SunRed LH15 Manuel utilisateur

Manual Lounge heater (EN)

Handleiding Lounge heater (NL)

Handbuch Lounge heizung (DE)

Manual Lounge au gaz (FR)

LH15 - Lounge heater

www.sunred.nl

Lounge Heater EN

TECHNISCHE SPECIFICATIES

Wattage: 11.000 Watt

Element type: Gas

Certificates: CE,

Dimensions: H136cm

All measurements are approximate

User instructions - please keep for future references

www.sunred.nl

WARNlNG SAFETY RULES

PLEASE READ THE FOLLOWING SAFETY RULES PRlOR

TO OPERATION OF THE HEATER

FOR YOUR SAFETY

If you smell gas:

1ˊShut off gas to the appliance.

2ˊExtinguish any open flame.

3ˊIf odor continues, immediately call your gas supplier or your fire

Department.

FOR YOUR SAFETY

1.

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other applianceˊ

2.

An LP cylinder not connected for use shall not be stored in the

vicinity of this or any other applianceˊ

WARNlNG

1)

For use outdoors or in amply ventilated areas.

2)

An amply ventilated area must have a minimum of 25 % of the

surface area open.

3)

The surface area is the sum of the walls surface.

WARNING˖Improper installation, adjustment, alteration, service

or maintenance Can cause injury or property damage. Read the

installation, operating and maintenance instructions thoroughly

before installing or servicing this equipment.

www.sunred.nl

warning

Readtheinstructionsbeforeinstallationanduse.

-This appliance must be installed and the gas cylinder stored in

accordance with the regulations in force;

-Do not obstruct the ventilation holes of the cylinder housing;

-Do not move the appliance when in operation;

-Shut off the valve at the gas cylinder or the regulator before moving

the appliance;

-The tubing or the flexible hose must be changed within the

prescribed intervals;

-Use only the type of gas and the type of cylinder specified by the

manufacturer;

The LP tank used with your patio heater must meet the following

requirements:

Purchase LP tanks only with these required measurements:

(30.5cm) (diameter) x 57.1 cm) (tall) with 23kg capacity maximum.

-In case of violent wind particular attention must be taken against

tilting of the appliance;

www.sunred.nl

TABLE OF CONTENTS

Caution ……………………………………………………….

1

Heater Stand and Location …………………………………

2

Gas Requirements …………………………………………..

2

Leakage Test …………………………………………………

2

Operation and Storage ……………………………………...

3

Cleaning and Care …………………………………………..

4

Parts and Specifications ..…………………………………..

4

Assembly Parts and Procedures …………………………..

6

Problems Check List ………………………………………...

11

www.sunred.nl

CAUTION

PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION.

Do not use the patio heater for indoors, as it may cause personal injury or property damage.

This outdoor heater is not intended to be installed on recreational vehicles and/or boats.

Installation and repair should be done by aqualified service person.

Improperinstallation, adjustment, alteration can cause personalinjury or propertydamage.

Do not attempt toalter the unit in any manner.

Never replace or substitute the regulator withanyregulator otherthan the factory

-suggested replacement.

Do not store or use gasoline or other flammable vapors or liquids in the heater unit.

The whole gas system, hose, regulator, pilot or burner should be inspected for leaks or damage before

use, and at least annually by a qualified service person.

All leak tests should be done with a soap solution. Never use an open flame to check for leaks.

Do not use the heater until all connections have been leak tested.

Turnoff the gas valve immediately if smell of gas is detec

ted. Turn Cylinder Valve OFF.If leak is at Hose/

Regulator connection: tighten connection andperform another leak test. Ifbubbles continue appearing

should be returned to hose’s placeof purchase. If leak is at Regulator/Cylinder Valve connection: disconnect,

reconnect, andperform another leak check. If you continue to see bubbles after several attempts, cylinder

valve is defective and should be returned to cylinder’s place of purchase.

Do not transport heater while it’s operating.

Do not move the heater after it has been turned off until the temperature has cooled down.

Keep the ventilation opening of the cylinder enclosure free and clear of debris.

Do not paint the radiant screen, control panel or top canopy reflector.

Control compartment, burner and circulation air passageways of theheater must be kept clean.

Frequent cleaning maybe required as necessary.

The LP tank should be turned off when the heater is not in use.

Check the heater immediately if any of the following occurs:

-

The heater does notreach temperature.

-

The burner makes popping noise during use (a slight noise is normal when the burner is extinguished).

-

Smell of gas in conjunction with extreme yellow tipping of the burner flames.

The LP regulator/hose assembly must be located out of pathways where people may trip over it orin

area where the hose will not be subject to accidental damage.

Any guard or other protective device removed for servicing the heater must be replaced before operating the heater.

Adults and chi

ldren should stayawayfrom high temperaturesurface to avoid burns or clothingignition.

Children should becarefully supervised when they are in the area of the heater.

Clothing or other flammable materials should not behung on the heater or placed on or near the heater.

To change the gas cylinder in a amply ventilated area, away from any ignition

source (candle, cigarettes, other flame producing appliances, ...);

To check that the regulator seal is correctly fitted and able to fulfill itsfunction

showed as photo right;

To not obstruct the ventilation holes of the cylinder housing;

seal

hose

regulater

cylinder

To close the gas supply at the valve of the gas cylinder orthe regulator after use;

In the event of gas leakage, the appliance shall not be used or if alight, the gas supply

shall be shut off and the appliance shall be investigated andrectified before it is used again;

Hose/Regulatorconnection and

Regulator/Cylinderconnection

To check the hose at least once per month

ˈ

each time the cylinder is changed

ˈ

or each time before long time no use.

If it shows signs of cracking, splitting or other deterioration it shall be exchanged for new hose of the same length and of the

www.sunred.nl

s

ea

l

ho

s

e

r

e

g

u

l

a

t

e

r

cy

l

i

n

de

r

equivalentquality;

The use of this appliance in enclosed areas can be dangerous and is PROHIBITED;

Read theinstructions before using thisappliance. The appliance must be installed in accordance with the instructions and

localregulations.

For connection of hose andregulator,and connection of regulator and hose, pleaserefer to photoshowedabove.

www.sunred.nl

HEATER STAND AND LOCATION

The heater is primarilyfor outdoor use only. Always ensure that

adequate fresh air ventilation is provided.

Always maintain proper clearance to

non protected combustible materials

i.e. top 100 cm and sides 100 cm minimum.

Heater must be placed on level firm ground.

Never operate heater in an explosive atmosphere like in areas where

gasoline or other flammable liquids or vapors are stored.

To protect heater from strong wind, anchor the base securely to the

ground with screws.

100 cm

CEILING

GAS REQUIREMENTS

Use propane, butane or their mixtures gas only.

The pressure regulator and hose assembly to be used must conform to local standard codes.

The installation must conform to local codes, or in the absence of local codes, with the standard for the

storage and handling of liquid petroleum gases.

A dented, rusted or damaged tank maybe hazardous and should be checked by your tank

supplier. Never use a tank with a damaged valve connection.

The tank must be arranged to provide for vapor withdrawal from the operating cylinder.

Never connect an unregulated tank to the heater.

LEAKAGE TEST

Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas tightness

check must be performed at the installation site due to possible mishandling in shipment or excessive

pressure being applied to the heater.

Make a soap solution of one part liquid detergent and one part water. The soap solution can be applied

with a spray bottle, brush or rag. Soap bubbles will appear in case of a leak.

The heater must be checked with a full cylinder.

Make sure the safety control valve is in the OFF position.

Turn the gas supply ON.

In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas supply on and re-

check.

Never leak test while smoking.

www.sunred.nl

1.

Depress and turn control knob clockwise to OFF position.

2.

Fully open gas valve.

3.

Depress control knob and turn knob counter-clockwise to IGNITE position, then to PILOT position

(you will hear 2 clicks).

4.

With the pilot light lit, keep control knob depressed for 30 seconds.

NOTE: If the pilot light has not ignited, turn heater control knob to OFF position, fully close gas valve,

wait 5 minutes, then repeat steps 2–4 of the Lighting Instructions.

NOTE: If the pilot light ignites but does not stay lit, turn heater control knob to OFF position, fully close

propane gas valve, wait 5 minutes, then repeat steps 2–3. Now, using a lighter, ignite the pilot light

through the ignition hole on the emitter screen. Once the pilot light is lit, depress control knob for

30 seconds.

5.

After depressing the control knob for 30 seconds, turn control knob to LOW. To increase the

temperature, turn towards HIGH.

Warning˖check that no broken on the glass is found before operation.

1.

Fully close gas valve.

2.

Turn control knob clockwise to OFF position.

Variable control knob

Pointer

OFF

Off: the heater stop work

Hi: maximum temperature position

Lo: minimum temperature position

regulator

www.sunred.nl

880 mm

1360 mm

CLEANING AND CARE

•

Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that

are combustible or corrosive.

•

Remove debris from the burner to keep it clean and safe for use.

•

Cover the burner unit with the optional protective cover when the heater is not in use.

PARTS AND SPECIFICATIONS

370 mm

Flame screen guard

Burner assembly

Base of control housing

Tank housing

Base

460 mm

www.sunred.nl

A.

Constructionand characteristics

Transportable terrace/garden heater with tank housing.

Casing in steel with powder-coating or in stainless steel.

Gas hose connections with metal clamp (screw caps for Germany).

Heat emission from reflector.

B.

Specifications

Use propane,butane or their mixtures gas only.

Max. wattage: 11000 watts

Min. wattage: 5000 watts

Consumption:

APPLIANCECATEGORY:

I

3+(28-30/37)

I

3B/P(30)

I

3B/P(50)

I

3B/P(37)

TYPESOF GAS:

Butane Propane

Butane, propane

or their mixtures

Butane, propane

or their mixtures

Butane, propane

or their mixtures

GASPRESSURE:

28-30mbar 37 mbar 30 mbar 50mbar 37mbar

OUTLETPRESSURE

OFREGULATOR:

30mbar 30 mbar 30mbar 50mbar 37mbar

Using the proper regulator according to outlet pressure of regulator as showed in the table above.

C.

Table of injector

APPLIANCECATEGORY:

I

3+(28-30/37)

I

3B/P(30)

I

3B/P(50)

I

3B/P(37)

TYPESOF GAS:

Butane Propane

Butane, propane

or their mixtures

Butane, propane

or their mixtures

Butane, propane

or their mixtures

GASPRESSURE:

28-30mbar 37 mbar 30 mbar 50mbar 37mbar

TOTALHEAT

INPUT (Hs): (Qn)

11kW (800g/h)

12kW (870g/h)

INJECTOR SIZE:

1.51 mm for main burner

0.22 mm for pilot burner

1.38 mm for main burner

0.22 mmfor pilot burner

1.50 mm for main burner

0.22 mm for pilot burner

The markingˈfor exampleˈ1.51 on the injectorˈindicates that the size of injector is 1.51mm

The hose and regulator assembly must conform to local standard codes.

Regulator outlet pressure should meet the corresponding appliance category in B. Specification.

The appliance requires approved hose in 0.4m length.

www.sunred.nl

ASSEMBLY PARTS

Tools needed:

Philips screwdriver w/ medium blade

Spray bottle of soap solution for leakage test

Parts List:

Flame screen guard

A

Burner assembly

B

Cylinder Housing

C

Base

D

E

Wheel

PART DESCRIPTION QUANTITY

A

Flame screen guard

1

B

Burner assembly

1

C

Cylinder Housing

1

D

Base

1

E

Wheel

1

A

B

C

D

E

A

B

C

D

E

ASSEMBLY PARTS

HARDWARE CONTENTS (shown actual size)

AA BB

Bolt M8 X 15

Qty.2

M8

Flange

nut

Qty.2

CC

Screw M5 X 8

Qty.8

DD

M6 Dome Nut

Qty.1

EE

Philips

screwdriver

Qty.1

FF

Wrench

Qty.1

AA

CC

DD

EE FF

BB

1

ASSEMBLY PROCEDURES

1. Use 2pcs M8X15mm bolts and M8 nuts to

connect bracket with wheel to the base.

Hardware Used

D

AA

BB

M8 x 15 mm Bolts x 2

FF

Wrench x 1

E

BB

2. Use 4pcs M5X8 screw to join the tank

2

housing base and stand.

Hardware Used

C

CC

Screw M5 X 8

x 4

EE

Philips

x 1

screwdriver

CC

M8 Flange Nut

AA

BB

FF

D

AA

E BB

CC

1

2

C

EE

x 2

3

4

3. Use 4pcs M5X8 screw join the burner head

and tank housing body.

B

Hardware Used

CC

Screw M5 X 8

x 4

CC

EE

Philips

x 1

screwdriver

4. Use the M6 Dome Nut connect the two

DD

half safety guards to burner head.

A

Hardware Used

DD

M6 Dome Nut

x 1

B

C

A

3

4

CC

EE

DD

B

CC

A

5. Propane Only-Proper Hose Connection.

WARNING! Ensure the hose does not contact

6

any high temperature surfaces, or it may melt

and leak causing a fire.

After the cylinder is placed inside the heater, secure

thecylinderwithblockbelttightly.

Theheatermustbefixedonastableandstrongtable

with a minimum height of 40cm from the floor level.

6. Leak Check.

WARNING!

A leak test must be performed annually and each me a cylinder is hooked up or if a part

of the gas system is replaced.

WARNING! Never use an open ŇĂme to check for gas leaks. Be certain no sparks or open ŇĂmes are

in the area while you check for leaks. Sparks or open ŇĂmes will result in a Įre or explosion, damage to

property, serious bodily injury, or death.

Leak tes ng: This must be done before ini al use, annually,and whenever any gas Components are replaced

or serviced. Do not smoke while performing this test, and remove all sources of igni

on. See Leak Tes ng

Diagram for areas to check. Turn all burner controls to the oī posi on. Turn gas supply valve on.

Brush a half-and-half solu on of liquid soap and water onto all joints and connec ons

of the regulator, hose, manifolds and valves.

Bubbles will indicate a gas leak. Either hten the loose joint or have the part replaced with one recommended

by the Customer Care department and have the pa

heater inspected by a cer ed gas installer.

If the leak cannot be stopped, immediately shut oī the gas supply, disconnect it,and have the pa o heater inspected

by a cer

ed gas installer or dealer. Do not use the pa heater un the leak has been corrected.

7

Hose / Regulator

connec

on

Regulator / Cylinder

connec

on

5

6

PROBLEMS CHECK LIST

PROBLEM

Pilot will not light

PROBABLE CAUSE

Gas valve may be OFF

SOLUTION

Turn the gas valve ON

Tank fuel empty Refill LPG tank

Opening blocked Clean or replace opening

Air in supplysystem

Looseconnections

Purge air from lines

Check all fittings

Pilot will not stay on

Debris around pilot

Clean dirty area

Looseconnections

Thermocouplebad

Tightenconnections

Replacethermocouple

Gas leak in line Check connections

Lack of fuel pressure Tank near empty. Refill LPG tank.

Burner will not light

Pressure is low

Tank near empty. Refill LPG tank.

Opening blocked Remove and clean

Control not ON

Thermocouplebad

Turn valve to ON

Replacethermocouple

Pilot light assembly bent Place pilot properly

Not in correct location Position properly and retry

If the appliance is in case of any defaults or problems of assembly or useˈplease don’t try to modify it by yourselfˈ



contact your supplier or distributor to solve it.

Lounge Heater NL

Wattage: 11.000 Watt

Element type: Gas

Certificaten: CE

Afmeting: H136cm

BELANGRIJK – Verwijder zorgvuldig de verpakking voor gebruik, maar bewaar de veiligheidsinstructies.

Deze instructies maken deel uit van het product.

Gelieve nota te nemen van alle veiligheidswaarschuwing die in deze handleiding vermeldt worden.

Lees de instructies in hun geheel door en bewaar deze voor toekomstig gebruik.

Deze instructies dienen te worden bewaard met het product.

Dit product is voor huishoudelijk gebruik en mag niet commercieel of voor contractdoeleinden worden gebruikt.

Gebruikershandleiding – Bewaar voor eventueel toekomstig gebruik

GEBRUIKSAANWIJZING

Bewaar de instructies voor toekomstig gebruik

BELANGRIJK: VEILIGHEIDSVOORSCHRIFTEN

Lees de veiligheidsvoorschriften voor u de heater in gebruik neemt

VOOR UW VEILIGHEID

Als u gas ruikt:

1. Sluit de gastoevoer naar het toestel.

2. Doof eventueel open vuur.

3. Als geur blijft, bel dan onmiddellijk uw gasleverancier of de brandweer.

VOOR UW VEILIGHEID

1. Bewaar of gebruik geen benzine of andere ontvlambare gassen en vloeistoffen in de nabijheid

van dit of een ander apparaat.

2. Een niet aangesloten gasfles mag niet in buurt van dit of een ander apparaat worden

opgeslagen.

WAARSCHUWING

1) Voor gebruik buiten of in voldoende geventileerde ruimtes.

2) Een voldoende geventileerde ruimte houdt in dat minimaal 25% van de omringende

oppervlakken geopend zijn.

3) De omringende oppervlakken zijn de som van de omringende wand-oppervlaktes.

WAARSCHUWING: Een onjuiste installatie, aanpassing, wijziging, service of onderhoud kan

leiden tot letsel of schade aan eigendommen. Lees de installatie-, bedienings- en

onderhoudsinstructies grondig door vóór de installatie of onderhoud van dit apparaat.

WAARSCHUWING

Lees de instructies voor installatie en gebruik.

-Dit apparaat moet worden geïnstalleerd en de gasfles opgeslagen in overeenstemming met de

geldende voorschriften.

-De ventilatiegaten van de gasflesbehuizing niet afdekken.

-Verplaats het apparaat niet tijdens gebruik.

-Sluit het ventiel van de gasfles of de regelaar voor u het apparaat verplaatst.

-De leiding of de flexibele slang moet binnen de voorgeschreven intervallen worden vervangen.

-Gebruik alleen het type gas en gasfles dat door de fabrikant voorgeschreven wordt.

-De gasfles moet aan de volgende eisen voldoen: Afmeting 30,5cm diameter, 57,1cm hoogte,

23kg capaciteit.

-In geval van harde wind dient u ervoor te zorgen dat het apparaat niet kantelt en omvalt.

La page charge ...

SunRed LH15 Manuel utilisateur

Ce manuel convient également à

SunRed LH15 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents