Breville the Breville Sous Chef 12 Plus Manuel utilisateur

the Sous Chef

™

12 Plus

Instruction Book - BFP680

2

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

FOR ALL

ELECTRICAL

APPLIANCES

READ ALL

INSTRUCTIONS BEFORE

USE AND SAVE FOR

FUTURE REFERENCE

• Carefully read all

instructions before

operating the appliance for

the ﬁrst time and save for

future reference.

• Blades and cutting discs

are sharp. Handle them

carefully.

• Remove and safely discard

any packaging materials

and promotional labels

before using the appliance

for the ﬁrst time.

• To eliminate a choking

hazard for young children,

remove and safely discard

the protective cover ﬁtted

to the power plug of this

appliance.

• To protect against

electrical shock, do not

immerse the power cord,

power plug or motor base

in water or any other liquid.

• Do not place the appliance

near the edge of a counter

top or table during

operation. Ensure the

surface is level, clean and

free of water. Vibration

during operation may

cause the appliance to

move during use.

3

• Do not place the appliance

on or near a hot gas or

electric burner, or where

it could touch any other

source of heat.

• Do not use on a sink drain

board.

• Always make sure the food

processor is completely

assembled before

operating. The appliance

will not operate unless

properly assembled.

• Ensure the POWER | OFF

button has been pressed

and the power cord is

unplugged from the power

outlet before attaching any

blade, disc or lid.

• Handle the food processor

and attachments with care.

Blades and discs are razor-

sharp and should be kept

out of reach from children.

• To reduce the risk of

injury, always secure the

processing bowl onto

the motor base before

attaching the blades or

discs.

• Do not allow the power

cord to hang over the edge

of a table or counter, touch

hot surfaces or become

knotted. Unwind the power

cord fully before use.

• Keep hands as well as

spatulas and other utensils

away from moving blades

or discs while processing

food, to prevent the

possibility of severe

personal injury or damage

to the food processor.

A plastic spatula may be

used, but only when the

food processor is stopped.

Ensure the POWER | OFF

button has been pressed

to switch the motor off

and remove the power

cord from the outlet before

removing the lid from the

processing bowl.

• Avoid contact with moving

parts. Never push food

down by hand when slicing

or shredding. Always use

pusher.

4

• Make sure motor has

completely stopped before

removing cover.

• Be sure cover and feed

tube are securely locked

in place before operating

food processor.

• Never try to override

or tamper with cover

interlock mechanism.

• Always remove the plug

from the power outlet if

the appliance is not in

use, before attempting to

move the appliance, before

cleaning, disassembling,

assembling and when

storing the appliance.

• Some stiff mixtures, such

as dough, may cause the

processing blade to rotate

more slowly than normal.

If this happens, do not

process for longer than

1 minute.

• Do not process hot or

boiling liquids-allow

liquids to cool before

placing into the processing

bowl.

• Do not move appliance

while in operation.

• Do not place any part of

the food processor in a

microwave oven.

• Do not ﬁll the processing

bowl above the MAX

line. Always add drier or

thicker ingredients to the

processing bowl prior to

adding ﬂuids.

• Never remove the lid while

the appliance is operating.

Always use the POWER |

OFF or PAUSE buttons to

stop the machine before lid

removal.

• Care should be taken

when removing the food

from the processing

bowl by ensuring the

motor and blade/disc has

completely stopped before

disassembling. Ensure the

POWER | OFF button has

been pressed to switch the

motor off and unplug the

power cord from the power

outlet before removing the

lid from the processing

bowl. The processing bowl

5

should then be unlocked

from the motor body and

the blade/disc should be

carefully removed before

attempting to remove the

processed food.

• Do not use harsh abrasive,

caustic cleaners or oven

cleaners when cleaning the

appliance.

SAFEGUARDS

FOR YOUR FOOD

PROCESSOR

• This appliance is for

household use only.

Do not use the appliance

for anything other than

its intended purpose as

described in this book.

Do not use outdoors.

Do not use in moving

vehicles or boats.

• The use of attachments

not sold or recommended

by Breville may cause ﬁre,

electric shock or injury.

• Do not leave the appliance

unattended when in use.

• Ensure the motor

and blade/disc have

completely stopped before

disassembling. Ensure the

POWER | OFF button has

been pressed to switch the

motor off and unplug the

power cord from the power

outlet when not in use, if

left unattended and before

assembling, cleaning or

storing.

• This appliance is not

intended for use by young

children or inﬁrm persons

without supervision.

Young children should be

supervised to ensure that

they do not play with the

appliance.

• Regularly inspect the power

cord, power plug and actual

appliance for any damage.

Do not operate any

appliance with a damaged

cord or plug or after the

appliance malfunctions, or

is dropped or damaged in

any manner. Immediately

cease use of the appliance

and call Breville Consumer

Support.

6

• For any maintenance other

than cleaning, call Breville

Consumer Support.

• This appliance is equipped

with a power cord having

a grounding wire with

a grounding plug. The

appliance must be

grounded using a 3-hole

properly grounded outlet.

In the event of an electrical

short circuit, grounding

reduces the risk of

electrical shock.

• If the power outlet is

a standard 2-prong

wall outlet, it is your

personal responsibility

and obligation to have it

replaced with a properly

grounded 3-prong wall

outlet.

• Do not, under any

circumstances, cut or

remove the third (ground)

prong from the power cord

or use an adapter.

• Consult a qualiﬁed

electrician if the grounding

instructions are not

completely understood,

or if doubt exists as to

whether the appliance is

properly grounded.

BREVILLE ASSIST

®

PLUG

Your Breville appliance

comes with a unique

Assist

®

Plug, conveniently

designed with a ﬁnger hole

to ease removal from the

power outlet.

For safety reasons it is

recommended you plug

your Breville appliance

directly into its own

electrical outlet on a

dedicated circuit separate

from other appliances. If the

electric circuit is overloaded

with other appliances,

your appliance may not

function properly. Use in

conjunction with a power

strip or extension cord is

not recommended.

7

SHORT CORD

INSTRUCTIONS

Your Breville appliance

is ﬁtted with a short

power supply cord to

reduce personal injury or

property damage resulting

from pulling, tripping or

becoming entangled with a

longer cord.

If an extension cord is used,

(1) the marked electrical

rating of the cord set or

extension cord should

be at least as great as the

electrical rating of the

appliance, (2) the cord

should be arranged so

that it will not drape over

the countertop or table-

top where it can be pulled

on by children or tripped

over unintentionally and

(3) the extension cord

must include a 3-prong

grounding plug.

CALIFORNIA

PROPOSITION 65:

(Applicable to California

residents only).

This product contains

chemicals known to the

State of California to cause

cancer, birth defects or other

reproductive harm.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

8

O

R

P

N

Q

S

T

U

V

A

B

C

D

E

F

G

H

L

M

I

J

K

Components

9

A. Small food pusher

Use to process smaller ingredients with

greater control. It also doubles as a

measuring cup for ingredients. The food

processor will run continually when the small

pusher is out.

B. Mid food pusher

The food processor will run continually

whether the mid pusher is in or out.

C. Large food pusher

The food processor will not start unless the

large pusher is in place correctly, as it releases

the safety interlock system.

D. Extra wide feed chute

5 inch (13cm) wide, for large ingredients.

E. Safety interlock system

Prevents the motor from operating unless the

bowl and lid are correctly locked in position,

and large feed pusher is inserted.

F. Processing lid

Locks onto the processing bowl and forms

part of the safety interlock system.

G. Bowl coupling

Sintered stainless steel motor connector with

vibration absorption.

H. Processing bowl

12 cup capacity for dry ingredients and

8½ cups for thick liquid ingredients. Lock

onto base by turning clockwise.

I. PULSE button

Press and release for momentary bursts

of power.

J. START | PAUSE button

K. POWER | OFF button

Provides power to the food processor unit,

and puts it into READY mode.

L. Direct drive motor base

Induction motor for high torque and

reliable results.

M. No-skid rubber feet

N. Plastic spatula

Scrape the sides of the bowl to help process

ingredients evenly.

O. Silicone seal

This replaceable seal reduces the chance of

leakage while processing larger volumes of

liquid ingredients.

P. Dough blade

Blunt blade designed for a softer action of

combining dough ingredients.

Q. Micro-serrated S-Blade™

Swift action for even chopping, mixing,

whipping and processing a variety of

ingredients. Safety braking system

rapidly stops S-Blades if lid is

unexpectedly opened.

R. S-Blade™ cover

S. Adjustable slicer 0.3mm–8.0mm thickness

T. Fine and coarse reversible shredder

U. Spindle

V. Cord Storage

10

X

W

S-Blade

Dough Blade

Adjustable slicer

Fine and coarse

reversible shredder

Plastic spatula

Storage case

Spindle

W. Mini processing blade

Used for chopping, mixing, and blending a

variety of ingredients.

X. Mini processing bowl

For processing small volumes of ingredients.

Storage case

Store all discs and blades safely when not in use.

11

Assembly

BEFORE FIRST USE

• Before using your food processor for the ﬁrst

time, remove any packaging material and

promotional labels. Ensure the POWER button

is OFF and the food processor is unplugged.

• Be careful when handling the blades and discs

as they are extremely sharp.

• Wash the processing bowl, processing lid

and all attachments in warm soapy water with

a soft cloth. Rinse and dry thoroughly. The

attachments may be washed in the dishwasher.

• When ﬁrst using your food processor, you may

notice an odor coming from the motor. This is

normal and will dissipate with use.

• Always use the food processor on a dry, level

work surface.

ASSEMBLY

1. Position the processing bowl onto the motor

base with the handle in line with the ALIGN

HANDLE graphic on the motor base.

2. Turn the bowl clockwise until the handle

locks to the front. The processing bowl

should now be securely locked into position.

The food processor will not operate unless

the bowl is locked into position correctly.

3. The spindle is required when using ALL

discs and blades in the large processing bowl

(spindle not required for mini-bowl). Failing

to use the spindle will damage the parts, and

incorrect use this way may cause the parts to

fuse together.

4. Before placing the lid onto the processing

bowl, position the spindle over the coupling

in the center of the processing bowl. Then

position your chosen blade or disc over it.

The blades drop down lower than the discs.

12

5. Place lid onto the processing bowl so that

the ALIGN | LOCK graphics on the lid and

handle align. To LOCK the lid, hold the chute

and turn clockwise so that the handle parts

align. Locking the lid correctly will engage

the interlocking safety catch on the handle,

and allow the motor to run.

MINI PROCESSING BOWL

• The mini processing bowl ﬁts inside the

main bowl.

• The mini processing blades give you

maximum control for small quantities.

• Do not use the spindle, or the processing discs.

• The mini blades cannot be used in the main

processing bowl.

Functions

OPERATION

• The food processor will only operate when

the processing bowl, lid and large pusher are

correctly assembled. This engages the safety

interlock, and allows the motor to run.

• The POWER button illuminates red when the

machine is connected to power and is ready

to run.

• The START button allows the motor to run

continuously until pressed again. If the lid,

bowl or large pusher are removed while the

motor is running, the button will ﬂash. The

motor will resume running when the bowl, lid

and large pusher are assembled and the safety

interlock is engaged, the button light will be

solid (no longer ﬂashing).

• The momentary PULSE button is ideal for

processing foods that need sudden bursts of

power. It also encourages ingredients to move

around the bowl. PULSE is also best when

processing foods that only require processing

for a short period of time.

• Use a combination of the START and PULSE

buttons for control when processing food.

• The chute has a MAX CHUTE FILL graphic to

indicate the maximum volume of food that can

be placed in the chute for the pusher to activate

the safety locking catch.

• After processing, wait until the blades/discs

have stopped moving before unlocking the

lid. To ensure safe handling, turn off at the

POWER button and unplug at the power

outlet before handling the blades.

• When removing blades/discs, lift carefully by

gripping the plastic hub in the center.

13

OVERLOAD PROTECTION SYSTEM

• The food processor has an overload protection

system to prevent damage to the motor.

If activated, the food processor will go into

STANDBY mode, and the buttons will ﬂash.

• Unplug and allow to cool for 30 minutes.

Once cooled, you will be able to use the food

processor as usual again.

• Note that some stiff mixtures (such as bread

dough) may cause the blade to rotate more

slowly than normal. If this happens, do not

process for more than 1 minute.

• If the blades or discs jam with food while

processing, immediately and unplug from

the power outlet before clearing the wedged

food. If this happens more than once, the

bowl may be overloaded. Try processing in

smaller batches.

CHOPPING WITH THE

MICRO-SERRATED S-BLADE™

The S-blade chops raw and cooked food

to the consistency required, from coarsely

chopped to minced. The blades process very

efﬁciently, and may take

less time than expected to process many

large tasks.

Always remember to place the spindle and

S-blade into the processing bowl before

adding the food.

Avoid over-processing by checking the

consistency frequently. For many tasks, we

recommend using the PULSE button, as it

may only take a few seconds to fully process

food to your desired consistency.

If necessary, turn the POWER off and use a

spatula to scrape down the sides of the bowl

to encourage even processing.

Raw vegetables, fruit and cooked meats

Trim and cut food into 1 inch (2.5cm) cubes.

Process no more than 6 cups at a time using

the PULSE button at 1–2 second intervals

until chopped to desired size or consistency.

Raw meat, chicken and ﬁsh

Trim excess fat and cut food into 1 inch

(2.5cm) cubes. Ensure all bones are removed.

Chill well in freezer until ﬁrm as this will help

to cut through the food more readily. Process

no more than 2¼ pounds (or 1kg) of raw meat

at a time. At this capacity the motor should

run for no more than 30 seconds at a time.

Use a combination of the START and the

PULSE button until chopped or minced to the

desired consistency.

Garlic, chilli and ginger

Peel garlic cloves and process them whole.

Leave chillies whole, or remove seeds for

milder chilli. Peel and cut ginger into 1 inch

(2.5cm) cubes.

For other solid herbs like lemongrass or

galangal, peel and cut into cubes or pieces

between ½ and 1 inch in size.

Size should be made smaller for harder or

more dense herbs.

Process using the PULSE button at

1–2 second intervals until chopped to the

desired consistency.

Store chopped herbs with a little vegetable oil

in an airtight container in the refrigerator for

up to 1 week.

If adding garlic, chilli or ginger to other

ingredients, drop whole pieces down the

small feed chute while the motor is running.

Leafy herbs

Wash and dry herbs thoroughly. Remove

any coarse stems. Process no more than

2 bunches of herbs (approx. 4 cups) at a

time using the PULSE button at 1–2 second

intervals until chopped to the desired

consistency.

Use leafy herbs immediately for the most

aromatic results in your recipe.

14

Nuts

Process no more than 4½ cups of shelled

nuts at a time using the PULSE button at

1–2 second intervals until chopped to the

desired consistency.

Dried fruit

Dried fruit can be sticky, and may stick to the

blades during processing. We recommend

putting dried fruit in the freezer for about

10 minutes before processing. Process no

more than 2 cups at a time using the PULSE

button at 1–2 second intervals until chopped

to the desired consistency.

If chopping fruit to add to cake mixture,

process the fruit before making the cake mix.

Add a little ﬂour (from the quantity of ﬂour

in the recipe) to prevent fruit from sticking to

the S-blade.

We do not recommend to process large dried

fruits such as dates and ﬁgs.

Soft breadcrumbs

Break stale bread into chunks (fresh bread

will stick to blades). Process no more than

4–6 slices at a time using the PULSE button

at 1–2 second intervals until crumbed to

desired consistency. For best results when

making bread crumbs, add one slice at a time.

Dried breadcrumbs

Tear bread into chunks and toast in oven until

golden and crisp. Do not over brown. Process

no more than 4–6 slices at a time using the

PULSE button at 1–2 second intervals

Cookie crumbs

Break cookies into quarters, and weigh a

maximum of 8oz (250g). Process using the

PULSE button at 1–2 second intervals until

chopped to the desired consistency. Sweet

or savoury cookie crumbs can be used as an

alternative to pastry for sweet or savory pies.

Do not process very hard cookies as this may

damage the blades.

PURÉEING WITH THE

MICRO-SERRATED S-BLADE™

The S-blade purées raw and cooked food to

the consistency required, including baby food.

The blades process very efﬁciently, and cut

the time needed to purée many tasks.

Always remember to place the S-blade into

the processing bowl before adding the food.

Carefully remove the S-blade after puréeing

food and use a spatula to scrape food

adhering to the blade and bowl.

Baby food

Trim and cut vegetables and meat into 1 inch

(2.5cm) cubes. Cook vegetables and meat

before processing. Process no more than

6 cups at a time using the START button in

intervals until the food is puréed to a smooth

and even consistency. Stock, milk or gravy

can be added through the small feed chute if

the mixture becomes too thick.

Excess baby food can be frozen in

ice-cube trays, and packed in single serve

freezer bags ready for use.

Peanut butter

Process no more than 4½ cups of shelled

nuts at a time using the START button until

chopped to the desired consistency.

The volume of nuts reduces after processing,

for example 2 cups of nuts will make around

1 cup of nut butter.

Natural nut butter (without using stabilizers)

will separate on standing, and needs to be

stirred before use.

15

MIXING WITH THE

MICRO-SERRATED S-BLADE™

The S-blade mixes ingredients for cakes,

batters, and cookie doughs.

The S-blade can also emulsify egg-based

sauces such as mayonnaise.

Always remember to place the spindle and

S-blade into the processing bowl before

adding the food.

Butter cake and cookie dough

Place softened, chopped butter and sugar

into the processing bowl. Process using the

START button until the mixture is lightly

creamed. With the motor running, add eggs

one at a time through the small feed chute,

mixing well after each egg is added. Take lid

off and add liquid and dry ingredients to the

mixture. Process using the PULSE button

until folded evenly. Scrape down sides of bowl

as needed. Do not over-process.

Add choc chips, nuts, dried fruit, etc after

the main mixture is done. Use the PULSE

button in very short bursts until the additions

are combined. Do not over-process, as these

larger ingredients will break down quickly.

Quick-mix cakes and batters

Place all ingredients in the bowl, starting with

liquids, and being careful not to exceed the

MAX LIQUID level. Process using the PULSE

button until folded evenly. Scrape down sides

of bowl as needed. Do not over-process.

This method can also be used for

melt ’n’ mix cakes, packet cake mixes

and crêpe batters.

Pastry dough

Place ﬂour and chilled, cubed butter into the

processing bowl.

Do not process more than 2 cups (300g) of

ﬂour using the START button in intervals

until the butter is absorbed into the ﬂour.

Steadily add liquid through the small feed

chute with the motor still running. Process

until the mixture forms a ball.

KNEADING WITH THE

DOUGH BLADE

Always remember to place the spindle and

dough blade into the processing bowl before

adding the food.

The edges of the plastic dough blade

create a softer action for combining dough

ingredients. The dough blade encourages the

gluten strands to be stretched rather than cut,

and should be used for all yeast doughs, and

any other doughs that require kneading.

Bread or pizza dough

Place ﬂour and dry ingredients into the

processing bowl, including instant active

dry yeast.

Do not process more than 5 cups (700g) of

ﬂour or using the START button in intervals.

Steadily add liquid (including oil, if

applicable) through the small feed chute with

the motor still running. Process until

the mixture until it forms a soft, elastic

dough ball.

Transfer dough ball to a lightly ﬂoured

surface and knead for a further 5 minutes if

necessary until soft and pliable.

If processing more than two recipes of dough

ingredients (700g ﬂour), allow the motor

base to cool for an extended period before

subsequent kneading to prevent the motor

from overloading.

Place dough into a large, greased mixing

bowl and cover. Stand in a warm place until it

has doubled in size. Turn the dough out onto

a lightly ﬂoured surface and knead again until

smooth and elastic. Shape the dough then

allow to rise in a warm area before baking in

a hot oven.

16

SLICING, GRATING AND SHREDDING

Important: the spindle must be used

with both the adjustable slicer and

the reversible shredder/grater.

Adjustable slicer

The adjustable slicer will slice food to an even

and consistent thickness. It can be adjusted

to 24 settings, from very ﬁne (0.3mm) to thick

(8.0mm). To adjust the slicing thickness, hold

the adjustable slicing disc by the outer edge

with one hand, and turn the adjustment

dial on the underside with the other hand.

An arrow graphic indicates the thickness of

the slice you will get.

Reversible grater and shredder

This disc has an array of small blades on

both sides of the disc. Align the disc so larger

holes face up for courser textured results,

or with the smaller holes facing up for ﬁner

results. The discs are labelled showing which

side faces up.

CONTROLLING THE INGREDIENTS

It is important to position the food in

the chute to gain maximum control and

best results.

Smaller ingredients

For long thin foods such as carrots,

cucumbers, zucchini, etc., use the small feed

chute. This will avoid the ingredient from

tipping over during slicing.

Larger ingredients

The wide feed chute is 5 inch (13cm) wide,

and can ﬁt ingredients up to this size. The

chute can be packed to ﬁll the width of the

chute. The food should ﬁt snugly so it is

supported in an upright position in the chute,

but not so tight that it could prevent the food

from moving down the chute.

Medium feed chute

Use the medium feed chute for ‘in-between’

food processing. The medium feed chute is

2¾ inch (7cm) wide, and can ﬁt ingredients

up to this size. The chute can be packed to

ﬁll the width of the chute. The food should

ﬁt snugly so it is supported in an upright

position in the chute, but not so tight that it

could prevent the food from moving down

the chute.

Take care not to overﬁll the chute, as the

pusher will not activate the interlock safety

catch if the chute is too full. Do not ﬁll over

the MAX CHUTE FILL graphic.

Ensure the large pusher is in place before

using the medium pusher.

Pressure

When processing, never force the food down

the chute as this can damage the discs.

Apply light pressure for soft foods such as

tomatoes and bananas.

Apply medium pressure for ﬁrmer foods such

as potatoes and apples.

Apply ﬁrm pressure for hard foods such

as parmesan cheese and deli meats such

as salami.

Round fruit and vegetables

Prepare fruit or vegetables by washing and

peeling (if necessary).

Small fruit and vegetables should be trimmed

on one end so the food sits ﬂat inside the

feed chute.

Large fruit and vegetables may need to be cut

in half to ﬁt in the chute. Pack the chute from

left to right.

17

Long fruit and vegetables

Prepare fruit or vegetables by washing and

peeling (if necessary).

Ingredients can be cut cross-sectionally to

create circular results. Use the small and

medium feed chute, or pack ingredients

vertically in the large feed chute.

Ingredients can be cut lengthwise to create

ribbons. Use the large feed chute, and trim

ingredients if necessary to encourage them to

sit ﬂat in the feed chute when the disc starts.

Pack the large feed chute horizontally.

Leafy vegetables

Cut cabbage into wedges to ﬁt the feed chute.

For lettuce, separate leaves, then roll up and

pack vertically in the feed chute.

Cheese

Caution should be taken when processing

cheese in a food processor. For soft cheese

such as mozzarella, partially freeze it until

ﬁrm. This will help prevent jamming the disc.

Round cheeses such as mozzarella should be

trimmed at one end to encourage them to sit

ﬂat in the feed chute with the disc starts.

Hard cheeses such as parmesan must be

checked ﬁrst to ensure they are not too hard

(to avoid damaging blade edges). The cheese

should slice easily with a sharp knife and

remove the rind before processing.

Wedged shaped cheeses such as parmesan

can be packed side by side to form a

rectangular shape in the chute.

Deli meats

Cut in lengths to ﬁt the height of the feed

chute. The length must not be higher than

MAX CHUTE FILL graphic. Pack with the

cut side facing down. For hard cured sausages

like salami and pepperoni trim on one end

and process one sausage at a time through

the small or medium feed chute, depending

on size.

Grated Chocolate

Break a block of chocolate into small pieces,

and chill until ﬁrm. Pack into the small feed

chute, and then grate using either the coarse

or ﬁne side of the reversible shredder (do not

use S-blade or adjustable slicer).

MINI BOWL AND BLADE

The mini processing bowl is used inside the

main processing bowl. It is for better control

when processing small quantities of food, or

herb/spice mixes. It can be used for chopping,

mixing and blending a variety of ingredients.

The mini blade can not be used inside the

main processing bowl.

The main processing attachments will not ﬁt

inside the mini bowl.

18

Food Processing Guide

For more information about preparation of food and how to process, refer to basic

processing techniques. For speciﬁc recipes, refer to the recipe section.

FOOD BLADE TYPE ADJUSTABLE SLICING

DISC THICKNESS

RECOMMENDED

DISC TYPE

Avocado

S-blade or mini

Use: Guacamole

2–5

Beets (cooked) 2–5

Shredder

Use: Salad

Butternut Squash

S-blade

Use Butternut Squash

soup

Cabbage / Lettuce

Thin 1–2 and med 2–3

Use: Accompaniment

Shredder

Use: Salad

Carrot

S-blade or mini

Use: Vegetable soup

0–5

Shredder

Use: Salad

Cauliﬂower (cooked)

S-blade or mini

Use: Cauliﬂower soup

Celery

S-blade or mini

Use: Vegetable soup

Thin 1–2 med 2–3

Use: Salad

Eggplant

S-blade or mini

Use: Accompaniment,

soups

2–5

Use: Grilled eggplant

Herbs

S-blade or mini

Use: Seasoning or pesto

Leeks

S-blade

Use: Cooked for soups

2–5

Use: Vegetable soup

Onion

S-blade or mini

Use: Soups, sauces

0–5

Use: Salad

Potatoes

0.3–6

Use: Potato au Gratin

Shredder

Use: hash browns

Potatoes (cooked)

S-blade or mini

Use: Mash potato

Tomatoes

S-blade or mini

Use: Salsa

2–5

Use: sandwich ﬁlling,

caprese salad, tomato

relish

19

FOOD BLADE TYPE ADJUSTABLE SLICING

DISC THICKNESS

RECOMMENDED

DISC TYPE

Apple / Pear

S-blade or mini

Use: Apple sauce

2–5

Use: Apple pie

Apple / Pear

(cooked)

S-blade or mini

Use: Baby food

4–6

Use: Fruit salad

Dried Fruit

S-blade

Use: Fruit salad, dessert

sauce

Batters

S-blade

Use: Cakes, pancake,

wafﬂe batter

Breadcrumbs

S-blade or mini

Use: Coatings,

breadcrumb stufﬁng

Cheese

2–5

Use: Garnish,

sandwich ﬁllings

Shredder - coarse

or ﬁne

Use: Grated cheese

for pizza

Chocolate

S-blade or mini

Use: Chocolate

ganache

Shredder -

Coarse or ﬁne

Use: Dessert

decoration

Doughs (pastry)

S-blade

Use: Tarts, Pies

Doughs

(bread, pizza)

Dough blade

Use: Bread, pizza

Eggs (whole or

yolks)

S-blade or mini

Use: Mayonnaise

Meat (raw)

S-blade

Use: Meatloaf, burgers,

meatballs

Meat (cooked)

S-blade

Use: Sandwich ﬁllings,

pate, baby food

Meat (deli)

1–6

Use: Sandwiches,

antipasto, pizza toppings

20

Care & Cleaning

Stubborn food stains and odors

Strong smelling foods such as garlic, ﬁsh and

some vegetables such as carrots may leave an

odor or stain the bowl or lid.

To remove, pour warm soapy water and ﬁll to

the MAX LIQUID mark. Set aside to soak for

5 minutes, without immersing the whole bowl.

Then wash with a mild detergent and warm

water, rise well and dry thoroughly. Store the

bowl with the lid off.

Storage

Place the large food pusher (with medium

and small pushers inserted) into the feed

chute for storage.

Store your food processor upright, with the

bowl and lid resting in position, but not

locked. Locking the bowl and lid can put

unnecessary strain on the safety interlock.

All accessories should be kept in the storage

container and out of the reach of children to

avoid accidental cuts. It is not recommended

to store the discs in a drawer with other

utensils.

Do not place anything else on top of your

food processor during storage.

Remove the power cord from the power outlet

after use for safety reasons.

Processing bowl and lid

Due to the interlock components, we do not

recommend immersing the bowl in water for

long periods.

To keep your bowl and lid clean, and to avoid

food drying on, follow these steps as soon as

possible after use:

• Rinse most of the ingredients off the bowl

and lid.

• Hand wash in warm, soapy water using a mild

liquid detergent and non-abrasive sponge.

Motor base

To clean the motor base, wipe with a soft,

damp cloth then dry thoroughly. Wipe any

excess food particles from the power cord.

Cleaning agents

Do not use abrasive scouring pads or

cleansers on either the motor base or the jug,

as they may scratch the surface. Use only

warm soap water with a soft cloth.

Dishwasher

The processing bowl and lid may occasionally

be washed in the dishwasher (top shelf

only), however washing in the dishwasher

is not recommended on a regular basis, as

prolonged exposure to harsh detergents,

hot water and pressure will damage and

shorten the life of the plastic and the

interlock components.

La page charge ...

Breville the Breville Sous Chef 12 Plus Manuel utilisateur

Ce manuel convient également à

Breville the Breville Sous Chef 12 Plus Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents