Insignia Flat Panel Television NS-27LCD Manuel utilisateur

27" LCD TV | TV ACL de 27 po | TV LCD de 27"

NS-27LCD

3

www.insignia-products.com

Insignia NS-27LCD

27” LCD TV

Contents

Safety information . . . . . . . . . . . . . . . . . . . . . . . . .3

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . . .7

Using your TV . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Programming the remote control . . . . . . . . . . . . .16

Maintaining. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .18

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Legal notices . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Français. . . . . . . . . . . . . . . . . . . . . . . . 23

Español . . . . . . . . . . . . . . . . . . . . . . . . 44

Safety information

Read instructions

Read all of the safety and operating instructions

before you use your TV.

Retain instructions

Retain safety and operating instructions for

future reference.

Follow warnings and instructions

Follow all warnings on your TV and in the

operating instructions. Follow all operating and

use instructions.

Water and moisture

Do not use your TV near water. For example, do

not use it near a bath tub, wash bowl, kitchen

sink, or laundry tub, in a wet basement, or near a

swimming pool.

Cleaning

Unplug your TV before cleaning. Do not use

liquid or aerosol cleaners. Use only a damp cloth

to clean the exterior of your TV.

Ventilation

Slots and openings in the cabinet and the back

or bottom are provided for ventilation, reliable

operation, and protection from overheating.

These openings must not be blocked or covered.

Do not block the openings by placing your TV on

a bed, sofa, rug, or other similar surface. Do not

place your TV near or over a radiator or heat

register. Do not place your TV in a built-in

installation, such as a bookcase or rack, unless

you provide correct ventilation or follow the

manufacturer’s instructions.

Heat

Make sure that your TV is located away from

heat sources such as radiators, heat registers,

stoves, or other products (including amplifiers)

that produce heat.

Grounding or polarization

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A

grounding type plug has two blades and a

grounding prong. The wide blade or grounding

prong are provided for your safety. If the plug

does not fit, contact an electrician to replace the

obsolete outlet.

Power cord protection

Route power cords so that they are not likely to

be walked on or pinched by items placed on or

against them. Pay particular attention to cords at

plugs, convenience receptacles, and the point

where they exit from your TV.

Attachments

Do not use attachments not recommended by

Insignia because they may cause hazards.

Stand

Do not place your TV on an unstable cart, stand,

tripod, bracket, or table. Your TV may fall,

causing serious personal injury and serious

damage to your TV. Use only with a cart, stand,

tripod, bracket, or table recommended by the

manufacturer, or sold with your TV. If you mount

your TV to the wall, follow the manufacturer’s

instructions and use a mounting accessory

recommended by the manufacturer. Your TV and

cart combination should be moved with care.

Quick stops, excessive force, and uneven

surfaces may cause your TV and cart

combination to overturn.

Lightning

For added protection for your TV’s receiver

during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the power outlet and disconnect

the antenna or cable system. This helps prevent

damage to your TV from lightning and power line

surges.

Warning

To reduce the risk of electric shock, do not remove the cover or

back. No user serviceable parts inside. Refer servicing to

qualified service personnel.

To reduce the risk of fire or electric shock, do not expose your

TV to rain or moisture.

Caution

To prevent electric shock, match the wide blade on the power

cord plug to the wide slot on an electric outlet. If the plug does

not fit, consult a licensed electrician to replace the obsolete

outlet. Do not modify the power cord plug, or you will defeat

this safety feature.

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present

within your TV. This label is located on the back

of your TV.

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying your TV.

Warning

Your TV contains tin-lead solder and a fluorescent lamp

containing a small amount of mercury. Disposal of these

materials may be regulated for environmental reasons. For

disposal or recycling information, contact your local authorities

or the Electronic Industries Alliance at www.eia.org.

4

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Servicing

Do not attempt to service your TV yourself

because opening or removing covers may

expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service

personnel.

Replacement parts

When replacement parts are required, make

sure that the service technician uses

replacement parts specified by the manufacturer

that have the same characteristics as the

original part. Unauthorized substitutions may

result in fire, electric shock, personal injury, or

other hazards.

Overloading

Do not overload power outlets and extension

cords because this can result in a risk of fire or

electric shock.

Object and liquid entry

Never push objects of any kind into your TV

through openings because objects may touch

dangerous voltage points or short out parts that

could result in a fire or electric shock. Never spill

liquid of any kind on your TV.

Damage requiring service

Unplug this TV from the power outlet and refer

servicing to qualified service personnel under

the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled or objects have

fallen into your TV.

• If your TV has been exposed to rain or water.

• If your TV does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the

operating instructions because incorrect

adjustment of other controls may result in

damage and will often require extensive work

by a qualified technician to restore your TV to

its normal operation.

• If your TV has been dropped or damaged in

any way.

• When your TV exhibits a distinct change in

performance.

Replacement parts

When replacement parts are required, make

sure that the service technician uses

replacement parts specified by the manufacturer

that have the same characteristics as the

original part. Unauthorized substitutions may

result in fire, electric shock, personal injury, or

other hazards.

Safety check

After completing any service or repair to this TV,

ask the service technician to perform routine

safety checks to determine that your TV combo

is in correct operating condition.

Power source

Operated your TV only from the type of power

source indicated on the marking label. If you are

not sure of the type power supplied to your

home, consult your TV dealer or local power

company.

Lightning

For added protection for your TV’s receiver

during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the power outlet and disconnect

the antenna or cable system. This helps prevent

damage to your TV from lightning and power line

surges.

Screen protection

Your TV’s screen is made of glass. Do not drop

your TV or hit the glass screen. If the screen

breaks, be careful of broken glass.

Pixel defect

Your TV’s screen is designed to display finely

detailed pictures. Occasionally, a few non-active

pixels may appear on the screen as fixed points

of blue, green, or red. This is not a defect and

does not affect your TV’s performance.

Outdoor antenna grounding

If an outside antenna or cable system is

connected to your TV, make sure that the

antenna or cable system is grounded to provide

some protection against voltage surges and

built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA No. 70,

provides information with respect to correct

grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors,

location of the antenna-discharge unit,

connection to grounding electrodes, and

requirements for the grounding electrode.

Note to CATV system installer

This reminder is provided to call the CATV

system installer’s attention to Article 820-40 of

the NEC that provides guidelines for correct

grounding and in particular, specifies that the

cable ground must be connected to the

grounding system of the building as close to the

point of cable entry as practical.

1 Electric service equipment

2 Power service grounding electrode

system

3 Ground clamps

4 Grounding conductors

5 Antenna discharge unit

6 Grounding clamp

7 Antenna lead-in wire

6

7

5

2

1

3

4

5

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Features

Front

Side

Back jacks

Control Description

1 Power indicator Lights when your TV is turned on.

2 Remote sensor Receives signals from the remote

control.

Control Description

1 CH+/CH– Press to change the channel.

In the on-screen menu system, press

to select menus and options.

2 VOL+/VOL– Press to increase or decrease the

volume.

In the on-screen menu system, press

to adjust a setting or change a value.

3 MENU Press to open the on-screen menu

system.

4 INPUT Press to select the video input.

5 Power Press to turn your TV on or off.

Jack

1S/PDIF

2HDMI

3 D-SUB AUDIO input

4 D-SUB PIC (video) input

5 COMPONENT INPUT Y

6 COMPONENT INPUT Cb/Pb

7 COMPONENT INPUT Cr/Pr

8 COMPONENT INPUT R AUDIO

9 COMPONENT INPUT L AUDIO

10 RF (antenna input)

11 S-VIDEO

12 AV INPUT VIDEO

13 AV INPUT L AUDIO

14 AV INPUT R AUDIO

Remove the

jack cover

Remove

the jack

cover

6

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Remote control

15 HEADPHONE

16 AV OUT R AUDIO

17 AV OUT L AUDIO

18 AV OUT VIDEO

19 RS232 control interface

Note

This remote control is a universal remote control. If it does not

seem to work with your TV, press the TV button.

Note

For instructions on programming the remote control, see

“Programming the remote control” on page 16.

Button Description

1 SET Press to program the remote

control. For more information,

see “Programming the remote

control” on page 16.

Jack

MTS/SAP ZOOM CCD SLEEP

AUDIO

PICTURE

FREEZE

1

2

3

4

5

6

7

19

8

20

9

21

10

11

22

23

13

12

25

24

15

14

27

26

28

29

16

17

18

30

2 Device buttons TV–Press to select the TV.

DVD–Press to select a connected

DVD player.

CBL–Press to select cable or

satellite TV.

AUX–Press to select a device

assigned to this button.

3 Number buttons Press to enter channel numbers.

In the on-screen menu system,

press to enter your parental

controls password.

4 INPUT Press to select the video input.

5 Press to go to last viewed

channel.

6 + CH – Press to change TV channels.

7 MUTE Press to mute the sound.

8 MENU Press to open the on-screen

menu system.

9

OK

Press the arrows to move down,

up, left, or right in the on-screen

menu system.

Press the OK button to confirm

changes or to toggle options on

and off in the on-screen menu

system.

10

When playing a DVD, press to

freeze the screen image. Press

again to unfreeze the image.

11 Press to start a recording on a

connected device, such as a VCR.

12 Press to fast-reverse on a DVD or

CD if a DVD or CD player is

connected.

13

Press to skip the previous chapter

on a DVD or previous track on a

CD if a DVD or CD player is

connected.

14 MTS/SAP Press to select one of the preset

audio modes. You can select

MONO, STEREO, or SAP.

15 ZOOM Press to select the aspect ratio.

16 Press to turn on your TV or put it

into Standby mode.

17 LED Lights when you are

programming the remote control.

For more information, see

“Programming the remote

control” on page 16.

18 — Press to select a sub-channel. For

more information, see “Selecting

a digital sub-channel” on page 13.

19 + VOL – Press to adjust the volume.

20 INFO Press to display status

information.

21 EXIT Press to close the on-screen

menu system.

22 Press to start DVD or CD playback

if a DVD or CD player is

connected.

23 Press to stop DVD or CD playback

if a DVD or CD player is

connected.

Button Description

7

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Using the remote control

To use the remote control:

• Point the remote control towards the remote

sensor on the front of your TV.

The following illustration shows the remote

control range.

Setting up your TV

Installing remote control batteries

To install the remote control batteries:

1 Remove the battery cover.

2 Insert two AA batteries into the battery

compartment. Make sure that you match the

+ and – symbols on the batteries with the +

and – symbols in the battery compartment.

3 Replace the cover.

Connecting your TV to an electrical outlet

To connect your TV to an electrical outlet:

• Plug the power cord into an electrical

outlet.

24 Press to fast-forward on a DVD or

CD if a DVD or CD player is

connected.

25

Press to skip the next chapter on

a DVD or next track on a CD if a

DVD or CD player is connected.

26 SLEEP Press to set the sleep timer. For

more information, see “Setting

the sleep timer” on page 14.

27 CCD Press to turn closed captions on

and off. For more information, see

“Viewing closed captions” on

page 14.

28 PICTURE Press to select the picture mode.

29 FREEZE Press to freeze the video image.

Press again to unfreeze the

image. Do not freeze the video

image for long periods of time.

You may damage the TV screen.

30 AUDIO Press to select the sound mode.

Notes

• Do not expose the remote control to shock or liquids.

• Do not use the remote control in an area with high humidity.

• Do not place the remote control in direct sunlight.

• Do not place objects, such as furniture, between the remote

control and the remote sensor.

• The remote control may not work if direct sunlight or bright

light shines on the remote sensor. Either move your TV or

change the angle at which you use the remote control.

Button Description

DISPLAY ASPECT CAPTION SLEEP

STEREO SRS

SOUND MODE

PICTURE MODE

PIP SIZE TV/PC PIP INPUT

30

0

30

0

60°

16.4 ft.

(5 m)

Notes

• Do not mix batteries of different types.

• Do not mix old and new batteries.

• Remove batteries when the charge is depleted.

• Battery chemicals can cause a rash. If the batteries leak,

clean the battery compartment with a cloth. If chemicals

touch your skin, wash immediately.

• If the remote control is not going to be used for an extended

period of time, remove the batteries.

Notes

• Make sure that you use the correct type of power. See the

label on your TV.

• If you do not intend to use your TV for an extended period of

time, unplug the power cord from the electrical outlet.

8

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Connecting speakers

To connect speakers to your TV:

1 Unplug the TV power cord and all devices

connected to your TV.

2 Connect the speakers to the speaker jacks

on the back of your TV. Make sure that you

connect the black part of the speaker wire to

the – jack and the red part of the speaker

wire to the + jack on the back of your TV.

Connecting an outside antenna

Antenna cables come in two types: 75 ohm and

300 ohm.

If your antenna cable has a 75 ohm connector,

connect the cable to the coaxial jack on the back

of your TV.

If your antenna cable has a 300 ohm connector,

connect the cable to a 300-75 ohm adapter (not

included), connect the adapter to a 75 ohm

cable, then connect the other end of the 75 ohm

connector to the coaxial jack on the back of your

TV.

Use the following illustration to connect an

outside antenna.

Connecting cable TV

Your TV has a 75 ohm jack for connecting cable

TV.

Some cable TV providers scramble the signals

for “premium” (pay) channels. To view these

channels you need a converter/descrambler box.

If you do not have a converter/descrambler box,

you can connect your cable TV directly to your

TV. If you have a converter/descrambler box, you

can connect your cable TV using an RF switch

(not supplied). For more information about

connecting a converter/descramble box, contact

your cable TV provider.

To connect cable TV without a

converter/descrambler box:

1 Connect one end of a 75 ohm cable to the

coaxial jack on the back of your TV.

2 Connect the other end of the cable to the

cable TV wall outlet.

Note

The location of the speaker jacks on your TV may

vary from the illustration.

Black

Red

Right speaker Left speaker

Black Red

75 ohm cable

300-ohm cable

VHF/UHF

antenna

300-ohm cable

with adapter

OR

VHF/UHF

antenna

75-ohm

cable

Antenna

cable

OUT

IN

Combiner

OR

UHF

antenna

VHF

antenna

Separate antennas

Combination antenna

9

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

To connect cable TV with a

converter/descrambler box:

• Use the following illustration to connect a

converter/descrambler box. (The RF switch

and the signal splitter are not provided.)

Set the RF switch to the A position to watch

unscrambled channels using your TV remote

control. Set the RF switch to the B position to

watch scrambled channels using the

converter/descrambler controls.

Connecting a sound system

Use the following illustration to connect an audio

processor or Hi-Fi system.

Connecting a VCR

You can connect a VCR with a standard

audio/video cable or with a S-Video cable. The

S-Video cable does not carry sound. If you use

an S-Video cable, you need to use an audio

cable to connect sound.

Use the following illustration to connect a VCR.

To play the VCR:

1 Turn on your TV.

2 Press the INPUT button one or more times to

select Composite1 (or S-Video if you

connected the VCR to the S0-Video jack).

3 Turn on your VCR.

4 Insert a videotape, then press the PLAY

button.

Warning

Make sure that you turn off and unplug your TV before

installing devices.

Note

For home theater systems, use an S/PDIF cable to achieve full

sound capabilities.

RF switch

Cable converter/descrambler box

Two-set signal

splitter

Out

In

A

B

S/PDIF cable

S/PDIF IN jack

Audio processor

Hi-Fi system

Note

For better video, use the S-Video jack if your VCR has an

S-Video connection.

Warning

Make sure that you turn off and unplug your TV before

installing devices.

S-VIDEOANT OUT ANT IN

VIDEO L- AUDIO - R

Y

W

R

OR

S-Video cable

Audio cable

Video cable

Y=yellow (video)

W=white (audio left)

R=red (audio right)

TV

VCR

10

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Connecting a VCR (for recording)

Use the following illustration to connect a VCR

for recording TV programs.

To record a program:

1 Turn on your TV.

2 Select a program you want to record.

3 Turn on the VCR.

4 Insert a videotape, then press the record

button on the VCR.

Connecting an amplifier

Use the following illustration to connect an

external amplifier.

Warning

Make sure that you turn off and unplug your TV before

installing devices.

S-VIDEOANT OUT ANT IN

VIDEO L- AUDIO - R

Y

W

R

TV

VCR

Y=yellow (video)

W=white (audio left)

R=red (audio right)

Video cable

Audio cable

W

R

TV

Amplifier

Audio cable

W=white (audio left)

R=red (audio right

11

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Connecting a camcorder

Use the following illustration to connect a

camcorder to your TV.

To connect a camcorder:

1 Plug the audio/video cable into the AUDIO L,

AUDIO R, and VIDEO jacks ont the back of

your TV.

2 Plug the other end of the audio/video cable

into the audio and video out jacks on the

camcorder.

To playback from the camcorder:

1 Turn on your TV.

2 Press the INPUT button one or more times to

select Composite2.

3 Turn on the camcorder, then set it to output

mode. See your camcorder documentation

for more information.

4 Insert a tape into the camcorder, then press

the Play button.

Connecting a DVD player

Use the following illustration to connect a DVD

player to your TV.

To connect a DVD player:

• Plug the HDMI cable into the HDMI jack

on the back of your TV and to the HDMI

out jack on the back of the DVD player.

To play a DVD:

1 Turn on your TV.

2 Press the INPUT button one or more times to

select HDMI.

3 Turn on the DVD player.

4 Insert a DVD, then press the Play button.

Warning

Make sure that you turn off and unplug your TV before

installing devices.

VIDEO L- AUDIO - R

Y

W

R

TV

Y=yellow (video)

W=white (audio left)

R=red (audio right)

Video cable

Audio cable

Camcorder

OUT IN

Warning

Make sure that you turn off and unplug your TV before

installing devices.

Note

If the DVD player has DVI output only, use a DVI to HDMI

adapter cable (not supplied) to connect the DVD player to the

HDMI jack on the back of your TV. Then connect the audio

cable to the D-SUB AUDIO IN jack on the back of your TV.

TV

DVD player

HDMI

Output

12

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Connecting a DTV receiver

To watch your DTV:

1 Turn on your TV.

2 Press the INPUT button one or more times to

select Component1.

3 Turn on your DTV receiver.

Connecting a computer

Use the following illustration to connect a

computer to your TV.

To watch TV on your computer monitor:

1 Turn on your TV.

2 Press the INPUT button one or more times to

select VGA.

3 Turn on your computer, then set up your

computer for external VGA input. See your

computer documentation for more

information.

Using your TV

Turning your TV on and off

To turn on your TV:

1 Make sure that the power cord is connected

to your TV and an electrical outlet.

2 Press the button to turn on your TV.

3 Press the button again to turn off your TV

Selecting the TV source

To select the TV source:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Setup, then press the OK or

button to open the Setup menu.

3 Press the or button one or more times

to highlight Tuning Band, then press the OK

or button to access the tuning band

options.

Warning

Make sure that you turn off and unplug your TV before

installing devices.

G

W

RBR

S-VIDEO

ANT IN

L - AUDIO - R VIDEO

DVI

L - AUDIO - R

AUDIO

AV OUT

COMPONENT

G=green (Y)

W=white (audio left)

R=red (audio right, Cr.Pr)

B=blue (Cb/Pb)

TV

DTV receiver

Audio cable

Video cable

Warning

Make sure that you turn off and unplug your TV before

installing devices.

D SUB cable

Audio cable

TV

Computer

13

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

4 Select Air for an outside antenna. Select

Cable, Cable HRC, Cable IRC, or Cable

Auto for cable TV. We recommend that you

select Cable Auto for cable TV. For more

information about cable TV selections,

contact your cable TV provider.

5 Press the EXIT button to close the on-screen

menu system.

Setting up the channel list

After you select your TV source (antenna or

cable), you need to set up the channel list. When

you set up your channel list, your TV searches

for all available channels in your area and stores

a list of the channels. When your press the

CH – or + button, your TV skips the channels

that do not have a signal.

Automatically setting up channels

To automatically set up the channel list:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Setup, then press the OK or

button to open the Setup menu.

3 Press the or button one or more times

to highlight Auto Ch Search.

4 Press the OK or button to start the search.

Manually adding or deleting channels from

the channel list

After you create a channel list using the Auto Ch

Search option, you can manually add or delete

channels from the channel list.

To add or delete channels:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Setup, then press the OK or

button to open the Setup menu.

3 Press the or button one or more times

to highlight Manual Ch Set, then press the

OK or button to access the Manual Ch Set

options.

4 Press the or button to select a channel,

then press the OK button to add or delete a

channel.

5 Press the EXIT button to close the menu.

Changing channels

To change channels:

• Press the CH – or + button on the remote

control to go to the next lower or higher

channel.

Or

Press the number buttons to select a

channel. For example, if you want channel

83, press 8, then press 3.

Or

Press the button to go to the last viewed

channel.

Selecting a digital sub-channel

Most digital TV channels have more than one

channel. The main channel carries the signal for

the main TV program. The sub-channels carry

signals for additional or alternate programming,

such as a radio or news broadcast.

For example, if the main channel number is 8,

the sub-channel number might be 8-1, 8-2, and

8-3,

To select a sub-channel:

1 Press the number buttons for the main

channel, for example 8.

2 Press the – button, the press the sub-channel

button, for example 1.

Adjusting the volume

To adjust the volume:

• Press the VOL – or + button to decrease or

increase the volume.

• Press the MUTE button to turn off the sound.

Press the MUTE button again to turn the

sound back on.

Displaying status information

To display status information:

• Press the INFO button. Your TV displays

status information, such as the channel

number or signal source.

Selecting the video input source

To select the video input source:

• Press the INPUT button one or more times to

select the video source. You can select:

• TV–TV signal

• Composite1–AV INPUT1 jacks

• Composite2–AV INPUT2 jacks

• Component1–COMPONENT INPUT1

jacks

• Component2–COMPONENT INPUT2

jacks

• VGA–D-SUB jack (computer)

• HDMI–HDMI jack

• S-Video–S-Video jack

Checking the DTV signal strength

To check the DTV signal strength:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Setup, the press the OK or

button to open the Setup menu.

3 Press the or button one or more times

to highlight DTV Signal, then press the OK

or button. Your TV shows the DTV signal

strength.

Adding a channel label

To add a label to a channel:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Setup, then press the OK or

button to open the Setup menu.

Note

You can press the Exit button to stop the search.

14

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

3 Press the or button one or more times

to highlight Channel Labels, then press the

OK or button to open the Channel Labels

Menu.

4 Press the or button to move the highlight

or cursor. Press the or button to toggle

between NTSC or ATSC or to select a

channel number or character.

5 Press the OK button to return to the previous

menu or press the EXIT button to close the

menu system.

Freezing the picture

You can freeze (still) the screen image.

To freeze or unfreeze the picture:

• Press the FREEZE button.

Setting the clock

You can automatically set the clock from a digital

channel signal. Your TV searches for a digital

channel that has time information encoded. If the

clock is not correct after you automatically set it,

you can manually set the clock.

Automatically setting the clock

To automatically set the clock:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Feature, then press the OK or

button to open the Feature menu.

3 Press the or button one or more times

to highlight Time Set, then press the OK or

button to open the Time Set menu.

4 Press the or button one or more times

to highlight Time Set Mode, then press the

OK or button to select Auto.

5 Press the or button one or more times

to highlight Time Zone, then press the OK or

button to select a time zone: Pacific,

Alaska, Hawaii, Eastern, Central, or

Mountain.

6 Press the EXIT button to close the on-screen

menu system.

Manually setting the clock

To manually set the clock:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Feature, then press the OK or

button to open the Feature menu.

3 Press the or button one or more times

to highlight Time Set, then press the OK or

button to open the Time Set menu.

4 Press the or button one or more times

to highlight Time Set Mode, then press the

OK or button to select Manual.

5 Press the or button to select Year,

Date, or Time, then press the OK, , or

button to set the year, date, or time.

6 Press the EXIT button to close the on-screen

menu system.

Setting the sleep timer

The sleep timer lets you select the amount of

time before your TV turns off automatically.

To set the sleep timer:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Feature, then press the OK or

button to open the Feature menu.

3 Press the or button one or more times

to highlight Sleep Timer, then press OK or

button to select the amount of time. To turn

off the timer, select Off.

Viewing closed captions

You can view closed captions in two modes:

CAPTION and TEXT. Each mode has four

channels. CAPTION mode shows dialogue and

commentaries for TV programs while providing a

clear picture of the program. TEXT mode shows

information not related to the program, such as

TV program schedules and weather forecasts. In

TEXT mode, part of picture may be covered by

the text.

To view closed captions:

• Press the CCD button one or more times to

select a closed caption mode. You can select:

• CC1

• CC2

• CC3

• CC4

•TEXT1

•TEXT2

•TEXT3

•TEXT4

•Off

Setting parental controls

Your TV has a V-chip that lets you control the

type of programs your children can watch.

Parental controls include two ratings: MPAA

(based on age) and TV Parental Guidelines

(based on content and age). A TV program may

have an MPAA or TV Parental Guidelines rating,

so you should set controls for both ratings.

Before you can select ratings, you need to set up

a parental controls password.

To set up a password:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Feature, then press the OK or

button to open the Feature menu.

3 Press the or button one or more times

to highlight Parental Control, then press the

OK or button to open the Parental Control

menu.

Warning

To protect your TV, do not freeze the screen image for long

periods of time.

Note

You can also press the SLEEP button to set the sleep timer.

Note

For digital broadcast systems, you can press the CCD button

on the remote control to select the closed caption mode.

15

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

4 Press the or button one or more times

to highlight Password Change, the press the

OK or button to access the Password

Change option.

5 Press the number buttons to enter the old

password. If you have not set a password,

enter 0000.

6 Press the number buttons to enter a new

password, then enter the new password

again to confirm.

MPAA ratings

TV Parental Guidelines ratings

Some of the age based TV Parental Guidelines

ratings also have content based ratings.

To set the ratings:

1 Press the MENU button.

2 Press the or button one or more times

to highlight Feature, then press the OK or

button to open the Feature menu.

3 Press the or button one or more times

to highlight Parental Control, then press the

OK or button to open the Parental Control

menu.

4 Press the or button one or more times

to highlight Parental Control Set, then press

the OK or button to access the rating

feature.

5 Enter the password.

6 Press the or button to select a

rating, then press the OK button to block or

unblock the rating.

When you block a rating, that rating and all

higher ratings are blocked.

Using the on-screen menu system

Your TV has an on-screen menu system that lets

you adjust TV settings, such as video and audio

settings.

To use the on-screen menu system:

1 Press the MENU button.

2 Press the or button one or more times

to select a menu.

3 Press the or button to navigate to

an option or adjust an option.

4 Press the OK or button to confirm an

adjustment, open a sub-menu, or toggle a

setting.

5 Press the MENU button to return to a

previous menu or press the EXIT button to

close the on-screen menu system.

Caution

Write down your password and save it for future use.

Note

If you forget your password, enter 1397 for the old password,

then enter a new password.

Rating Description

NONE Not rated.

G General audiences.

PG Parental guidance suggested. Some

material may not be suitable for

children.

PG-13 Parental guidance strongly suggested.

Some material may not be suitable for

children under 13 years of age

R –Restricted. Not suitable for children

under 17 years of age unless

accompanied by a parent or guardian.

NC-17 Not suitable for children under 17

years of age.

X Adults only.

Rating Description

NONE Not rated.

TV-Y All children.

TV-Y7 Children over seven years of age.

TV-G General audiences.

TV-PG Parental guidance suggested.

TV-14 Parents strongly cautioned.

TV-MA Mature audiences only

Rating Description

FV Fantasy violence.

L Adult language.

S Sexual situations

V Violence.

D Sexually suggestive dialog.

16

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

On-screen menus

Programming the remote

control

Programming a device connected to your

TV

The remote control can control four devices,

such as a VCR, DVD player, cable or satellite

receiver, amplifier or tuner, or similar device.

To program the remote control:

1 Find the code for the device you want to

program. See “Appendix” on page 19. If there

is more than one code listed for a device,

write down all the codes.

2 Turn on the device you want to program, and

load media if required, for example a DVD.

3 Press a device key on the remote control, for

example, DVD, CBL, or AUX.

On-screen

menu

Options

Video

Note: Options may

vary in different

modes.

Picture Mode–Selects the picture mode: User,

Nature, Soft, or Bright. You can also press the

PICTURE button to select the picture mode.

Contrast–Increases the picture level to adjust

the white areas of the picture. Decreases the

picture level to adjust the black areas of the

picture.

Brightness–Increases the brightness to add

more light to dark areas of the picture.

Decreases the brightness to add more dark to

light areas of the picture.

Color–Adjusts the overall color of the picture.

Sharpness–Increases the sharpness level to

show cleaner and clearer images. Decreases

the level to show a smoother picture.

Aspect Ratio–Selects the screen aspect ratio:

Wide, Cinema, Normal, or Zoom. You can also

press the ZOOM button to select the aspect

ratio.

Advanced Video Menu–Provides access to

advanced features:

• Noise Reduction–Reduces picture

noise (snow).

• Tint–Increases the color level to add

more green to skin tones. Decreases the

color level to add more purple to skin

tones.

• Color Temperature–Selects one of

three automatic color adjustments: Cool

for more blue, Warm for more red, and

Normal.

• 3D Y/C–Turns the 3D comb filter on or

off.

VGA Set/Component Set–If your TV is

connected to a computer or to component

video, adjusts the following options:

• H-Pos–Adjusts the horizontal position

of the image.

• V-Pos–Adjusts the vertical position of

the image.

• Clock–Adjusts the sample frequency.

• Phase–Improves the focus of a stable

image.

• Setting–Resets VGA mode to the

factory defaults.

Audio

Note: Options may

vary in different

modes.

Sound Mode–Selects the sound mode: User,

News, Music, or Movie. You can also press the

AUDIO button to select the sound mode.

Bass–Adjusts the low sounds (bass).

Treble–Adjusts the high sounds (treble).

Balance–Adjusts the right and left speaker

volumes.

Earphone Vol–Adjust the earphone volume.

Digital Audio Output–Selects the audio mode

for the S/PDIF jack.

• RAW: AC-3 in and AC-3 out. PCM in

PCM out.

• PCM: AC-3 in PCM out. PCM in PCM

out.

MTS–Selects the multi-channel TV sound

(MTS): Mono, Stereo, or SAP (second audio

program). You can also press the MTS/SAP

button to select the MTS mode.

Audio Language–Selects an alternate language

if the program has more than one language.

Setup Tuning Band–Selects the TV signal source. For

more information, see “Selecting the TV

source” on page 12.

DTV Signal–Displays the digital TV signal

strength. For more information, see “Checking

the DTV signal strength” on page 13.

Auto Ch Search–Automatically sets up a list of

the channels available in your area. For more

information, see “Automatically setting up

channels” on page 13.

Manual Ch Set–Lets add or delete channels

from the channel list. For more information,

see “Manually adding or deleting channels

from the channel list” on page 13.

Channel Labels–Lets you add a label to a

channel. For more information, see “Adding a

channel label” on page 13.

Feature Source–Selects the video source. You can

select:

•TV

• Composite1

• Composite2

• Component1

• Component2

•VGA

•HDMI

•S-Video

You can also press the INPUT button to select

the video source.

Time Set–Sets the clock. For more

information, see “Setting the clock” on

page 14.

Sleep Timer–Sets the sleep timer. For more

information, see “Setting the sleep timer” on

page 14.

Parental Control–Access V-chip controls. For

more information, see “Setting parental

controls” on page 14.

Closed Caption Options–Customizes closed

captions for digital broadcasting systems. You

can adjust Size, Font, Text Color, Text Opacity,

Background Color, Background Opacity, Edge

Effect, and Edge Color.

CC when Mute–When this option is turned on,

your TV automatically displays closed captions

when the volume is muted.

Menu Language–Select the language for the

on-screen menu system. You can select

English, French, or Spanish.

On-screen

menu

Options

17

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

4 Press and hold the SET button on the remote

control until the LED blinks twice, then

release the button.

5 Enter the first five-digit code for your device.

The LED blinks once as each digit is entered.

If the code is correct, the LED blinks twice.

6 Aim the remote at the device, then press the

button.The device should turn off.

7 Repeat steps 1 through 6 to program

additional devices.

8 Press the SET button to save the code and

exit.

Searching for a code

To search for a code:

1 Press a device key.

2 Press and hold the SET button until the LED

blinks twice, the release the button.

3 Enter 991, then the device group number

(0=cable, 1=TV, 2=VCR, 3=audio). The LED

blinks twice.

4 Aim the remote control at the device, then

press the button. If the device responds,

go to step 7.

5 If the device does not respond, press the

CH+ button. Your remote control will try the

next code. Keep pressing the CH+ button

until the device responds. You can press the

CH– button to try a previous code.

6 To search for a code for another device,

repeat steps 1 through 5.

7 Press the SET button to save the code and

exit.

Checking the code

If you programmed a device by searching for a

code, you may want to know what four-digit code

the remote is using.

To check the code:

1 Press the device button on the remote

control.

2 Press and hold the SET button until the LED

blinks twice, then release the button.

3 Enter 990. The LED blinks twice.

4 Press 1 and count the LED blinks. This is the

first digit of the code. For example, if the LED

blinks twice, the first digit is 2. If the LED

does not blink, the first digit is 0.

5 Repeat step 4 using 2 for the second digit, 3

for the third digit, 4 for the fourth digit, and 5

for the fifth digit.

6 Press the SET button to exit.

Programming the volume lock

The remote control comes preset to let you

control the volume of each connected device.

You can change the volume lock so that one

device’s volume controls volume in all modes.

After you lock the volume control, you can unlock

the volume control for a specific device so you

can control the volume for that device

independently.

To lock the volume control:

1 Press and hold the SET button until the LED

blinks twice, then release the button.

2 Enter 993, then press the device button for

the device you want to control the volume.

The LED blinks twice. When you press the

VOL+, VOL–, or MUTE button on the remote

control, the device you selected controls the

volume regardless of which device you are

using.

To unlock the volume control:

1 Press and hold the SET button until the LED

blinks twice, then release the button.

2 Enter 993, then press VOL+ button. The LED

blinks four times. The volume control is

unlocked.

To unlock a single device’s volume control:

1 Press the device key.

2 Press and hold the SET button until the LED

blinks twice, then release the button.

3 Enter 993, then press VOL– button. The LED

blinks four times. The volume control for the

device you selected is unlocked.

Troubleshooting the remote control

Note

If the LED does not blink twice, repeat steps 3

through 5 using a different code.

Note

If the device does not turn off, repeat steps 4

through 6 using a different code. If you cannot find

a code that works, see “Searching for a code” on

page 17.

Symptom Possible solution

LED does not blink when

a button is pressed

Replace the batteries.

LED blinks when a

button is pressed, but

device does not respond

Make sure that you are at less than 15

feet (4.6 meters) from the device and

that you point the remote control at the

remote sensor on the device.

LED blinks one long

blink

You pressed an incorrect button. Start

the procedure over again.

Remote control does not

control a device or only

controls some features

of the device

Make sure that the device has a remote

sensor, then try another code.

No volume on a device See “Programming the volume lock”

on page 17.

18

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Maintaining

• Do not use your TV in areas that are too hot

or too cold because the cabinet may warp or

the screen may malfunction.

• Storage temperatures are 32

° to 122°F (0° to

50°C).

• Working temperatures are 41° to 104°F (5°

to 40°C).

• Do not place your TV in direct sunlight or

near a heat source.

Cleaning your TV

Clean the screen and cabinet with a soft,

lint-free cloth. If the screen or cabinet is

especially dirty, moisten a soft, lint-free cloth in a

weak detergent solution, squeeze the excess

moisture from the cloth, then wipe the screen or

cabinet with the cloth. Use a clean cloth to dry

the screen or cabinet.

Troubleshooting

Specifications

• Design and specifications are subject to

change without notice.

• Weight and dimensions listed are

approximate.

Caution

Avoid volatile substances, such as insect sprays, solvents, and

thinners.

Do not leave your TV in contact with items made from rubber

or PVC for long periods.

They may damage your TV.

Caution

Do not let liquids drip into the cabinet.

Warning

Do not try to repair your TV yourself. Refer all service to a

qualified service technician.

Symptom Possible solution

No power • Make sure that the power cord

is connected to your TV and an

electrical outlet.

• Unplug the power cord, wait 60

seconds, then plug the cord

back in and turn on your TV.

No picture • Make sure that the video cables

are connected securely to the

back of your TV.

• Adjust the contrast and

brightness.

• Make sure that the correct

video mode is selected.

• Make sure that the incoming

signal is compatible.

Good picture but no

sound

• Increase the volume.

• Make sure that the sound is not

muted.

• Make sure that the correct

audio mode is selected.

Good sound but poor

color

• Adjust the contrast, color, and

brightness settings.

Poor picture • Make sure that the room is not

too bright. Light reflecting off

the screen can make the picture

difficult to see.

• If an S-VHS camera or a

camcorder is connected while

another connected device is

turned on, the picture may be

poor. Turn off one or more

devices.

Horizontal dotted line • Your TV may be too close to

another electrical device, such

as a hair dryer or neon light.

Turn off the device or move

your TV.

Remote control does not

work

• Press the TV button.

• Replace the batteries. Make

sure that the + and – symbols

on the batteries align with the +

and – symbols in the battery

compartment.

• Clean the remote sensor on the

front of your TV.

• Bright or fluorescent lighting

may interfere with the remote

control signal. Turn off the light

or move your TV.

Snowy picture or noise • Make sure that the A/V cables

are connected correctly and

securely.

VGA picture is not stable

or synchronized

• Make sure that you have

selected the correct VGA mode

on your computer.

No ouput from one of

the speakers

• Adjust the balance in the Sound

menu.

Control buttons do not

work

• Unplug the power cord, wait

few seconds, then plug the cord

back in and turn on your TV.

Some parts of the

screen do not light up

• The plasma screen is

manufactured using a high level

of precision technology.

Sometimes parts of the screen

may be missing picture

elements or have luminous

spots. This is not a malfunction.

After images appear • Do not display a still image,

such as a logo, game, computer

image, for an extended period

of time. This can cause a

permanent after image to be

burned into the screen. This

type of damage is not covered

by your warranty.

TV makes snapping

sounds

• Snapping sounds occur when

your TV’s cabinet expands or

contracts from variation in

temperature. This is not a

malfunction.

Power supply AC 100-240 V 50/60 Hz

Power

consumption

140 W

Screen 27-inch

Channel coverage VHF: 2-13

UHF: 14-69

CATV: 1-125

CADTV: 1-135

DTV: 2-69

Weight 41.9 lbs. (19 kg)

Dimensions

W×H×D

28.25×24×9.25 inches

(71.4 × 60.6 × 23.5 cm)

Symptom Possible solution

19

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Appendix

VCR codes

Temperature Storage temperatures are 32° to 122°F

(0° to 50°C).

Working temperatures are 41° to

104°F (5° to 40°C).

TV system NTSC-M, ATSC

Accessories User guide

Remote control

ABS 21972

Admiral 20048, 20209

Aiko 20278

Aiwa 20037, 20479

Alienware 21972

America Action 20278

American High 20035

Amoisonic 20479

Anam 20162, 20037, 20240, 20278

Anam National 20162

Asha 20240

Audiovox 20037, 20278

Beaumark 20240

Bell & Howell 20104

Broksonic 20184, 20121, 20209, 20002,20479

Calix 20037

Canon 20035

Carver 20081

CCE 20072, 20278

Changhong 20048, 20081

Citizen 20037, 20278

Colt 20072

Craig 20037, 20047, 20240, 20072

Curtis Mathes 20060, 20035, 20162

Cybernex 20240

CyberPower 21972

Daewoo 20045, 20104, 20278

Dell 21972

Denon 20042

DirecTV 20739

Durabrand 20039, 20038

Electrohome 20037

Electrophonic 20037

Emerex 20032

Emerson 20035, 20037, 20184, 20240,20045,

20121, 20043, 20209, 20002, 20278,

20479

Fisher 20047, 20104

Fuji 20035, 20033

Fujitsu 20045

Gateway 21972

GE 20060, 20035, 20240

General 20045

Go Video 20432

GoldStar 20037, 20209, 20038, 20225

Haojie 20240

Harman/Kardon 20081, 20038

Harwood 20072

Hewlett Packard 21972

HI-Q 20047

Hitachi 20037, 20042, 20055

Howard

Computers

21972

HP 21972

Hughes Network

Systems

20042, 20739

iBUYPOWER 21972

JVC 20045, 20067

KEC 20037, 20278

Kenwood 20067, 20038

KLH 20072

Kodak 20035, 20037

Kolin 20043 LG 20037, 20045, 20042,

20209,20038

Logik 20072

LXI 20037

Magnavox 20035, 20039, 20081

Magnin 20240

Marantz 20035, 20081

Marta 20037

Matsushita 20035, 20162

Media Center PC 21972

MEI 20035

Memorex 20035, 20162, 20037, 20048,20039,

20047, 20240, 20104, 20209, 20479

MGA 20240, 20043

MGN Technology 20240

Microsoft 21972

Mind 21972

Minolta 20042

Mitsubishi 20067, 20043

Motorola 20035, 20048

MTC 20240

Multitech 20072

NEC 20035, 20037, 20048, 20104,20067,

20038

Newave 20037

Nikko 20037

Noblex 20240

Northgate 21972

Olympus 20035

Optimus 21062, 20162, 20037, 20048,20104,

20432

Orion 20184, 20209, 20002, 20479

Panasonic 21062, 20035, 20162, 20616,20225

Penney 20035, 20037, 20240, 20042,20038

Pentax 20042

20

Insignia NS-27LCD 27” LCD TV

www.insignia-products.com

Digital video disc codes

Philco 20035, 20479

Philips 20035, 20081, 20739, 20618

Pilot 20037

Pioneer 20042, 20067

Polk Audio 20081

Profitronic 20240

Proscan 20060

Protec 20072

Pulsar 20039

Qisheng 20060

Quasar 20035, 20162

Radix 20037

Randex 20037

RCA 20060, 20035, 20240, 20042,20880

Realistic 20035, 20037, 20048, 20047,20104

ReplayTV 20616

Runco 20039

Sampo 20037, 20048

Samsung 20240, 20045, 20432

Sanky 20048, 20039

Sansui 20067, 20209, 20479

Sanyo 20047, 20240, 20104

Scott 20184, 20045, 20121, 20043

Sears 20035, 20037, 20047, 20042,20104

Sharp 20048, 20209

Shintom 20072

Shogun 20240

Singer 20072

Sonic Blue 20616

Sony 20035, 20032, 20033, 20636,21972

STS 20042

Sylvania 20035, 20081, 20043

Systemax 21972

Tagar Systems 21972

Tashiko 20037

Tatung 20045, 20067

Technics 20035, 20162

Teco 20035, 20037, 20048, 20038

Teknika 20035, 20037

Tivo 20636, 20618, 21503, 20739

TMK 20240

Toshiba 20045, 20042, 20067, 20043,21503,

21008, 21972

Totevision 20037, 20240

Touch 21972

Unitech 20240

Vector 20045

Vector Research 20038

Victor 20067

Video Concepts 20045

Videomagic 20037

Videosonic 20240

Viewsonic 21972

Wards 20060, 20035, 20048, 20047,20081,

20240, 20042, 20072

White

Westinghouse

20209, 20072

XR-1000 20035, 20072

Yamaha 20038

Zenith 20039, 20033, 20209, 20479

ZT Group 21972

Aiwa 20641, 21912

Akai 20770

Allegro 20869

Apex Digital 20672, 20717, 20797, 21061,20796,

21056, 21937, 20794, 21020, 21915

Blaupunkt 20717

Blue Parade 20571

Broksonic 20695

Changhong 20627, 21061

CineVision 20869

Coby 21086

Curtis Mathes 21087

CyberHome 21024, 21023, 21129, 20816, 21117

Daewoo 20833, 21172, 20869

Denon 20490

DVD2000 20521

Emerson 20591, 20675

Enterprise 20591

Fisher 21919

Funai 20675

Gateway 21158, 21073

GE 20522, 20717

Go Video 20744, 20833, 21099, 20783,21075,

20869, 21730

Greenhill 20717

Harman/Kardon 20582, 20702

Hitachi 20573, 20664, 21919

Hiteker 20672

Initial 20717

Integra 20627, 21924

JBL 20702

JVC 20558, 20623, 20867

Kenwood 20490, 20534

KLH 20717, 21020, 21149

Koss 20651, 21980

Lasonic 20798

LG 20591, 20869, 20801

Liquid Video 21980

Lite-On 21158, 21058

Loewe 20511

Magnavox 20503, 20539, 21976, 21914, 20675

Marantz 20539

La page charge ...

Insignia Flat Panel Television NS-27LCD Manuel utilisateur

Ce manuel convient également à

Insignia Flat Panel Television NS-27LCD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents