MartinLogan Outdoor Living Foundation 8.1 System Manuel utilisateur

Register your warranty online at www.MartinLogan.com.

user’s manual

OUTDOOR LIVING

™

SERIES

111120

2

EN

|

TABLE OF CONTENTS

Overview............................3

Outdoor Living

™

Foundation Music System .........3

Contents of the System ......................3

Additional Required Components (Sold Separately) ...3

Required Tools ...........................3

Power .................................3

Planning the System Layout ..............4

Cable Recommendations ................5

Installation Considerations ...............5

Wiring & Speaker Installation ............6

Stereo Setup Using 4 Conductor Burial Cable

& Amplifier (Option 1) ......................6

Stereo Setup Using 4 Conductor Burial Cable

& Amplifier (Option 2) ......................7

Mono Setup Using 2 Conductor Burial Cable

& Amplifier (Option 3) ......................8

Preparing the 4 Conductor Burial Cable

(For Stereo Setup) .........................9

Preparing the 2 Conductor Burial Cable

(For Mono Setup) ........................10

Attaching Ground Stake to Speaker & Installation ...11

Cable Connections from Speaker to RED (+) and

BLACK (–) Burial Cable ....................12

Cable Connections from Speaker to WHITE (+) and

GREEN (–) Burial Cable ......................12

Cable Connections from Subwoofer to Burial Cable....13

Test System .........................14

To Avoid Speaker Damage ..............14

Listening Outdoors....................14

Limited Warranty.....................15

Serial Number | Numéro de série

3

|

EN

MartinLogan Outdoor Living

™

Foundation

Music System

The MartinLogan Outdoor Living Foundation Music System

includes 8 premium all-season outdoor speakers and 1 all-

season in-ground subwoofer ideal for backyards ranging

from 2,000 to 3,000 sq. ft.

Made of durable UV treated ABS plastic and thick high-

density polyethylene, the Outdoor Living Foundation Music

System can endure the elements while providing years of

trouble-free service.

While installation is relatively easy, MartinLogan’s Outdoor

Living Foundation Music System is designed to be installed

by your authorized MartinLogan dealer.

WARNING!

• ACCOUNT FOR POTENTIAL ELECTRICAL,

GAS, BURIED CABLES, PLUMBING OR

OTHER OBSTACLES BEFORE DIGGING.

• MANY LOCALITIES FORBID DIGGING

WITHOUT PRIOR NOTIFICATION.

CONTACT LOCAL AUTHORITIES BEFORE

INSTALLATION.

• READ AND FOLLOW ALL INSTRUCTIONS

BEFORE BEGINNING.

Contents of the System:

• (8) Speakers with Mounting Stakes

• (1) In-Ground Subwoofer with Canopy

• (20) Silicone-Filled Wire Connectors

Additional Required Components

(Sold Separately):

• Burial Speaker Cable

• Wire Ties (Optional)

Required Tools:

• Shovel

• Cable Strippers

Power

Any 8 ohm stereo amplifier (for Stereo Setup) or

Any 4 ohm mono amplifier (for Mono Setup)

OVERVIEW

4

EN

|

=

The MartinLogan Outdoor Living Foundation Music System

is designed to deliver seamless, and evenly distributed

sound coverage in an ‘open air’ environment. The following

illustration shows how a daisy chain of satellite speakers and

a subwoofer should be strategically placed to create even,

balanced coverage around the outdoor environment. The

satellite speakers should be spaced from 6 to 10 feet (2.4 -

3 meters) apart for optimal coverage. With a tighter spacing,

more satellites will be required to fill out an area, but with the

advantage of more consistent coverage and volume levels

across the intended entertainment area.

To achieve the best balance between the satellites and

subwoofer, the subwoofer should be placed as close to the

center of the satellites as possible. Keep in mind that this

is simply a suggestion and that your unique environment

may dictate otherwise. If more bass is desired, placing the

subwoofer near a wall or other solid surface will greatly

reinforce the low bass frequencies.

Checklist:

q Identify the location.

q Determine the positioning of the satellite speakers

and subwoofer.

q Dig the trench according to satellite speakers and

subwoofer to be installed.

q The trench should be 6”- 8” deep.

PLANNING THE SYSTEM LAYOUT

5

|

EN

We strongly recommend using burial-rated cable (not

included) when installing the Outdoor Living Foundation

Music System. In addition, it’s critical to use the proper

speaker cable gauge. Please review the chart below.

There are a few considerations before you start digging a trench:

• Ensure that your ENTIRE system is tested prior to installation.

• Ensure that the proposed area is easily accessed and that

the area is not prone to flooding, standing water or where

the speakers and subwoofer can be easily damaged,

kicked or struck.

• Consider overall landscape/garden design and

positioning in relation to the listening area.

CABLE RECOMMENDATIONS

INSTALLATION CONSIDERATIONS

CABLE GAUGE CHART

Cable Gauge Distance

18 Gauge Up to 100 feet (30 meters)

16 Gauge Up to 150 feet (45 meters)

14 Gauge Up to 200 feet (61 meters)

12 Gauge Up to 400 feet (122 meters)

6

EN

|

WIRING & INSTALLATION

Stereo Setup Using 4 Conductor Burial Cable & Amplifier (Option 1)

Left

8 Ohm Stereo 2-Channel Amplifier

Right Left Right

Left & Right

Stereo Wiring Diagram (Option 2)

Left Right Left Right

4 Conductor Burial Wire

–

+

–

+

Black Red

Green White

+

–

+

4 Conductor Burial Wire

–

+

–

+

Black Red

Green White

+

–

+

Left

8 Ohm Stereo 2-Channel Amplifier

Left Left Left

Left & Right

Stereo Wiring Diagram (Option 1)

Right Right Right Right

The satellite speakers included in this system individually

present a 32 ohm load to the amplifier. When 4 of them

are connected on each amplifier channel in parallel,

the load to the amplifier is approximately 8 ohms. The

nominal impedance of the subwoofer is 8 ohms per

channel. The satellites and subwoofer feature optimized

internal crossovers so that the subwoofers impedance is not

combined with the satellites. The overall load presented to

your amplifier by the combined system of 8 satellites and 1

subwoofer will be around 8 ohms nominal per channel.

With these considerations in mind, multiple system wiring

possibilities are possible. The following diagrams are

simple, and safe examples of wiring the system to a

traditional 8 ohm stereo amplifier. If using an alternative

wiring or amplification configuration, please take care to

ensure that the impedance presented to your amplifier is

within its published specifications. Failure to adhere to the

above guidance could result in damage to the speakers

and/or the amplifier which MartinLogan will not take

responsibility for and will not be covered under warranty.

7

|

EN

Stereo Setup Using 4 Conductor Burial Cable & Amplifier (Option 2)

WIRING & INSTALLATION (CONT’D)

Left

8 Ohm Stereo 2-Channel Amplifier

Right Left Right

Left & Right

Stereo Wiring Diagram (Option 2)

Left Right Left Right

4 Conductor Burial Wire

–

+

–

+

Black Red

Green White

+

–

+

4 Conductor Burial Wire

–

+

–

+

Black Red

Green White

+

–

+

Left

8 Ohm Stereo 2-Channel Amplifier

Left Left Left

Left & Right

Stereo Wiring Diagram (Option 1)

Right Right Right Right

8

EN

|

Mono Setup Using 4 Conductor Burial Cable & Amplifier (Option 3)

Mono

4 Ohm Mono 1-Channel Amplifier

Mono Mono Mono

Mono

Mono Wiring Diagram (Option 3)

Mono Mono Mono Mono

2 Conductor Burial Wire

Black Red

+

–

+

To Sub

To Adjoining Amp,

Sub or Speaker

To Adjoining,

Sub or Speaker

9

|

EN

Preparing the 4 Conductor Burial Cable (For Stereo Setup)

3. Use a round

cable stripper to

remove the outside

protective cable

jacket to expose

the four color-

coded wires.

Separate the wire

loops as shown.

2. Recommended:

Use a wire tie

(not included) to

keep the wire

loop intact and

it will act as a

strain relief.

4. Cut the red (+)

and black (-)

OR white (+)

and green (-)

wires with cable

strippers and

strip off 1 inch

(25.4 mm) of

insulation to

expose the bare

wire conductor.

white (+) &

green (-)

red (+) &

black (-)

1. Starting with the

first speaker and

every speaker/

sub that comes

after, create a

loop approximate-

ly 6” in length.

WIRING & INSTALLATION (CONT’D)

10

EN

|

Preparing the 2 Conductor Burial Cable (For Mono Setup)

1. Starting with the

first speaker and

every speaker/

sub that comes

after, create a

loop approximate-

ly 6” in length.

3. Use a round

cable stripper to

remove the outside

protective cable

jacket to expose

the two color-

coded wires.

Separate the

wire loops

as shown.

2. Recommended:

Use a wire tie

(not included) to

keep the wire

loop intact and

it will act as a

strain relief.

4. Cut the red (+)

and black (-)

wires with cable

strippers and

strip off 1 inch

(25.4mm) of

insulation to

expose the bare

wire conductor.

red (+)

black (-)

11

|

EN

Attaching Ground Stake to Speaker & Installation

3. By hand, push the

speaker assembly

into the ground.

CAUTION:

DO NOT use

a hammer.

4. The speaker is

now installed.

The next step is

wiring, go to the

next page for

instructions.

2. To attach the

speaker to the

ground stake,

hand thread the

speaker to the

ground stake.

1. Thread the

speaker’s wiring

down through

the ground stake

and out of the

wiring hole

as shown.

WIRING & INSTALLATION (CONT’D)

12

EN

|

Cable Connections from Speaker to RED (+) AND BLACK (-) Burial Cable

Cable Connections from Speaker to WHITE (+) AND GREEN (-) Burial Cable

To Speaker

To Adjoining

Amp, Sub or

Speaker

To Adjoining

Amp, Sub or

Speaker

To Adjoining,

Sub or Speaker

To Adjoining,

Sub or Speaker

Before you start wiring, please refer to the

wiring setup options on pages 6 to 8. Combine

and twist (clockwise) the Red wire (as shown in the diagram)

from a speaker or subwoofer to the Red wires from the burial

cable. Secure these three wires using the provided silicone-

filled wire connector; Repeat this procedure for the Black

wires. NOTE: You may have to cut some of the speaker cable

emanating from the speaker to a more manageable size.

Before you start wiring, please refer to the

wiring setup options on pages 6 to 8. Combine

and twist (clockwise) the Red wire (as shown in the diagram)

from a speaker or subwoofer to the White wires from the

burial cable. Secure these three wires using the provided

silicone-filled wire connector; Repeat this procedure for the

Black and Green wires. NOTE: You may have to cut some

of the speaker cable emanating from the speaker to a more

manageable size.

13

|

EN

Cable Connections from Subwoofer to Burial Cable

To Sub

To Adjoining Amp,

Sub or Speaker

To Adjoining,

Sub or Speaker

Before you start wiring, please refer to the

wiring setup options on pages 6 to 8. Combine

and twist (clockwise) the Red wire (as shown in the diagram)

from a speaker or subwoofer to the Red wires from the burial

cable. Secure these three wires using the provided silicone-

filled wire connector; Repeat this procedure for the Black,

Green and White wires. NOTE: You may have to cut some

of the speaker cable emanating from the subwoofer to a

more manageable size.

WIRING & INSTALLATION (CONT’D)

14

EN

|

TEST SYSTEM

After all satellites and subwoofer connections are completed,

connect the wires to your receiver or amplifier.

IMPORTANT: Be sure not to let any stray ’+’ and

’-’ strands touch each other. Touching strands

will cause a short circuit that could damage your

amplifier.

Turn your receiver or amplifier ‘On’ and test the system with your

favorite music. If your system is operating properly, refill the wire

trench and enjoy your new speakers.

Contrary to popular belief, most speaker damage and

distortion occurs from using an amplifier with too little

power. The more available power an amplifier has, the

higher the threshold becomes before clipping occurs

(outputting damaging distortion), effectively raising

the useable volume of the system. Of course, going

overboard with power can allow the listener to exceed

the mechanical limits of the speakers and result in

speaker damage and distortion. However, when used

appropriately, a more powerful amplifier can reduce the

risk of distortion or speaker damage as the amplifier will

be able to continuously operate within

its intended “safe range” during normal playback of

the system.

If your speakers begin to sound harsh or grating, or if

you hear the bass breaking up, turn the volume down

immediately or you will damage your speakers! This type

of damage constitutes abuse and is not covered under

warranty.

Tone controls and equalizers can demand even more

power from an amplifier, lowering the point at which it

produces clipping distortion. Use them sparingly, if at all,

and avoid using them when listening at loud levels.

For areas larger than 3,000 sq. ft., we recommend using

multiple MartinLogan Outdoor Living Foundation systems.

Please note that powering multiple Outdoor Living Foundation

systems may require additional amplification to properly

integrate. Please consult your dealer for guidance on

amplifier capability and selection. Using more speakers

ensures that sound is not only more evenly distributed, but

also allows the system to be more easily heard at lower

listening levels. By doing this, demand on the amplifier is

reduced and neighbors are not disturbed. Think of it this

way: When lighting a large outdoor area, using multiple

floodlights on a dimmer set to a low setting is far more

effective than using a single floodlight with the dimmer

set to high.

TO AVOID SPEAKER DAMAGE

LISTENING OUTDOORS

15

|

EN

The MartinLogan

®

Outdoor Living Foundation Music System

is warranted to be and remain free of manufacturing and/

or material defects for a period of three (3) years from the

date of original purchase. Within the time period specified,

repair, replacement or adjustment of parts for manufacturing

and/or material defects will be free of charge to the original

owner. Thermal or mechanical abuse/misuse is not covered

under warranty.

Limitations:

• Warranty begins on date of original retail purchase

from an Authorized MartinLogan

®

Dealer only. It is not

transferable.

• Warranty applies to product in normal residential use only.

If product is subjected to any of the conditions outlined in

the next section, warranty is void.

• Warranty does not apply if the product is used in

professional or commercial applications.

• Warranty also excludes normal cosmetic deterioration

caused by environmental conditions.

Warranty is Void if:

• The product has been abused (intentionally or

accidentally).

• The product has been used in conjunction with unsuitable

or faulty equipment.

• The product has been subjected to damaging signals,

derangement in transport, mechanical damage or any

abnormal conditions.

• The product (including cabinet) has been tampered with or

damaged by an unauthorized service facility.

• The serial number has been removed or defaced.

Owner Responsibilities:

• Provide normal/reasonable operating care and

maintenance.

• Provide or pay for transportation charges for product to

service facility.

• Provide proof of purchase (your sales receipt given at time

of purchase from your Authorized MartinLogan

®

Dealer

must be retained for proof-of-purchase date).

Should servicing be required, contact your nearest Authorized

MartinLogan

®

Dealer, MartinLogan Ltd. or Import Distributor

(outside the U.S. and Canada) to arrange, bring in or

ship prepaid, any defective unit. Visit our website,

www.martinlogan.com for more information.

MartinLogan Ltd. reserves the right to improve the design of

any product without assuming any obligation to modify any

product previously manufactured.

This warranty is in lieu of all other warranties expressed or

implied, of merchantability, fitness for any particular purpose

and may not be extended or enlarged by anyone. In no

event shall MartinLogan Ltd., their agents or representatives

be responsible for any incidental or consequential damages.

Some jurisdictions do not allow limitation of incidental or

consequential damages, so this exclusion may not apply

to you.

Retain this manual and your sales receipt for

proof of warranty term and proof of purchase.

LIMITED WARRANTY

NOTES

g u i d e d e l ’ u t i l i s a t e u r

SYSTÈME D’ENCEINTES

MUSICALES D’EXTÉRIEUR

Inscrivez votre garantie en ligne à l’adresse www.MartinLogan.com.

SÉRIE OUTDOOR LIVING

™

par

111120

La page est en cours de chargement...

MartinLogan Outdoor Living Foundation 8.1 System Manuel utilisateur

MartinLogan Outdoor Living Foundation 8.1 System Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents