Mitsubishi Electric PLA-A12EA7 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: PLA-A12EA7

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Ce manuel convient également à

SPLIT-SYSTEM HEAT PUMP

PLA-A

EA7

MANUEL D’UTILISATION

Pour une utilisation correcte sans risques, veuillez lire le manuel d’utilisation en entier avant de vous servir du

climatiseur.

OPERATION MANUAL

For safe and correct use, please read this operation manual thoroughly before operating the air-conditioner unit.

MANUAL DE INSTRUCCIONES

Lea este manual de instrucciones hasta el nal antes de poner en marcha la unidad de aire acondicionado para

garantizar un uso seguro y correcto.

POUR L’UTILISATEUR

FOR USER

PARA EL USUARIO

English

Français

Español

BH79D659H01_EN.indd 1 8/5/2016 11:07:21 AM

Contents

1. Safety Precautions .................................2

2. Parts Names ......................................3

3. Operation ........................................7

4. Timer ...........................................13

1. Safety Precautions

►Beforeinstallingtheunit,makesureyoureadallthe“Safety

Precautions”.

►The “Safety Precautions” provide very important points re-

gardingsafety.Makesureyoufollowthem.

►Pleasereporttoortakeconsentbythesupplyauthoritybefore

connectiontothesystem.

Symbolsusedinthetext

Warning:

Describesprecautionsthatshouldbeobservedtopreventdangerof

injuryordeathtotheuser.

Caution:

Describesprecautionsthatshouldbeobservedtopreventdamage

to the unit.

Symbolsusedintheillustrations

: Indicates a part which must be grounded.

Caution:

• Donotuseanysharpobjecttopushthebuttons,asthismaydam-

agetheremotecontroller.

• 

Neverblockorcovertheindoororoutdoorunit’sintakesoroutlets.

Disposing of the unit

When you need to dispose of the unit, consult your dealer.

Warning:

• Thereappliancesarenotaccessibletothegeneralpublic.

• Theunitmustnotbeinstalledbytheuser.Askthedealeroran

authorizedcompanytoinstalltheunit.Iftheunitisinstalledim-

properly,waterleakage,electricshockorremayresult.

• Donotstandon,orplaceanyitemsontheunit.

• Donotsplashwaterovertheunitanddonottouchtheunitwith

wethands.Anelectricshockmayresult.

• Donotspraycombustiblegasclosetotheunit.Firemayresult.

• Donotplaceagasheateroranyotheropen-ameappliancewhere

itwillbeexposedtotheairdischargedfromtheunit.Incomplete

combustionmayresult.

• Donotremovethefrontpanelorthefanguardfromtheoutdoor

unitwhenitisrunning.

• Whenyounoticeexceptionallyabnormalnoiseorvibration,stop

operation,turnoffthepowerswitch,andcontactyourdealer.

• Neverinsertngers,sticksetc.intotheintakesoroutlets.

• Ifyoudetectoddsmells,stopusingtheunit,turnoffthepower

switchandconsultyourdealer.Otherwise,abreakdown,electric

shockorremayresult.

• ThisairconditionerisNOTintendedforusebychildrenorinrm

personswithoutsupervision.

• Youngchildrenmustbesupervisedtoensurethattheydonotplay

withtheairconditioner.

• Iftherefrigerationgasblowsoutorleaks,stoptheoperationofthe

airconditioner,thoroughlyventilatetheroom,andcontactyour

dealer.

• Thisapplianceisintendedtobeusedbyexpertortrainedusersin

shops,inlightindustryandonfarms,orforcommercialusebylay

persons.

• Thisappliancecan be used by children aged from 8 years and

aboveandpersonswithreducedphysical,sensoryormentalca-

pabilitiesorlackofexperienceandknowledgeiftheyhavebeen

givensupervisionorinstructionconcerninguseoftheappliance

inasafewayandunderstandthehazardsinvolved.Childrenshall

notplaywiththeappliance.Cleaningandusermaintenanceshall

notbemadebychildrenwithoutsupervision.

• Thisapplianceisnotintendedforusebypersons(includingchil-

dren) with reduced physical, sensory or mental capabilities, or

lackofexperienceandknowledge,unlesstheyhavebeengiven

supervisionorinstructionconcerninguseoftheappliancebya

personresponsiblefortheirsafety.

• Childrenshouldbesupervisedtoensurethattheydonotplaywith

the appliances.

• Wheninstallingorrelocating,orservicingtheairconditioner,use

only the specied refrigerant (R410A) to charge the refrigerant

lines.Donotmixitwithanyotherrefrigerantanddonotallowair

toremaininthelines.

 Ifairismixedwiththerefrigerant,thenitcanbethecauseofab-

normalhighpressureintherefrigerantline,andmayresultinan

explosionandotherhazards.

 Theuseofanyrefrigerantotherthanthatspeciedforthesystem

willcausemechanicalfailureorsystemmalfunctionorunitbreak-

down.Intheworstcase,thiscouldleadtoaseriousimpediment

tosecuringproductsafety.

5. Emergency Operation for Wireless Remote-controller .....13

6. Care and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

7. Trouble Shooting ..................................15

8. Specications ....................................16

Note:

Thephrase“Wiredremotecontroller”inthisoperationmanualrefersonlytothePAR-32MAA.(Ifyouneedanyinformationforthe

otherremotecontroller,pleaserefertotheinstructionbookincludedineachremotecontroller.)

BH79D659H01_EN.indd 2 8/5/2016 11:07:22 AM

2.PartsNames

■

IndoorUnit

PLA-A·EA7

Fan steps 4 steps

Vane Auto with swing

Louver –

Filter Long-life

Filter cleaning indication 2,500 hr

Enter the model setting number for

the indoor unit you want to operate.

001

Air outlet

Filter

Air intake

Vane

Wired remote controller IR wireless remote controller

COOL

DRY

AUTO

FAN

HEAT

COOL

DRY

AUTO

FAN

HEAT

Remotecontroller(Optionalparts)

BH79D659H01_EN.indd 3 8/5/2016 11:07:22 AM

2.PartsNames

■

WiredRemoteController

Function buttons

4 3 2 1

7 8 9 0

The functions of the function buttons change depending on the

screen.

Refertothebuttonfunctionguidethatappearsatthebottomofthe

LCDforthefunctionstheyserveonagivenscreen.

Whenthesystemiscentrallycontrolled,thebuttonfunctionguide

thatcorrespondstothelockedbuttonwillnotappear.

Fri

Room

Set temp.

Mode Temp. Fan

Cool Auto

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

Maindisplay Mainmenu

Functionguide

▌1[ON/OFF]button

Press to turn ON/OFF the indoor unit.

▌2[SELECT]button

Press to save the setting.

▌3[RETURN]button

Press to return to the previous screen.

▌4[MENU]button

Press to bring up the Main menu.

▌5BacklitLCD

Operation settings will appear.

When the backlight is off, pressing any button turns the backlight on

and it will stay lit for a certain period of time depending on the screen.

When the backlight is off, pressing any button turns the backlight on

and does not perform its function. (except for the [ON/OFF] button)

▌6ON/OFFlamp

This lamp lights up in green while the unit is in operation. It blinks while

the remote controller is starting up or when there is an error.

▌7Functionbutton[F1]

Main display: Press to change the operation mode.

Main menu: Press to move the cursor down.

▌8Functionbutton[F2]

Main display: Press to decrease temperature.

Main menu: Press to move the cursor up.

▌9Functionbutton[F3]

Main display: Press to increase temperature.

Main menu: Press to go to the previous page.

▌0Functionbutton[F4]

Main display: Press to change the fan speed.

Main menu: Press to go to the next page.

Controller interface

7 8 9 0 7 8 9 0

BH79D659H01_EN.indd 4 8/5/2016 11:07:22 AM

2.PartsNames

The main display can be displayed in two different modes: “Full” and “Basic”. The factory setting is “Full”. To switch to the “Basic” mode, change the

setting on the Main display setting. (Refer to operation manual included with remote controller.)

▌1Operationmode

Indoor unit operation mode appears here.

▌2Presettemperature

Preset temperature appears here.

▌3Clock(SeetheInstallationManual.)

Current time appears here.

▌4Fanspeed

Fan speed setting appears here.

▌5Buttonfunctionguide

Functions of the corresponding buttons appear here.

▌6

Appears when the ON/OFF operation is centrally controlled.

▌7

Appears when the operation mode is centrally controlled.

▌8

Appears when the preset temperature is centrally controlled.

▌9

Appears when the lter reset function is centrally controlled.

▌0

Indicates when lter needs maintenance.

▌1Roomtemperature(SeetheInstallationManual.)

Current room temperature appears here.

▌2

Appears when the buttons are locked.

* All icons are displayed for explanation.

Fri

Mode Temp. Fan

Room

Cool

Set temp.

Fri

Cool

Mode Temp. Fan

Set temp.

)

2 3 4 5 6 8 9

▌3

Appears when the On/Off timer, Night setback, or Auto-off timer func-

tion is enabled.

appears when the timer is disabled by the centralized control

system.

▌4

Appears when the Weekly timer is enabled.

▌5

Appears while the units are operated in the energy-save mode. (Will

not appear on some models of indoor units)

▌6

Appears while the outdoor units are operated in the silent mode.

▌7

Appears when the built-in thermistor on the remote controller is acti-

vated to monitor the room temperature (1).

appears when the thermistor on the indoor unit is activated to

monitor the room temperature.

▌8

Appears when the units are operated in the energy-save mode with 3D

i-see Sensor.

▌9

Indicates the vane setting.

▌)

Indicates the louver setting.

(This indication is not available for this model.)

▌!

Indicates the ventilation setting.

▌@

Appears when the preset temperature range is restricted.

Most settings (except ON/OFF, mode, fan speed, temperature) can be made from the Menu screen.

(Refer to operation manual included with remote controller.)

Display

BH79D659H01_EN.indd 5 8/5/2016 11:07:22 AM

2.PartsNames

■WirelessRemote-Controller

■

WirelessRemote-Controller

Note(Onlyforwirelessremotecontroller):

■

When using the wireless remote controller, point it towards the receiver on the indoor unit.

■

If the remote controller is operated within approximately 2 minutes after power is supplied to the

indoor unit, the indoor unit may beep twice as the unit is performing the initial automatic check.

■

The indoor unit beeps to conrm that the signal transmitted from the remote controller has been

received. Signals can be received up to approximately 7 meters, 275-19/32 inch in a direct line

from the indoor unit in an area 45° to the left and right of the unit. However, illumination such as

uorescent lights and strong light can affect the ability of the indoor unit to receive signals.

■

If the operation lamp near the receiver on the indoor unit is blinking, the unit needs to be in-

spected. Consult your dealer for service.

■

Handle the remote controller carefully! Do not drop the remote controller or subject it to strong

shocks. In addition, do not get the remote controller wet or leave it in a location with high humid-

ity.

■

To avoid misplacing the remote controller, install the holder included with the remote controller on

a wall and be sure to always place the remote controller in the holder after use.

Batteryinstallation/replacement

1. Remove the top cover, insert 2 AAA batter-

ies, and then install the top cover.

2. Press the Reset button.

■

Outdoorunit

Two AAA batteries

Insert the negative (–)

end of each battery rst.

Install the batteries in

the correct directions

(+, –) !

Press the Reset button

with an object that has a

narrow end.

Top cover

* For explanation purposes, all of the items

that appear in the display are shown.

* All items are displayed when the Reset but-

ton is pressed.

Transmission indicator

Timer indicator

Remote controller display

ON/OFF button

Set Temperature buttons

Fan Speed button (Changes fan speed)

Airow button (Changes up/down airow direction)

Mode button (Changes operation mode)

Check button

Test Run button

Transmission area

Operation areas

Timer Off button

Timer On button

Hour button

Minute button

Set Time button (Sets the time)

Louver button (Changes left/right airow direction)

Reset button

Power

Earth

Service Panel

Indoor-Outdoor

Connection wire

Ref. Pipes

BH79D659H01_EN.indd 6 8/5/2016 11:07:23 AM

3.Operation

■

Abouttheoperationmethod,refertotheoperationmanualthatcomeswitheachremotecontroller.

3.1.TurningON/OFF

[ON] [OFF]

Press the [ON/OFF] button.

The ON/OFF lamp will light up in green,

and the operation will start.

Press the [ON/OFF] button again.

The ON/OFF lamp will come off, and

the operation will stop.

■

Operationstatusmemory

Remote controller setting

Operation mode Operation mode before the power was turned off

Preset temperature Preset temperature before the power was turned off

Fan speed Fan speed before the power was turned off

■

Settablepresettemperaturerange

Operation mode Preset temperature range

Cool/Dry 67 - 87 ºF/19 - 30 ºC

Heat 63 - 83 ºF/17 - 28 ºC

Auto 67 - 83 ºF/19 - 28 ºC

Fan/Ventilation Not settable

Note:

EvenifyoupresstheON/OFFbuttonimmediatelyaftershuttingdowntheoperationisprogress,theairconditionerwillnotstartforabout3minutes.

Thisistopreventtheinternalcomponentsfrombeingdamaged.

3.2.ModeSelection

Press the [F1] button to go through the op-

eration modes in the order of “Cool”, “Dry”,

“Fan”, “Auto”, and “Heat”. Select the desired

operation mode.

Cool Dry Fan

Auto Heat

• Operation modes that are not available to

the connected outdoor unit models will not

appear on the display.

Whattheblinkingmodeiconmeans

The mode icon will blink when other indoor units in the same refrigerant

system (connected to the same outdoor unit) are already operated in a

different mode. In this case, the rest of the unit in the same group can

only be operated in the same mode.

Automaticoperation

■

According to a set temperature, cooling operation starts if the room tem-

perature is too hot and heating operation starts if the room temperature

is too cold.

■

During automatic operation, if the room temperature changes and re-

mains 2.0 °C, 4 °F or more above the set temperature for 15 minutes,

the air conditioner switches to cool mode. In the same way, if the room

temperature remains 2.0 °C, 4 °F or more below the set temperature for

15 minutes, the air conditioner switches to heat mode.

F1 F2 F3 F4

Cool

Room

AutoSet temp.

Mode Temp. Fan

Fri

Informationformultisystemairconditioner(Outdoor

unit:MXZseries)

■

Multisystemairconditioner(Outdoorunit:MXZseries)can

connecttwoormoreindoorunitswithoneoutdoorunit.According

tothecapacity,2ormoreunitscanoperatesimultaneously.

• When you try to operate 2 or more indoor units with 1 outdoor unit

simultaneously, one for the cooling and the other for heating, the

operation mode of the indoor unit that operates earlier is selected.

The other indoor units that will start the operation later cannot operate,

indicating an operation state in blinking.

In this case, please set all the indoor units to the same operation

mode.

• There might be a case that the indoor unit, which is operating in “Auto”

mode. Cannot change over to the operating mode “Cool”/“Heat” and

becomes a state of standby.

• When indoor unit starts the operation while the defrosting of outdoor

unit is being done, it takes a few minutes (max. about 15 minutes) to

blow out the warm air.

• In the heating operation, though indoor unit that does not operate may

get warm or the sound of refrigerant owing may be heard, they are

not malfunction. The reason is that the refrigerant continuously ows

into it.

3.3.Temperaturesetting

<Cool,Dry,Heat,andAuto>

Cool

Room

AutoSet temp.

Mode Temp. Fan

Fri

Example display

(Centigrade in 0.5-degree increments)

F1 F2 F3 F4

Cool

Room

AutoSet temp.

Mode Temp. Fan

Fri

Press the [F2] button to decrease the preset temperature, and press the

[F3] button to increase.

• Refer to the table on page 7 for the settable temperature range for dif-

ferent operation modes.

• Preset temperature range cannot be set for Fan/Ventilation operation.

• Preset temperature will be displayed either in Centigrade in 0.5- or

1-degree increments, or in Fahrenheit, depending on the indoor unit

model and the display mode setting on the remote controller.

Cool mode

15 minutes (switches from

heating to cooling)

Set temperature +2.0 °C, +4 °F

Set temperature

Set temperature -2.0 °C, -4 °F

15 minutes (switches from

cooling to heating)

BH79D659H01_EN.indd 7 8/5/2016 11:07:23 AM

3.Operation

3.4.Fanspeedsetting

F1 F2 F3 F4

Cool

Room

Set temp.

Mode Temp. Fan

Fri

Press the [F4] button to go through the fan speeds in the following order.

Auto

• The available fan speeds depend on the models of connected indoor

units.

Notes:

●

Thenumberofavailablefanspeedsdependsonthetypeofunit

connected.

● Inthefollowingcases,theactualfanspeedgeneratedbytheunit

willdifferfromthespeedshowntheremotecontrollerdisplay.

 1.Whilethedisplayisin“STANDBY”or“DEFROST”states.

 2.Whenthetemperatureoftheheatexchangerislowintheheat-

ingmode.

  (e.g.immediatelyafterheatingoperationstarts)

 3InHEATmode,whenroomtemperatureishigherthanthetem-

perature setting.

 4.WhentheunitisinDRYmode.

3.5.Airowdirectionsetting

3.5.1NavigatingthroughtheMainmenu

<AccessingtheMainmenu>

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

<Itemselection>

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

Cursor

Press the [MENU] button.

The Main menu will appear.

Press [F1] to move the cursor down.

Press [F2] to move the cursor up.

<Navigatingthroughthepages>

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

page

<Savingthesettings>

F1 F2 F3 F4

OU silent mode

Mon Tue Wed Thu Fri Sat Sun

Start Stop Silent

Setting display:

day

<ExitingtheMainmenuscreen>

F1 F2 F3 F4

Cool

Room

Set temp.

Mode Temp. Fan

Fri

If no buttons are touched for 10 minutes, the screen will automatically

return to the Main display. Any settings that have not been saved will

be lost.

<Displayofunsupportedfunctions>

F1 F2 F3 F4

Title

Not available

Unsupported function

Return:

Press [F3] to go to the previous page.

Press [F4] to go to the next page.

Select the desired item, and press

the [SELECT] button.

The screen to set the selected item

will appear.

Press the [RETURN] button to exit

the Main menu and return to the

Main display.

The message at left will appear

if the user selects a function not

supported by the corresponding

indoor unit model.

BH79D659H01_EN.indd 8 8/5/2016 11:07:23 AM

Outlet No. 2

Outlet No. 3

Outlet No. 1

Outlet No. 4

3.Operation

3.5.2Vane·Vent.(Lossnay)

<Accessingthemenu>

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

<Vanesetting>

F1 F2 F3 F4

Fri

Swing Off

LouverVent.Vane

<Vent.setting>

F1 F2 F3 F4

Fri

Low

Vent.

<ReturningtotheMainmenu>

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode

Select “Vane·Louver·Vent.

(Lossnay)” from the Main menu

(refer to page 8), and press the

[SELECT] button.

Press the [F1] or [F2] button to go

through the vane setting options:

“Step 1”, “Step 2”, “Step 3”, “Step

4”, “Step 5”, “Swing” and “Auto”.

Select the desired setting.

Swing

Auto

Select “Swing” to move the vanes

up and down automatically.

When set to “Step 1” through “Step

5”, the vane will be xed at the

selected angle.

Press the [F3] button to go through

the ventilation setting options in the

order of “Off”, “Low”, and “High”.

* Settable only when LOSSNAY

unit is connected.

Off Low High

• The fan on some models of indoor

units may be interlocked with

certain models of ventilation units.

Press the [RETURN] button to go

back to the Main menu.

Remote controller setting

The airow direction of this outlet

is controlled by the airow direc-

tion setting of remote controller.

Fixed

The airow direction of this outlet is xed

in particular direction.

* When it is cold because of direct

airow, the airow direction can be

xed horizontally to avoid direct airow.

<Howtosetthexedup/downairdirection>

Note:

● Thisfunctioncannotbesetdependingontheoutdoorunittobe

connected.

• For PLA-A·EA7, only the particular outlet can be xed to certain

direction with the procedures below. Once xed, only the set outlet is

xed every time air conditioner is turned on. (Other outlets follow UP/

DOWN air direction setting of remote controller.)

■

Explanationofword

• “Refrigerant address No.” and “Unit No.” are the numbers given to

each air conditioner.

• “Outlet No.” is the number given to each outlet of air conditioner.

(Refer to the illustration below.)

• “Up/Down air direction” is the direction (angle) to x.

Step 1

Step 4

Auto

Step 2

Step 5

Step 3

Swing

Notes:

●

Duringswingoperation,thedirectionalindicationonthescreen

doesnotchangeinsyncwiththedirectionalvanesontheunit.

● Availabledirectionsdependonthetypeofunitconnected.

●

Inthefollowingcases,theactualairdirectionwilldifferfromthe

directionindicatedontheremotecontrollerdisplay.

1.Whilethedisplayisin“STANDBY”or“DEFROST”states.

2.Immediatelyafterstartingheatmode(whilethesystemiswait-

ingforthemodechangetotakeeffect).

3.Inheatmode,whenroomtemperatureishigherthanthetem-

perature setting.

Horizontal airow

Note:

TheoutletNo.isindicatedbythenumberofgroovesonboth

endsofeachairoutlet.Settheairdirectionwhilecheckingthe

informationshownontheremotecontrollerdisplay.

Air outlet identication marks

BH79D659H01_EN.indd 9 8/5/2016 11:07:24 AM

3.Operation3.Operation

■

Manualvaneangle(Wiredremotecontroller)

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Maintenance

Initial setting

Service

F1 F2 F3 F4

Maintenance menu

Main menu:

Cursor

Auto descending panel

Manual vane angle

3D i-See sensor

F1 F2 F3 F4

Manual vane angle

Input display:

Cur. Address Check

Ref. address

Unit No.

Identify unit Check button

F1 F2 F3 F4

Manual vane angle

Select:

Setting

Outlet Angle

Note:

Donotsetthedraftreductioninanenvironmentwithhighhumidity.

Otherwise,condensationmayformanddrip.

1 Select “Maintenance” from the

Main menu (refer to page 8), and

press the [SELECT] button.

2 Select “Manual vane angle” with

the [F1] or [F2] button, and press

the [SELECT] button.

3 Move the cursor to “Ref. address”

or “Unit No.” with the [F1] button

to select.

Select the refrigerant address

and the unit number for the units

to whose vanes are to be xed,

with the [F2] or [F3] button, and

press the [SELECT] button.

• Ref. address: Refrigerant ad-

dress

• Unit No.: 1, 2, 3, 4

Press the [F4] button to conrm

the unit.

The vane of only the target

indoor unit is pointing downward.

4 The current vane setting will ap-

pear.

Select the desired outlets from

1 through 4 with the [F1] or [F2]

button.

• Outlet: “1”, “2”, “3”, “4” and “1, 2,

3, 4, (all outlets)”

Press the [F3] or [F4] button to

go through the option in the order

of “No setting (reset)”, “Step 1”,

“Step 2”, “Step 3”, “Step 4”, “Step

5” and “Draft reduction*”.

Select the desired setting.

* Draft reduction

The airow direction for this set-

ting is more horizontal than the

airow direction for the “Step 1”

setting in order to reduce a drafty

feeling. The draft reduction can

be set for only 1 vane.

■

Vanesetting

Press the [SELECT] button to save the settings.

A screen will appear that indicates the setting information is being trans-

mitted.

The setting changes will be made to the selected outlet.

The screen will automatically return to the one shown above (step 5)

when the transmission is completed.

Make the settings for other outlets, following the same procedures.

Ifalloutletsareselected,

willbedisplayedthenexttime

the unit goes into operation.

Navigating through the screens

• To go back to the Main menu ................ [MENU] button

• To return to the previous screen .......... [RETURN] button

Step 1 Step 2

Step 3

No setting

Draft

reduction*

All outlets

Step 5Step 4

BH79D659H01_EN.indd 10 8/5/2016 11:07:24 AM

Vane setting

Direct Indirect

Cooling

horizontal → swing keep horizontal

Heating

keep downward downward → horizontal

F1 F2 F3 F4

3D i-See sensor

Cursor

Setting display:

Air distribution

Energy saving option

Seasonal airflow

3.6.2 Airdistribution

F1 F2 F3 F4

Air distribution

Input display:

Cur. Address Check

Ref. address

Unit No.

Identify unit Check button

F1 F2 F3 F4

Air distribution

Select:

Cur.

Ref. address

Unit No.

Auto vane

Direct/Indirect setting

All

Direct/Indirect

3 Select the desired menu with the

[F1] or [F2] button, and press the

[SELECT] button.

• Air distribution

Select the airow direction control

method when the airow direction

is set to “Auto”.

• Energy saving option

Operates the energy-save mode

according to whether persons are

detected in the room by the 3D

i-see Sensor.

• Seasonal airow

When the thermostat turns off, the

fan and the vanes operate accord-

ing to the control settings.

1 Move the cursor to “Ref. address”

or “Unit No.” with the [F1] button to

select.

Select the refrigerant address and

the unit number for the units to

whose vanes are to be xed, with

the [F2] or [F3] button, and press

the [SELECT] button.

• Ref. address: Refrigerant address

• Unit No.: 1, 2, 3, 4

Press the [F4] button to conrm

the unit.

The vane of only the target indoor

unit is pointing downward.

2 Select the menu with the [F4] but-

ton.

Default → Area → Direct/Indirect

→ Default…

Default: The vanes move the

same as during normal operation.

“Area”*: The vanes move to the

down airow direction toward

areas with a high oor tempera-

ture during Cool mode and toward

areas with a low oor temperature

during Heat mode. Otherwise,

the vanes move to the horizontal

airow direction.

“Direct/Indirect”*: The vanes

automatically move relative to the

areas where persons are detect-

ed.

The vanes operate as indicated in

the following table.

* In order to enable this function,

the airow direction must be set to

“Auto”.

3.Operation

1 First, conrm by setting “Ref.

address” to 0 and “Unit No.” to 1.

• Move the cursor to “Ref. address”

or “Unit No.” with the [F1] button to

select.

• Select the refrigerant address and

the unit number for the units to

whose vanes are to be xed, with

the [F2] or [F3] button, and press

the [SELECT] button.

• Ref. address: Refrigerant address

• Unit No.: 1, 2, 3, 4

Press the [F4] button to conrm

the unit.

2 Change the “Unit No.” in order and

check each unit.

• Press the [F1] button to select

“Unit No.”.

Press the [F2] or [F3] button to

change the “Unit No.” to the unit

that you want to check, and then

press the [F4] button.

• After pressing the [F4] button, wait

approximately 15 seconds, and

then check the current state of the

air conditioner.

→ The vane is pointing downward.

→ This air conditioner is displayed

on the remote controller.

→ All outlets are closed. →

Press

the [RETURN] button and continue

the operation from the beginning.

→ The messages shown to the

left are displayed. → The target

device does not exist at this refrig-

erant address.

• Press the [RETURN] button to

return to the initial screen.

3 Change the “Ref. address” to the

next number.

• Refer to step 1 to change the

“Ref. address” and continue with

the conrmation.

3.6.3Di-seeSensorsetting

Note:

● Thisfunctioncannotbesetdependingontheoutdoorunittobe

connected.

3.6.1 3Di-seeSensorsetting

F1 F2 F3 F4

Manual vane angle

Input display:

Cur. Address Check

Ref. address

Unit No.

Identify unit Check button

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Maintenance

Initial setting

Service

F1 F2 F3 F4

Maintenance menu

Main menu:

Cursor

Auto descending panel

Manual vane angle

3D i-See sensor

■ Conrmationprocedure(wiredremotecontroller)

F1 F2 F3 F4

Manual vane angle

Return:

Ref. address

Unit No.

Function setting for unit

with vane fully open.

F1 F2 F3 F4

Manual vane angle

Return:

No communication

Check Unit state.

1 Select “Maintenance” from the

Main menu (refer to page 8), and

press the [SELECT] button.

2 Select “3D i-See sensor” with the

[F1] or [F2] button, and press the

[SELECT] button.

BH79D659H01_EN.indd 11 8/5/2016 11:07:24 AM

3.Operation

F1 F2 F3 F4

Direct/Indirect setting

: Direct

: Indirect

: Direct

Select:

Outlet

Angle

3 When Direct/Indirect is selected,

set each air outlet.

Select the air outlet with the [F1]

or [F2] button, and change the set-

ting with the [F4] button.

After changing the settings for all

of the air outlets, press the [SE-

LECT] button to save the settings.

3.6.3 Energysavingoption

F1 F2 F3 F4

Energy saving option

Cursor

Setting display:

No occupancy energy save

Room occupancy energy save

No occupancy Auto-OFF

1 Select the desired menu with the

[F1] or [F2] button.

No occupancy energy save

If there are no persons in the room

for 60 minutes or more, energy-

saving operation equal to 2 °C, 4

°F is performed.

Room occupancy energy save

If the occupancy rate decreases

to approximately 30% of the

maximum occupancy rate, energy-

saving operation equal to 1 °C, 2

°F is performed.

No occupancy Auto-OFF

If there are no persons in the

room for the set amount of time

(60–180 minutes), the operation is

automatically stopped.

2 When No occupancy energy save

or Room occupancy energy save

is selected.

Select the setting with the [F4] but-

ton.

OFF → Cooling only → Heating

only → Cooling/Heating → OFF…

After changing the setting, press

the [SELECT] button to save the

setting.

OFF: The function is disabled.

Cooling only: The function is ena-

bled only during Cool mode.

Heating only: The function is ena-

bled only during Heat mode.

Cooling/Heating: The function is

enabled during both Cool mode

and Heat mode.

3 When No occupancy Auto-OFF is

selected.

Set the time with the [F3] or [F4]

button.

---: The setting is disabled (the op-

eration will not stop automatically).

60–180: The time can be set in

10-minute increments.

4 The message at left will appear

if the operation was stopped

automatically by the No occupancy

Auto-OFF setting.

F1 F2 F3 F4

Energy saving option

Select:

No occupancy energy save

Cooling/Heating

F1 F2 F3 F4

Energy saving option

Select:

Room occupancy energy save

Cooling/Heating

F1 F2 F3 F4

Energy saving option

Select:

Time

No occupancy Auto-OFF

120 min.

F1 F2 F3 F4

18:47 Thu

Shut down by

No Occupancy Auto-OFF

31/Dec AM12:59

BH79D659H01_EN.indd 12 8/5/2016 11:07:25 AM

4.Timer

■ Timer functions are different by each remote controller.

■ For details on how to operate the remote controller, refer to the appropriate operation manual included with each remote controller.

Notes:

Anypersonatthefollowingplacescannotbedetected.

● Alongthewallonwhichtheairconditionerisinstalled

● Directlyundertheairconditioner

● Whereanyobstacle,suchasfurniture,isbetweenthepersonand

theairconditioner

Apersonmaynotbedetectedinthefollowingsituations.

● Roomtemperatureishigh.

● Apersonwearsheavyclothesandhis/herskinisnotexposed.

● Aheatingelementofwhichtemperaturechangessignicantlyis

present.

● Someheatsources,suchasasmallchildorpet,maynotbe

sensed.

● Aheatsourcedoesnotmoveforalongtime.

The3Di-seeSensoroperatesonceapproximatelyevery3minutes

tomeasuretheoortemperatureanddetectpersonsintheroom.

● Theintermittentoperatingsoundisanormalsoundproduced

whenthe3Di-seeSensorismoving.

3.7.Ventilation

For LOSSNAY combination

■ The following 2 patterns of operation is available.

• Run the ventilator together with indoor unit.

• Run the ventilator independently.

Notes:(forwirelessremotecontroller)

● Runningtheventilatorindependentlyisnotavailable.

● Noindicationontheremotecontroller.

3.Operation

1 Select the setting with the [F4]

button.

OFF → Cooling only → Heating

only → Cooling/Heating → OFF…

After changing the setting, press

the [SELECT] button to save the

setting.

OFF: The function is disabled.

Cooling only: When the thermostat

turns off during Cool mode, the

vanes move up and down.

Heating only: When the thermo-

stat turns off during Heat mode,

the vanes move to the horizontal

airow direction to circulate the air.

Cooling/Heating: The function is

enabled during both Cool mode

and Heat mode.

* In order to enable this function,

the airow direction must be set to

“Auto”.

3.6.4 Seasonalairowfunction

F1 F2 F3 F4

Seasonal airflow

Select:

Seasonal airflow

Cooling/Heating

Whentheremotecontrollercannotbeused

When the batteries of the remote controller run out or the remote

controller malfunctions, the emergency operation can be done using the

emergency buttons on the grille.

DEFROST/STAND BY lamp

Operation lamp

Emergency operation cooling switch

Emergency operation heating switch

Receiver

Starting operation

• To operate the cooling mode, press the

button

for more than 2

seconds.

• To operate the heating mode, press the button

for more than 2

seconds.

• Lighting of the Operation lamp

means the start of operation.

Notes:

Detailsofemergencymodeareasshownbelow.

Details of EMERGENCY MODE are as shown below.

Operation mode COOL HEAT

Set temperature 24°C, 75°F 24°C, 75°F

Fan speed High High

Airow direction Horizontal Downward

Stopping operation

• To stop operation, press the

button C or the button D for more than

2 seconds.

5.EmergencyOperationforWirelessRemote-controller

C B

B A

BH79D659H01_EN.indd 13 8/5/2016 11:07:25 AM

6.CareandCleaning

■ Filterinformation■ Filterinformation

Cool

Room

AutoSet temp.

Mode Temp. Fan

Fri

will appear on the Main display

in the Full mode when it is time to

clean the lters.

Wash,clean,orreplacethelters

whenthissignappears.

Refer to the indoor unit Instruc-

tionsManualfordetails.

F1 F2 F3 F4

Main

Main display:

Cursor Page

Main menu

Restriction

Energy saving

Night setback

Filter information

Error information

Select “Filter information” from the

Main menu (refer to page 8), and

press the [SELECT] button.

F1 F2 F3 F4

Main menu:

Filter information

Reset

Please clean the filter.

Press Reset button after

filter cleaning.

Press the [F4] button to reset lter

sign.

Refer to the indoor unit Instructions

Manual for how to clean the lter.

F1 F2 F3 F4

Filter information

Cancel

Reset filter sign?

Filter sign reset

Main menu:

Select “OK” with the [F4] button.

A conrmation screen will appear.

Navigating through the screens

• To go back to the Main menu

....................... [MENU] button

• To return to the previous screen

....................... [RETURN] button

Cool

Room

AutoSet temp.

Mode Temp. Fan

Fri

When the is displayed on the

Main display in the Full mode, the

system is centrally controlled and

the lter sign cannot be reset.

If two or more indoor units are connected, lter cleaning timing for each

unit may be different, depending on the lter type.

The icon

will appear when the lter on the main unit is due for

cleaning.

When the lter sign is reset, the cumulative operation time of all units

will be reset.

The icon

is scheduled to appear after a certain duration of operation,

based on the premise that the indoor units are installed in a space with

ordinary air quality. Depending on the air quality, the lter may require

more frequent cleaning.

The cumulative time at which lter needs cleaning depends on the model.

• This indication is not available for wireless remote controller.

Caution:

• Askauthorizedpeopletocleanthelter.

■ Cleaning the filters

• Clean the lters using a vacuum cleaner. If you do not have a vacuum

cleaner, tap the lters against a solid object to knock off dirt and dust.

• If the lters are especially dirty, wash them in lukewarm water. Take care

to rinse off any detergent thoroughly and allow the lters to dry completely

before putting them back into the unit.

Caution:

• Donotdrytheltersindirectsunlightorbyusingaheatsource,

suchasanelectricheater:thismaywarpthem.

• Donotwashtheltersinhotwater(above50°C,122°F),asthis

maywarpthem.

• Makesurethattheairltersarealwaysinstalled.Operatingthe

unitwithoutairlterscancausemalfunction.

Caution:

• Beforeyoustartcleaning,stopoperationandturnOFFthepower

supply.

• Indoorunitsareequippedwithlterstoremovethedustofsucked-

inair.Cleantheltersusingthemethodsshowninthefollowing

sketches.

BH79D659H01_EN.indd 14 8/5/2016 11:07:25 AM

7.TroubleShooting

Having trouble? Here is the solution. (Unit is operating normally.)

Air conditioner does not heat or cool well.

■ Clean the lter. (Airow is reduced when the lter is dirty or clogged.)

■ Check the temperature adjustment and adjust the set temperature.

■ Make sure that there is plenty of space around the outdoor unit. Is the

indoor unit air intake or outlet blocked?

■ Has a door or window been left open?

When heating operation starts, warm air does not blow from the indoor

unit soon.

■ Warm air does not blow until the indoor unit has sufciently warmed

up.

During Heat mode, the air conditioner stops before the set room tem-

perature is reached.

■ When the outdoor temperature is low and the humidity is high, frost

may form on the outdoor unit. If this occurs, the outdoor unit performs

a defrosting operation. Normal operation should begin after approxi-

mately 10 minutes.

Airow direction changes during operation or airow direction cannot be

set.

■ During Heat mode, the vanes automatically move to the horizontal air-

ow direction when the airow temperature is low or during defrosting

mode.

When the airow direction is changed, the vanes always move up and

down past the set position before nally stopping at the position.

■ When the airow direction is changed, the vanes move to the set posi-

tion after detecting the base position.

A owing water sound or occasional hissing sound is heard.

■ These sounds can be heard when refrigerant is owing in the air

conditioner or when the refrigerant ow is changing.

A cracking or creaking sound is heard.

■ These sounds can be heard when parts rub against each due to

expansion and contraction from temperature changes.

The room has an unpleasant odor.

■ The indoor unit draws in air that contains gases produced from the

walls, carpeting, and furniture as well as odors trapped in clothing,

and then blows this air back into the room.

A white mist or vapor is emitted from the indoor unit.

■ If the indoor temperature and the humidity are high, this condition may

occur when operation starts.

■ During defrosting mode, cool airow may blow down and appear like a

mist.

Water or vapor is emitted from the outdoor unit.

■ During Cool mode, water may form and drip from the cool pipes and

joints.

■ During Heat mode, water may form and drip from the heat exchanger.

■ During defrosting mode, water on the heat exchanger evaporates and

water vapor may be emitted.

“

” appears in the remote controller display. ■ During central control, “ ” appears in the remote controller display

and air conditioner operation cannot be started or stopped using the

remote controller.

When restarting the air conditioner soon after stopping it, it does not

operate even though the ON/OFF button is pressed.

■ Wait approximately three minutes.

(Operation has stopped to protect the air conditioner.)

Air conditioner operates without the ON/OFF button being pressed.

■ Is the on timer set?

Press the ON/OFF button to stop operation.

■ Is the air conditioner connected to a central remote controller?

Consult the concerned people who control the air conditioner.

■ Does “

” appear in the remote controller display?

Consult the concerned people who control the air conditioner.

■ Has the auto recovery feature from power failures been set?

Press the ON/OFF button to stop operation.

Air conditioner stops without the ON/OFF button being pressed.

■ Is the off timer set?

Press the ON/OFF button to restart operation.

■ Is the air conditioner connected to a central remote controller?

Consult the concerned people who control the air conditioner.

■ Does “

” appear in the remote controller display?

Consult the concerned people who control the air conditioner.

Remote controller timer operation cannot be set.

■ Are timer settings invalid?

If the timer can be set,

or appears in the remote controller

display.

“PLEASE WAIT” appears in the remote controller display.

■ The initial settings are being performed. Wait approximately 3 min-

utes.

An error code appears in the remote controller display.

■ The protection devices have operated to protect the air conditioner.

■ Do not attempt to repair this equipment by yourself.

Turn off the power switch immediately and consult your dealer. Be

sure to provide the dealer with the model name and information that

appeared in the remote controller display.

Draining water or motor rotation sound is heard.

■ When cooling operation stops, the drain pump operates and then

stops. Wait approximately 5 minutes.

The vanes do not move or the indoor unit does not respond to input from

the wireless remote controller.

■ The junction wire connectors of the vane motor and signal receiver

may not be connected correctly. Have an installer check the connec-

tions. (The colors of the male and female sections of the junction wire

connectors must match.)

BH79D659H01_EN.indd 15 8/5/2016 11:07:25 AM

7.TroubleShooting

Having trouble? Here is the solution. (Unit is operating normally.)

Noise is louder than specications.

■

The indoor operation sound level is affected by the acoustics of the

particular room as shown in the following table and will be higher than

the noise specication, which was measured in anechoic room.

High sound

absorbing rooms

Normal rooms

Low sound

absorbing rooms

Location

examples

Broadcasting

studio, music

room, etc.

Reception room,

hotel lobby, etc.

Ofce, hotel

room

Noise levels 3 to 7 dB 6 to 10 dB 9 to 13 dB

Nothing appears in the wireless remote controller display, the display

is faint, or signals are not received by the indoor unit unless the remote

controller is close.

■

The batteries are low.

Replace the batteries and press the Reset button.

■

If nothing appears even after the batteries are replaced, make sure that

the batteries are installed in the correct directions (+, –).

The operation lamp near the receiver for the wireless remote controller on

the indoor unit is blinking.

■

The self diagnosis function has operated to protect the air conditioner.

■

Do not attempt to repair this equipment by yourself.

Turn off the power switch immediately and consult your dealer. Be sure

to provide the dealer with the model name.

8.Specications

Model

PLA-A12EA7 PLA-A18EA7 PLA-A24EA7 PLA-A30EA7 PLA-A36EA7 PLA-A42EA7

Power source

∙ Voltage/Frequency

<V / Hz> Single 208/230/60

Rated Input

∙ Cooling/Heating indoor only

<kW> 0.02/0.02 0.03/0.03 0.05/0.04 0.06/0.05 0.10/0.09 0.11/0.10

Rated Current

∙ Cooling/Heating indoor only

<A> 0.26/0.21 0.34/0.29 0.49/0.44 0.59/0.54 0.98/0.93 1.05/1.00

Heater <kW> – – – – – –

Height dimension <inch> 10-3/16 (1-9/16) 11-3/4 (1-9/16)

Width dimension <inch> 33-1/16 (37-3/8)

Depth dimension <inch> 33-1/16 (37-3/8)

Fan airow rate

∙ Low-Middle2-Middle1-High

/ min> 12-13-14-15 13-14-16-17 15-18-20-23 15-18-20-25 19-24-29-34 21-26-30-34

Noise level

∙ Low-Middle2-Middle1-High

<dB> 27-28-29-30 28-29-31-32 28-30-33-36 28-32-35-38 32-37-41-44 34-38-42-45

Net weight <lbs> 46 (11) 56 (11)

*1. The gure in ( ) indicates standard Grille’s.

BH79D659H01_EN.indd 16 8/5/2016 11:07:25 AM

PB 17

Index

1. Consignes de sécurité



Avant d’installer le climatiseur, lire attentivement toutes les

“Consignes de sécurité”.



Les “Consignes de sécurité” reprennent des points très impor-

tants concernant la sécurité. Veillez bien à les suivre.



Veuillez consulter ou obtenir la permission votre compagnie

d’électricité avant de connecter votre système.

Symboles utilisés dans le texte

Avertissement :

Précautions à suivre pour éviter tout danger de blessure ou de dé-

cès de l’utilisateur.

Précaution :

Décrit les précautions qui doivent être prises pour éviter d’endom-

mager l’appareil.

Symboles utilisés dans les illustrations

: Indique un élément qui doit être mis à la terre.

Avertissement :

 

 

revendeur ou à une société agréée de l’installer. Si l’appareil n’est

pas correctement installé il peut y avoir un risque de fuite d’eau,

d’électrocution ou d’incendie.

 

 -

mides. Il pourrait en résulter un risque d’électrocution.

          

sous risque d’incendie.

 





climatiseur. Cela risquerait de provoquer une mauvaise combustion.

            

l’appareil extérieur pendant son fonctionnement.

 

anormaux, arrêter l’appareil, éteindre l’interrupteur et prendre

contact avec le revendeur.

 

sorties d’air.

 



tension et contacter le revendeur. Si vous ne procédez pas de cette fa-

çon, il pourrait y avoir risque de panne, d’électrocution ou d’incendie.

 

utiliser le climatiseur sans surveillance.

 



 

Si le gaz de réfrigérant fuit, arrêter le fonctionnement du climatiseur,

aérer convenablement la pièce et prendre contact avec le reven-

deur.

 

ou spécialement formés dans des ateliers, dans l’industrie légère

ou des exploitations agricoles, ou pour une utilisation commer-

ciale par des non-spécialistes.

 Cet appareil peut être utilisé par des enfants de 8 ans et plus et

-

siques sont réduites, ou manquant d’expérience et de connais-

sances, dès lors qu’elles sont supervisées ou ont reçu une for-

mation relative à l’utilisation de l’appareil et comprennent les



l’appareil. Le nettoyage et l’entretien ne peuvent pas être effectués

par un enfant sans surveillance.

 

-

sorielles ou mentales réduites, ou manquant d’expérience et de

connaissances, à moins qu’elles ne soient supervisées ou aient

reçu des instructions relatives à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

 

pas avec l’appareil.

 -





et faire le vide d’air dans les tuyaux.

Si du réfrigérant est mélangé avec de l’air, cela peut provoquer

des pointes de pression dans les tuyaux de réfrigérant et entraîner

une explosion et d’autres risques.

 -

seur peut entraîner des défaillances mécaniques, des dysfonctionne-

ments du système ou une panne de l’appareil. Dans le pire des cas,

cela peut entraîner un obstacle à la mise en sécurité du produit.

Précaution :

 

risquerait d’endommager la commande à distance.

 

et intérieurs.



Lorsque vous devez ranger l’appareil, veuillez consulter votre revendeur.





(Pour toute information



1. Consignes de sécurité ....................................17

2. Nomenclature ..........................................18

3. Fonctionnement .........................................22

4. Minuterie ..............................................28

5. Fonctionnement d’urgence de la télécommande sans l .........28

6. Entretien et nettoyage ....................................29

7. Guide de dépannage .....................................30

8. Spécications techniques .................................31

18 19





Unité interne

PLA-A·EA7

Modes du ventilateur 4 modes

Ailette Auto avec variation

Louvre –

Filtre Longue durée

Témoin de nettoyage du

ltre

2.500 heures

Entrez le numéro du

réglage du modèle de

l’appareil intérieur que

vous souhaitez utiliser.

001

Grille de refou-

lement d’air

Filtre

Admission d’air

Ailette

Télécommande à l Télécommande sans l infrarouge

COOL

DRY

AUTO

FAN

HEAT

COOL

DRY

AUTO

FAN

HEAT

Télécommande (pièces en option)

18 19

Fri

Room

Set temp.

Mode Temp. Fan

Cool Auto

Main

Main display:

Cursor Page

Main menu

Vane·Louver·Vent. (Lossnay)

High power

Timer

Weekly timer

OU silent mode







Touches fonctions

         

l’écran.



fonctions correspondant à un écran donné.

Lorsque le système est piloté à distance, le guide de fonction des



1]

Pressez pour allumer ou éteindre l’appareil intérieur.

2]

Pressez pour enregistrer les paramètres.

3]

Pressez pour revenir à l’écran précédent.

4]

Pressez pour ouvrir le Menu général.

5 Écran LCD rétroéclairé

Les paramètres de fonctionnement s’afchent.

Lorsque le rétroéclairage est éteint, appuyer sur une touche l’allume, et

il reste allumé pendant un certain temps en fonction de l’afchage.

Lorsque le rétroéclairage est éteint, appuyer sur une touche ne fait

que l’allumer, sans exécuter la fonction. (à l’exception de la touche

[MARCHE / ARRÊT])

6

Cette lampe s’allume en vert lorsque le système est en fonctionne-

ment. Elle clignote lorsque la télécommande est en cours de démar-

rage ou en cas d’erreur.

7

Ecran principal : Pressez pour régler le mode de fonctionnement.

Menu général : Pressez pour faire descendre le curseur.

8

Ecran principal : Pressez pour diminuer la température.

Menu général : Pressez pour faire monter le curseur.

9

Ecran principal : Pressez pour augmenter la température.

Menu général : Pressez pour revenir à l’écran précédent.

0

Ecran principal : Pressez pour changer la vitesse du ventilateur.

Menu général : Pressez pour aller à la page suivante.

Interface de la télécommande

4 3 2 1

7 8 9 0

 

Guide des fonctions

7 8 9 0 7 8 9 0

 



L’écran principal peut être afché dans deux modes différents : “complet” et “basic”. Le réglage usine est “complet”. Pour passer au mode “basic”,

changez-le dans l’écran principal. (Reportez-vous au manuel d’utilisation inclus avec la télécommande.)

1 

Le mode de fonctionnement de l’appareil intérieur s’afche ici.

2 Température programmée

La température programmée s’afche ici.

3

L’heure actuelle s’afche ici.

4 Vitesse du ventilateur

Le réglage de la vitesse de ventilation apparaît ici.

5

Les fonctions correspondant aux touches s’afchent ici.

6

S’afche lorsque la marche et l’arrêt sont pilotés de façon centralisée.

7

S’afche lorsque le mode de fonctionnement est piloté de façon cen-

tralisée.

8

S’afche lorsque la température sélectionnée est pilotée de façon

centralisée.

9

S’afche si la remise à zéro du ltre est pilotée de façon centralisée.

0

Indique si le ltre a besoin d’entretien.

1 Température de la pièce (Voir le manuel d’installation.)

La température actuelle de la pièce s’afche ici.

2

S’afche lorsque les touches sont verrouillées.

* Toutes les icônes sont afchées pour la compréhension.

3

Apparaît lorsque la fonction « ON/OFF timer », « Réduit de nuit » ou

« Arrêt Auto » timer est activée.

apparaît lorsque le timer est désactivé par le système de contrôle

centralisé.

4

S’afche si le programmateur hebdomadaire est activé.

5

S’afche lorsque le système est en mode économie d’énergie. (Ceci

n’apparaîtra pas sur certains modèles d’unités intérieures)

6

S’afche lorsque les appareils extérieurs sont en mode silencieux.

7

S’afche lorsque la thermistance intégrée à la télécommande est utili-

sée pour mesurer la température de la pièce (1).

s’afche lorsque la thermistance de l’appareil intérieur est utilisée

pour mesurer la température de la pièce.

8

S’afche quand les unités fonctionnent en mode d’économie d’énergie

avec le capteur 3D i-see.

9

Indique le réglage du déecteur.

)

Indique le réglage des ailettes.

(Cette indication n’est pas disponible pour ce modéle.)

!

Indique les réglages de la ventilation.

@

S’afche lorsque la plage de température de réglage est réduite.

La plupart des paramètres (à l’exception de la Marche / Arrêt, du mode, de la vitesse du ventilateur, de la température)

peuvent être réglés à partir de l’écran du menu. (Reportez-vous au manuel d’utilisation inclus avec la télécommande.)



Fri

Mode Temp. Fan

Room

Cool

Set temp.

)

2 3 4 5 6 8 9

Fri

Cool

Mode Temp. Fan

Set temp.

La page est en cours de chargement...

Mitsubishi Electric PLA-A12EA7 Le manuel du propriétaire

Marque: Mitsubishi Electric

Modèle: PLA-A12EA7

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Mitsubishi Electric PLA-A12EA7 Owner's manual
español: Mitsubishi Electric PLA-A12EA7 El manual del propietario

Mitsubishi Electric PLA-A12EA7 Le manuel du propriétaire

Ce manuel convient également à

Mitsubishi Electric PLA-A12EA7 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents