PROPOINT 8844037 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8844037

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

V1.1 8844037

Please read and understand all instructions before use. Retain this manual for future

reference.

3/4 X 20-1/2 IN.

AIR BELT SANDER•

8844037 3/4 x 20-1/2 in. Air Belt S ande r V1.1

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Belt Size 3/4 x 20-1/2 in.

Paper Size

3/4 x 20-1/2 in.

Air Inlet 1/4 in.

Pressure Range 90 PSI

Air Consumption

3.8 CFM

Speed Rating 18,000 RPM

Min. Hose Size 3/8 in.

Material

Composite Housing with Cushioned Grip

Includes (2) Hex Keys, (3) Sanding Belts

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice

that could result in severe personal injury or death if the

proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

NOTICE! This notice indicates that a specific hazard or unsafe

practice will result in equipment or property damage, but

not personal injury.

V1.1 3/4 x 20-1/2 in. Air Belt S ander 8844037

Visit www.princessauto.com for more information 3

SAFETY

WARNING! Read and understand all instructions before using this

tool. The operator must follow basic precautions to reduce the

risk of personal injury and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or

inspection and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean,

well-lit and free of distractions. Place lights so you are not working

in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store unused tools properly in a safe and dry location to prevent rust

or damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust

or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the

Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or

to reduce the effects of tool vibration.

4. Wear protective clothing designed for the work environment and tool.

5. Non-skid footwear is recommended to maintain footing and

balance in the work environment.

8844037 3/4 x 20-1/2 in. Air Belt S ande r V1.1

4 For technical questions call 1-800-665-8685

6. This tool can cause hearing damage. Wear hearing protection gear

with an appropriate Noise Reduction Rating to withstand the

decibel levels.

7. The tool may contain high pressure. Use safety glasses and gloves

for protection during operation. Keep hands clear of the exposed

rubber portions of the hose.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with

the moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and

balance enables better control in unexpected situations.

4. Keep your fingers away from the trigger/switch while carrying the

tool, attaching an air hose or an accessory. Lock the trigger/switch

safety if available.

5. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

6. Never point the air stream or tool at any point of your body, other

people or animals. Debris and dust ejected at high speed can

cause an injury.

7. Serious injury or death may occur from inhaling compressed air.

The air stream may contain carbon monoxide, toxic vapors or solid

particles. Never inhale compressed air directly from the pump or

air tool.

8. Support the workpiece or clamp it to a stable platform. Holding the

workpiece by hand or against your body may lead to personal injury.

9. Securely hold this tool using both hands. Using a tool with only one

hand can result in loss of control.

V1.1 3/4 x 20-1/2 in. Air Belt S ander 8844037

Visit www.princessauto.com for more information 5

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to the tool safety

rules. If you use this tool unsafely or incorrectly, you can suffer

serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for an

unintended purpose.

2. Do not use the tool if any parts are damage broken or misplaced.

Repair or replace the parts.

3. Do not use any power tool with a malfunctioning power switch or

control. A power tool that fails to respond to the controls is

dangerous and can cause an injury. A qualified technician must

repair and verify the power tool is operating correctly, before it can

be used.

4. Do not cover the air vents.

5. Disconnect the power source before installing or servicing the tool.

6. Before using the tool on a workpiece, test the tool by running it at

the highest speed rating for at least 30 seconds in a safe position.

Stop immediately if there is any abnormal vibration or wobbling.

Check the tool to determine the cause.

7. Never force the tool. Excessive pressure could break the tool,

resulting in damage to your workpiece or serious personal injury.

Excessive pressure is the cause if your tool runs smoothly under no

load, but roughly under load.

8. Keep hands and fingers away from the work area. Any part of body

contacting the tool’s working parts could cause an injury.

9. Never touch the tool accessory or workpiece during or immediately

after use. They may be hot and could inflict a burn injury.

10. Do not place the tool down until the tool’s accessory has stopped

moving. The accessory may catch the surface of work material and

wrench itself free, causing injury to the user or others in the work area.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

8844037 3/4 x 20-1/2 in. Air Belt S ande r V1.1

6 For technical questions call 1-800-665-8685

2. Install an in-line shutoff valve or regulator to allow immediate control

over the air supply in an emergency, even if a hose is ruptured.

3. Discontinue tool use if it does not work properly or air is leaking.

Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated to

never exceed the maximum pressure rating of the tool (see

Specifications). Exceeding the maximum PSI rating can create a

bursting hazard, causing injury and property damage.

5. Never use oxygen, combustible gas or any other bottled gas as a

power source. Any power source other than an air compressor

could cause an explosion and serious personal injury.

6. Turn OFF the valve and discharge any remaining air pressure after

each use or before adjusting the tool.

7. Do not leave the air tool unattended with its compressed air supply

on. Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

8. Serious injury may occur from loose debris being propelled at high

speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the

air compressor.

9. Always turn off the air compressor and drain tank pressure

completely before attempting maintenance or attaching air tools.

Release pressure slowly from the system.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing is

heard from the air hose or couplers. Replace the defective air hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the

air hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose behind the tool and out of the tool's work p ath.

V1.1 3/4 x 20-1/2 in. Air Belt S ander 8844037

Visit www.princessauto.com for more information 7

c. Keep the air hose away from heat, oil, sharp edges or

moving parts.

d. Do not wrap the air hose around the tool as sharp edges may

pierce or crack the air hose. Gently coil the hose and either

hang on a hook or fasten with a device to keep hose together

when storing.

4. A damaged or disconnected air hose under pressure may whip

around and inflict personal injury or damage the work area. Secure

the compressor's air hose to a fixed or permanent structure with

clamps or cable ties.

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to

vibration may cause temporary or permanent physical injury. Take

frequent breaks when using the tool.

2. If you feel any medical symptoms related to vibrations (such as

tingling, numbness, and white or blue fingers), seek medical

attention as soon as possible.

3. Wear suitable gloves to reduce the effects of vibration.

4. DO NOT use this tool before consulting a physician if one of the

following applies:

a. Pregnant

b. Impaired blood

circulation to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace

the missing part before operating. Failure to do so could result in

a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect

for damage.

Make sure that all items in the parts list are included.

8844037 3/4 X 20-1/2 in. Air Belt S ander V1.1

8 For technical questions call 1-800-665-8685

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

INSTALLING THE AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use

with your tool.

1. Wrap the external threads of the coupler plug with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the coupler plug into the tool's air inlet (#1) and tighten with

a wrench until snug.

3. Run the compressor at a low volume and check the connection for

air leaks. Do not use the tool until all air leaks are repaired or the

faulty component is replaced.

IMPORTANT! Vibration may cause failure if a quick coupler is

connected directly to the air tool. To overcome this, connect a

leader hose to the tool. A quick coupler may then be used to

connect the leader hose to the air line hose.

INSTALLING THE SANDING BELT

1. Remove the rubber guard (#37)

2. Retract the belt arm until the tension bar (#34) engages and the

arm locks in place.

3. Install the sanding belt on the arm. Ensure that the belt is aligned

with the drive (#26) and idle (#38) pulleys.

4. Secure the sanding belt by pressing the tension bar to release

the arm.

ADJUSTING THE BELT ANGLE

1. Press the belt arm lever (#29) upwards to unlock.

2. Adjust the angle of the belt arm to the desired position. Ensure that

the arm is pressed tightly towards the motor housing (#7) for

optimal belt tracking.

3. Clamp down the belt arm lever (#29) to lock. If the arm is still loose,

tighten the belt arm screw (#36).

V1.1 3/4 X 20-1/2 in. Ai r Belt S ander 8844037

Visit www.princessauto.com for more information 9

OPERATION

1. Grip the sander and make sure the sanding belt is not touching any

surface before you turn on the tool. Gently press the throttle

lever (#11) to allow the sanding belt to rotate to its maximum speed.

2. Rotate the regulator knob (#8) clockwise to increase the speed

and counterclockwise to decrease.

3. Place the rotating sanding belt on the workpiece, being careful not

to strike the workpiece with the sides of the tension bar (#34).

Move the sander back and forth to remove material.

NOTICE! Keep a light pressure on the sander when in use. Do not

apply heavy pressure as damage to the work surface may result.

3. When finished using the sander, release pressure on the throttle

lever. Turn off the air compressor. Squeeze the throttle lever again

to release any remaining compressed air in the sander. Then

disconnect the air hose from the tool.

PRESSURE DROP

Apply the air consumption and pressure rate numbers to the tool’s air

inlet, not the compressor’s outlet. Calculate the pressure drop for your

air supply set-up and increase the compressor outlet pressure to

compensate. Make sure you do not exceed the maximum pressure for

any part of your air supply system.

Installing a pressure gauge at the tool inlet is the best way to measure

the air pressure and adjust the compressor’s output.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool fittings, alignment, hoses and power supply cord

periodically. Have damaged or worn components repaired or replaced

by an authorized technician. Only use identical replacement parts

when servicing.

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool handles clean, dry and free from oil/grease at

all times.

8844037 3/4 X 20-1/2 in. Air Belt S ander V1.1

10 For technical questions call 1-800-665-8685

6. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd.

for replacements.

WARNING! Only qualified service personnel should repair the

tool. An improperly repaired tool may present a hazard to the

user and/or others.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other

lubricants are not suitable and will damage the tool or cause a

malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool.

Penetrating oil acts as a solvent that will dissolve the tool’s

grease packing and may damage the O-rings, causing the tool to

seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a

generous amount of air tool oil in the air inlet (#1) and then run the

tool under no load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s male

coupler before each use and after every hour of continuous use.

The tool will not work properly without lubrication and parts will

wear prematurely.

3. Avoid adding too much air tool oil as this can cause premature

power loss and eventual tool failure. A qualified technician will need

to take the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing it

for an extended period of time (overnight, weekend, etc.). Run the

tool for approximately 30 seconds to ensure the oil is evenly

distributed throughout the tool. Store it in a clean and dry location.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws

for electronic devices, batteries, oil or other toxic liquids.

V1.1 3/4 X 20-1/2 in. Ai r Belt S ander 8844037

Visit www.princessauto.com for more information 11

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

PROBLEM(S) POSSIBLE CAUSE(S) SUGGESTED

SOLUTION(S)

Tool runs at

normal speed,

but loses power

under load.

Motor parts worn.

Have a qualified

technician service the

tool.

Replace tool or parts.

Tool runs

slowly. Air flows

slightly from

exhaust.

Motor parts jammed with dirt

particles.

Airflow blocked by dirt.

Check air inlet filter for

blockage.

Pour air tool lubricating

oil into air inlet as per

lubrication instructions

for clearing

shipping grease.

Operate tool in short

bursts to clear debris.

If tool still jammed,

clean tool and

lubricate per

lubrication instructions.

Air regulator in closed position. Open the air regulator

to desired airflow.

Tools will not

run. Air flows

freely from

exhaust.

Damage or excessive wearing of

internal parts.

Have a qualified

technician service the

tool.

Replace tool or parts.

Tool will not

shut off.

1. Throttle valve O-ring

dislodged from seat inlet

valve.

2. Trigger mechanism jammed

or dirty.

1. Replace throttle

valve O-rings.

2. Clean trigger

mechanism and

lubricate.

8844037 3/4 X 20-1/2 in. Air Belt S ander V1.1

12 For technical questions call 1-800-665-8685

Loss of power

or erratic

performance.

Excessive drain on the air

hose. Incorrect size or type

of hose couplers.

2. Moisture or restriction in the

air hose/tank

3. Air compressor has

insufficient flow.

Check the air

hose and confirm

the hose fitting is

correct for the inlet

bushing.

2. Depressurize

system and drain

tank and air hose

of water.

3. Ensure tool is

connected to a

compressor with a

rate flow that

matches the tool.

V1.1 3/4 X 20-1/2 in. Ai r Belt S ander 8844037

Visit www.princessauto.com for more information 13

PARTS BREAKDOWN

PARTS LIST

# DESCRIPTION QTY

1 Air Inlet 1

2 Exhaust Sleeve 1

Silencer

4 Spring 1

5 Valve 1

Washer

7 Motor Housing 1

Regulator Set

9 Valve Stem Set 1

10 Snap Ring 1

Lever

Spring Pin

13 Cap 1

14 O-Ring 1

Bearing

16 Rear Plate 1

17 Packing 1

Cylinder Set

19 Rotor Blade 6

Rotor

21 Key 1

22 Bearing Spacer 1

Front Plate

8844037 3/4 X 20-1/2 in. Air Belt S ander V1.1

14 For technical questions call 1-800-665-8685

24 Bearing 1

Drive Pulley

27 Washer 1

Nut

29 Trigger 1

30 Bushing 1

Hub Guard

32 Screw 1

33 Screw 1

Tension Bar Set

35 Shoe 1

Screw

37 Shroud 1

Spring

39 Screw 1

Screw

41 Idle Pulley Set 1

42 Spring Pin 1

Sanding Belt 40 Grit

43 Sanding Belt 60 Grit 1

43 Sanding Belt 80 Grit 1

Hex Key 2 mm

45 Hex Key 3 mm 1

V1.1 3/4 X 20-1/2 in. Ai r Belt S ander 8844037

Visit www.princessauto.com for more information 15

8844037 3/4 X 20-1/2 in. Air Belt S ander V1.1

16 For technical questions call 1-800-665-8685

V1,1 8844037

Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce

manuel afin de pouvoir le consulter plus tard.

PONCEUSE PNEUMATIQUE

À COURROIE•

3/4 X 20 1/2 PO

8844037 Ponceus e pneumat ique à courroie, 3/4 x 20 1/2 po V1,1

2 En cas de questions techniques, appelez le 1-800-665-8685

SPÉCIFICATIONS

Taille de courroie 3/4 x 20 1/2 po

Format de papier

3/4 x 20 1/2 po

Entrée d’air 1/4 po

Pression nominale

90 lb/po carré

Consommation d’air à 90

lb/po carré

3,8 pi cubes/min

Vitesse nominale

18 000 tr/min

Taille min. de tuyau 3/8 po

Matériau Boîtier en composite avec poignée coussinée

Comprend

(2) clés hexagonales, (3) courroies abrasives

DÉFINITIONS DE DANGER

Veuillez-vous familiariser avec les avis de danger qui sont présentés

dans ce manuel. Un avis est une alerte indiquant qu'il existe un risque

de dommage à la propriété, de blessure ou de décès si on ne respecte

pas certaines instructions.

DANGER ! Cet avis indique un risque immédiat et particulier

qui entraînera des blessures corporelles graves

ou même la mort si on omet de prendre les

précautions nécessaires.

AVERTISSEMENT ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui pourrait entraîner des

blessures corporelles graves ou même la mort si

on omet de prendre les précautions nécessaires.

ATTENTION ! Cet avis indique une situation possiblement

dangereuse qui peut entraîner des blessures

mineures ou modérées si on ne procède pas de la

façon recommandée.

AVIS ! Cet avis indique un risque particulier ou une

pratique non sécuritaire qui entraînera des

dommages au niveau de l'équipement ou des

biens, mais non des blessures corporelles.

V1,1 Ponceus e pneumat ique à courroi e, 3/4 x 20 1/2 po 8844037

Visitez www.princ essauto.com pour plus d'informations 3

SÉCURITÉ

AVERTISSEMENT ! Veuillez lire et comprendre toutes les

instructions avant d'utiliser cet outil. L'utilisateur doit respecter

les précautions de base lorsqu'il utilise cet outil afin de réduire

le risque de blessure ou de dommage à l'équipement.

Conservez ce manuel qui contient les avertissements de sécurité, les

précautions, les instructions de fonctionnement ou d'inspection

et d'entretien.

AIRE DE TRAVAIL

1. Travaillez dans un environnement de travail sécuritaire. Gardez votre

aire de travail propre, bien éclairée et exempte de toute distraction.

Placez les lampes de façon à ne pas travailler dans l’ombre.

2. Assurez-vous que les personnes qui ne portent pas l'équipement de

sécurité approprié ne se trouvent pas à proximité de l'aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

4. N'installez pas et n'utilisez pas d'outils électriques en présence de

gaz, de poussière ou de liquides inflammables.

SÉCURITÉ PERSONNELLE

AVERTISSEMENT ! Portez de l'équipement de protection personnelle

homologué par l'Association canadienne de normalisation (CSA) ou

l'American National Standards Institute (ANSI).

ÉQUIPEMENT DE PROTECTION PERSONNELLE

1. Portez toujours des lunettes antiprojections qui offrent une

protection frontale et latérale pour les yeux. L'équipement de

protection des yeux devrait être conforme à la norme CSA Z94.3-

07 ou ANSI Z87.1 fonction du type de travail effectué.

2. Portez un écran facial panoramique de type approprié avec les

lunettes de sécurité puisque cette tâche peut créer des copeaux,

des matières abrasives ou des particules.

3. Portez des gants qui protègent en fonction des matériaux de travail

et pour réduire les effets des vibrations de l'outil.

4. Portez des vêtements de protection conçus pour l'environnement

de travail et pour l'outil.

8844037 Ponceus e pneumat ique à courroie, 3/4 x 20 1/2 po V1,1

4 En cas de questions techniques, appelez le 1-800-665-8685

5. Les chaussures antidérapantes sont recommandées pour maintenir

la stabilité et l'équilibre au sein de l'environnement de travail.

6. Cet outil peut causer des dommages à l'ouïe. Portez un dispositif

de protection anti-bruit présentant une cote de réduction du bruit

adéquate en fonction du niveau de décibels.

7. L’outil peut être à haute pression. Portez des lunettes de sécurité et

des gants pour vous protéger au cours de l'opération. Gardez les

mains à l'écart des parties de caoutchouc exposées du tuyau.

PRÉCAUTIONS PERSONNELLES

Gardez le contrôle de l'outil, de vos mouvements et de l'environnement

de travail pour éviter les blessures ou le bris de l'outil.

1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,

d'alcool ou de médicaments.

2. Évitez de porter des vêtements ou des bijoux pouvant se prendre

dans les pièces mobiles d'un outil. Gardez les cheveux longs

recouverts ou attachés.

3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en

servir. Une stabilité et un équilibre appropriés sont nécessaires afin

d'avoir un meilleur contrôle en cas de situations inattendues.

4. Gardez vos doigts à bonne distance de la gâchette/commutateur

lors du transport de l’outil ou du branchement d’un tuyau à air ou

d’un accessoire. Engagez le verrou de gâchette/interrupteur, le

cas échéant.

5. Évitez les mises en marche involontaires. Assurez-vous que le

régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque

l’outil n’est pas utilisé et avant de le brancher à une source d’air.

6. Ne dirigez jamais le jet d’air ou les outils vers votre corps, d’autres

individus ou des animaux. Les débris et la poussière projetés à

grande vitesse peuvent causer des blessures.

7. Des blessures graves ou même la mort peuvent survenir en cas

d’inhalation de l’air comprimé. Le jet d’air peut contenir du

monoxyde de carbone, des vapeurs toxiques ou des particules

solides. N’inhalez jamais l’air comprimé provenant directement de

la pompe ou d’un outil pneumatique.

La page charge ...

PROPOINT 8844037 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 8844037

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 8844037 Owner's manual

PROPOINT 8844037 Le manuel du propriétaire

PROPOINT 8844037 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents