INSTEON Refurbished Remote Control Plug-In Lamp Dimmer Module Manuel utilisateur

Insteon Dimmer Module

Owner’s Manual

Insteon Dimmer Module

Owner’s Manual

Contents

Getting Started

Insteon Dimmer Module 4

Device Overview

Buttons

Installation

Leave Your Lamp On

Insteon Links

Understanding Linking 6

Links are One-Way

Links Remember a Device’s State

Controllers

Responders

Controller-Only 7

Responder-Only

Grouping Devices

Use Cross Linking

Insteon Hub

Linking to the Insteon Hub 9

Manual Linking

Linking with a Single-Button Controller 11

Linking with a Multi-Button Controller 12

Multi-Linking or Making a Scene 13

Unlinking from a Single-Button Controller 14

Unlinking from a Multi-Button Controller 15

Multi-Unlinking or Removing a Scene 16

Local Programming

About Local Programming 18

Load Sense 19

Hardware Reset

Factory Reset 21

Software-Only Features

Beep on Button Press 23

Disable Local Programming

Blink on Trac

Error Blink

Appendix

Specications 26

Troubleshooting 29

Certications and Warnings 31

Product Warranty 32

3

Everything you need to quickly get up and running.

Getting Started

Everything you need to quickly get up and running.

Getting Started

4

Leave Your Lamp OnInstallation

ButtonsDevice Overview

Insteon Dimmer Module

Set Button

On

O

Status LEDOn

O

®

Plug your lamp into the bottom of the

Dimmer Module and plug the Dimmer Module

into an unswitched wall outlet.

Tap to turn o

Double-tap to turn o instantly

Press and hold to dim

Tap to turn on

Double-tap to turn on instantly

Press and hold to brighten

See sections on Basic Linking and

Local Programming for set button

functions

®

If your lamp’s switch is OFF, the Dimmer Module

will be unable to remotely control your lamp.

ON

5

Insteon devices can stand alone and function as a local switch or dimmer,

but their real power comes when they are connected together to form a

control system. Most Insteon devices can control one another and be the

recipient of control. The process of associating multiple Insteon devices to

one another is called Linking.

Insteon Links

Insteon devices can stand alone and function as a local switch or dimmer,

but their real power comes when they are connected together to form a

control system. Most Insteon devices can control one another and be the

recipient of control. The process of associating multiple Insteon devices to

one another is called Linking.

Insteon Links

6

When linking Insteon devices, the links that

are created are one-way.

The current state of the controlled device is

stored in the link: on, o or dimmed.

Switch A will turn Switch B on and o but

Switch B cannot turn Switch A on or o.

The switch will turn on the Dimmer Module

to 75% brightness.

A SwitchB Dimmer Module

NEW

X

NEW

X

75%

Insteon devices that can turn other devices on

or o are called controllers.

Sensors, Switches, Keypads and the

Hub are common controllers.

NEW

X

Insteon devices that receive the command of a

controller are called responders.

Switches, LED Bulbs, Plug-In Modules and

Micro Modules are common responders.

NEW

X

RespondersControllers

Links Remember a Device’s StateLinks are One-Way

Understanding Linking

Neutral

On

Off

Set

N

Load L1

Line L

7

Controller-Only

Some devices like sensors can only control

other devices.

The Motion Sensor will turn on the Switch

but the switch cannot control the Motion

Sensor.

Motion Sensor

NEW

X

Responder-Only

Some devices cannot control other devices;

these devices only receive Insteon commands.

Some devices can only link as

responders to devices and scenes.

LED Bulb Dimmer SwitchDimmer Switch

NEW

X

Understanding Linking

Grouping Devices Use Cross Linking

You may want to group together two

devices, for example, in a virtual-three way

conguration. For Insteon, this is called Cross

Linking.

To Cross Link, simply turn on the devices and

perform the linking process twice, once in

each direction.

To group Switch A and B so that they each

control one another and the connected

load, Cross Linking is necessary.

Link Switch A to Switch B and repeat to link

Switch B to Switch A.

NEW

X

NEW

X

A AB BLoad

8

The Insteon Hub allows you to congure your device, customize its

properties, create scenes and more, all from your smartphone or tablet.

Insteon Hub

The Insteon Hub allows you to congure your device, customize its

properties, create scenes and more, all from your smartphone or tablet.

Insteon Hub

9

You can now control your Dimmer

Module from the Insteon Hub.

Linking to the Insteon Hub

1

4

From Rooms, navigate to All Devices.

When prompted, press and hold the

set button on your Dimmer Module

until the device double-beeps.

®

Rooms

All Devices Check-In Favorites

Bathroom Bedroom Hallway

Kitchen Living Room Outside

72º

Add Device

Plug-In Module Wired In

LED Bulb Thermostat

3

Select Plug-In Module form the list of

devices.

2

Tap the Add button.

All Devices

Back Door Bathroom Bedroom

Font Door Garage Door Garage Light

Motion Sensor Outside Lights

72º

Add

10

When not using a central controller like the Insteon Hub, Insteon devices

can be congured and linked manually on a device-to-device basis. It is

strongly advised that you not perform manual linking when using a central

controller. Instead, let your central controller handle the linking for you.

Manual Linking

When not using a central controller like the Insteon Hub, Insteon devices

can be congured and linked manually on a device-to-device basis. It is

strongly advised that you not perform manual linking when using a central

controller. Instead, let your central controller handle the linking for you.

Manual Linking

11

Linking with a Single-Button Controller

2

Make sure the Dimmer Module is

On and then press and hold the

Dimmer Module’s set button until

the device double-beeps.

1

On your Insteon controller, press

and hold the set button until the

device beeps.

Manual Linking Only

®

Your Insteon controller will now

control your Dimmer Module.

12

A

B

Linking with a Multi-Button Controller

2

Make sure the Dimmer Module is

On and then press and hold the

Dimmer Module’s set button until

the device double-beeps.

1

On your Insteon controller, tap the

desired control button and then

press and hold the set button until

the device beeps.

®

Your Insteon controller will now

control your Dimmer Module.

Manual Linking Only

13

Multi-Linking or Making a Scene

2

3 4

Adjust your scene members to

their desired state: on, o, or

brightness level if dimming.

Lamp 1

Lamp 3

Lamp 2

Appliance

One at a time, press and hold the

set button on each scene member

until it double-beeps.

Tap the set button on your Insteon

controller to nish building your

scene.

1

On your Insteon controller, press

and hold the set button until the

device beeps, then tap the set

button.

50% 72%

30%

ON

®

A

B

Your Insteon controller will now

control your scene.

Manual Linking Only

14

Unlinking from a Single-Button Controller

1

On your Insteon controller, press

and hold the set button until the

device beeps.

2

Press and hold the set button

again until the device beeps.

3

Press and hold the Dimmer

Module’s set button until the

device double-beeps.

®

X

Your Insteon controller will no longer

control your Dimmer Module.

Manual Linking Only

15

A

B

1

On your Insteon controller, tap the

desired control button and then

press and hold the set button until

the device beeps.

Unlinking from a Multi-Button Controller

2

Press and hold the set button

again until the device beeps.

3

Press and hold the Dimmer

Module’s set button until the

device double-beeps.

®

X

Your Insteon controller will no

longer control your Dimmer Module.

Manual Linking Only

16

Multi-Unlinking or Removing a Scene

2

3

One at a time, press and hold the

set button on each scene member

until it double-beeps.

Tap the set button on your Insteon

controller to exit Multi-Unlinking

mode.

1

On your Insteon controller, press

and hold the set button until the

device beeps. Press and hold the

set button again, then tap the set

button.

®

A

B

C

®

X

Your Insteon controller will no longer

control your Insteon responders.

Manual Linking Only

17

Use the local programming to set local on-level, ramp rates and even

perform a factory reset.

Local Programming

Use local programming to set local on-level, ramp rates and even perform

a factory reset.

Local Programming

18

About Local Programming

Local Programming Features

Linking Mode Readies the module for linking to another Insteon device. As linking is directional, the rst device placed

into linking mode will become the controller in the controller/responder relationship. The second device will

become the responder. The device automatically exits linking mode after a link has been made with another

Insteon device or four minutes have elapsed without linking.

Multi-Linking

Mode

Readies the module for linking to multiple Insteon devices. The module will remain in linking mode for 4

minutes or until the module’s set button is tapped. This mode is very usefully for manually creating scenes.

Unlinking

Mode

Allows the removal of links from the Insteon device. The device will automatically exit unlinking mode after a

link has been removed from another Insteon device or four minutes have elapsed without linking.

Multi-

Unlinking

Mode

Allows the removal of multiple links from the Insteon device. The device will stay in unlinking mode for 4

minutes or until the device’s set button is tapped.

LED

Brightness

Allows adjusting the brightness level of the module’s status LED.

RF Beacon Places the device in a mode that broadcasts a signal over Insteon RF. Any devices beeping or displaying a

blinking LED are within range of the module’s RF signal.

Factory Reset Erases any user-customized programming from the device including all Insteon device links, scenes, ramp

rate, on-level, etc. A factory reset cannot be undone.

To move right, press and

hold the set button

To move down, tap the set

button

Status LED blinks green

Status LED double-blinks

green

Status LED blinks red

Status LED double-blinks

red

The Local Programming Flowchart is a visual

representation of the device’s settings. Many

device features can be congured using this

diagram. Some devices have more options

than others but the Local Programming

Flowchart presents even the most

complicated devices with a straightforward,

navigable path.

If using the Insteon Hub or any other central

controller, it is strongly advised that you

not use Local Programming. Your central

controller can manage the device properties

and links for you.

Navigation Local Programming

Using a Central Controller

NEW

X

19

Load Sense

Linking Mode

Disable

Load Sense

SOLID

Enable

Load Sense

SOLID

Press

Tap 2x Tap 3x

Exit

Disable

Enable

20

Chapter explanation

Chapter Title

A factory reset will erase all links stored in the device’s database as well as

any customized properties.

Hardware Reset

A factory reset will erase all links stored in the device’s database as well as

any customized properties.

Hardware Reset

La page charge ...

INSTEON Refurbished Remote Control Plug-In Lamp Dimmer Module Manuel utilisateur

Ce manuel convient également à

INSTEON Refurbished Remote Control Plug-In Lamp Dimmer Module Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents