Fire Magic E1060S4EAP71 Guide d'installation

Marque: Fire Magic

Modèle: E1060S4EAP71

Catégorie: Barbecues

Taper: Guide d'installation

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

outdoor gas grill must be installed in accordance

with local codes and ordinances, or, in the absence

of local codes, with the latest National Fuel Gas

Code (ANSI Z223.1/NFPA 54), or Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shutoff valve during any pressure testing

of the gas-supply system at pressures up to and

including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

SAFETY AND WARNING CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁ re department.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information,

consult a qualiﬁ ed professional installer,

service agency, or the gas supplier.

WARNINGS AND SAFETY CODES

10-32

OUTDOOR STAND-ALONE GAS GRILL

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

E660s, E790s, and E1060s

Proper operation of your grill requires

prompt and periodic maintenance. See

the CARE & CLEANING section for

details.

REV 5 - 1412090835

L-C2-330

ECHELON

diamond series

E790s shown

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION

ECHELON GRIL EXTÉRIEUR DE GAZ DU PORTATIF

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez l’admission de gaz de

I’appariel.

2. Éteindre toute ﬂ amme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, éloignez-vous de

l’appareil et appelez immédiatement

le fournisseur de gaz ou le service

d’incendie.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂ ammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂ ant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

sifﬂ ant par fermeture que ses différents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

Certiﬁ é à la norme ANSI : Z21.58b-2012 / CSA 1.6b-2012

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce

manuel. Pour l’aide ou l’information

additionnelle, consultez un installateur

professionnel qualiﬁ é, l’agence de service,

ou le fournisseur de gaz.

SÛRETÉ ET CODES D’AVERTISSEMENT

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface

combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et

l’arriére de l’appareil et la construction combustible (45.7

cm à partir des parois latérales et 45.7cm à partir de

l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

REV 5 - 1412090835

L-C2-330

CONTENTS

To protect against electric shock, do not immerse cord or plugs in water or other liquid;

Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off

parts;

Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair;

Do not let the cord hang over the edge of a table or touch hot surfaces;

Do not use an outdoor cooking gas appliance for purposes other than intended;

When connecting, ﬁ rst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet;

Use only a Ground Fault Circuit Interrupter (GFCI) protected receptacle with this outdoor cooking gas

appliance;

Never remove the grounding plug or use with an adapter of 2 prongs.

Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and

approved for outdoor use with a W-A marking.

ELECTRICAL SAFETY

REV 5 - 1412090835

L-C2-330

4 REPLACEMENT COMMON PARTS LIST

SINGLE SIDEBURNER UNIQUE PARTS LIST

7 DOUBLE SIDEBURNER UNIQUE PARTS LIST

8 POWER BURNER UNIQUE PARTS LIST

9 ELECTRICAL CONNECTIONS

9 GRILL MAINTENANCE AND SAFETY INFORMATION

9 MASTER SWITCH

10 MODEL SPECIFICATIONS TABLE

11 BUILT-IN GRILL WIRING DIAGRAM

12 STAND-ALONE GRILL DIMENSIONS TABLE

13 INSTALLATION REQUIREMENTS

14 ENSURE PROPER COMBUSTION AIR AND COOLING AIRFLOW

15 LOCATION PREPARATION

15 WHEELS AND CASTERS

15 CONNECT THE GAS SUPPLY

15 INSTALLATION

16 INSTALL ZONE DIVIDERS

17 INSTALL THE SIDEBURNER SHELF (IF EQUIPPED)

18 SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

20 IDENTIFICATION OF GRILL CONTROLS

21 OPTIONAL POWER HOOD

23 LIGHTING (IGNITION) INSTRUCTIONS

24 DIGITAL THERMOMETER / INTERIOR AND KNOB LIGHTS

27 ROTISSERIE INSTRUCTIONS

28 USING THE FOLDING SHELF

28 REMOVING DRAWERS

29 POWER BURNER

30 OPTIONAL INFRARED BURNER OPERATION

31 GRILLING TIPS

32 ACCESSORIES

33 FIRE MAGIC

DRIP TRAY

34 CARE & CLEANING

35 REPLACING HALOGEN BULBS

36 POWER SUPPLY FUSE REPLACEMENT

37 CONVERTING THE GAS TYPE

40 BURNER AIR SHUTTER ADJUSTMENT

43 DOUBLE SIDEBURNER

45 CONTROL PANEL REMOVAL

46 NOTES PAGE

47 TROUBLESHOOTING

48 WARRANTY

REPLACEMENT COMMON PARTS LIST

Fig. 4-1

To order replacement

parts, contact your local

Fire-Magic dealer.

Items in light gray are

not available on all

models.

E660s & E790s grills are

equipped with two drawers

on the right side of the unit.

Some items shown

are optional, or are

not available for

certain models. Your

model may vary, refer

to parts list.

REV 5 - 1412090835

L-C2-330

REPLACEMENT COMMON PARTS LIST (cont.)

REV 5 - 1412090835

L-C2-330

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Stainless cooking grid (set of 2 or 3) 3544-S-3 1 3539-S-3 1 23539-S-2 2

Flavor grid (set of 3 or 4) 3057-S-3 1 3056-S-3 1 3056-S-4 1

Main burner 3041-50 3 3041-50 3 3041-50 4

Heatshield kit 24177-05 3 24177-05 3 24177-05 4

Silicone gasket 24177-06 3 24177-06 3 24177-06 4

Infrared burner * 3050 1 3050 1 3050 1

Oven lid 23738-53 1 23745-53 1 23747-53 1

Oven lid w/ window 24193-54 1 24188-54 1 24183-54 1

Window (only)*‡ 24187-45 1 24187-45 1 24187-45 1

Warming rack 36735-M 1 36755-M 1 36745-M 1

10.

Back burner assembly 24794-02 1 24789-02 1 24784-02R/L 1

11.

Back burner cover 24794-010 1 24789-010 1 24784-010 2

12.

Zone separator 3061-S 2 3061-S 2 3061-S 3

13.

Heavy-duty rotisserie motor 3600-05M 1 3600-05M 1 3600-05M 1

14.

Heavy-duty rod 3606-40 1 3609-40 1 3607-40 1

15.

Heavy-duty rod knob 24187-16 1 24187-16 1 24187-16 1

16.

Meat holder (pair) 3613 1 3613 1 3613 1

17.

Counterbalance 3620E 1 3620E 1 3620E 1

18.

Grid lifter 3519 1 3519 1 3519 1

19.

Convertible regulator PR-4 1 PR-4 1 PR-4 1

20.

Control panel w/ back burner and raceway † 24394-47 1 24389-47 1 24384-47 1

Control panel w/ back burner, raceway, and

wire harness †

24394-49 1 24389-49 1 24384-49 1

21.

Valve manifold w/ back burner 24393-22 1 24388-22 1 24383-22 1

22.

Small knob 24182-42 2 24182-42 2 24182-42 3

23.

Large knob 24182-41 3 24182-41 3 24182-41 4

24.

LED disk (small) 24182-64 2 24182-64 2 24182-64 3

25.

LED disk (large) 24182-63 3 24182-63 3 24182-63 4

26.

Digital thermometer 24182-12 1 24182-12 1 24182-12 1

27.

Meat probe 24187-14S 1 24187-14S 1 24187-14S 1

28.

Power supply w/ outlet † 24387-18 1 24387-18 1 24387-18 1

29.

Drip tray 3087 1 3087 1 3087 1

30.

Drip tray liner (set of 4) 3557 1 3557 1 3557 1

31.

Wire harness for raceway ‡ 24194-47 1 24189-47 1 24184-47 1

32.

Back burner electrode *‡ 4199-52 1 4199-52 1 4199-52 2

* If equipped

‡ Not shown

† Add (M) to part number for power hood

REPLACEMENT COMMON PARTS LIST (cont.)

REV 5 - 1412090835

L-C2-330

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

33.

Electrode‡ 3199-72 3 3199-72 3 3199-72 4

34.

Thermometer wire harness ‡ 24187-13 1 24187-13 1 24187-13 1

35.

Natural gas oriﬁ ce(s) ‡ 3001-42-3 1 3001-38-3 1 3001-40-4 1

36.

Natural back burner gas oriﬁ ce(s) ‡ 3001-53-1 1 3001-51-1 1 3001-53-2 1

37.

Propane gas oriﬁ ce(s) ‡ 3001-54-3 1 3001-53-3 1 3001-53-4 1

38.

Propane back burner gas oriﬁ ce(s) ‡ 3001-63-1 1 3001-57-1 1 3001-63-2 1

39.

Natural smoker oriﬁ ce ‡ 3003-68-1 1 3003-68-1 1 3003-68-1 1

40.

Propane smoker oriﬁ ce ‡ 3003-77-1 1 3003-77-1 1 3003-77-1 1

41.

Wood chip box assembly 24182-45 1 24182-45 1 24182-45 1

42.

12v / 10 watt halogen bulb ‡ 24187-15 2 24187-15 2 24187-15 3

43.

Light lens ‡ 24187-26 2 24187-26 2 24187-26 3

44.

Lamp assembly ‡ 24187-28 2 24187-28 2 24187-28 3

45.

Power hood motor assembly * 24183-18 1 24183-18 1 24183-18 1

46.

Power hood rocker switch * 24187-39 1 24187-39 1 24187-39 1

47.

Lighted master shut-off switch 24182-46 1 24182-46 1 24182-46 1

48.

Light microswitch 24187-20 1 24187-20 1 24187-20 1

Power hood light & motor microswitch 24187-44 1 24187-44 1 24187-44 1

49.

Flash tube (left) ‡ 24187-29 1 24187-29 1 24187-29 1

50.

Flash tube (right) ‡ 24187-35 2 24187-35 2 24187-35 3

51.

Flex connector ‡ 3030-08 1 3030-08 1 3030-08 1

52.

Tool holder 25387-12 1 25387-12 1 25387-12 1

53.

Paper towel holder 25387-11 1 25387-11 1 25387-11 1

54.

Propane tank tray

(propane models only)

25386-21 1 25386-21 1 25386-21 1

55.

Propane regulator with hose

(propane models only)

5110-15 1 5110-15 1 5110-15 1

56.

Quick-disconnect hose ‡

(natural models only)

5110-03 1 5110-03 1 5110-03 1

57.

Power cord ‡ 25387-13 1 25387-13 1 25387-13 1

58.

Folding shelf 24336-15 1 24336-15 1 24336-15 1

59.

Fire Magic

cookbook ‡ 3595 1 3595 1 3595 1

* If equipped

‡ Not shown

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

60.

Sideburner (burner only) ‡ 3279-32 1 3279-32 1 3279-32 1

61.

Sideburner assembly w/ shelf 24336-16 1 24336-16 1 24336-16 1

62.

Sideburner grid 3552 1 3552 1 3552 1

63.

Sideburner cap 3275-36 1 3275-36 1 3275-36 1

64.

Sideburner lid 24336-31 1 24336-31 1 24336-31 1

‡ Not shown

SINGLE SIDEBURNER UNIQUE PARTS LIST

DOUBLE SIDEBURNER UNIQUE PARTS LIST

Fig. 7-1

Note: See page 4-6 for common part

and number identification.

Some quantities may vary.

Grills equipped with a double

sideburner are available for 660s,

790s, and 1060s series.

1060s shown here.

REV 5 - 1412090835

L-C2-330

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

20.

Main control panel w/ raceway † 34394-13 1 34389-13 1 34384-13 1

Main control panel w/ raceway and wire harness † 34394-18 1 34389-18 1 34384-18 1

21.

Main valve manifold 24193-22 1 24188-22 1 24383-28 1

60.

Double sideburner valve manifold 3281-22 1 3281-22 1 3281-22 1

61.

Double sideburner (only) ‡ 3279-32 2 3279-32 2 3279-32 2

62.

Double sideburner grid 3529-S 1 3529-S 1 3529-S 1

63.

Sideburner cap 3275-36 2 3275-36 2 3275-36 2

64.

Double sideburner cover 3281-07 1 3281-07 1 3281-07 1

65.

Convertible regulator

(for double sideburner valve manifold)

PR-4 1 PR-4 1 PR-4 1

66.

Double sideburner control panel N/A N/A 23281-12 1

67.

Double sideburner wire harness extension ‡ 34394-19 1 34394-19 1 34394-19 1

* If equipped

‡ Not shown

† Add (M) to part number for power hood control panel

POWER BURNER UNIQUE PARTS LIST

Fig. 8-1

Note: See page 4-6 for common part

and number identification.

Some quantities may vary.

REV 5 - 1412090835

L-C2-330

E1060s

Item Description Part No. Qty.

20.

Main control panel w/ raceway † 34384-14 1

Main control panel w/ raceway and wire harness † 34384-18 1

21.

Main valve manifold 24383-28 1

60.

Power burner valve manifold 3278-14 1

61.

Power burner (only) 3278-01B 1

62.

Power burner grid - stainless steel 3545-S 1

Power burner grid - porcelain cast 3545 1

63.

Power burner collimator 3279-09 1

64.

Power burner cover 3278-06 1

65.

Convertible regulator

(for power burner valve manifold)

PR-4 1

66.

Power burner control panel 23278-10 1

67.

Power burner wire harness extension ‡ 34384-19 1

* If equipped

‡ Not shown

† Add (M) to part number for power hood control panel

ELECTRICAL CONNECTIONS

This grill requires 120VAC power to opperate.

Plug the power supply cord into a properly wired

and inspected GFCI electrical receptacle (15 AMP

minimum). Use a heavy-duty grounded extension

cord if necessary.

WARNING

Electrical Grounding Instructions

For your protection against shock hazard, this

outdoor-cooking gas-appliance is equipped with

a three-pronged (grounding) electrical connector.

This appliance should be connected to a properly

grounded three-prong receptacle using a grounding

extension cord rated for outdoor use. Do not cut or

remove the grounding prong from the connector.

Important: ONLY REPLACE THE OVEN LIGHTS

WITH 12V / 10 WATT HALOGEN BULB(S).

1. The outdoor grill and surrounding area MUST

remain clear of ﬂ ammable substances such as

gasoline, yard debris, wood, etc.

2. The airﬂ ow through the vent space located below

the control panel must remain unobstructed.

3. When using propane gas:

a. The required ventilation openings in the

enclosure must be clear of debris.

b. The propane cylinder, regulator, and rubber

hose must be in a location not subject to

temperature above 125° F (51° C).

4. The ﬂ ames on each burner burn evenly along

the entire burner with a steady ﬂ ame (mostly

blue). If burner ﬂ ames are not normal, check

and clean the oriﬁ ce and burner/venturi tubes

for insects and insect nests. A clogged tube can

lead to a ﬁ re beneath the grill. A proper ﬂ ame

pattern will ensure safe operation and optimal

performance. Adjust the air shutter as needed

(see AIR SHUTTER ADJUSTMENT).

5. The in-line gas valve or gas cylinder valve must

always be shut OFF when the grill is not in use.

6. The drip collector holes must be clear and

unobstructed. Excessive grease deposits can

result in a grease ﬁ re.

7. The back burner, sideburner, or IR burner cover

must be removed before using the burner.

8. Whenever reconnecting any wires, apply a

small amount of dielectric grease to the male

connector, then make the connection.

GRILL MAINTENANCE AND SAFETY INFORMATION

WARNING: NEVER cover the entire cooking or grill surface with griddles or pans. Overheating will occur, and

burners will not perform properly when combustion heat is trapped below the cooking surface.

CAUTION: NEVER spray water on a hot gas unit.

The grill serial identiﬁ cation number is located on the underside of the drip tray handle. It

is recommended that the drip tray ﬁ rst be removed and cleaned / emptied of its contents,

then turned over to view. The unit rating label is located inside of the control panel.

REV 5 - 1412090835

L-C2-330

MASTER SWITCH

The master switch is push button operated, and is

located on the right side of the control panel (see

Fig. 9-1). It controls the power to all lights, igniters,

and the thermometer. It allows the power to be

turned on or off for safety and convenience. The

switch will need to be turned on prior to each grill

use, and turned off after each use.

Master

switch

Fig. 9-1

MODEL SPECIFICATIONS TABLE

Table 1 E660s E790s E1060s

Main burner quantity

N/P oriﬁ ce drill size

#42 / #54

#38 / #53

#40 / #53

Back burner quantity

N/P oriﬁ ce drill size

#53 / #63

#51 / #57

#53 / #63

Single sideburner *

N/P oriﬁ ce drill size

#50 / #58 #50 / #58 #50 / #58

Double sideburner quantity*

N/P oriﬁ ce drill size

#50 / #58

Smoker drawer burner

N/P oriﬁ ce drill size

#68 / #77 #68 / #77 #68 / #77

Infrared searing burner *

N/P oriﬁ ce drill size

#45 / #55 #45 / #55 #45 / #55

Power burner *

Left N/P oriﬁ ce drill size

Right N/P oriﬁ ce drill size

- -

#30 / #50

#46 / #1.25

GFCI Receptacle Rating 120VAC / 10A Max

Power Supply Rating 120VAC / 1.5A / 60 Hz

Oven Lights Rating 12V / 10 watt halogen bulb

If equipped

REV 5 - 1412090835

L-C2-330

MODEL SPECIFICATIONS (cont.)

Note: In addition, a wire diagram speciﬁ c to your unit

can be found afﬁ xed to the inside of the control

panel.

STAND-ALONE GRILL WIRING DIAGRAM*

E1060s model shown. Model wire diagrams may vary.

REV 5 - 1412090835

L-C2-330

Power supply

Wire harness

assembly

Valve

manifold

Master

switch

Main burner igniters

Backburner

igniter

Left oven

light

Digital

thermometer

Oven light

micro switch

(not used for

Magic View)

Meat

probe

jack

Thermocouple

Back

burner

Main

burner 1

Main

burner 2

Main

burner 3

Center oven

light

Right oven

light

Backburner

igniter

Smoker

igniter

For Magic

View only

Main

burner 4

Smoker

burner

Back

burner

LED disc

(small)

LED disc

(large)

sideburner

igniter

Side

burner

Thermometer

wire harness

MODEL SPECIFICATIONS (cont.)

STAND-ALONE GRILL DIMENSIONS TABLE

Model Series

Height Width Depth

Floor to top

(with oven)

Floor to top

of shelf

(C)

Left to right Front to back

Cart base

(D)

(with shelves)

Cart base

(G)

Maximum

outer

(H)

Open

(A)

Closed

(B)

(E)

1 Up / 1 Down

(F)

E660s

w/ or w/o sIngle

sideburner

/8" 52" 37" 34

/4" 67

/2" 56" 26" 29

/4"

E660s

w/ double sideburner 60

/8" 52" 37" 53" 86

/4" 77" 26" 29

/4"

E790s

w/ or w/o sIngle

sideburner

/8" 52" 37" 40" 73

/4" 59

/4" 26 " 29

/4"

E790s

w/ double sideburner 60

/8" 52" 37" 58

/4" 92" 80

/4" 26" 29

/4"

E1060s

w/ or w/o sIngle

sideburner

/8" 52" 37" 53" 86

/4" 66

/4" 26 " 29

/4"

E1060s

w/ double sideburner

or Power burner

/8" 52" 37" 77

/4" 111" 93

/4" 26" 29

/4"

REV 5 - 1412090835

L-C2-330

INSTALLATION REQUIREMENTS

Installation must be performed by a qualiﬁ ed professional

service technician.

This grill is designed for outdoor use only. DO NOT use this grill

inside a building, garage, enclosed area, or under any overhead

construction.

DO NOT use this grill in or on a recreational vehicle or boat.

Important: The grill is not insulated. Refer to the information

below to ensure all required clearances are met.

The grill must have a minimum clearance of 18" from

combustible materials/items AT ALL TIMES.

Side and Rear Wall Clearances

For the minimum clearances between the grill and any side or rear

walls, your setup must fall within one (or more) of the following:

A. Clearance between grill and combustible wall

• The grill must have a minimum of 18" right, left, and rear

clearance from any combustible wall (see Fig. 13-1).

B. Clearance between grill and strictly non-combustible wall

(i.e. brick wall, see Fig. 13-2)

• The grill must have a minimum of 4" right, left, and rear

clearance from any non-combustible wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

Fig. 13-1 Clearance 'A' Diagram

Combustible

Min.

18"

(Clearance required for

right, left, and rear)

Fig. 13-2 Clearance 'B' Diagram

Non-combustible

Min.

(Clearance required for

right, left, and rear)

REV 5 - 1412090835

L-C2-330

INSTALLATION REQUIREMENTS (Cont.)

The control panel MUST remain removable for

servicing and air shutter adjustment (see PARTS

LIST).

THIS UNIT MUST NOT BE LOCATED IN A FULLY

ENCLOSED AREA OF ANY KIND.

ENSURE PROPER COMBUSTION AIR AND

COOLING AIRFLOW

Proper airﬂ ow (Fig. 14-1) MUST be maintained for

the grill to perform as it was designed. If airﬂ ow

is blocked, overheating and poor combustion will

result. Do not block the 1" (2.5 cm) front air inlet

along the bottom of the control panel or more

than 75% of the cooking grid surface with pans

or griddles.

Note: The 1" (2.5 cm) front air space also allows

access to the drip tray.

Fig. 14-1 - Ventilation

CAUTION: Wind blowing into or across the rear

oven lid vent (Fig. 14-2) can cause

poor performance and/or dangerous

overheating. Orient the grill so that the

prevailing wind blows toward the front

of the grill (Fig. 14-3).

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" (17.78 cm) water column

(w.c.), minimum 5" (12.7 cm), maximum 10

" (26.7

cm). For propane gas - normal 11" w.c., minimum 10"

(25.4 cm), maximum 13" (33 cm).

Fig. 14-3

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

YOU MUST PROTECT REAR OVEN

VENT FROM PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 14-2

REV 5 - 1412090835

L-C2-330

INSTALL THE TOOL HOLDER AND

PAPERTOWEL HOLDER

The rectangular mounting bracket for the tool

holder and the paper towel holder come pre-

attached to the sides of the cart.

Unpack the holder portion, squeeze the open

ends together slightly, and install them into the

mounting bracket (see Fig. 15-2). Next, release

the hanger so that the ends extend out through

the holes in the top and bottom of the mounting

bracket (Fig. 15-3, 15-4).

When not in use, the racks may be folded back

against the wall of the grill (Fig. 15-3, 15-4).

LOCATION PREPARATION

Prepare a ﬂ at, level surface capable of supporting

the weight of the stand-alone grill and convenient to

the gas supply if connecting to a gas line.

WHEELS AND CASTERS

To lock a caster press down on the side of the lever

with the word "ON" stamped on it until it stops and

the caster will not turn. To unlock, press down on the

side stamped "OFF."

INSTALLATION

Fig. 15-1

Fig. 15-2

Fig. 15-4

Fig. 15-3

CONNECT THE GAS SUPPLY

For connecting a propane unit to a portable

propane tank, read the safety warnings and

follow the instructions in the section SAFE USE

AND MAINTENANCE OF PROPANE GAS

CYLINDERS.

For household propane or natural gas units:

a. Turn OFF the gas supply at the source. The

quick disconnect hose is pre-installed on the

valve manifold at the manufacturer. Run the

hose through the hole in the bottom rear of the

stand-alone unit, to the gas supply. Connect

the

" NPT socket at the end of the hose to

the gas supply. Use pipe joint compound that is

resistant to all gasses on the male pipe ﬁ tting

and tighten securely. DO NOT use pipe joint

compound to connect the ﬂ are ﬁ ttings.

c. Turn all burner valves to the OFF position. Turn

the gas supply on. Then carefully check all gas

connections for leaks with a brush and soapy

water before lighting. NEVER USE A MATCH

OR OPEN FLAME TO TEST FOR LEAKS.

REV 5 - 1412090835

L-C2-330

INSTALLATION (cont.)

Fig. 16-1

Zone divider

Groove

Front

INSTALL THE FLAVOR GRIDS

Place the ﬂ avor grids directly onto the studs on the

burners. The panels allow heat from the burners to

be evenly distributed throughout the cooking area.

The panels are stainless steel and will heat and cool

quickly, making your barbecue very responsive to

the changes you specify in grill temperature. They

are rust resistant and may be cleaned with standard

oven cleaners. Some discoloring will be seen with

use. This is normal for stainless steel and does not

affect the function.

Fig. 16-2 Install ﬂ avor grids

Place onto studs

Fig. 16-1 Install zone dividers

REV 5 - 1412090835

L-C2-330

INSTALL ZONE DIVIDERS

Place the zone dividers as shown (Fig. 16-1) into the

grooves in the inner ﬁ rewall of the grill to allow for

maximum heat control and thermometer accuracy in

each zone. Remove and store during rotisserie use.

This shelf comes separate from the grill for

convenience in shipping. The sideburner

shelf must be installed using the following

instructions before hooking up the grill to a

gas source.

INSTALL THE SIDEBURNER SHELF

1. Remove the protective plastic from the grill,

sideburner, and sideburner lids by carefully

peeling it off with your fingers. Do not use

tools.

2. Hold the sideburner shelf up against the left

side wall of the grill so that the holes in the shelf

line up with the four (4) threaded screw holes

in the side wall and the air-shutter end of the

sideburner venturi tube ﬁ ts around the brass

oriﬁ ce protruding from the side of the cart.

WARNING: It is critical for safety and for the

proper function of the sideburner

that the sideburner venturi tube with

air shutter be centered around and

completely cover the gas oriﬁ ce.

3. Insert and start screws with ﬁ ngers and then

tighten using a Phillips screwdriver.

Important: Take caution to not cross-thread

when tightening the screws.

Note: Upon completion, the air shutter must still

ﬁ t around the brass oriﬁ ce.

4. Connect the female connector on the end of the

hot surface ignitor wire to the male connector

coming from inside the grill.

5. Place the burner cap on top of the burner, as

shown in Fig. 17-3.

6. Place the grid so that it rests on the front

and back lips of the sideburner opening (Fig.

17-4).

7. Proceed to the section on AIR SHUTTER

ADJUSTMENT and complete the installation by

adjusting the air shutter. This will also test the

sideburner installation.

Air-shutter oriﬁ ce placement - under shelf

Fig. 17-1

Connecting the ignitor wires

Placing the burner cap

Fig. 17-2

Fig. 17-3

Final look

Fig. 17-4

Screw

Hole

Male

Female

Brass

oriﬁ ce

Air

shutter

Grate

Lid

Cap

Shelf

INSTALL THE SIDEBURNER SHELF (IF EQUIPPED)

Fig. 18-1 Type I Acme thread quick coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁ tting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 18-1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check

the hose for wear (see a.) and check all

connections for leaks. Turn off the unit valves

and open the main cylinder valve, then check

connections with soapy water. Repair any

leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂ ow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected

cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁ ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if

there is visible damage to either the cylinder or valve. If the

hose is cut or shows excessive abrasion or wear, it must

be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with an OPD (Overﬁ ll Prevention Device).

The OPD has been required on all cylinders sold since

October 1,1998, to prevent overﬁ lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the

Speciﬁ cations for Propane Gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 18-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁ ed

by the manufacturer for connection with a cylinder

connecting device identiﬁ ed as Type I by the ANSI Z

21.58-2005/CGA 1.6-2005 (see PARTS LIST for ordering

information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type I

in the standard deﬁ ned in paragraph e. above. This device

is commonly described as an Acme thread quick coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁ tting: Press the hand nut on the regulator

over the Acme thread ﬁ tting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

SECURING THE PROPANE-GAS CYLINDER

1. Lift latch handle to unlock

tray and pull outward.

3. With gas cylinder in place and connected, slide

tray back into cart and lock latch handle by

pushing ﬁ rmly downward.

2. Set propane-gas cylinder into the sleeve of the extended tray with

base inserted into center hole and collar opening to back. Follow

instructions above to connect supply.

Collar

Opening

Fig. 18-2

Fig. 18-3

Fig. 18-5

Fig. 18-4

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

Fig. 19-1 type coupleur rapide de ﬁ l de point culminant d’I

Valve

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁ l de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁ l de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁ ls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁ g. 19-1).

Important: Avant d’employer le gril, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour déceler

les fuites. Arrêtez les valves de gril et ouvrez

la valve principale de cylindre, puis vériﬁ ez

les raccordements avec de l’eau savonneux.

Réparez toutes les fuites avant d’allumer le gril.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le gril et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁ ssuré ou efﬁ loché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁ letées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Des cylindres et les valves de gaz de propane doivent être

maintenus en bon état et doivent être remplacés s’il y a

des dommages évidents au cylindre ou à la valve.

b. Ce gril, une fois utilisé avec un cylindre, devrait être relié à

un gallon de la norme 5 (20lb.) cylindre de gaz de propane

équipé d’un OPD (remplissez au-dessus du niveau le

dispositif d’empêchement). L’OPD a été exigé sur tous les

cylindres vendus depuis octobre 1.1998 pour empêcher le

remplissage excessif.

c. Les dimensions de cylindre devraient être approximativement

12"(30.5cm) de diamètre et 18" (45.7cm) hauts. Des

cylindres doivent être construits et marqués selon les

caractéristiques pour des cylindres de gaz de propane du

département des ETATS-UNIS du transport (D.O.T.) ou

le niveau national du Canada, du CAN/CSA-B339, des

cylindres, des sphères et des tubes pour le transport des

marchandises dangereuses.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂ exible (Fig. 19-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁ és par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁ ée comme de type I par

le 21.58-2005/CGA ANSI Z 1.6 à 2005 (voir liste des pièces

pour les informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁ nie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur rapide de ﬁ l de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR RAPIDE

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁ l

de point culminant sur la valve de cylindre. Tournez l’écrou de

FIXATION DU CYLINDRE DE GAZ DE PROPANE

1. Soulevez la poignée de

verrouillage pour ouvrir

le plateau et pour tirer à

l’extérieur.

3. Avec le cylindre de gaz en place et relié,

glissez le plateau de nouveau dans la poignée

de verrouillage de chariot et de serrure en

poussant fermement en bas.

2. Placez le cylindre de gaz de propane gainent fermement sur

le plateau avec la base insérée dans le trou central et le collier

s’ouvrant au dos. Suivez les instructions de relier ci-dessus

l’approvisionnement.

Fig. 19-2

Fig. 19-3

Fig. 19-5

Fig. 19-4

Ouverture

de Collier

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

IDENTIFICATION OF GRILL CONTROLS

Power burner control locations

Double sideburner control locations

Inner power burner

control knob

Outer power burner

control knob

Fig. 20-2

Left

main burner

control knob

Right

main burner

control knob

Right backburner

control knob

Digital

thermometer

Sideburner

control knob

Center

main burner

control knob

Fig. 20-4

Left

main burner

control knob

Right

main burner

control knob

Backburner

control knob

Digital

thermometer

Sideburner

control knob

E1060s control locations

E660s and E790s control locations

Smoker

drawer burner

control knob

Center right main

burner

control knob

Center left main

burner

control knob

Drip

tray

Drip

trays

Smoker drawer

burner control

knob

Left backburner

control knob

Power hood

control

(if equipped)

Fig. 20-1

Control panel

screw(s)

Control panel

screw(s)

Smoker

drawer

Smoker

drawer

Power hood

control

(if equipped)

Master

switch

Master

switch

Rear sideburner

control knob

Front sideburner

control knob

Fig. 20-3

La page charge ...

Fire Magic E1060S4EAP71 Guide d'installation

Marque: Fire Magic

Modèle: E1060S4EAP71

Catégorie: Barbecues

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Fire Magic E1060S4EAP71 Installation guide

Fire Magic E1060S4EAP71 Guide d'installation

Fire Magic E1060S4EAP71 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents