser une bouche de decharge murale de 4"

(10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser uniquement du conduit metallique. Le conduit en

metal rigide est recommande. L'utilisation d'un conduit en

plastique ou en alumimium n'est pas recommandee.

• La Iongueur du circuit d'evacuation et le nombre de coudes

doit _tre reduit au minimum pour fournir la meilleure

performance.

Pour un fonctionnement efficace et silencieux :

• Ne pas utiliser plus de trois coudes & 90°.

• Veiller & ce qu'il y ait une section droite de conduit de 24"

(61,0 cm) ou plus entre deux coudes, si on doit utiliser plus

de un raccord coud&

Ne pas connecter 2 coudes ensemble.

Au niveau de chaque jointure du circuit d'evacuation, assurer

I'etanch6it6 avec des brides de serrage pour conduit.

Le circuit d'evacuation doit comporter un clapet anti-reflux. Si

la bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec lahotte

d'extraction.

• Autour de la bouche de decharge &I'exterieur (mur ou toit),

assurer I'etancheite avec un compose de calfeutrage.

• La taille du conduit doit _tre uniforme.

Installation dans une r_gion & climat froid

On doit installer un clapet anti-reflux additionnel pour minimiser

le reflux d'air froid, et incorporer un element d'isolation thermique

pour minimiser la perte de chaleur par conduction par

I'intermediaire du conduit d'evacuation, de I'interieur de la

maison & I'exterieur. Le clapet anti-reflux doit _tre place du c6te

froid par rapport & I'element d'isolation thermique.

L'element d'isolation thermique doit _tre aussi proche que

possible de I'endroit oQ le circuit d'evacuation penetre la partie

chauffee de la maison.

Air d'appoint

Le code du b&timent local peut exiger I'emploi d'un systeme de

renouvellement de I'air/introduction d'air d'appoint, Iors de

I'utilisation d'un systeme d'aspiration de debit superieur & une

valeur (pieds cubes par minute) specifiee. Le debit specifie, pieds

cubes par minute, est variable d'une juridiction &une autre.

Consulter un professionnel des installations de chauffage

ventilation/climatisation au sujet des exigences specifiques

applicables dans la juridiction locale.

M_thodes d'_vacuation

Cette hotte a ete configuree & I'usine pour la decharge de I'air

aspire a travers le toit ou & travers un mur.

Un circuit d'evacuation en conduit rond de 8" (20,3 cm) (non

fourni) est necessaire pour I'installation. La hotte comporte une

ouverture de sortie de diam_tre 8" (20,3 cm).

REMARQUE : On deconseille I'emploi de conduit flexible. Un

conduit flexible peut causer une retropression et des turbulences

de I'air, ce qui reduit considerablement la performance.

La sortie & I'exterieur du circuit d'evacuation peut se faire &

travers le toit ou & travers un mur. Pour la sortie a travers un mur,

on doit employer un raccord coude (90°).

D_charge par I'arri_re

Le raccord coude a 90 ° peut _tre installe immediatement au-

dessus de la hotte.

La page charge ...

Jenn-Air JXW8030WS0 Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW8030WS0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JXW8030WS0 Owner's manual

Jenn-Air JXW8030WS0 Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JXW8030WS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents