Kreg Pocket-Hole Jig 720 Manuel utilisateur

English 2

French 23

Spanish 45

OWNER’S MANUAL

We’re here to help.

We want you to have an exceptional project building experience.

If you have questions or need support, please get in touch.

1-800-447-8638 | [email protected]

Tell us about your experience.

Your opinion counts. And we’re always looking for ways to improve.

Share your feedback so we can keep growing and innovating for you.

www.kregtool.com/feedback

WARNING Every user must read and follow instructions and safety precautions in this manual.

Failure to do so could result in serious injury. Save manual for future reference.

Kreg Pocket-Hole Jig 700-Series

Manual applies to all 700-Series Pocket-Hole Jigs

2

Safety Precautions

WARNING Before using a power tool with this product, read and follow the

tool manufacturer’s instructions and safety precautions in addition to the safety

precautions below to reduce the risk of serious injury from hazards such as re,

electric shock, or rotating drill bit.

■ Always wear personal protective equipment recommended by the manufacturer of

the power tool you are using, such as eye, hearing, or respiratory protection.

■ The drill bit is sharp. Handle with care.

■ Do not allow familiarity gained from frequent use of your tools to replace safe

work practices. A moment of carelessness is sufcient to cause serious injury.

■ Avoid awkward hand positions where a sudden slip could cause contact with the

rotating bit.

■ When drilling, always ensure that the workpiece is clamped securely. It is

dangerous to hold the workpiece in place by hand.

WARNING Do not operate this tool or any machinery while under the inuence of

drugs, alcohol, or medications.

WARNING This product can expose you to chemicals including Acrylonitrile and

other chemicals, which are known to the State of California to cause cancer and

reproductive harm. For more information go to www.P65Warnings.ca.gov.

Table of Contents

Safety Precautions . . . . . . . . . .2

Pre-Assembly . . . . . . . . . . . . .3

Product Description. . . . . . . . . 3

Onboard Tool Storage. . . . . . . . 4

Adjustable Clamp Pressure . . . . .4

Extension Wings . . . . . . . . . . 5

Mounting Option . . . . . . . . . . 5

Dust Collection Accessories . . . . 6

Docking Station Assembly . . . . . .7

Operation - Drilling Pocket Holes . 12

Operation - Drilling and Driving

Pocket-HoleScrews . . . . . . . . 17

Using Your Kreg Jig. . . . . . . . . 18

Removing the Jig from the Docking

Station. . . . . . . . . . . . . . . . 19

Removing a Kreg 700-Series Jig

fromaMountedDocking Station . 19

Removing a Kreg 700-Series Jig from

an Unmounted Docking Station. . 20

Maintenance . . . . . . . . . . . . 21

Care and Cleaning . . . . . . . . . 21

Accessories . . . . . . . . . . . . . 21

3

Pre-Assembly

Review this section before you begin. Ensure that you have all tools and materials on

hand. Compare the package with the items listed in the Product Description section.

If any item is missing or lost, do not use this product. Contact Technical Support or

return the product to the place of purchase.

Product Description

A

B

K

L

M

N

C

D

E

F

G

O

J

I

H

Part Description Part Description

A KPHJ720 Jig H

1

Dock adapters for KPHJ720 (2)

B Dust collection blade I

1

Material support wings (2)

C Dust adapter J

1

Adjustable stop arm

D Material thickness gauge/Hex wrench K

1

Adjustable stop knob

E Easy-set pocket-hole drill bit L

1

Adjustable stop base

F Easy-set stop collar M

1

Adjustable stop base wedge

G Driver bits (3" and 6") N

1

Adjustable stop square nut

O

1

KPHA760 Pocket-hole jig clamp

1

These parts from the KPHA750 pocket-hole jig docking station are included with the

KPHJ720PRO package.

Note The product also includes two sample screw packs (not shown).

4

Onboard Tool Storage

The KPHJ720 Jig (A) provides onboard

tool storage for these items:

■ Easy-set pocket-hole drill bit (E) with

easy-set stop collar (F) attached

■ Material thickness gauge/hex

wrench(D)

■ 3" and 6" driver bits (G)

E

F

D

G

A

Adjustable Clamp Pressure

A knob (1) on the side of the KPHJ720 Jig enables you to increase or decrease the

clamp pressure that is applied to your workpiece. Five pressure settings are available.

The jig ships from the factory with the clamp pressure at the middle setting.

To adjust the clamp pressure:

a. Lift the jig handle all the way up to

release the clamp pressure.

b. Rotate the clamp-pressure

adjustment knob (1) one click in the

desired direction:

■ Clockwise to decrease pressure

■ Counterclockwise to increase

pressure

2

1

c. With a test block in place, reapply the clamp pressure by pressing the jig handle

down in one smooth motion until the jig handle is at its travel limit.

d. Repeat this process as needed until you are satised with the clamp pressure.

Note

■ The jig is set to minimum clamp pressure when the “minus” sign on the clamp-

pressure adjustment knob (1) aligns with the selection mark (2).

■ The jig is set to maximum clamp pressure when the “plus” sign on the clamp

pressure adjustment knob (1) aligns with the selection mark (2).

5

Extension Wings

The KPHJ720 Jig has two extension

wings, one (1) on each side of the jig

base. You can rotate one or both wings

out to 90 degrees to provide added

stability and material support.

Note If you use the optional docking

station with the jig, you will use the

docking station’s material support wings

instead of the extension wings shown

here. See Docking Station Assembly

onpage7.

1

Mounting Option

If desired, you can mount the KPHJ720 Jig to your work surface for added stability.

Note These instructions apply to a jig that is used without the optional docking

station.

a. Place the jig in the desired position on your workbench.

b. Rotate the extension wing (1) on each side of the jig to 90 degrees.

Two mounting holes (2) are now accessible (one hole on each side of the jig).

c. Drive one Kreg pocket-hole screw (3) through each mounting hole(2).

Note You can use Kreg SML-C125 screws or any other Kreg pocket-hole screw.

22

3

1

6

Dust Collection Accessories

You can use the provided dust collection accessories to capture dust as you drill.

To attach the dust collection accessories:

a. If necessary for the hose diameter you are using, attach the dust adapter (C) to

the wide end of the dust collection blade (B).

Hose diameter Requires dust adapter?

1-1/4" No

1-7/8" No

2-1/2" Yes

b. Insert the narrow end of the dust collection blade (B) into the left or right side of

the jig.

B

C

Note You can leave the dust collection blade and dust adapter attached to the jig

when the jig is not in use.

7

Docking Station Assembly

This section describes how to assemble the docking station that is included with the

KPHJ720PRO package. You can also purchase the docking station separately (see

Accessories onpage21).

Note If you are not using the docking station, skip this section and continue to

Operation - Drilling Pocket Holes onpage12.

1

Connect the Dock Adapters to the Jig

a. Place the KPHJ720 Jig (A) on a at surface.

b. With one hand, lift one side of the jig (A) slightly.

c. With your other hand, place a dock adapter (H) under the jig (A) so that the

attachment pins (1) t into the corresponding hole on the underside of the

jig(A); then slide the dock adapter (H) toward the jig handle (3) to lock the dock

adapter(H) into position.

Note One side of a dock adapter (H) has attachment pins (1) that t under the

jig; the other side has a connector (2) for a material support wing (not shown).

Ensure that the wing-connector side (2) of the dock adapter (H) extends out

from the side of the jig (A).

d. Repeat steps b and c to connect the other dock adapter (H) on the opposite side

of the jig (A).

H

A

1

2

3

8

2

Connect the Material Support Wings to the Dock Adapters

Tip The material support wings also

serve as storage boxes.

a. Hold a material support wing (I)

right-side up (so that the lid of

the storage box is facing up and

opens away from you).

b. Align the connector (1) on the side

of the material support wing (I)

with the connector (2) on the dock

adapter (H) that extends from the

side of the jig (A); then press the

material support wing (I) down

rmly so that the connectors snap together.

Note The bars on the material-support-wing connector (1) snap into the

grooves on the dock-adapter connector (2).

c. Repeat these steps to connect the other material support wing (I) to the dock

adapter (H) on the opposite side of the jig (A).

Note You can fold the material support wings up to the vertical position to save

space when the jig is not in use, or to make it easier to move the jig from one location

to another. Always fold the material support wings down before using the jig.

Note If you use the dust collection accessories (page6), you must remove them

from the jig in order to fold the material support wings up.

To fold up the material

supportwings:

■ Fold the material support wing (I) up

to a vertical position.

■ Rotate the wing lock (1) inward until

the latch (2) engages securely in the

notch (3) on that side of the jig.

To fold down the material

supportwings:

■ Rotate the wing lock (1) outward until

the latch (2) disengages from the

notch (3) in the side of the jig.

■ Fold the material support wing (I)

down to the horizontal position.

1

2

3

I

1

2

3

I

1

2

H

A

9

3

Optional: Mount the Dock Adapters to a Work Surface

If desired, you can mount the dock adapters to your work surface for added stability.

a. Place the docking station (with the 700-Series Jig attached to it) in the desired

position on your workbench.

b. Drive one Kreg pocket-hole screw (1) through each of the four mounting holes (2)

in the dock adapters (H).

Note You can use Kreg SML-C125 screws or any other Kreg pocket-hole screw.

H

1

2

10

4

Assemble the Adjustable Stop Base

The docking station includes an adjustable stop that can be attached to either

material support wing. The adjustable stop makes it easy to achieve repeatable

results when you have many pieces that require the same pocket-hole spacing.

Note The adjustable stop has two parts: the adjustable stop base, which you will

assemble in this step; and the adjustable stop arm, which can be attached to the

adjustable stop base in different congurations (see step5).

a. Insert the screw (1) of the adjustable

stop knob (K) into the hole on top of

the stop base (L).

b. Holding the knob (K) in position, turn

the stop base (L) upside down so

that the screw (1) extends upward.

c. Drop the adjustable stop base

wedge (M) onto the screw (1) with its

anged side facing up.

Note The adjustable stop base

wedge (M) should sit ush with the

adjustable stop base (L). If it does

not sit ush, rotate the adjustable

stop base wedge (M) 90degrees.

d. Place the adjustable stop square

nut(N) onto the screw (1); then rotate

the adjustable stop knob (K) until

the adjustable stop square nut (N)

isnger-tight.

K

L

1

M

1

N

11

5

Attach the Adjustable Stop Arm to the Adjustable Stop Base

Slide a notch in the adjustable stop arm (J) down over the tab (1) on the adjustable

stop base (L) until the adjustable stop arm (J) is fully seated on the tab(1).

Note The adjustable stop arm (J) has three notches: a center notch (2) on one

side and two outer notches (3, 4) on the opposite side. Use the appropriate notch

depending on how you want to congure the adjustable stop.

Note To change the conguration of the adjustable stop, lift the adjustable stop arm

(J) off the adjustable stop base (L). Then slide a different notch of the adjustable stop

arm (J) over the tab (1) on the adjustable stop base (L).

1

J

L

2

3

4

Centered Conguration Side Conguration

Use the arm’s center notch(2)

J

L

J

L

Use either of the arm’s outer notches (3,4),

so that the arm (J) extends to one side of the

base (L)

J

L

J

L

12

Operation - Drilling Pocket Holes

1

Determine the Material Thickness and Set the Stop Collar

a. Use the material thickness gauge (D) to determine the material thickness range.

b. Set the stop collar (F) by placing it on the drill bit (E) and aligning the window of

the stop collar (F) with the measurement thickness range determined in stepa.

c. Use the hex wrench built into the material thickness gauge (D) to lock the stop

collar (F) into place on the drill bit (E).

Note If your material thickness falls in the range, use the same setup

techniques as the 3/4" range with a 1-1/2" screw.

D

E

F

D

2

If applicable: Stabilize the Jig

■ If you are using the docking station: Fold both material support wings

down to their horizontal position (1).

■ If you are not using the docking station: You can rotate one or both of the

jig’s extension wings (2) out from the jig base to provide additional stability, if

desired.

1

With docking station: Material

support wings folded down

2

Without docking station: Extension

wings rotated out

13

3

Position Your Workpiece

a. Place your workpiece in the jig and use the drill guide to align it.

Note There are two alternate methods for aligning your Kreg Jig with your

workpiece:

■ Align the center line of any pocket-hole guide (numbers 1, 2, or 3) with

the desired location on your workpiece. For wider panels (over 3-1/2"

wide) pocket holes should be placed 5/8" to 1-1/2" from each edge of the

workpiece and then every 6" to 8".

■ Use the board centering marks (letters A, B, or C) to center two pocket holes

on the workpiece ranging in width from 1-1/4" to 3-1/2" wide. See the table

below for details on each size range.

1 2 3 A B C

Board Width Center Mark Drill Guide

1-1/4" to 1-3/4" C 2 and 3

1-3/4" to 2-3/8" A 1 and 2

2-3/8" to 3-1/2" B 1 and 3

b. When you are satised with the position of the workpiece in the jig, continue to

step4.

14

4

Clamp Your Workpiece

a. Press down on the jig handle (1)

in one smooth motion until the jig

handle (1) is at its travel limit.

Note If you have difculty pressing

the jig handle (1) to its travel limit,

decrease* the clamp pressure.

b. Check to see if your workpiece is

held securely in the jig; increase* the

clamp pressure, if necessary.

Note Increase the clamp pressure

if the clamp does not hold the

workpiece as securely as you

want, if you see movement in the

workpiece, or if you are using a plug

cutter drill guide attachment.

* See Adjustable Clamp Pressure

onpage4.

1

5

Optional: Set the Adjustable Stop

Note The adjustable stop enables you to drill pocket holes on similar workpieces at

a faster pace. The adjustable stop is an accessory that is included with the docking

station. Ifyou are not using the docking station, skip this step and continue to step6.

a. If necessary, change the conguration of the adjustable stop to accommodate

the size and orientation of your workpiece in the jig:

■ Wide workpiece: If the workpiece is wide enough to extend onto the top

of a material support wing (I), use the adjustable stop (1) in its centered

conguration.

■ Narrow workpiece: If the workpiece does not extend across the gap

between the jig and the material support wing (I), use the adjustable stop(1)

in a side conguration.

Note For a side conguration, use whichever outer notch in the adjustable stop

arm will be farther from the jig after you place the adjustable stop (1) onto a

material support wing (I).

Note For instructions on changing the conguration, see Attach the

Adjustable Stop Arm to the Adjustable Stop Base onpage11.

15

I

1

A

I

Adjustable stop (1) in centered conguration

for wide workpiece

Adjustable stop (1) in side conguration

for narrow workpiece

b. Place the adjustable stop (1) onto the lid of a material support wing (I) so that:

■ The edge of the adjustable-stop arm (J) rests snugly against the workpiece.

■ The notch (2) on the underside of the adjustable stop base ts over the rail(3)

that runs across the lid of the material support wing (I).

c. Rotate the adjustable stop knob (K) clockwise until tight to secure the adjustable

stop (1) in position.

I

3

J

K

2

1

Note To reposition or remove the adjustable stop (1), rotate the adjustable stop

knob(K) counterclockwise to loosen it. Then slide the adjustable stop (1) to a new

position along the rail (3) or lift it off of the material support wing (I).

16

6

Drill Pocket Holes

WARNING When drilling, always ensure that the workpiece is clamped securely and

that the jig handle is pressed down to its travel limit.

a. Place your prepared drill bit (E) with stop collar (F) into your drill.

b. Insert your drill bit (E) into the drill guide (1) and bring your drill up to speed

before contacting the workpiece to ensure correct rotation of the drill bit.

c. Drill until the stop collar (F) stops going any deeper due to contact between the

stop collar (F) and drill guide (1). Remove the drill bit (E) from the drill guide (1)

while the drill bit is still rotating.

d. When you are nished drilling pocket hole(s), lift the jig handle to release the

clamping pressure; then remove your workpiece.

E

F

1

17

Operation - Drilling and Driving

Pocket-HoleScrews

For best results, follow these guidelines when drilling and driving pocket-hole screws:

■ Use the correct screw size according to this chart:

Gauged Material

Thickness

Easy-Set

Stop Collar

Material Thickness

Setting

Screw Length

1/2 Range 1/2

Automatic

1" (25 mm)*

3/4 Range 3/4 1-1/4" (32 mm)

3/4 1-1/2" (38 mm)

1-1/2 Range 1½ 2-1/2" (64 mm)

* A 1" screw is recommended for most applications, but if your workpiece

is on the low end of the range, a 3/4" screw might be required to keep

the screw tip from protruding.

Note If your material thickness falls in the range, use the same setup

techniques as the 3/4" range with a 1-1/2" screw. For more information on screw

selections, go to www.Kregtool.com/Screws or simply scan the QR code on the

side of your sample screw package.

■ Clamp joints in place to ensure a better nished joint. These examples show face

joints and edge joints.

WARNING When drilling, always ensure that the workpiece is clamped securely.

■ Place your screw on the driver tip (E), position the screw in the pocket hole, and

drive the screw until it is fully seated without overdriving.

E

18

Using Your Kreg Jig

Your Kreg Jig has been designed to work in either a vertical or horizontal orientation

to accommodate your workpiece.

To switch from one orientation to the other, simply rotate the jig 90degrees.

In either orientation, you can use the pocket-hole jig clamp (O) to secure the jig in

place on your workbench.

Orientation Description Clamp Position Options

Vertical Tool-storage side (1) is vertical One available clamp position (2)

Horizontal Tool-storage side (1) is face-down Two available clamp positions (3, 4)

1

2

O

Vertical

1

3

4

O

Horizontal

19

Removing the Jig from the Docking Station

If you use the 700-Series Jig with the optional docking station, you can remove the

jig from the docking station at any time.

Removing a Kreg 700-Series Jig fromaMountedDocking Station

With the jig handle (1) facing you, slide the jig (A) toward you until the jig(A)

disengages from the dock adapters (H). Then lift the jig (A) off the dock

adapters(H).

1

A

H

20

Removing a Kreg 700-Series Jig from an Unmounted Docking

Station

a. Detach each material support wing (I):

1. Grasp the material support wing (I) close to where it connects to the dock

adapter(H).

2. Gently lift up the material support wing (I) so that the material-support-wing

connector (1) pops out of the dock-adapter connector (2).

b. For the dock adapter (H) on each side of the jig (A):

1. Lift that side of the jig (A) slightly off the work surface.

2. With the jig handle (3) facing you, slide the dock adapter (H) away from you

until the dock adapter (H) disengages from the slot on the underside of the

jig(A).

3. Pull the dock adapter (H) out from the underside of the jig (A).

3

H

2

1

A

I

A

H

La page charge ...

Kreg Pocket-Hole Jig 720 Manuel utilisateur

Ce manuel convient également à

Kreg Pocket-Hole Jig 720 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents