Craftsman CM-XTEPA0024 Manuel utilisateur

Electric Tankless Water Heaters

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

1-888-895-4549 WWW.CRAFTSMAN.COM

Models:

CMXTEPA0018 (18kW)

CMXTEPA0024 (24kW)

CMXTEPA0029 (29kW)

CMXTEPA0036 (36kW)

INSTRUCTION MANUAL

2

For California residents / Pour les résidents de la Californie / Para residentes en California

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

AVERTISSEMENT: Cancer et Troubles de l'appareil reproducteur -

www.P65Warnings.ca.gov.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

Important Safety Guideline

THIS INSTRUCTION MANUAL SHOULD BE SAVED FOR FUTURE REFERENCE.

Denitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal

injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

WARNING: PLEASE READ THIS INSTRUCTION MANUAL THOROUGHLY AND COMPLETELY BEFORE INSTALLATION & USE. FAILURE TO

DO SO COULD CAUSE DAMAGE TO PROPERTY, SERIOUS INJURY OR DEATH, AND VOID YOUR WARRANTY.

Please contact us directly, should you have any questions regarding your unit.

Phone: 1-888-895-4549

3

Table of Contents

1. SAFETY GUIDELINES --------------------------------------------------------------------------------------------------------04

2. ABOUT YOUR ELECTRIC TANKLESS WATER HEATER ----------------------------------------------------------------------------04

3. SELECTING AN INSTALLATION LOCATION -------------------------------------------------------------------------------------05

4. MOUNTING YOUR WATER HEATER --------------------------------------------------------------------------------------- 05-07

5. PLUMBING REQUIREMENTS AND PRECAUTIONS -------------------------------------------------------------------------- 07-08

6. PLUMBING INSTALLATION ---------------------------------------------------------------------------------------------------08

7. ELECTRICAL REQUIREMENTS AND PRECAUTIONS -----------------------------------------------------------------------------09

8. ELECTRICAL INSTALLATION ---------------------------------------------------------------------------------------------- 09-12

9. FLOW RATE ---------------------------------------------------------------------------------------------------------------- 13

10. OPERATION GUIDE ------------------------------------------------------------------------------------------------------ 13-14

11. CARE AND MAINTENANCE --------------------------------------------------------------------------------------------------14

12. USER INTERFACE/CONTROLS -------------------------------------------------------------------------------------------- 15-16

13. TROUBLESHOOTING ---------------------------------------------------------------------------------------------------- 17-18

14. RESET UNIT ----------------------------------------------------------------------------------------------------------------18

Before Installing

By installing this product, you acknowledge the terms of the manufacturer’s warranty and authorized dealer’s return policy. Once the heater

is installed, do not return the product to the place of purchase. If you have any questions regarding the warranty or the product return

policies, please contact us by phone or email.

4

1. Safety Guidelines

Please read this manual thoroughly before installing & using the instant water heater. Failure to comply with the safety, installation or

operating instructions will void the product warranty. Manufacturer and distributor of the product will not be liable for any damage or

injury caused by the failure to comply with the installation and operating instructions speciﬁed in this manual or the improper use of the

product. Ensure that this product is installed in accordance with the national, state or local electrical and plumbing codes applicable to your

area, and as speciﬁed in our instructional guide to get the best performance from your Instant Water Heater.

This product has more than one power connection source. Do not attempt to install, clean, inspect, disassemble, service or repair the water

heater without shutting oﬀ all the power sources to the unit on the main electrical panel using the circuit breaker.

WARNING: Failure to adhere might result in severe injury or death. The water heater must be installed in compliance with all

national, state, provincial and local electrical and building regulations. We recommend that you consult a qualiﬁed electrician and

a qualiﬁed plumber if you have questions about anything relating to codes or regulations for this product.

WARNING: This product is intended for household and indoor use only. Do not immerse in water in order to avoid damage, injury

or death.

WARNING: The breaker used to power this unit must be grounded by means of the electrical panel. Failure to adhere might result

in damage, injury or death.

The heater must be directly connected to dedicated circuit breakers on the main electrical panel.

Do not install the heater where it may be subjected to direct sunlight, rain, splashing water, moisture/humidity or freezing

temperatures.

This unit is intended for heating water only. Do not attempt to use the unit for heating any other kind of liquid.

2. About Your CRAFTSMAN Electric Tankless Water Heater

Congratulations on making the decision to purchase one of the best and ﬁnest Instant Water Heaters currently available in the market today!

Your new Instant Water Heater features advanced water ﬂow rate and temperature sensors which are designed to modulate power to the

heating elements to maintain a user-selected output water temperature range for 18kW / 24kW / 29kW / 36kW: 86°F (30°C) to 122°F

(50°C) (subject to the temperature of the incoming water).

WARNING: When selecting the water temperature setting of your Instant Water Heater’s

thermostat, factors such as safety and energy conservation should be considered. Continuous

exposure of the skin to water temperatures above 120°F (49°C) can result in severe burns or

death. The maximum temperature to be set on this Instant Water Heater’s thermostat is 122°F

(50°C). Always take precaution to feel the water before bathing or showering to make sure the

temperatures are not too hot. You are required to read and comply with the Time/Temperature

Relationship Chart on the following page to determine the right water temperature for your

home.

Time/Temperature

Relationship in Scalds

120°F (49°C)

Exposure for more than 5 minutes

122°F (50°C) Around 3 minutes of exposure

WARNING: You may require a 120°F (49°C) or lower thermostat setting to prevent contact with “HOT” water, if you have small

children, disabled, or elderly persons in your home. The temperature of the water is regulated by the electronic control on the front of the

water heater.

• Children, disabled and

elderly are at high risk of

being scalded.

• See instruction manual

before setting your desired

hot water temperature

• Always feel water before

bathing or showering

5

3. Selecting an Installation Location

• This Water Heater is designed for indoor installation only.

• It should not be installed in a location where it might be subjected to freezing temperatures as the freezing of the water in the Water

Heater can lead to severe and irreversible damages which are not covered under your warranty.

• The Water Heater should not be placed in a location that is diﬃcult to access.

•

WARNING: Ensure that the water heater, as well as the power supplies and water connections, are out of reach of children

as the outlet water pipe can get very hot and touching can lead to injury.

• Avoid installing your tankless water heater in a location prone to excessive humidity, moisture, or dust, or in an area where it may

be splashed with water or other liquids.

WARNING: DO NOT install underwater pipes or air conditioning lines that might leak or condense moisture that could then

drip onto the heater.

WARNING: DO NOT install above electrical boxes or junctions.

• Do not install in areas which can be damaged due to leakage from the Water Heater. However, safety measure such as suitable drip

pan or an active water leak detector and shutoﬀ valve should be installed in such areas that cannot be avoided.

Item # Unit dimensions (inches) Weight (lbs) Connections

CMXTEPA0018 (18kW) 15.52 x 4.49 x 13.9 9.21 1/2”

CMXTEPA0024 (24kW) 18.74 x 4.53 x 14.76 12.17 3/4”

CMXTEPA0029 (29kW) 18.74 x 4.53 x 14.76 12.17 3/4”

CMXTEPA0036 (36kW) 23.23 x 4.53 x 14.77 16.23 3/4”

WARNING: Water heaters are heat producing appliances. In order to avoid damage, injury or death, there shall be no materials

stored against the water heater and proper care shall be taken to prevent unnecessary contact (especially by children) with the

water heater. UNDER NO CIRCUMSTANCES SHALL FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR

STORED IN THE VICINITY OF THIS WATER HEATER OR ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER.

4. Mounting Your Water Heater

1. Your tankless water heater should be secured to a solid mounting surface with four screws, (minimum 1” (25.4mm) long).

2. Ensure that the unit is level before fastening the screws in place.

3. The unit must be installed in an upright position with the water inlet and outlet at the bottom of the unit. Do not install inversely

with connections facing up or sideways with connections facing right or left.

4.

WARNING: Do not install the unit above electrical boxes or junctions.

5.

WARNING:The water heater must be installed in a manner that prevents contact with ﬂammable liquids and gases. Keep

these ﬂammable materials at least two feet away from the heater and the hot water outlet pipe. The water heater and the hot water

outlet pipe must be secured, and out of children’s reach to prevent tampering with controls or contact with an extremely hot pipe.

6. If installing the heater on an upper ﬂoor or attic, make sure installation complies with the local codes. Install a drip pan with

drainage, or a leak detector and automatic shutoﬀ valve, to prevent damage in case of any leakage.

6

24kW, 29kW

18W

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

118

º

F

temp

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

118

º

F

temp

a. Remove the appliance cover. (Heater cover) (ﬁgure 3)

b. Mount the unit on the wall with 4 screws at the marked points (ﬁgure 4)

c. Make sure the unit is leveled horizontally, with water inlets and outlets at the bottom (ﬁg.5)

D. Make sure the unit includes the water pre-ﬁlter (ﬁg.6)

7

Recommended clearances: 12” (304.8mm) above and below the heater

6” (152.4mm) in front of and to the sides of the heater

WARNING: Please keep any ﬂammable materials at least 24” (609.6mm) away from the water heater and hot water outlet pipe.

5. Plumbing Requirements and Precautions

• Please follow all plumbing instructions carefully. This product must be installed in accordance with all national, state, provincial,

and local plumbing codes. We recommend consulting with your municipality or a qualiﬁed plumber if you have questions relating

to plumbing codes for your area prior to installing.

• The plumbing installation must be completed before the electrical installation.

• DO NOT solder any pipe with the unit connected to the pipe. The heat from soldering may cause

damage to the ﬂow sensor. Doing so will void the warranty.

• The use of a temperature pressure relief valve (T&P) is not required for most installations because

the tankless water heater does not use a storage tank. UL Standard 499 does not require that a

pressure relief valve is used, although it may be needed to meet installation codes in your area.

In such cases, the pressure relief valve should be installed in accordance with local codes. It is

important to ensure that the unit is operating correctly, and that air is purged from the valve prior

to installing the water heater.

• A T&P valve is recommended for added safety when connecting to plumbing rated Metal, Flex or High-Temperature CPVC piping.

NOTE: A pressure relief valve is required for installations in the Commonwealth of Massachusetts and State of

Kentucky. Please check your local installation codes for any special requirements.

• The plumbing installation requires piping that can withstand pressure up to 120PSI / 8 BAR.

• The maximum operating water pressure for this unit is 150PSI / 10BAR. Residential plumbing systems with unstable pressure or

36W

Fig. 3 Fig. 4

Fig. 5

Do not install upside down

or on its side

Fig. 6

Water Pre-

Filter

118

º

F

temp

Fig. 7

Do not solder any piping to the

unit’s Connection points

8

pressure above 5 BAR require the application of a pressure reduction valve set to 60-75PSI / 4-5 BAR for optimal performance.

• The water supply ﬂow rate must be at least 0.5 Gallons per Minute (GPM) to ensure proper operation.

• Flexible water hoses are recommended to be used with your water heater when installing your water heater. When connecting

the inlet water pipe to the unit, use a wrench to hold the unit’s connection, and another wrench to tighten so that the ﬂow sensor

on the unit will not be loosened or damaged. Do not over-tighten the water inlet and outlet connections to avoid severe internal

damage to the water heater.

• We recommend the installation of a manual shut-oﬀ valve (ball valve) on the inlet and outlet of the water heater to create a

convenient shut-oﬀ point if future maintenance or servicing is required. Before connecting the pipes to the water heater, it is highly

essential to ﬂush the lines to eliminate all the plumbing paste or residue in the lines caused by any welding or soldering.

• All the water pipes within 3 feet (1 meter) of the inlet and outlet connections are recommended to be rated for high-temperature

applications with 150°F (66°C) minimum.

• Before proceeding to the electrical installation, run water through the unit for several minutes to ﬂush out any air bubbles from the

water line.

6. Plumbing Installation

STEP 1: Thoroughly ﬂush cold supply line of debris.

STEP 2: Connect the HOT WATER line to the water heater OUTLET. The water heater outlet can be seen on the left side of the heater when

facing the unit. Connect the COLD-WATER line to the water heater marked COLD WATER INLET which is located on the right side when

facing the unit.

* Pre-heated water can be connected to the cold water inlet, where this unit will act as a booster.

STEP 3: After tightening both ﬁttings at the water heater, several hot water faucets should be opened to allow the ﬂow of water through

the water heater for at least 2 to 3 minutes. This process purges all the air from the water lines and MUST be performed before turning on

the power at the unit.

FAILURE TO FOLLOW THIS STEP MIGHT CAUSE PERMANENT DAMAGE TO THE HEATING ELEMENTS. (The power to the heater should be

turned oﬀ and the air purged out of the lines before turning the power on anytime maintenance is performed on the water heater or the

homes plumbing system, as air might have been introduced into the plumbing pipes.)

STEP 4: Carefully inspect all connections, units, and the pressure relief device for leaks after the plumbing installation is completed. If there

are no leaks present, you can proceed to the electrical installation.

CAUTION: If you detect a water leak from the water heater at this point, turn oﬀ the water supply at the shut oﬀ valve on the unit’s

incoming water supply and contact us at 1-888-895-4549.

Plumbing Specications

Minimum water ﬂow to activate the unit 0.5 gpm

Working pressure 0.5–10 BAR (7–150 psi)

Tested pressure (maximum) 20 BAR (290 psi)

Water connections 18kW 1/2” NPT

Water connections 24, 29, 36kW 3/4” NPT

9

7. Electrical Requirements and Precautions

Manufacturer recommends that this product be installed in accordance with all applicable national, state, provincial, and local electrical

codes. Consult a qualiﬁed and licensed electrician if you have questions or are unsure about anything relating to codes for this product. The

heater must be connected to a dedicated circuit breaker on the main electrical panel.

WARNING: As with all electrical appliances, it’s crucial to ﬁrst shut oﬀ all power to the unit directly at the fuse or breaker box before

attempting to install, repair or disassemble this water heater. Ensure that the breaker is shut oﬀ. SERIOUS BODILY INJURY OR DEATH COULD

OCCUR IF YOU IGNORE THIS WARNING.

CAUTION: All wiring (wire gauge), as well as circuit protection (breaker), must comply with the U.S. National Electrical Code (NEC)

in the USA or the Canadian Electrical Code (CEC) in Canada. Failure to do so could lead to property damage, personal injury, and void your

warranty.

Note: The Canadian Electrical Code generally requires that all supply wires and corresponding circuit protection used for domestic hot water

heating and hydronic heating applications be sized to a minimum of 125% of the maximum current rating of the heater (check heater

speciﬁcation details below).

Before installing this tankless water heater, ensure that suﬃcient electrical power is available in the home to handle the maximum

amperage load of the applicable heater.

IMPORTANT NOTES:

The heater requires set of wire and ground (see wiring diagram on page 10-11)

• Please see electrical speciﬁcations by heater input and wiring diagram on the page 10-11 for additional electrical information.

8. Electrical Installation

STEP 1: Take the wire pair and connect to the breaker (see wiring diagram). Be sure that the breaker is connected to one black wire and

one red wire. Be sure the power to the unit is shut oﬀ using the dedicated circuit breakers in the main electrical panel.

STEP 2: Run the correct set of power cable wires from the circuit breaker in the main electrical panel to the water heater by utilizing a

suitable wire gauge which meets all applicable electrical codes for the size of the breaker. Then, connect the power cable to the block

terminal within the water heater.

STEP 3: Unit requires a ground conductor for the incoming circuit.

STEP 4:

DOUBLE CHECK the electrical connections and ensure the wire connections are correct, tight and secure. It’s important to

conﬁrm that the right breaker size and wire gauge has been used and that the unit has been connected to a ground in accordance with

applicable codes. Be sure to reattach the front cover of the unit with two screws.

STEP 5: Ensure that all the air has been purged from the water lines before turning on power to the unit. Refer to STEP 3 in the plumbing

installation section. Restore power to the unit through the dedicated circuit breaker in the main electrical panel.

It is crucial to follow the wire connection as shown and ensure all connections are made correctly for proper operation of the

unit. The unit will not operate correctly, even though it turns on and otherwise appears to function, if you mix up one set of wire

with another.

10

Electrical Specications by Heater Input

Item # kW Max Amps Required Breaker Req. Wire Size

18kW 18 75 2 x 40A Double Pole 2 x 8/2 AWG with Ground

24kW 24 100 3 x 40A Double Pole 3 x 8/2 AWG with Ground

29kW 28.8 120 3 x 40A Double Pole 3 x 8/2 AWG with Ground

Power Rates

Item # 240V 220V 208V

18kW 18,000 Watts 15,125 Watts 13,520 Watts

24kW 24,000 Watts 20,166 Watts 18,026 Watts

29kW 28,800 Watts 24,200 Watts 21,632 Watts

Your tankless water heater is now installed and ready to use! Follow the General Operating Instructions to complete the setup.

Terminal Block in Unit

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

Unit Requires 10 AWG ground wire - one for each 240V circuit

L1L1 L2

8/2 AWG

L2

240V

L1 L2 L1 L2

L1L1L1 L2

8/2 AWG

L2L2

240V

L1 L2 L1 L2 L1 L2

Wiring Diagram for 18kW

Wiring Diagram for 24kW, 29kW

11

Electrical Specications by Heater Input

Item # kW Max Amps Required Breaker Req. Wire Size

36kW 36 150 4 x 40A Double Pole 4 x 8/2 AWG with Ground

Power Rates

Item # 240V 220V 208V

36kW 36,000 Watts 30,250 Watts 27,040 Watts

Your tankless water heater is now installed and ready to use! Follow the General Operating Instructions to complete the setup.

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

40 Amp

Double Pole

Unit Requires 10 AWG ground wire - one for each 240V circuit

L1L1L1 L2

8/2 AWG

L2L2

240V

L1 L2 L1 L2 L1 L2

L1 L2

240V

L1 L2

8/2 AWG

Your tankless water heater is now installed and ready to use! Follow the General Operating Instructions to complete the setup.

Terminal Block in Unit

Wiring Diagram for 36kW

12

Testing the connections from your Breaker Panel to your unit

1. Measure the voltage by using AC multimeter.

2. Verify All circuit breakers are in the ON position. DO NOT turn on water while conducting this test or turn on unit.

3. Make sure your Multimeter is set to testing Voltage and in AC position.

4. Place the multimeter probes between each L1-L2 pairing on the terminal block (see drawing) – Each pairing should read approximately 240V.

5. Place the multimeter probes between each L1-L1 pairing and L2-L2 pairing on the terminal block (see drawing) - Each pairing should

read approximately 0V.

TERMINAL BLOCK IN THE UNIT

Measurement 1- Vac

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

L1 L2

240V

TERMINAL BLOCK IN THE UNIT

Measurement 2- Vac

L1 L2

0V

240V

L1 L2

0V

240V

L1 L2

0V 0V

240V

L1 L2

0V 0V

240V

L1 L2

240V

L1 L2

0V 0V 0V

240V

L1 L2

0V 0V 0V

240V

L1 L2

240V

L1 L2

240V

18kW

24kW/ 29kW

36kW

13

9. Flow Rate

The chart below indicates maximum temperature rise for a given ﬂow rate

TEMPERATURE RISE CHART (GPM)

Item # kW 30°F 40°F 50°F 60°F 70°F

CMXTEPA0018 (18kW) 18 1.75 GPM 2.04 GPM 2.46 GPM 3.06 GPM 4.1 GPM

CMXTEPA0024 (24kW) 24 5.2 GPM 3.95 GPM 3.52 GPM 3.3 GPM 2.4 GPM

CMXTEPA0029 (29kW) 28.8 5.9 GPM 4.5 GPM 3.87 GPM 3.47 GPM 2.8 GPM

CMXTEPA0036 (36kW) 36 6.2 GPM 5.15 GPM 4.4 GPM 3.9 GPM 3.1 GPM

Based on 105°F Output Water Temp / GPM = Gallons Per Minute

10. Operation Guide

Operating your new tankless water heater is similar to using any traditional water heating system. However, it is essential that you carefully

read all setup procedures, operating instructions and tips to ensure the maximum performance and energy savings from your new water

heater. We recommend that all members of the household read these General Operating Instructions.

This electric water heater is designed to supply hot water. The unit contains heating elements within, capable of heating water quickly on-

demand for as long as you need it. Unlike a conventional tank storage water heater, this unit is a tankless water heater that does not store

hot water. However, once you begin using the system, you will understand it works like a conventional tank system.

Tankless system delivers hot water instantaneously on demand. Since a tankless system does not waste energy continually when heating

water, i.e. idly sitting and losing heat in a storage tank, it provides signiﬁcant energy savings than a conventional water heater.

With your new system, as soon as you turn on the hot water faucet, the demand for hot water is detected by a ﬂow sensor, and the high-

power heating elements are activated. Sensors continually monitor the water ﬂow rate and measured the incoming and outgoing water

temperature. Data is transmitted to the system logic controls, which determines the exact amount of power required by heating elements

to heat the water to your desired temperature.

It is essential to keep in mind that all tankless water heaters are subject to a maximum ﬂow rate. If this ﬂow rate is exceeded, the heater will

not be capable of suﬃciently heating water.

Also keep in mind that conventional tank heaters are set to high temperatures to prevent running out of hot water quickly, and thus a large

amount of cold water needs to be mixed in to reach a comfortable level for washing and showering. Since this unit heats water on demand,

it is designed to heat to a lower temperature. This means you only need to mix in a small amount of cold water or none at all.

Your hot water supply may also be aﬀected by the incoming water temperatures as the season diﬀers. During winter, if the incoming water

temperature is frigid, you might not be able to run multiple hot water outlets at the same time as compared to the summer. However, you

can run showers back-to-back without having to wait for the water to heat.

Water Quality: One of the things which should be taken into consideration when installing and maintaining the water heater is the

quality of water. Water conditions outside the recommended levels outlined below are not permitted and can damage the water heater. We

reserve the right to deny any warranty claim regarding damage suﬀered due to use in water conditions that are not in accordance with the

table below. The water must be treated, and the heater ﬂushed regularly when this product is installed in an area that is known to have hard

water that causes scale build-up to prevent damage to the heat exchanger and heating elements. We recommend that a water treatment

device or water softener should be installed to maintain optimal performance of the water heater in hard water areas.

14

Chart for Recommended Water Quality levels

pH Total Dissolved

Solid (TDS)

Free CO2 Total

Hardness

Aluminum Chloride Copper Iron Manganese Zinc

6.5

-

8.5

Up to

500

mg/L

Up to

500

mg/L

Up to 200

mg/L

Up to

0.2

mg/L

Up to 250

mg/L

Up to 1.0

mg/L

Up to

0.3

mg/L

Up to

0.05

mg/L

Up to 5

mg/L

11. Care and Maintenance

To ensure maximum performance of your water heater and to reduce the risk of a water leak, we recommend the following maintenance:

• The water heater has minimally required maintenance procedures. Periodic inspections and tests are always recommended for

signs of damage or failure. Any damage, cracks, leakage or weakness should be addressed and ﬁxed immediately. Do not over

tighten any of the connections. Over tightening the connection points could cause severe internal damage to the unit.

• Remember that water heated at higher temperatures produces scale buildup much faster than at lower temperatures. Having

manual shut-oﬀ/maintenance valves installed on the inlet and outlet of the water heater will allow access to ﬂush the unit with a

descaling solution. We recommend routine maintenance once a year or once every six months if the water supply has an unusually

high level of mineralization (hard water)

• Clean the pre-ﬁlter on the inlet water side once every six months. Wash lightly to remove any debris.

When any form of maintenance is carried out on the water heater or the home’s plumbing system that may introduce air into the plumbing

pipes, it is crucial to power oﬀ the water heater and purge the air out of the lines before allowing the unit to power up.

FAILURE TO DO SO COULD RESULT IN PERMANENT DAMAGE TO THE HEATING ELEMENT AND VOID YOUR WARRANTY.

When air is introduced into the plumbing system, follow the steps below to ensure the unit can safely resume operation.

1. Shut oﬀ all power connections to the unit at the circuit breaker on the main electrical panel.

2. Perform the maintenance or servicing tasks.

3. Open one or more hot water faucets and allow water to run through the unit for several minutes to purge any air from the heater

and water lines.

This step must be performed before turning on power to the heater. Failure to complete this step may cause permanent

damage to the heating elements.

4. Reconnect power to the unit at the circuit breaker on the main electrical panel. Press and switch the ON position.

5. With the water running through the unit, check and reset the temperature if necessary. The recommended temperature setting is

118°F (48°C).

15

12. User Interface/Controls

Power

• Press

button, the display will turn on

• Press

button again, the display will turn oﬀ

Setting the Output Water Temperature

• To set the temperature, ﬁrst turn on a hot water faucet and allow

water to run through the heater. The digital display lights up and

shows the current temperature setting.

• To increase or lower the temperature setting, press

increase the

temperature or

to decrease the temperature.

• Temperature can be set to any temperature from 86°F (30°C) to

122°F (50°C).

• A comfortable temperature for bathing and showering is between

105°F (41°C) and 110°F (43°C).

• The recommended temperature setting is 118°F (48°C), which will deliver hot water for all household needs at a maximum water

ﬂow rate.

CAUTION: A higher temperature setting is not recommended, as it can cause severe scalding injuries to children and elderly

persons. Higher temperatures also produce more scale buildup in water heating devices.

118

º

F

temp

Press button to raise the

temperature (up to 122°F / 50°C)

or Press button to lower the

temperature (as low as 86°F / 30°C)

16

Starting the system for the rst time

1. Press

button, to activate the heater to display outlet temperature.

2. With the water running through the unit, press

or to adjust the temperature.

Freezing Temperatures

If the ambient temperature falls below 32°F (0°C), protect the heater from potential damage. Power oﬀ the unit using the dedicated circuit

breaker on the main electrical panel. Open a faucet slightly to cause water to ﬂow continuously through the device at a very low rate,

without heating. Restore power to the unit when temperature condition is normal.

If the water inside the heater freezes, it can cause damage that is not covered by warranty. If you suspect water has frozen within

the unit, do not turn it on until you are sure the frozen water has melted, and there are no leaks in the unit. It is recommended to contact a

qualiﬁed electrician or the manufacturer for service in this situation.

118

º

F

temp

Digital temperature display

Temperature setting Buttons

Power Button

Cold water inlet

Hot water outlet

(to be connected to the main hot water pipe)

17

Digital temperature display

Temperature setting Buttons

Power Button

Cold water inlet

Hot water outlet

(to be connected to the main hot water pipe)

13. Troubleshooting

Before calling for service, check the troubleshooting list of common issues.

If you are unable to resolve a problem, contact your locally authorized distributor.

PROBLEM ISSUE POSSIBLE CAUSE SOLUTION

No hot water and

display do NOT

light up

Power outage or faulty wiring. Check the power supply. Check the circuit breakers.

Make sure the breakers at main electrical panel are ON. You may have a faulty

breaker or unit may be wired incorrectly.

Make sure the shutoﬀ valve on the unit’s incoming water supply line is fully

open.

The ﬂow rate needed to

activate the heating element

(0.5 gpm) has not been

reached.

Increase the ﬂow rate from the water supply source.

Clean the ﬁlter screen on the unit’s water inlet.

No hot water

and display DOES

light up

Reset the unit Refer to manual (Page 18) for diagram of reset points.

Make sure to shut all power on your breaker panel before attempting to

reset unit. All resets must be pressed.

Potential internal part failure Please call us for further technical assistance.

Water is heated,

but not hot

enough.

The water ﬂow rate exceeds the

heating capacity of the heater.

Reduce the water ﬂow rate at the faucet or slightly close the shutoﬀ valve on the

unit’s incoming water supply line to reduce the water ﬂow rate.

Voltage less than 240 Volts The heating elements on your water heater are designed for 240 volts. When

used with a lower voltage, they produce less heating power. You may need to

upgrade to a larger input heater.

Crossed Wires. If it’s a new installation, double check the wiring to conﬁrm that it is correct.

Temperature setting is too low. Increase the temperature setting on the unit.

Water pressure is less than 0.5

bar (7 psi).

Make sure the shutoﬀ valve is fully open, and the water supply line is not

blocked.

Mixing too much cold water You do not need to mix as much cold water with your tankless water heater

compared to when you use a conventional water heater. You may also have an

anti- scald feature on your faucet that is mixing cold water. These types of faucets

can usually be adjusted to reduce the amount of cold water mixed.

Thermal loss due to long pipe

run.

As the hot water from the heater runs through the hot water delivery system to

your faucet, some heat will be lost especially if it has long distance to travel or

the pipes are cold. This is normal. You can compensate for this by increasing the

setting on your water heater if you need/ want hotter water.

Water is heated,

but not hot

enough.

Voltage less than 240 Volts The computer chips in your tankless water heater are programmed with the

expectation that your incoming line voltage is 240 volts. If you have less than

240 volts [i.e. 208V or 220V], it may aﬀect the reading on your water heater’s

digital display and cause it to read slightly higher than the actual output

temperature. To compensate for this, increase the setting on your water heater if

you need or want hotter water.

Water is too hot. The water ﬂow rate through

the heater is too slow.

Increase the ﬂow rate at the water outlet.

Temperature setting is too high Switch to a lower temperature setting.

Water Temperature at faucet is

too hot.

Check for too little ﬂow, or if the set point temperature is too high. This could

possibly indicate a possible internal part failure. Call us for technical assistance.

18

Heater shuts oﬀ

during use.

Power outage or faulty wiring. Check the power supply. Check the circuit breakers.

If the problem persists, please call us for further technical assistance.

Water stops

ﬂowing.

Possible Blockage in water

pipes or hoses.

Make sure the main water line valve is fully open, and there are no obstructions

in the water supply line.

Water

temperature

varies from hot to

cold during use.

Water pressure has dropped

below a minimum level.

Increase the ﬂow rate from the water supply source.

14. Reset Unit

As with all electrical appliances, it is crucial to ﬁrst shut oﬀ all power to the unit directly at the fuse or breaker box before attempting to

reset this water heater.

WARNING: SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

Locate the three reset button locations as shown below and press all buttons. If you hear a “click,” the unit has reset. If you ﬁnd that the unit

needs to be reset quite often, please call our customer service for further assistance. Proceed to turn on your breakers and power on the unit.

18kW

24kW, 29kW

36kW

19

LIMITED WARRANTY

For service, repair or any questions regarding your water heater, call the appropriate 800 number listed within this section. Please DO NOT

return the product to the place of purchase. Also, DO NOT mail the product back to the manufacturer, nor bring it to a service center without

proper instructions and permission from one of our representatives.

The terms of this warranty are solely subject to the original owner and are at no time transferable. A transfer of ownership will result in

immediate termination of this warranty. This warranty is valid only if the product is purchased from an authorized reseller that has an

established direct relationship with the manufacturer.

The manufacturer warrants to the original owner that our instant water heaters will be free from defect in workmanship and material for

TWO YEARS from the date of purchase, and free from leakage for SEVEN YEARS from the date of purchase. Should any part(s) prove to be

defective during this period, the manufacturer will only be responsible for a replacement water heater or replacement of the defective

part(s). The manufacturer is not responsible for labor charges or any incidental or consequential expenses. If a replacement water heater or

part is not available, the manufacturer’s liability is limited to the cost of the water heater or $1,000.00, whichever is less. The manufacturer

is not an insurer, and the original owner should purchase insurance to cover damage to property or belongings. The original owner agrees

to waive their right to jury trial or to participate in a class action. Also, the original owner agrees to waive subordination to the extent a loss

is covered by insurance, so that their insurance company cannot proceed with action against the manufacturer for recovery of any claims.

Furthermore, all requests must be arbitrated in the state of New Jersey.

Should the owner wish to return the water heater for repair, the owner must ﬁrst secure written authorization from the manufacturer. The

owner shall be required to show proof of purchase date and to pay all transportation costs to return the defective part(s) or water heater for

repair or replacement. Warranty is void if: (i) water heater has been installed or used improperly; (ii) design has been altered in any way; (iii)

water heater has been installed and/or serviced by someone other than a licensed electrician; (iv) or if the water heater has been installed

or used in contradiction to installation instructions, applicable laws and/or ordinances.

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

Product manufactured by: (or “distributed by”)

Producto fabricado por:

Produit fabriqué par:

PARAGON GROUP USA LLC.

Englewood, New Jersey, 07631, USA

U.S. & Canada Only • É.-U. et Canada seulement

www.CRAFTSMAN.com • 888-331-4569

Notes:

P.N. 107336

La page charge ...

Craftsman CM-XTEPA0024 Manuel utilisateur

Ce manuel convient également à

Craftsman CM-XTEPA0024 Manuel utilisateur

dans d''autres langues

Autres documents