Philips MCM240/25 Manuel utilisateur

Catégorie
Ensembles audio pour la maison
Taper
Manuel utilisateur
MCM240
Micro Hi-Fi System
User manual
Manuel d'utilisation
Manual del usuario
Benutzerhandücher
Gebruikershandleidingen
Manuale per l'utente
Användarhandböckerna
Brugermanual
Käyttöoppaita
Manual do usuário
 
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM1
3140 115 xxxxx
2
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 3 Amp,
A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 3 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 3 Amp.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
Connect the blue wire to the terminal
marked N or coloured black.
Connect the brown wire to the terminal
marked L or coloured red.
Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio MCM240 Philips
risponde alle prescrizioni dell’art. 2 comma 1
del D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
VAROITUS
Muiden kuin tässä esitettyjen
toimintojen säädön tai asetusten
muutto saattaa altistaa vaaralliselle
säteilylle tai muille vaarallisille
toiminnoille.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM2
3140 115 xxxxx
3
3
)
1
3
4
6
7
8
9
5
!
0
2
^
(
1
!
7
0
8
*
%
@
3
#
$
&
5
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM3
3140 115 xxxxx
4
DK
Advarsel: Usynlig laserstråling ved åbning
når sikkerhedsafbrydere er ude af funktion.
Undgå utsættelse for stråling.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket
sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats,
kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för
laserklass 1.
Observera! Stömbrytaren är sekundärt
kopplad och bryter inte strömmen från
nätet. Den inbyggda nätdelen är därför
ansluten till elnätet så länge stickproppen
sitter i vägguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen
muulla kuin tässä käyttöohjeessa mainitulla
tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei
saa olla alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-
osa on kytkettynä sähköverkkoon aina
silloin, kun pistoke on pistorasiassa.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM4
3140 115 xxxxx
5
English
Français
Por tuguês
EspañolDeutschNederlandsItalianoSvenskaDanskSuomi

Index
English ------------------------------------------------ 6
Français -------------------------------------------- 21
Español --------------------------------------------- 36
Deutsch --------------------------------------------- 51
Nederlands ---------------------------------------- 66
Italiano ---------------------------------------------- 81
Svenska --------------------------------------------- 96
Dansk --------------------------------------------- 111
Suomi --------------------------------------------- 126
Por tuguês ---------------------------------------- 141
E ----------------------------------------- 156
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM5
6
English
Contents
General Information
Environmental information ................................ 7
Supplied accessories ............................................ 7
Safety information ................................................ 7
Preparations
Rear connections .......................................... 8 – 9
Optional connection ........................................... 9
Connecting other equipment to your system
Before using the remote control ...................... 9
Replacing battery (lithium CR2025) into the
remote control ..................................................... 9
Controls
Controls on the system and remote
control .................................................................. 10
Basic Functions
Switching the system on ................................... 11
Switch the system to
Eco Power Standby mode ................................ 11
Power Saving Automatic Standby .................... 11
Adjusting volume and sound ............................ 11
CD/MP3-CD Operation
Loading a disc ...................................................... 12
Basic playback controls ..................................... 12
Playing an MP3 disc ............................................ 13
Finding a passage within a track ...................... 13
Different play modes: SHUFFLE and REPEAT13
Programming track numbers ........................... 13
Reviewing the programme ............................... 14
Erasing the programme ..................................... 14
Radio Reception
Tuning to radio stations .................................... 15
Programming radio stations ............................. 15
Automatic programming
Manual programming
Tuning to preset radio stations ....................... 15
RDS ....................................................................... 15
Setting the RDS clock ....................................... 16
Searching programme type (PTY) .................. 16
Clock/Timer
Setting the clock ................................................. 17
Viewing the clock ............................................... 17
Setting the timer................................................. 17
Activating and deactivating TIMER ................. 17
Activating and deactivating SLEEP .................. 18
Specifications ........................................... 19
Maintenance.............................................. 19
Tr oubleshooting .................................... 20
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM6
English
7
General Information
This product complies with the radio
interference requirements of the European
Community.
Environmental Information
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Supplied accessories
–2 speaker boxes
remote control (with battery)
MW loop antenna
FM wire antenna
stand
screw and plug assembly
Safety Information
Before operating the system, check that the
operating voltage indicated on the typeplate (or
the voltage indication beside the voltage
selector) of your system is identical with the
voltage of your local power supply. If not, please
consult your dealer.
Place the system on a flat, hard and stable
surface.
Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the system. Should this occur, the CD
player would not operate normally. Leave the
power on for about one hour with no disc in the
system until normal playback is possible.
The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM7
8
English
Preparations
Rear connections
The type plate is located at the rear of the
system.
For users in the U.K.: please follow the
instructions on page 2.
A Power
Before connecting the AC power cord to the
wall outlet, ensure that all other connections
have been made.
Warning!
–For optimal performance, use only the
original power cable.
–Never make or change any connections
with the power switched on.
To avoid overheating of the system, a safety
circuit has been built in. Therefore, your
system may switch to Standby mode
automatically under extreme conditions. If
this happens, let the system cool down
before reusing it (not available for all versions).
B Antennas Connection
Connect the supplied MW loop antenna and FM
antenna to the respective terminals. Adjust the
position of the antenna for optimal reception.
MW Antenna
Position the antenna as far as possible from a TV,
VCR or other radiation source.
MW loop antenna
Speaker
(right)
Speaker
(left)
FM wire antenna
AC power cord
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM8
English
9
plastic
protective
sheet
FM Antenna
For better FM stereo reception, connect an
outdoor FM antenna to the FM ANTENNA
terminal.
C Speakers Connection
Front Speakers
Connect the speaker wires to the SPEAKERS
terminals, right speaker to "RIGHT" and left
speaker to "LEFT", colored (marked) wire to "+"
and black (unmarked) wire to "-".
Fully insert the stripped por tion of the speaker
wire into the terminal as shown.
Notes:
–For optimal sound performance, use the
supplied speakers.
Do not connect more than one speaker to any
one pair of +/- speaker terminals.
Do not connect speakers with an impedance
lower than the speakers supplied. Please refer to
the SPECIFICATIONS section of this manual.
Optional connection
The optional equipment and connecting cords are
not supplied. Refer to the operating instructions
of the connected equipment for details.
Connecting other equipment to your
system
Connect the audio left and right OUT terminals
of a TV, VCR, Laser Disc player, DVD player or
CD Recorder to the AUX terminals.
Note:
If you are connecting equipment with a mono
output (a single audio out terminal), connect it to
the AUX left terminal. Alternatively, you can use a
“single to double” cinch cable (the output sound
still remain mono).
Before using the remote control
1
Pull out the plastic protective sheet.
2 Select the source you wish to control by
pressing one of the source select keys on the
remote control (for example CD, TUNER).
3 Then select the desired function (for example
ÉÅ , í , ë).
Replacing battery (lithium
CR2025) into the remote control
1
Pull out the knob A slightly to the left.
2 Pull out the battery compartment B .
3 Replace a new battery and fully insert the
battery compartment back to the original
position.
CAUTION!
Batteries contain chemical substances, so
they should be disposed of properly.
Preparations
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM9
10
English
Controls (illustrations on page 3)
Controls on the system and
remote control
1
STANDBY-ON/ ECO POWER (B)
switches the system on or to Eco Power
standby/normal standby with clock display.
2 Display screen
shows the status of the system.
3 OPEN • CLOSEç
opens/closes the CD door.
4 IR
remote sensor
5 VOLUME (3 / 4 ) (+/-)
adjusts the volume level.
adjusts the hours and minutes for the clock/timer
function.
6 CD Door
7 Mode Selection
ALBUM/ TUNE/ALBUM -/+ (à / á)
for TUNER ........ tunes to a station
for CD/MP3-CD fast searches back and
forward within a track/disc (press
and hold).
for MP3-CD ..... skips to the beginning of a
current/previous/subsequent
album.
9 ............................. stops disc playback or erases a
disc programme.
ÉÅ ................... starts or interrupts playback.
PRESET (¡ / )
for TUNER ........ selects a preset radio station.
for CD/MP3 -CD skips to the beginning of a
current/previous/subsequent
track
8 DBB (Dynamic Bass Boost)
enhances the bass.
9 BAND
selects a waveband.
0 PROGRAM
for CD/MP3-CD programmes tracks and
reviews the programme.
for TUNER ........ programmes tuner stations.
! SOURCE
selects the respective sound source for CD/
TUNER/ AUX.
Notes for remote control:
First select the source you wish to
control by pressing one of the source select
keys on the remote control (for example
CD, TUNER).
Then select the desired function (for
example
ÉÅ
,
í
,
ë
).
@ DISPLAY/CLOCK
sets the clock function.
displays disc information during playback.
# TIMER
activates/ deactivates or sets the timer function.
$ SLEEP
activates/deactivates or selects the sleeper time.
% DSC (Digital Sound Control)
selects sound characteristics: ROCK/ JAZZ/
POP/ CLASSIC.
^ RDS
–for tuner, displays RDS information.
& MUTE
interrupts and resumes sound reproduction.
* REPEAT
repeats a track/disc programme/entire disc.
( SHUFFLE
plays disc tracks in random order.
) n
–connects headphones
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM10
English
11
Basic Functions
Important!
Before you operate the system, complete
the preparation procedures.
Switching the system on
Press STANDBY-ON/ECO POWER (or B
on the remote).
The system will switch to the last selected
source.
Press CD, TUNER or AUX on the remote
control.
The system will switch to the selected source.
Press OPEN•CLOSEç.
The system will switch to the CD source.
Switching the system to Eco
Power Standby mode
Press STANDBY-ON/ECO POWER (or B
on the remote).
The backlight for clock display is dim in
standby.
"ECO PWR" will be displayed, then the display
screen will go blank.
The ECO POWER LED will be lighted.
To view clock time in standby mode, press and
hold STANDBY-ON/ECO POWER (or B
on the remote) for more than 3 seconds or
more.
The system enters the standby mode with
clock display.
The volume level (up to a maximum volume
level of 20), interactive sound settings, last
selected mode (ECO Power Standby or normal
standby), source and tuner presets will be
retained in the player's memory.
Power Saving Automatic Standby
As a power-saving feature, the system
automatically switches to Eco Power/ Standby 15
minutes after a CD has reached the end and no
control is operated.
Adjusting volume and sound
1
Press VOLUME 3 / 4 (+/-) to decrease or
increase the volume.
Display shows the volume level VOL and a
number from MIN1, 2, ...30, 31 MAX.
2 Press DSC repeatedly to select the desired
sound effect: ROCK/ JAZZ/ POP/ CLASSIC.
3 Press DBB to switch bass enhancement on or
off.
Display shows: DBB.
4 Press MUTE on the remote control to
interrupt sound reproduction instantly.
Playback will continue without sound and the
display shows MUTE.
To activate sound reproduction you can:
press MUTE again;
adjust the volume controls;
change source.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM11
12
English
Basic playback controls
To play a disc
Press ÉÅ to start playback.
The current track number and elapsed
playing time of the track are displayed during
disc playback.
To select a different track
Press PRESETí / ë (or í / ë on the
remote) once or repeatedly until the desired
track number appears in the display.
If you have selected a track number shortly after
loading a disc or in the PAUSE position, you will
need to press ÉÅ to start playback.
Te xt display during playback
In CD mode
Press DISPLAY to show the current track
number and remaining playback time.
In MP3-CD mode
Press DISPLAY repeatedly to show the current
album and track numbers followed by ID3
information (if available).
To find a passage within a track
1 Press and hold down on ALBUM/TUNE à /
á (or ALBUM -/+ à /á on the remote).
The disc is played at high speed and low
volume.
2 When you recognize the passage you want,
release ALBUM/TUNE à /á (or ALBUM
-/+ à /á on the remote).
Normal playback continues.
To interrupt playback
Press ÉÅduring playback.
The display freezes and the elapsed playing
time flashes when playback is interrupted.
To resume, press ÉÅ again.
To stop playback
Press 9.
Important!
The lens of the CD player should never be
touched.
Loading a disc
This CD player plays Audio Discs including CD
Recordables, CD-Rewritables and MP3 CD.
CD-ROM, CD-I, CDV, VCD, DVD or computer
CDs, however, are not possible.
1 Press SOURCE on the front panel of the
system to select CD or press CD on the
remote.
2 Press OPEN•CLOSEç to open the CD
compartment.
OPEN is displayed when the compartment
cover slides up.
3 Insert a disc with the printed side facing up.
Press OPEN•CLOSEç again to close the
compartment.
READING is displayed as the CD player
scans the contents of a disc, and then the total
number of tracks and playing time (or the total
number of albums and tracks for MP3 disc) are
shown.
CD/MP3-CD Operation
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM12
English
13
CD/MP3-CD Operation
Notes:
CD play will also stop when;
the CD door is opened.
the disc has reached the end.
you select another source: TUNER or AUX.
you select standby.
the set auto off time arrives.
no button is pressed within 15 minutes in the
CD PAUSE position.
Playing an MP3 disc
1
Load an MP3 disc.
The disc reading time may exceed 10
seconds due to the large number of songs
compiled into one disc.
The total number of albums and tracks (titles)
are shown.
2 Press ALBUM/TUNE à /á (or ALBUM -/
+ à /á on the remote) to select a desired
album.
3 Press PRESETí / ë (or í / ë on the
remote) to select a desired track.
The album number will change accordingly as
you reach the first track of an album by pressing
í or the last track of an album by pressing ë.
4 Press ÉÅ to start playback.
Supported MP3 disc formats:
ISO9660, Joliet, UDF 1.5
Maximum title number: 400 (depending on
filename length)
Maximum album number: 40
Supported sampling frequencies: 32 kHz,
44.1kHz, 48 kHz
Suppor ted Bit-rates: 32~256 (kbps), variable
bitrates
Different play modes: SHUFFLE
and REPEAT
You can select and change the various play
modes before or during playback. The REPEAT
modes can also be combined with PROGRAM.
SHUFFLE .........tracks of the entire disc are
played in random order
SHUFFLE and REPEAT ALL
................................. to repeat the entire disc
continuously in random order
REPEAT ALL ... repeats the entire disc/ program
REPEAT ............ plays the current track
continuously
1 To select your play mode, press SHUFFLE or
REPEAT on the remote control before or
during playback until the display shows the
desired function. (SHUFFLE, REPEAT, REPEAT
ALL)
2 PressÉÅ to start playback if in the STOP
position.
If you have selected SHUFFLE, playback starts
automatically.
3 To return to normal playback, press the
respective SHUFFLE or REPEAT button until
the various SHUFFLE / REPEAT modes are no
longer displayed.
You can also press 9 to cancel your play mode.
Programming track numbers
Program in the STOP position to select and
store your disc tracks in the desired sequence. If
you like, store any track more than once. Up to
40 tracks can be stored in the memory.
1 Press PROGRAM to enter the programming
mode.
A track number is shown and
PROGRAM
flashes.
2 Use PRESETí / ë (or í / ë on the
remote) to select your desired track number.
For MP3 CD, press ALBUM/TUNE à /á
(or ALBUM -/+ à /á on the remote) to
select your desired album.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM13
14
English
3 Press PROGRAM to confirm the track number
to be stored.
PROG X is shown briefly, followed by the
number of the track (for MP3-CD, the album
and title numbers of the track) you just stored.
X denotes the next program number to be
stored
4 Repeat steps 2-3 to select and store all desired
tracks.
FULL is displayed if you attempt to program
more than 40 tracks.
5 To star t playback of your disc program, press
STOP 9 followed by ÉÅ or press ÉÅ
directly.
Reviewing the program
In STOP mode, press and hold PROGRAM
until the display shows all your stored track
number in sequence.
Erasing the program
You can erase the program by:
pressing STOP 9 once in the STOP mode;
pressing STOP 9 twice during playback;
opening the CD compartment;
PROGRAM disappears, CLEAR scrolls and
then disappears from the display.
CD/MP3-CD Operation
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM14
English
15
Radio Reception
Tuning to radio stations
1
Press SOURCE on the front panel of the
system or TUNER on the remote to select
TUNER.
TUNER is displayed briefly.
2 Press BAND on the front panel of the system
once or more to select your waveband (FM/
MW).
3 Press and hold ALBUM/TUNE à /á (or
ALBUM -/+ à /á on the remote).
The radio automatically tunes to a station
with sufficient reception. Display indication
during automatic tuning: SEARCH.
4 Repeat step 3 if necessary until you find the
desired station.
To tune to a weak station, press ALBUM/
TUNE à /á (or ALBUM -/+ à /á on
the remote) briefly and repeatedly until you
have found optimal reception.
Programming radio stations
You can store up to a total of 40 radio stations
in the memory for each band.
Automatic programming
Automatic programming will start with a chosen
preset number. From this preset number
upwards, former programmed radio stations will
be overridden.
1 Press PRESETí / ë (or í / ë on the
remote) to select the preset number where
programming should start.
Note:
If no preset number is selected, default is preset
(1) and all your presets will be overridden.
2 Press PROGRAM for more than 2 seconds to
activate programming.
AUTO is displayed and available stations are
programmed in order of waveband reception
strength: FM followed by MW. The last preset
automatically stored will then be played.
Manual programming
1 Tune to your desired station (see “Tuning to
radio stations”).
2 Press PROGRAM to activate programming.
3 Press PRESETí / ë (or í / ë on the
remote) to allocate a number from 1 to 40 to
this station.
4 Press PROGRAM again to confirm the setting.
The preset number and the frequency of the
preset station are shown.
5 Repeat the above four steps to store other
stations.
You can override a preset station by storing
another frequency in its place.
Tuning to preset radio stations
Press PRESETí / ë (or í / ë on the
remote) until the desired preset station is
displayed.
RDS
Radio Data System is a service that allows
FM stations to show additional information. If
you are receiving a RDS station,
and the
station name are displayed.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM15
16
English
Radio Reception
Scrolling through different RDS
information
Press RDS briefly and repeatedly to scroll
through the following information (if available):
Station name
Programme type such as NEWS, SPORT,
POP M ...
Radio text messages
Frequency
Note:
If you press RDS and the RDS signal is not
available NO RDS is displayed.
Setting the RDS clock
Some RDS radio station may be transmitting a
real clock time at an interval of every minute. It
is possible to set the clock by using a time signal
which is broadcast together with the RDS signal.
1 Tuned to a RDS station from FM band (refer to
“Tuning to radio stations”).
2 Press and hold DISPLAY until "SET CLOCK" is
displayed.
3 Press RDS.
"SEARCH RDS TIME" appears.
When RDS time is read, the current time will
be stored.
If the RDS station does not transmit RDS
time within 30 seconds, "NO RDS TIME"
appears.
Note:
Some RDS radio station may be transmitting a
real time clock at a minute interval. The accuracy
of the transmitted time depends on the
transmitting RDS radio station.
Searching programme type
(PTY)
PTY helps you find a desired programme type.
To enable PTY, first programme RDS stations
into the tuner memory (see Programming radio
stations)
1 While receiving an RDS station, press RDS
briefly until the programme type is displayed.
2 Press PRESETí / ë (or í / ë on the
remote) until the desired programme type is
displayed.
3 Press and hold down on ALBUM/TUNE à /
á (or ALBUM -/+ à /á on the remote) to
start searching.
The radio tunes to a RDS station
broadcasting this programme type. If the
programme type is not available TYPE NOT
FOUND is displayed.
RDS Programme types
NO TYPE .......... No RDS programme type
NEWS .................... News services
AFFAIRS .......... Politics and current affairs
INFO .................... Special information programmes
SPORT ................ Sports
EDUCATE .......... Education and advanced training
DRAMA ................ Radio plays and literature
CULTURE .......... Culture, religion and society
SCIENCE .......... Science
VARIED ............. Entertainment programmes
POP M ................. Pop music
ROCK M .............. Rock music
MOR M ................. Light music
LIGHT M .......... Light classical music
CLASSICS ...... Classical music
OTHER M .......... Special music programmes
WEATHER .......... Weather
FINANCE .......... Finance
CHILDREN ...... Children’s programmes
SOCIAL ............. Social Affairs
RELIGION ...... Religion
PHONE IN ....... Phone In
TRAVEL ............. Travel
LEISURE .......... Leisure
JAZZ .................... Jazz Music
COUNTRY .......... Country Music
NATION M ....... National Music
OLDIES ............. Oldies Music
FOLK M .............. Folk Music
DOCUMENT ...... Documentary
TEST .................... Alarm Test
ALARM ................ Alarm
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM16
English
17
Clock/Timer
Setting the clock
1
In standby mode or system on, press and hold
DISPLAY/CLOCK on the remote control for
more than 3 seconds.
SET CLOCK scrolls on the display.
The clock digits for the hours flash.
2 Press VOLUME (3 / 4) (+/-) to set the hours.
3 Press DISPLAY/CLOCK again.
The clock digits for the minutes flash.
4 Press VOLUME (3 / 4) (+/-) to set the
minutes.
5 Press DISPLAY/CLOCK to confirm the time.
Note:
The backlight for clock display is dim in standby.
Viewing the clock
Press DISPLAY/CLOCK.
The clock time is displayed.
Note:
There is no time display during disc playback.
Setting the timer
The system can be used as an alarm clock,
whereby the CD, TUNER is switched on at a set
time. The clock time needs to be set first before
the timer can be used.
During setting, if no button is pressed within 30
seconds, the system will exit timer setting mode
automatically.
1 In standby mode or system on, press and hold
TIMER on the remote control for more than 3
seconds.
Display sequence scrolls SET TIMER and
SELECT SOURCE.
Display sequence shows CD, TUNER and
flashes.
2 Press VOLUME (3 / 4) (+/-) to select the
sound source.
3 Press TIMER to confirm your desired mode.
The clock digits for the hours flash.
4 Press VOLUME (3 / 4) (+/-) to set the hours.
5 Press TIMER again.
The clock digits for the minutes flash.
6 Press VOLUME (3 / 4) (+/-) to set the
minutes.
7 Press TIMER to confirm the time.
Display sequence shows VOL12.
8 Press VOLUME (3 / 4) (+/-) to set the timer
volume level.
9 Press TIMER to confirm.
The timer is now set and activated.
Activating and deactivating
TIMER
Press TIMER on the remote to turn off the
timer or turn on to the last setting again.
If activated, the timer information will display
for a few seconds, then the system resumes to
the last active source or stays in standby mode.
If deactivated, OFF appears.
Note:
The system will exit timer setting mode if no
button is pressed within 30 seconds.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM17
18
English
Clock/Timer
Activating and deactivating
SLEEP
The sleep timer enables the
system to switch off by itself
after a set period of time.
Press SLEEP on the remote
control once or more.
Display shows SLEEP and one of the sleep
time options in sequence: 90, 60, 45, 30, 15,
OFF, 90... if you have selected a time. Once
SLEEP is activated, SLEEP is display.
To deactivate, press SLEEP on the remote
control repeatedly until OFF is shown, or press
STANDBY-ON/ ECO POWER (or B on
the remote).
OFF is displayed.
pg001-020_MCM240_22_Eng 2005.5.10, 3:08 PM18
English
19
Cleaning the Cabinet
Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the centre
out.
Do not use solvents such as
benzene, thinner, commercially
available cleaners, or antistatic spray intended for
analogue records.
Cleaning the disc lens
After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
cleaner. Follow the instructions supplied with
cleaner.
Maintenance
Specifications
AMPLIFIER
Output power .......................................... 2 x 5 W RMS
............................................................ 10 W + 10 W MPO
Signal-to-noise ratio ....................................... 62 dBA
Frequency response ......... 63 – 16000 Hz, ± 3 dB
Input sensitivity AUX ....................... 0.5 V (max. 2 V)
Impedance loudspeakers ......................................... 4
Impedance headphones .................... 32 -1000
......................................................................................... <0.5W
CD PLAYER
Frequency range .................................. 30 – 16000 Hz
Signal-to-noise ratio ............................................ 75 dBA
TUNER
FM wave range ................................... 87.5 – 108 MHz
MW wave range ................................ 531 – 1602 kHz
Sensitivity at 75
– mono, 26 dB signal-to-noise ratio ............ 2.8 µV
– stereo, 46 dB signal-to-noise ratio ........ 61.4 µV
Selectivity ................................................................. 28 dB
Total harmonic distortion ..................................... 5%
Frequency response ..... 63 – 12500 Hz (± 3 dB)
Signal-to-noise-ratio ...................................... 50 dBA
SPEAKERS
Bass reflex system
Dimensions (w x h x d) .... 166 x 245 x 90 (mm)
GENERAL INFORMATION
AC Power ..................................... 220 – 240 V / 50 Hz
Dimensions (w x h x d) .... 250 x 245 x 96 (mm)
Weight(with/without speakers) ........... 4.4 / 2.5 kg
Standby power consumption ............................ <7 W
Eco power standby ................................................. <1 W
Specifications and external appearance are
subject to change without notice.
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM19
20
English
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If you
are unable to remedy a problem by following these hints, consult your dealer or Philips for
help.
NO DISC” is displayed.
Radio reception is poor.
The system does not react when buttons
are pressed.
Sound cannot be heard or is of poor
quality.
The left and right sound outputs are
reversed.
The remote control does not function
properly.
The timer is not working.
The Clock/Timer setting is erased.
Insert a disc.
Check if the disc is inserted upside down.
Wait until the moisture condensation at the lens
has cleared.
Replace or clean the disc, see “Maintenance”.
Use a finalised CD-RW or a correct MP3-CD
format disc.
If the signal is too weak, adjust the antenna or
connect an external antenna for better
reception.
Increase the distance between the Micro HiFi
System and your TV or VCR.
Remove and reconnect the AC power plug and
switch on the system again.
Adjust the volume.
Disconnect the headphones.
Check that the speakers are connected correctly.
Check if the stripped speaker wire is clamped.
Make sure the MP3-CD was recorded within
32~256 kbps bit rate with sampling frequencies
at 48 kHz, 44.1 kHz or 32 kHz.
Check the speaker connections and location.
Select the source (CD or TUNER, for example)
before pressing the function button (ÉÅ,í,
ë).
Reduce the distance between the remote
control and the system.
Insert the battery with its polarities
(+/– signs) aligned as indicated.
Replace the battery.
Point the remote control directly toward
IR sensor on the front of the system.
Set the clock correctly.
Press TIMER to switch on the timer.
Power has been interrupted or the power cord
has been disconnected. Reset the clock/timer.
Problem
Solution
pg001-020_MCM240_22_Eng 2005.5.9, 5:57 PM20
1 / 1

Philips MCM240/25 Manuel utilisateur

Catégorie
Ensembles audio pour la maison
Taper
Manuel utilisateur

dans d''autres langues