HoMedics HTD8216C Mode d'emploi

Catégorie
Thermomètres corporels numériques
Taper
Mode d'emploi
2 YEAR GUARANTEE
Model: HTD8216C
INFRARED
BODY
THERMOMETER
TE-300-EU 1
GB | 2
GB | 3
FOREWORD
The Infrared Body Thermometer operating Instructions intend to provide the necessary
information for proper operation of the thermometer model.
Only body mode was reviewed and certified by notified body. General knowledge
of Infrared thermometer and an understanding of the features and functions of the
thermometer model are prerequisites for proper use. The Infrared Body Thermometer
is a medical device, and can be used repeatedly for the product’s recommended
lifetime of 5 years.
Please read the manual first before using it, if not fully understand the usages, please
stop using the thermometer.
Do not operate the thermometer without completely reading and understanding these
instructions.
Notice
Purchase or possession of this device does not carry any express or implied license to
use with replacement parts which would, alone or in combination with this device, fall
within the scope of one of the relating patents.
For further information contact:
FKA Brands Ltd, Somerhill Business Park, Five Oak Green Road,
Tonbridge, Kent TN11 0GP.
Customer Service: [email protected]
Share Info Consultant Service LLC Repräsentanbüro
Heerdter Lohweg 83, 40549 Düsseldorf
GB | 2
GB | 3
SAFETY INFORMATION
This device may only be used for the purposes described in these instructions. The
manufacturer cannot be held liable for damage caused by incorrect application.
The Infrared Body Thermometer is designed to minimize the possibility of hazards from
errors in the software program by following sound and light engineering
design processes, Risk Analysis and Software Validation.
WARNING
Warnings are identified by the WARNING symbol shown above.
The Infrared Body Thermometer is to be operated by consumers in the home setting
and primary care setting as screening tool. This manual, accessories, Directions for
Use, all precautionary information, and specifications should be read before use.
This product is designed to measure human body temperature on the forehead and
ear. Do not use it for any other purpose.
This product is intended for use in the home setting and primary care setting as
screening tool.
Do not use the thermometer if it malfunctions or has been damaged in any matter.
When the ambient temperature of the thermometer changes too much, such as
moving the Thermometer from one place of lower temperature to another place of
higher temperature, allow the thermometer to remain in a room for 30 minutes where
the temperature is between 15°C to 35°C (59°F- 95°F).
Remove primary batteries if equipment is not likely to be used for long time.
This product is not waterproof, do not immerse in water or other liquid; If cleaning
and disinfecting, please follow the “Care and Storage” section requirements.
Do not touch the sensor of infrared detection with your fingers.
Avoid using the thermometer to take a body temperature reading while using a cold
compress or other measure to reduce fever.
If measuring human temperature, please select “body” mode or“ear” mode.
This product must be operated in a stable environment. If the ambient environment
is unstable, please check whether there is fog on the sensor and remove this before
using in accordance with the “Care and Storage” section.
1 2 3
5
6
7 8 9
4
1 2
3
4
5
GB | 4
GB | 5
Do not near strong electrostatic field or strong magnetic fields, thus avoiding the
impact on the accuracy of the measurement data.
Do not mix the old and new batteries to avoid damage to the product.
It may aect the accuracy of measurements when the forehead is covered by hair,
perspiration, cap or scarf.
The measuring result of this product is only for your reference. If you have any doubt,
please measure the temperature in other methods. Also the ear wax will lower
down the temperature. So please be sure use correct way in case of accuracy of
measurements.
Some people are not suitable to use ear mode properly for oily ears or for other
reasons.
The device should be kept out of the reach of children/pets. When not in use, store
the device in a dry room and protect it against extreme moisture, heat, lint, dust and
direct sunlight. Never place any heavy objects on the thermometer body.
Do not throw batteries into fire.
Only use recommended batteries. Do not use rechargeable batteries.
This thermometer does not replace a hospital diagnosis.
Do not drop, disassemble or modify the device.
Do not use this device if you think it is damaged or notice anything unusual.
This device comprises sensitive components and must be treated with caution.
Observe the storage and operating conditions described in the ‘Technical
Specifications’ section.
Not servicing/maintenance while the thermometer is in use.
When using, do not touch battery and the patient simultaneously.
Do not use the device if it is damaged/ degraded/loosened in any way. The continuous
use of a damaged unit may cause injury, improper results, or serious danger.
Based on the current science and technology, other potential allergic reactions are
unknown.
This equipment needs to be installed and put into service in accordance with the
information provided in the ACCOMPANYING DOCUMENTS.
figure 1
1 2 3
5
6
7 8 9
4
1 2
3
4
5
GB | 4
GB | 5
OVERVIEW
Intended Use
The HoMedics Infrared Body Thermometer is designed to be used for intermittent
measurement and monitoring of human body temperature by consumers in the home
setting and primary care setting as screening tool.
Description of Infrared Body Thermometer
Device principle and introduction
The Infrared Body Thermometer is a hand-held, reusable, battery operated device,
which can measure human body temperature on forehead, the skin temperature on
one’s forehead.
The operation principle is based on Infrared Sensor technology. The IR sensor can
output dierent signal when measuring dierent object temperature or in dierent
ambient temperature, and the ASIC can turn the signal from IR Sensor to a digital
value and display it on the LCD.
Description on Controls, Indicators, and Symbols
1. Passive infrared probe
2. Cap
3. Start button
4. Liquid crystal display
(LCD)
5. Battery cover (MODE
button is behind the
battery cover)
1. Forehead mode
2. Ear mode
3. Surface mode
4. Measurement unit
5. Data indicator
6. Low Battery indicator
7. Indicator of
measurement result
8. Volume on/o indicator
9. Memory indicator
figure 1 figure 2
GB | 6
GB | 7
THERMOMETER APPLICATIONS
Thermometer
Model Number Thermometer Style Adult Pediatric
Ear Forehead Ear Forehead
Model: HTD8216C
TE-300-EU 1 Infrared Body Thermometer ü ü ü ü
EQUIPMENT SYMBOLS
Warning Restriction of Hazardous Substances
Non-sterile packaging Batch code
Consult instructions for use Compliance with WEEE Standard
Operating Temperature DO NOT THROW AWAY
Intended for multiple use
Operating Humidity Operating atmospheric pressure
This device compiles with Part 15
of FCC (Federal Communications
Commission) Rules.
Indicates this device is in compliance
with MDD 93/42/EEC. 0598 is the
Notified Body Number
Manufacturer Authorized Representative in the
European community
Recyclable Serial number
Type BF (Body Floating)
IP22: The first number 2: Protected against solid foreign objects of Ф 12.5 mm and
greater. The second number: Protected against vertically falling water drops when
enclosure titled up to 15º.
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
35
1cm-5cm
1cm-5cm
GB | 6
GB | 7
TECHNICAL SPECIFICATIONS
Measurement unit °C/°F
Operating mode Adjusted mode (Body mode)
Direct mode (surface mode)
Measuring site Forehead / Ear
Reference Body Site Axillary
Rated output range 35.0-42.0°C :±0.2°C / 95.0-107.6°F:±0.4°F
Output range Body mode: 34.0-42.9°C / 93.2-109.2°F
Surface mode: 0°C - 100.0°C / 32°F -212°F
Laboratory Accuracy Body mode:
34.0 - 34.9°C: ± 0.3°C / 93.2 - 94.8°F: ± 0.5°F
35.0 - 42.0°C: ± 0.2°C / 95.0 - 107.6°F: ± 0.4°F
42.1 - 42.9°C: ± 0.3°C / 107.8 - 109.2°F: ± 0.5°F
Surface mode:
± 2°C / ± 3.6°F
Display Resolution 0.1°C/0.1°F
Three-colour Backlight
(Colour Alarm) 34 - 37.3°C / 93.2 - 99.1°F: Green (Normal Temperature)
37.4 - 38.0°C (Alarm point) / 99.3 - 100.4°F: Yellow (Slight Fever)
38.1 - 42.9°C / 100.6 - 109.2°F: Red (High Fever)
Note: Colour Alarm is only for Body mode, Surface mode is always with
Green backlight.
Auto Power O Time ≤35s
Measuring Time ≤ 5s (under ear mode)
≤2S(under Forehead mode)
3-10s (under Forehead scan mode)
Memories 1
GB | 8
GB | 9
Power Supply Requirements
Batteries 2 x 1.5V (AAA) Alkaline battery (IEC Type LR03)
Environmental
Operating Condition Operating Temperature:
15 - 35°C (59 - 95°F) Relative Humidity:
≤ 85% Atmospheric pressure:
70-106Kpa
Transport and Storage
Condition Storage Temperature:
-20 - 55°C (-4 - 131°F) Relative Humidity:
≤ 93% Atmospheric pressure:
70-106Kpa
Dimension and Weighting
Weight (without batteries) 66g
Size L:154mm X W:34mm X H:52mm
Compliance
Item Compliant with
Equipment classification Safety Standards:
EN 60601-1: 2006+A1:2013, EN 60601-1-2: 2015
Type of protection Internally powered equipment (on battery power)
Front panel and case labelling EN ISO 15223-1:2016
Temperature EN ISO80601-2-56:2012
Home healthcare environment EN 60601-1-11:2015
Accessory name number
AAA battery 2
User manual 1
GB | 8
GB | 9
Calculated values of the indicators according to ISO80601-2-56-2012
Ear mode:
Group A1 Group A2 Group B Group C
Bias 0.000 -0.097 -0.046 -0.060
Standard deviation 0.175 0.154 0.116 0.125
Limits of agreement 0.349 0.308 0.233 0.249
Clinical repeatability (for all groups) 0.057
Forehead mode:
Group A1 Group A2 Group B Group C
Bias -0.060 -0.083 -0.032 0.000
Standard deviation 0.170 0.144 0.139 0.120
Limits of agreement 0.340 0.288 0.278 0.239
Clinical repeatability (for all groups) 0.108
Forehead scan mode:
Group A1 Group A2 Group B Group C
Bias -0.015 -0.063 -0.068 -0.090
Standard deviation 0.173 0.167 0.135 0.125
Limits of agreement 0.345 0.334 0.269 0.250
Clinical repeatability (for all groups) 0.064
Safety classification of ME EQUIPMENT
Protection against electric shock Internally powered ME equipment
Degree of protection Type BF - applied part (the probe)
Protection against harmful ingress of water
or particulate matter IP22
Mode of operation Continuous operation
Note: Not intended to be sterilized. Not for use in an OXYGEN RICH ENVIRONMENT.
GB | 10
GB | 11
OPERATION
Battery installation
Caution: The Infrared Body Thermometer does not operate with dead batteries or external
power sources. Install new batteries.
1. Slide the battery door downward, toward the bottom of the Infrared Body
Thermometer, and remove the battery access door;
2. Insert two pieces AAA size batteries according to the “+” and “-”;
3. Close the battery cover.
4. The product will not work without batteries installed.
5. Please obey the local laws and regulations to dispose of used batteries properly in
order to avoid environmental pollution.
6. If the thermometer will not be used regularly, remove the battery to prevent
possible damage due to chemical leakage.
7. Before using, check the appearance of the product for abnormalities, to ensure
that the product has not been dropped or sustained any external damage that
could aect its operation. If the product is damaged, do not use.
How to operate
Forehead mode: Put on the probe cap and keep the thermometer aligned with
the middle of the forehead to measure body temperature (between or above the
eyebrows). Holding the product vertically, press the Start button - the temperature
display will immediately appear.
Forehead scan mode: Put on the probe cap, keep the thermometer close to the
forehead and vertical, press and hold the Start button and move the thermometer
from left to right or from right to left for approximately 3-10 seconds. The maximum
temperature will be displayed on the screen.
Please keep the forehead free of hair, perspiration, cap, scarf and etc during forehead
temperature measurement.
Ear mode: Remove the cap and insert ear thermometer probe slightly into the ear
canal, then press the START button , measurement will be finished within 5 seconds.
Please keep the ear canal and probe surface clean when taking ear temperature
measurement.
You should remain in the test environment for at least 5 minutes, and measure after
the ambient temperature is in accordance with the environment.
GB | 10
GB | 11
If using a cold compress or other physical cooling methods, the forehead temperature
will be lower.
The ambient temperature around the test person should be stable, should keep away
from the larger flow fan, air-conditioning vents and so on.
When people moving from one place of lower temperature to another place of higher
temperature, should at least remain in the test environment more than 30 minutes, to
be consistent with the ambient temperature after the re-measurement.
You cannot use the thermometer in place where the sun is strong.
It is recommended that you test at least 3 times and select the result that appears
most often.
When measuring body temperature, please select “ear “ mode or “forehead” mode; for
measurement of other objects, liquid ,food temperature, please select surface mode.
If for some reason the forehead temperature is low, try to take a measurement behind
the ear or select ear mode to measure.
GB | 12
GB | 13
START MEASURING
Ear temperature measurement
1. Turn on the thermometer by pressing the Start button. The thermometer will
perform self-test with all segments displayed for 2 seconds. See figure 3.
2. After full display over, you will hear “beep beep beep”, which means that the
self-test is complete. The last measured temperature will be displayed. If no data
is saved to memory, the display will indicate “----”. See figure 4.
3. When initialisation is complete, the memory symbol disappears and the unit
symbol starts flashing, which means the measurement can be started. See figure
5.
4. If the person being measured is more than one years old, please pull the ear up
and back gently. If less than one year old, pull ear back gently.
5. Insert the thermometer probe slowly into the ear canal and press the START
button. The device will start measuring with a short “beep” once at the start,
then 2 - 5 seconds later. Finally 5 short “beeps” means measurement has been
completed, and the target value of the measured temperature will display on the
LCD. The LCD backlit colour will change to red, yellow or green. Green means the
Normal Temperature and ready for measurement . Yellow means Slight Fever.
Red indicates High Fever. Please kindly note that both yellow and red colour are
a warning.
Note: Colour Alarm is only for Body mode, Surface mode has a Green backlight.
figure 3 figure 4 figure 5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
GB | 12
GB | 13
1. Turn on the thermometer by pressing the Start button. The thermometer will
perform self-test with all segments displayed for 2 seconds. See figure 6.
2. After full display over, you will hear “beep beep beep”, which means that the
self-test is complete. The last measured temperature will be displayed. If no data
is saved to memory, the display will indicate “----”. See figure 7.
3. Please note, if the screen shows this symbol instead of , remove the battery
cover and press the MODE button to switch to forehead mode. See figure 8.
4. After initialisation, the memory symbol “M” will disappear and the unit symbol
°C (or symbol °F) will start flashing which means the device is ready to take a
temperature measurement.
5. Temperature scan method: keep the thermometer vertical and close to the
forehead. Press the Start button. The device will start measuring with a short
“beep” once at the start, then 3 - 10 seconds later. Finally a long “beep” or 5
short “beeps” means measurement has been completed, and the target value of
the measured temperature (maximum) will display on the LCD. The LCD backlit
colour will change to red, yellow or green. Green means the Normal Temperature
and ready for measurement . Yellow means Slight Fever. Red indicates High Fever.
Please kindly note that both yellow and red colour are a warning.
Mode conversion
The product will switch to ear mode if the cap is removed. When the cap is replaced,
forehead mode and surface mode can be switched between using the MODE button. ”ear
“ and “forehead” mode is used for measuring human body temperature, the “surface “
mode is used to measure the surface temperature. (The factory default is “body” mode).
figure 6 figure 7 figure 8
1 2 3
5
6
7 8 9
4
1 2
3
4
5
Forehead temperature measurement
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
1 2 3
5
6
7 8 9
4
1 2
3
4
5
GB | 14
GB | 15
TROUBLESHOOTING
Message Situation Source or Solution
Temperature taken in is higher than typical human
temperature.
Body mode: detected target temperature
higher than 42.9°C
Surface mode : detected target temperature
higher than 100°C
Temperature taken in is lower than typical human
temperature.
Body mode: detected target temperature
lower than 34.0°C
Surface mode : detected target temperature
lower than 0°C
Operating temperature exceeds the range of
specified temperature. Environment temperature higher than 35°C or
lower than 15°C
Wrong function indicated System failure found when system
auto-checks, the screen flickers, and device
automatically turns o.
Battery capacity is too low.
Taking temperature is not allowed. Install a new battery
Ambient temperature is unstable Wait until the ambient temperature is stable.
Please allow device to acclimatise for at least
30 minutes before using it.
Blank screen 1. Press ON button again.
2. Check the battery polarity.
3. Replace with a new battery.
The internal time from the first
measurement to next measurement is less than 5
seconds under ear mode.
Please wait 5 seconds before taking next
measurement.
The measurement result is unvailable, because scan
is too fast under forehead scan mode, or position of
the device is not correct under ear mode.
1. Slow down the scan speed under
forehead scan mode.
2. Put the probe in the right position of ear
canal under ear mode.
Activate mode switch when taking a
measurement. Check if the cap is loose. Please make sure
the cap is loose if you take a measurement
from the forehead.
GB | 14
GB | 15
REPLACING THE BATTERY
1. Open and release battery cover following indicator on the surface of battery cover.
Before changing the battery be sure the thermometer is already turned o.
2. Press the battery holder lock to release the batteries and replace with 2 new type
AAA batteries. Make sure to align properly as indicated inside the battery cover.
3. Slide the battery cover back in until it snaps in place.
Do not dispose of used batteries in household waste. Take them to special local
collection sites.
4. If the thermometer appears frozen after changing the batteries, remove batteries,
wait 30 seconds and replace batteries again.
WARNING
Do not recharge, disassemble or dispose of in fire.
CLEANING, CARE AND STORAGE
The lens is very delicate.
It is very important to protect the lens from dirt and damage.
The Infrared probe is very delicate. Do not touch or use tools on it. It must be carefully
protected otherwise it will aect the accuracy of the measure.
Use an alcohol cloth or 70%~75% alcohol wet cloth to clean the thermometer shell,
surface of the device and LCD. When the thermometer probe is dirty or used by
dierent people, please use alcohol swab or cotton swab moistened with 70%~75%
alcohol to clean and disinfect the probe’s surface of thermometer gently. Do not use
solvents or immerse the device into water or other liquids.
Always keep the thermometer within the storage temperature range (- 20°C to 55°C
or – 4°F to 131°F) and humidity range (≤93% non-condensing).
The device requires at least 30 minutes to warm up from the minimum storage
temperature between uses before it is ready for intended use.
The device requires at least 30 minutes to cool down from the maximum storage
temperature between uses before it is ready for intended use.
It is recommended to store the thermometer in a dry location free from dust. Do
not expose the thermometer to direct sunlight, high temperature/ humidity or any
extreme environment, otherwise the function will be reduced.
GB | 16
GB | 17
When the ambient temperature of the thermometer changes too much, such as
moving the thermometer from one place of lower temperature to another place of
higher temperature, allow the thermometer to remain in a room for 30 minutes where
the temperature is between 15°C to 35°C.
DISPOSAL
Used batteries should not be disposed of in the household rubbish. Used Batteries
should be deposited at a collection point.
At the end of its life, the appliance should not be disposed of in household rubbish.
Enquire about the options for environment-friendly and appropriate disposal. Take
local regulations into account.
WARRANTY
Our company warrants Infrared Body Thermometer at the time of its original purchase
and for the subsequence time period of 2 years.
The warranty does not cover the followings:
The device series number label is torn o or cannot be recognized.
Damage to the device resulting from misconnection with other devices.
Damage to the device resulting from accidents.
Changes performed by users without the prior written authorization of the company.
Batteries and packaging are not covered under warranty
When asked to provide warranty service, you must have a purchase date and purchase
stamp dealers (including dealers name and address) of the warranty card. Be sure to
ask the dealer to purchase this product signature on the warranty card. When asked to
provide warranty service, please put the product to get our distribution points for repair.
Products outside the warranty expires, will be charged accordingly.
Note:
1. If you have any problems with this device, such as setting up, maintaining or
using, please contact with HoMedics Service Centre. Don’t open or repair the
device by yourself.
2. Please report to HoMedics if any unexpected operation or events occur.
GB | 16
GB | 17
3. The thermometer is initially calibrated at the time of manufacture. If this
thermometer is used according to the user instructions, periodic re-adjustment
is not required. If at any time you question the accuracy of temperature
measurements, please contact us.
4. The patient is an intended operator. The patient can measure and change battery.
Under normal circumstances and maintain the device and its accessories
according to the user manual.
EMC DECLARATION
1. This equipment needs to be installed and put into service in accordance with
the information provided in the ACCOMPANYING DOCUMENTS; This product needs
special precautions regarding EMC and needs to be installed and put into service
according to the EMC information provided, and this unit can be aected by
portable and mobile RF communications equipment.
2. * Caution: Do not use a mobile phone or other devices that emit electromagnetic
fields, near the unit. This may result in incorrect operation of the unit.
3. *Caution: This unit has been thoroughly tested and inspected to assure proper
performance and operation!
4. * Caution: this machine should not be used adjacent to or stacked with other
equipment and that if adjacent or stacked use is necessary, this machine should
be observed to verify normal operation in the configuration in which it will be
used.
5. * The infrared body thermometer is suitable for hospitals except for near active
HF SURGICAL EQUIPMENT and the RF shielded room of an ME SYSTEM for magnetic
resonance imaging, where the intensity of EM DISTURBANCES is high.
6. * Performance of the infrared body thermometer such as measure accuracy,
information display would be lost or degraded due to EM DISTURBANCES.
7. * Caution: the EMISSIIONS characteristics of this equipment make it suitable for
use in hospitals and a residential environment (CISPR 11 Class B)
GB | 19
Guidance and manufacturer’s declaration-electromagnetic emissions
The Infrared Body Thermometer is intended for use in the electromagnetic
environment specified below. The customer or the user of the Thermometer should
assure that it is used in such an environment.
Emissions test Compliance
RF emissions CISPR 11 Group 1
RF emissions CISPR 11 Class B
Harmonic emissions
IEC 61000-3-2 Not applicable
Voltage fluctuations
Flicker emissions
IEC 61000-3-3
Not applicable
GB | 18
GB | 19
Guidance and manufacturer’s declaration-electromagnetic immunity
The Thermometer is intended for use in the electromagnetic environment specified below. The
customer or the user of the Thermometer should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level
Electrostatic discharge (ESD)
IEC 61000-4-2 ±8kV contact
±2, ±4, ±8, ±15 kV air ±8kV contact
±2, ±4, ±8, ±15, kV air
Electrical fast transient/burst
IEC 61000-4-4
The input a.c. power ports: ±2 KV
The input d.c. power ports: ±2 KV
Signal input/output ports: ±1 KV Not applicable
Surge IEC 61000-4-5 Input power ports: +0.5, +1.0 KV
Signal input/output:+2.0 KV Not applicable
Voltage dips, short interruptions
and voltage variations on power
supply input lines
IEC 61000-4-11
0.5 cycles for > 95% (sync angle
(degrees):0, 45, 90, 135, 180,225,
270, 315)
1 cycles for >95% UT (sync
angle
(degrees):0)
25 (50Hz)/30 (60Hz) cycles for
30% U T (sync angle
(degrees):0)
Not applicable
Voltage interruption
IEC 61000-4-11
250 (50Hz)/300 (60Hz) cycles
for >95% UT (sync angle
(degrees):0)
Power frequency (50/60 Hz)
magnetic field IEC 61000-4-8 30 A/m 30 A/m
NOTE UT is the a.c. mains voltage prior to application of the test level.
GB | 18
Guidance and manufacturer’s declaration-electromagnetic immunity
The Thermometer is intended for use in the electromagnetic environment specified below. The
customer or the user of the Thermometer should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3Vrms
150kHz to 80 MHz
Professional healthcare
environment: 3 V/m
Home healthcare environment
10 V/m 80MHz to 2.5 GHz
Not applicable
Professional healthcare
environment: 3 V/m
Home healthcare environment
10 V/m 80MHz - 2700 MHz
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and
reflection from structures, objects and people.
a. Field strengths from fixed transmitters, such as base stations from radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast can not be predicted theoretic call with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which the Thermometer is used exceeds the
applicable RF compliance level above, the Thermometer should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating the Thermometer.
b. Over the frequency range 150kHz to 80MHz, field strengths should be less than 3 V/m.
GB | 20
GB | 21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180

HoMedics HTD8216C Mode d'emploi

Catégorie
Thermomètres corporels numériques
Taper
Mode d'emploi