Homelite UT26HBV Mode d'emploi

Marque: Homelite

Modèle: UT26HBV

Catégorie: Souffleurs / sécheurs d'air

Taper: Mode d'emploi

Cette soufflante a été conçue et fabriquée conformément aux

strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des

années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

26cc BLOWER/VACUUM

SOUFFLANTE /ASPIRATEUR

DE 26 cc

SOPLADORA /ASPIRADORA

DE 26 cc

UT26HBV / UT26HBVEMC

Your blower has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before

using this product.

Thank you for your purchase.

Su sopladora ha sido diseñada y fabricada de conformidad con

las estrictas normas para brindar fiabilidad, facilidad de uso y

seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Agradecemos su compra.

SAVE THIS MANUAL FOR FUTURE REFERENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

To register your Homelite product, please visit:

http://register.homelite.com/

Pour enregistrer votre produit de Homelite, s’il vous plaît

la visite : http://register.homelite.com/

Para registrar su producto de Homelite, por favor visita:

http://register.homelite.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage

the unit and void your warranty. Only use unleaded gasoline containing up to 10% ethanol.

Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une telle utilisation représente une

violation de la loi fédérale et endommagera l’appareil et annulera la garantie. Utiliser seulement de l’essence sans plomb ne

contenant pas plus de 10 % d’éthanol.

No utilice combustibles E15 o E85 con este producto. Esto constituye una violación a la ley federal, dañará la unidad y anulará

la garantía. Utilice únicamente gasolina sin plomo que contiene hasta 10% de etanol.

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin

d’examiner toutes les figures mentionnées

dans le manuel d’utilisation.

Consulte esta sección desplegable para

ver todas las figuras a las que se hace referencia

en el manual del operador.

Fig. 1

A - Lower vacuum tube (tube d’aspiration inférieur, tubo inferior de la

aspiradora)

B - Shoulder strap (bandoulière, correa para el hombro)

C - Cruise control lever/throttle lock (levier de régulateur de vitesse /

verrouillage d’accélération, palanca de control de crucero/seguro del

acelerador)

D - Upper vacuum tube (tube d’aspiration supérieur, tubo superior de la

aspiradora)

E - Vacuum tube screw (vis de tube d’aspiration, tornillo de tubo de la

aspiradora)

F - Vacuum bag (sac à débris, saco de la aspiradora)

G - Throttle trigger (gâchette d’accélérateur, gatillo del acelerador)

H - Stop switch (commutateur d’arrêt, interruptor del apagado)

I - Vacuum handle (poignée d’aspirateur, mango de la aspiradora )

J - Fuel cap (bouchon du réservoir, tapa del tanque de combustible)

K - Starter grip and rope (poignée du lanceur et corde, mango del

arrancador y cuerda)

L - Primer bulb (poire d’amorçage, bomba de cebado)

M - Choke lever (levier de volet de départ, palanca del anegador)

N - Upper handle (poignée supérieure, mango superior)

O - Vacuum bag adaptor (adaptateur de sac à débris, adaptador del

saco de la aspiradora)

P - Muffler (silencieux, silenciador)

Q - Raised slot (fente en saillie, ranura realzada)

R - Upper blower tube (tube supérieur de soufflante, tubo superior de

la sopladora)

S - Sweeper nozzle (embout éventail, boquilla para barrer)

T - High velocity nozzle (embout haute vélocité, boquilla de alta

velocidad opcional)

iii

Fig. 3

Fig. 2

Fig. 4

Fig. 6

Fig. 7

Fig. 5

A - Upper blower tube (tube de soufflante

supérieur, tubo superior de la sopladora)

B - Sweeper nozzle (embout éventail, boquilla

para barrer)

C - High velocity nozzle (embout haute vélocité,

boquilla de alta velocidad)

A - Sweeper nozzle (embout éventail, boquilla

para barrer)

B - Upper blower tube (tube de soufflante

supérieur, tubo superior de la sopladora)

C - Blower housing outlet (sortie du logement

de la soufflante, salida del armazón de la

sopladora)

D - High velocity nozzle (embout haute vélocité,

boquilla de alta velocidad)

A - Adaptor installed in vacuum bag (adaptateur

installé dans le sac à débris, adaptador

instalado en el saco de la aspiradora)

B - Raised locking tab (languette de verrouillage

en saillie, orejeta realzada de aseguramiento)

C - Raised slot (fente en saillie, ranura realzada)

A - Vacuum bag assembly (ensemble de sac à

débris, conjunto del saco de la aspiradora)

B - Vacuum inlet door (volet d’entrée d’air,

puerta de la entrada de la aspiradora)

C - Door tab (languette du volet, orejeta de la

puerta)

D - Tab (languette, orejeta)

A - Vacuum bag adaptor (adaptateur de sac à

débris, adaptador del saco de la aspiradora)

B - Vacuum bag (sac à débris, saco de la

aspiradora)

C - Cable tie (attache de câble, amarra para

cable)

A - Flat head screwdriver (tournevis à lame

plate, destornillador de punta plana)

Fig. 8

Fig. 9

A - Vacuum tube assembly (ensemble de tubes

d’aspiration, conjunto de los tubos de la

aspiradora)

B - Vacuum inlet door (volet d’entrée d’air,

puerta de la entrada de la aspiradora)

C - Screw (vis, tornillo)

D - Vacuum opening (ouverture d’aspiration,

abertura de aspiración)

E - Screw mount (trous de vis, agujeros de

tornillos)

A - Stop switch (commutateur d’arrêt,

interruptor del apagado)

B - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

C - Cruise control lever/throttle lock (levier

de régulateur de vitesse / verrouillage

d’accélération, palanca de control de

crucero/seguro del acelerador)

D - Primer bulb (poire d’amorçage, bomba de

cebado)

E - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

Fig. 10

Fig. 13

Fig. 14

Fig. 15

Fig. 11

Fig. 12

A - Sweeper nozzle (embout éventail, boquilla

para barrer)

B - High velocity nozzle (embout haute vélocité,

boquilla de alta velocidad)

A - Turn the dial to open and close (tourner

le cadran pour ouvrir et fermeture, gire el

selector para abrirla y cerrar )

B - Air filter cover (couvercle du filtre à air, tapa

de la cámara de ventilación)

A - Air filter cover (couvercle du filtre à air,

cámara del filtro de aire)

B - Air filter (filtre à air, filtro de aire)

A - Cruise control lever (levier de régulateur de

vitesse, palanca de control de crucero)

B - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

PROPER BLOWER OPERATING POSITION

POSITION D’UTILISATION ADÉQUATE

DE LA SOUFFLANTE

POSICIÓN DE FUNCIONAMIENTO

CORRECTA DE LA SOPLADORA

PROPER VACUUM

OPERATING POSITION

POSITION D’UTILISATION ADÉQUATE

DE L’ASPIRATEUR

POSICIÓN DE FUNCIONAMIENTO

CORRECTA DE LA ASPIRADORA

A - Keep muffler away from the body (garder les

mains à l’écart des silencieux, mantenga el

silenciador alejado del cuerpo)

Page / Página 2

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules ........................................................................................................................................................ 3

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................................................4

Règles de sécurité particulières / Reglas de seguridad específicas

 Symbols ............................................................................................................................................................................5

Symboles / Símbolos

 Features ............................................................................................................................................................................6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-7

Assemblage / Armado

 Operation ..................................................................................................................................................................... 8-10

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................11-12

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 13

Dépannage / Solución de problemas

 Warranty ......................................................................................................................................................................... 14

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

Page 3 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS. Fail-

ure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

Do not allow children or untrained individuals to use this

unit.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

Keep all bystanders, children, and pets at least 50 ft.

away.

Wear heavy long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

jewelry of any kind, or go barefoot.

To reduce the risk of injury associated with objects being

drawn into rotating parts, do not wear loose clothing,

scarves, neck chains, and the like.

Secure long hair so it is above shoulder level to prevent

entanglement in any rotating parts.

Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

Do not operate in poor lighting.

Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

Wear a face filter mask in dusty conditions to reduce the

risk of injury associated with the inhalation of dust.

Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the machine.

Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.

Before storing, allow the engine to cool.

Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.

To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

Do not smoke while handling fuel.

Mix and store fuel in a container approved for gasoline.

Mix fuel outdoors where there are no sparks or flames.

Select bare ground, stop engine, and allow to cool before

refueling.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Tighten the fuel cap securely after refueling.

Wipe spilled fuel from the unit. Move 30 ft. away from

refueling site before starting engine.

Never attempt to burn off spilled fuel under any

circumstances.

Use only recommended or equivalent manufacturer’s

replacement parts and accessories. Use of any other

parts may create a hazard or cause product damage.

Maintain the unit per maintenance instructions in this

Operator’s Manual.

Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

Do not use on a ladder, rooftop, tree, or other unstable

support. Stable footing on a solid surface enables better

control of the blower in unexpected situations.



Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent starting.



We recommend taking your equipment to a qualified

service center for repair, as service performed by in-

experienced or unqualified persons may damage the

equipment, create unsafe conditions, injury to user and/

or void your warranty.

GENERAL SAFETY RULES

Page 4 — English

Always hold the blower/vacuum in your right hand during

blower operation. Refer to the Operation instructions later

in this manual for proper position during vacuum opera-

tion and additional information.

Never place objects inside the blower tubes.

Use only as directed in this operator’s manual.

Do not operate vacuum without vacuum bag installed;

flying debris could cause serious injury. Always close

vacuum bag completely before operating.

Rotating impeller blades can cause severe injury. Stop

the engine and ensure impeller blades have stopped

rotating before opening the vacuum door or installing/

changing tubes. Do not put hands or any other object

into the vacuum tubes while they are installed on the unit.

 Never run the unit without the proper equipment attached.

When used as a blower, always install the blower tubes.

When used as a vacuum, always install the vacuum

tubes and vacuum bag. Make sure the vacuum bag is

completely zipped when the unit is running to avoid flying

debris.

 Avoid situations that could catch the vacuum bag on

fire. Do not operate near an open flame. Do not vacuum

warm ash from fireplaces, barbecue pits, brush piles, etc.

Do not vacuum discarded cigars or cigarettes unless the

cinders are completely cool.

 Never place blower on any surface, except a hard, clean

surface when engine is running. Gravel, sand, and other

debris can be picked up by the air inlet and thrown at the

operator or bystanders, causing possible serious injuries.

 To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

 To reduce the risk of injury associated with contacting

rotating parts, stop the engine before installing or

removing attachments. Always disconnect the spark plug

before performing maintenance or accessing any movable

parts.

 Never use blower near fires, fireplaces, hot ashes,

barbecue pits, etc., which may cause fire to spread.

 Do not point the blower nozzle in the direction of people

or pets.

 This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-

tions as blowing leaves and lawn clippings, etc. It is not

intended for prolonged use. Prolonged periods of opera-

tion can cause circulatory problems in the user’s hands

due to vibration. For such use, it may be appropriate to

use a product having an anti-vibration feature.

FUELING

 Fuel is highly flammable. Take precautions when using

to reduce the chance of serious personal injury.

 Store fuel in a cool, well-ventilated area, safely away from

spark and/or flame-producing equipment.

 Store fuel in containers specifically designed for this

purpose.

 Only refuel outdoors and do not smoke while refueling.

 Add fuel before starting the engine. Never remove the cap

of the fuel tank or add fuel while the engine is running or

when the engine is hot.

 Do not smoke while handling fuel.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or flames.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

 Never attempt to burn off spilled fuel under any circum-

stances.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

 Replace all fuel tank and container caps securely.

 Empty fuel tank into a container approved for gasoline

and restrain the unit from moving before transporting in

a vehicle.

 When draining the fuel tank, use an approved fuel storage

container in a well-ventilated area.

 Select bare ground, stop engine, and allow to cool before

refueling.

 Save these instructions. Refer to them frequently and use

them to instruct others who may use this tool. If you loan

someone this tool, loan them these instructions also.

SPECIFIC SAFETY RULES

Page 5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME EXPLANATION

Safety Alert Symbol Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing protection when

operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or

property damage.

Vacuum Door Do not run unit while vacuum door is unsecured.

Long Hair Risk of long hair being drawn into air inlet.

Blower Tubes Do not run unit without tubes in place.

Loose Clothing Risk of loose clothing being drawn into air intake.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use with

an octane rating of 87 [(R + M) / 2] or higher. This product is

and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicate a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

Page 6 — English

PRODUCT SPECIFICATIONS

Engine Displacement.......................................................................................................................................................26cc

Air Velocity: Sweeper Nozzle High Velocity Nozzle

*MPH ....................................................................................... 150 ..............................................................200

*CFM ....................................................................................... 400 ..............................................................150

*Rated per ANSI B175.2

KNOW YOUR BLOWER/VACUUM

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

BLOWER TUBE AND SWEEPER NOZZLE

The blower tube and sweeper nozzle can be assembled and

installed on the blower without using any tools.

CRUISE CONTROL LEVER/THROTTLE LOCK

The cruise control lever/throttle lock feature allows the user

to operate the blower without holding the throttle trigger.

To slow the engine, simply push the cruise control lever/

throttle lock forward.

ENGINE

The blower has a powerful 26cc engine with sufficient power

to handle tough blowing and vacuuming jobs.

HIGH VELOCITY NOZZLE

The high velocity nozzle is great for wet sticky leaves. It al-

lows you to scrape wet leaves or debris from hard surfaces

while operating the blower.

SWEEPER NOZZLE

The sweeper nozzle allows for more area to be covered

during blower operation, making it more effective on larger

piles of leaves and debris.

THROTTLE TRIGGER

The blower can be operated at any speed between idle and

full throttle.

VACUUM/MULCHER

Converting the blower to a vacuum/mulcher is simple and

can be done using a flat head screwdriver.

VACUUM BAG

The vacuum bag attaches to the blower easily by using the

vacuum bag adaptor.

VACUUM HANDLE

This feature allows user to perform vacuuming duties

comfortably.

VACUUM TUBES

The vacuum tubes can be installed on the blower using a

flat head screwdriver.

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

FEATURES

ASSEMBLY

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Blower

Upper Blower Tube

Sweeper Nozzle

High Velocity Nozzle

Upper and Lower Vacuum Tubes

Vacuum Tube Screws (2)

Vacuum Bag

Page 7 — English

PACKING LIST (continued)

Vacuum Bag Adaptor

2-Cycle Engine Lubricant

Operator’s Manual

NOTE: Read and remove all hang tags and store with your

Operator’s Manual.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of the product

with damaged or missing parts could result in possible

serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

TOOLS NEEDED

See Figure 2.

The following tool (not included or drawn to scale) is needed

for assembly:

 Flat Head Screwdriver

ASSEMBLING THE BLOWER TUBES

See Figures 3 - 4.

 Align raised tabs on blower housing outlet to the slots on

upper blower tube; slide together and tighten securely

by twisting until the tubes snap into the locked position.

Check tightness after initial use and retighten if needed.

NOTICE:

When correctly assembled, the tubes are difficult to sepa-

rate. If they can easily be twisted apart, the tubes are not

locked. Continue twisting together until the tubes snap

into the locked position. Tubes that are not fully locked

together can separate during blower operation.

 Attach sweeper nozzle to upper blower tube by aligning

raised tabs on upper blower tube; slide together and

tighten securely by twisting. Check tightness after initial

use and retighten if needed.

 If high velocity nozzle use is desired, attach to sweeper

nozzle by aligning raised tab on high velocity nozzle with

slot on sweeper nozzle.

 To remove the tubes, use a flat head screwdriver to lift the

locking tab, rotate the tubes to unlock them and remove

from the blower housing outlet.

INSTALLING THE VACUUM BAG

See Figures 5 - 6.

 Remove the nozzle and upper blower tube from the

blower by using a flat head screwdriver to lift the locking

tab, twisting and removing from blower housing outlet.

 Unzip the vacuum bag and push the vacuum bag adaptor

through the opening opposite the zipper as shown. The

wider end of the adaptor will remain on the inside of the

vacuum bag when installed properly.

 Align the raised slots on the vacuum bag adaptor with the

raised locking tabs on the blower housing outlet. Push

the vacuum bag adaptor onto the housing and twist to

lock into place.



Rotate the vacuum bag until the shoulder strap is upright.

 Make sure the vacuum bag is zipped and closed before

starting the unit.

INSTALLING THE VACUUM TUBES

See Figures 7 - 8.

WARNING:

Contact with rotating impeller blades could result in seri-

ous personal injury. Always stop the engine and ensure

impeller blades have stopped rotating before opening

the vacuum door or installing/changing tubes. Do not put

hands or any other object into the vacuum tubes while

they are installed on the unit.

To install the vacuum tubes:

 Secure the upper and lower vacuum tubes together by

aligning the raised locking tabs with the raised slots.

 Tap tube assembly on ground until the screw holes in

lower tube are in the raised slot of the upper tube. Secure

with supplied screws.

 Depress door tab using a flathead screwdriver and open

vacuum inlet door.

 Align screw mounts on vacuum opening with screws on

vacuum tube assembly.

 Turning clockwise, tighten screws on upper vacuum tube

to secure to blower housing.

To remove the vacuum tubes:

 Loosen screws of the upper vacuum tube by turning

counterclockwise.

 Remove the vacuum tube assembly from the blower

housing.

 Close the vacuum inlet cover door securely.

 Remove the vacuum bag by using a flat head screwdriver

to lift the locking tab, rotate to unlock the adaptor and

remove.

ASSEMBLY

Page 8 — English

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Verify that all guards and tubes are in place prior to use.

If the blower is dropped, stop blower and verify that

no damage has occurred. If any guard, part, or tube is

damaged or missing, do not use blower until it has been

repaired or replaced by a qualified service center. Use of

blower with damaged or missing guards, parts, or tubes

can result in serious personal injury or further damage

to the blower.

NOTICE:

The spark arrestor on this product has not been evalu-

ated by the USDA Forest Service and cannot be used on

U.S. forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center to purchase a re-

placement spark arrestor.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced. Please contact customer service or a qualified

service center for assistance.

APPLICATIONS

You may use this product for the purposes listed below:

 Clearing leaves and other debris from your lawn

 Keeping decks and driveways free from leaves and other

forms of debris

 Vacuuming leaves from your lawn

ETHANOL-BLENDED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It is a viola-

tion of federal law and will damage the unit and void

your warranty. Only use unleaded gasoline containing

up to 10% ethanol.

NOTE: To improve performance when using oxygenated

fuels, we recommend the use of Ethanol Shield 2-cycle

lubricant.

FUELING AND REFUELING

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle it with care. Keep away from ignition

sources and open flames, handle outdoors only, do not

smoke, and wipe up spills immediately.

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certified to operate on

unleaded gasoline intended for automotive use.

NOTE: We recommend you use Ethanol Shield 2-cycle

lubricant, PowerCare 2-cycle lubricant, or an equivalent

high-quality synthetic 2-cycle lubricant in this product. Mix

at 2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

OPERATION

Page 9 — English

OPERATION

FILLING THE TANK

 Clean the surface around the fuel cap to prevent con-

tamination.

 Loosen the fuel cap slowly by turning counterclockwise.

 Pour the fuel mixture carefully into the tank.

 Clean and inspect the fuel cap gasket before replacing

the fuel cap.

 Replace the fuel cap and tighten it by turning it clockwise.

 Wipe spilled fuel from the product.

 Move at least 30 ft. away from refueling area before start-

ing the product.

NOTE: It is normal for smoke to be emitted from a new

engine during first use.

WARNING:

Always shut off engine before fueling. Never remove fuel

cap or add fuel to a machine with a running or hot engine.

Make sure the unit is sitting on a flat, level surface and

only add fuel outdoors. If the engine is hot, let the unit cool

for at least five minutes before adding fuel. After fueling,

immediately replace fuel cap and tighten securely. Move

at least 30 ft. from refueling site before starting engine. Do

not smoke and stay away from open flames and sparks!

Failure to follow these instructions could result in a fire

and cause serious personal injury.

STARTING AND STOPPING

See Figure 9.

Blower should be on a flat, bare surface for starting.

 Slowly press the primer bulb 10 times.

NOTE: After the 10th press, fuel should be visible in the

primer bulb. If it is not, continue to press the primer until

you see fuel in the bulb.

 Set the choke lever to the FULL CHOKE position.

 Lock cruise control lever/throttle lock to the full throttle

position.

 Pull starter grip and rope sharply until engine attempts to

run. Do not pull the starter grip and rope more than four

(4) times.

 Set the choke lever to the HALF CHOKE position.

 Pull the starter grip and rope until the engine runs.

NOTE: If the engine does not start, return to the FULL

CHOKE position and repeat the steps that follow.

 Allow the engine to run for 15 seconds, then set the choke

lever to the RUN position.

TO STOP THE ENGINE:

 To stop the engine, depress and hold the STOP switch

to the stop position “ ”.

HOT RESTART OF THE ENGINE:

 Set the choke lever to the RUN position.

 Lock cruise control lever/throttle lock.

 Pull the starter grip and rope until the engine runs.

IF ASSISTANCE IS REQUIRED STARTING THIS

PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE BLOWER

See Figures 10 - 11.

WARNING:

Never run the unit without the blower tubes installed and

the vacuum door securely closed. Use of an improperly

assembled unit could result in serious personal injury.

NOTICE:

Always operate your product in compliance with all

applicable laws and ordinances.

 Start the blower. Refer to Starting and Stopping earlier

in this manual. Hold the blower with the upper handle in

your right hand.

WARNING:

Always hold the blower away from your body with the

handle in your right hand when operating as a blower,

keeping clearance between your body and the product.

The muffler side of the blower should be away from your

body. Any contact with the housing can result in burns

and/or other serious personal injury.

WARNING:

Do not place blower on top of or near loose debris or

gravel. Debris may be sucked into blower intake vent

resulting in possible damage to the unit and could result

in serious personal injury.

 To keep from scattering debris, blow around the outer

edges of a debris pile. Never blow directly into the center

of a pile.

 Operate power equipment at reasonable hours only - not

early in the morning or late at night when people might be

disturbed. Comply with the times listed in local ordinances.

 To reduce sound levels, limit the number of pieces of

equipment used at any one time.

Page 10 — English

 Conserve water by using power blowers instead of hoses

for many lawn and garden applications, including areas

such as gutters, screens, patios, grills, porches, and

gardens.

 Operate blower at the lowest possible throttle speed to

do the job.

 Check your equipment before operation, especially the

muffler, air intakes, and air filters.

 Use rakes and brooms to loosen debris before blowing.

 In dusty conditions, slightly dampen surfaces when water

is available.

 Watch out for children, pets, open windows, or freshly

washed cars, and blow debris safely away.

 Hold blower, as shown in Figure 10, so the air stream can

work close to the ground.

 After using blowers or other equipment, CLEAN UP!

Dispose of debris properly.

 Use the sweeper nozzle for the everyday blowing opera-

tion. This nozzle allows for more area to be covered during

the blowing operation.

CRUISE CONTROL LEVER/THROTTLE LOCK

See Figure 12.

The cruise control lever/throttle lock can be used to operate

the blower without holding the throttle trigger.

 To engage, pull cruise control lever/throttle lock back

towards user, and stop at the desired throttle setting.

 To release, push cruise control lever/throttle lock all the

way towards the front of unit.

VACUUM OPERATION

See Figure 13.

WARNING:

Never run the unit without the vacuum tubes and vacuum

bag installed. Use of an improperly assembled unit could

result in serious personal injury.

WARNING:

Keep the muffler and all hot surfaces of the blower/

vacuum away from your body. Failure to do so could

result in possible serious personal injury.

 Install the vacuum tubes and the bag. Refer to the

Assembly section earlier in this manual.

 Start the blower. Refer to Starting and Stopping earlier

in this manual.

 Place the vacuum bag strap over your right shoulder.

Hold the upper handle in your left hand and the vacuum

handle in your right hand.

 Move the blower/vacuum from side to side along outer

edge of the debris. To avoid clogging, do not place the

vacuum tube directly into the debris pile.

 Hold the engine higher than the inlet end of the vacuum

tube.

 Always point vacuum tube downhill when working on a

hillside.

 To avoid serious injury to the operator or damage to the

unit, do not pick up rocks, metal, broken glass, bottles,

or other similar objects.

 If the vacuum tubes should clog, stop the engine , ensure

impeller blades have stopped spinning, and disconnect

the spark plug wire before cleaning out the obstruction.

 Remove the vacuum tubes and clear the debris from the

blower fan housing. Remove the bag and clear the tube.

A small rod or stick may be required to clear the entire

tube length. Ensure that all debris has been cleared before

reassembling the vacuum tubes.

OPERATION

Page 11 — English

Normal maintenance, replacement or repair of emission con-

trol devices and systems may be performed by any qualified

repair establishment or individual with original or equivalent

parts. Warranty and recall repairs must be performed by an

authorized service center; please contact customer service

for assistance.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

When servicing, use only recommended or equivalent

replacement parts. Use of any other parts could create

a hazard or cause product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced. Please contact customer service or a qualified

service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal injury.

CLEANING THE AIR FILTER

See Figure 14 - 15.

For proper performance and long life, keep air filter clean.

 Remove the air filter cover by turning the dial counter-

clockwise while gently pulling on the cover.

 Rinse filter with clean water.

 Gently squeeze filter until excess water is removed.

Replace filter.

 Place the air filter cover back on the unit. Turn dial clock-

wise until cover is secure.

CLEANING THE EXHAUST PORT, MUFFLER

AND SPARK ARRESTOR

NOTICE:

The spark arrestor on this product has not been evalu-

ated by the USDA Forest Service and cannot be used on

U.S. forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center to purchase a re-

placement spark arrestor.

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recommend

that only qualified service technicians perform this service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact customer service

or a qualified service center for assistance.

WARNING:

Never run the blower without a muffler equipped with a

spark arrestor in place. Failure to do so could result in a

fire that could cause serious personal injury.

VACUUM BAG

A dirty bag will reduce performance. To clean the bag, turn it

inside out and shake. Wash the bag in soapy water at least

once a year. To obtain a replacement bag, see How to Ob-

tain Replacement Parts on the back page of this manual.

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or line is a

fire hazard and must be replaced immediately. If you find

any leaks, correct the problem before using the product.

Failure to do so could result in a fire that could cause

serious personal injury.

The fuel cap contains a non-serviceable filter and a

check valve. A clogged fuel filter will cause poor engine

MAINTENANCE

Page 12 — English

performance. If performance improves when the fuel cap

is loosened, check valve may be faulty or filter clogged.

Replace fuel cap if required.

SPARK PLUG REPLACEMENT

This engine uses a Ryobi AC00160A, Champion RCJ-6Y,

or equivalent spark plug with .025 in. electrode gap. Use

a recommended or equivalent replacement and replace

annually.

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Your engine is configured for operation below 2,000 feet

altitude at the factory. Your engine must be reconfigured for

operation above 2,000 feet altitude. Operating the engine

with the wrong engine configuration at a given altitude may

increase its emissions, decrease fuel efficiency, degrade

performance, and cause irreversible damage. Engines

configured for high altitude operation cannot be operated

in standard altitude conditions. A qualified service center

should ensure that your engine is properly configured for

your location.

MAINTENANCE

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

MAINTENANCE SCHEDULE

Inspect for Clean Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 50 Hours

* CATALYTIC MUFFLER ASSEMBLY ..........................................................................................................................X

SPARK SCREEN ........................................................................................................................................................X

* AIR FILTER ASSY

includes:

Filter ..........................................................................................X

* CARBURETOR ASSY

includes:

Gaskets ........................................... X

* FUEL TANK ASSY

includes:

Fuel Lines........................................ X

Fuel Cap ......................................... X

Fuel Filter ..........................................................................................................................X

* IGNITION ASSY

includes:

Spark Plug ........................................................................................................................X

* NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT

IS A VIOLATION OF FEDERAL LAW.

Page 13 — English

PROBLEM POSSIBLE CAUSE REMEDY

Engine fails to start. No fuel in tank.

Spark plug shorted or fouled.

Spark plug is broken. (cracked

porcelain or electrodes broken)

Ignition lead wire shorted, broken, or

disconnected from spark plug.

Ignition inoperative.

Fill tank.

Replace spark plug.

Replace lead wire or attach to spark

plug.

Contact a qualfied service center.

Engine hard to start. Water in gasoline or stale fuel mixture.

Too much lubricant in fuel mixture.

Engine is under or over choked.

Weak spark at spark plug.

Drain entire system and refill with fresh

fuel.

Drain and refill with correct mixture.

Adjust choke as necessary.

Contact a qualfied service center.

Engine lacks power. Air filter clogged. Clean air filter. Refer to Cleaning the

Air Filter earlier in this manual.

Engine overheats. Insufficient lubricant in fuel mixture. Mix fuel as described in starting

instructions.

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the Maintenance

section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing

to perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause

irreversible engine damage and/or void your warranty.

TROUBLESHOOTING

Page 14 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Homelite Consumer Products, Inc., (“Homelite”) warrants

to the original retail purchaser that this HOMELITE brand

outdoor product is free from defect in material and

workmanship and agrees to repair or replace, at Homelite’s,

discretion, any defective product free of charge within these

time periods from the date of purchase.

 Two years if the product is used for personal, family or

household use;

 90 days for any unit used for other purposes, such as

rental or commercial.

This warranty extends to the original retail purchaser only

and commences on the date of the original retail purchase.

Any part of the this product manufactured or supplied

by Homelite and found in the reasonable judgment of

Homelite to be defective in material or workmanship will

be repaired or replaced without charge for parts and labor

by a Homelite authorized service center.

The product, including any defective part, must be returned

to an authorized service dealer within the warranty period.

The expense of delivering the product to the dealer for

warranty work and the expense of returning it back to the

owner after repair or replacement will be paid by the owner.

Homelite’s responsibility in respect to claims is limited to

making the required repairs or replacements and no claim

of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any HOMELITE brand

product. Proof of purchase will be required by the dealer

to substantiate any warranty claim. All warranty work must

be performed by a Homelite authorized service center.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any HOMELITE brand product

that is used for rental or commercial purposes, or any other

income-producing purpose.

This warranty does not cover any HOMELITE brand product

that has been subject to misuse, neglect, negligence, or

accident, or that has been operated in any way contrary

to the operating instructions as specified in this operator’s

manual. This warranty does not apply to any damage to

the product that is the result of improper maintenance or

to any product that has been altered or modified. The

warranty does not extend to repairs made necessary

by normal wear or by the use of parts or accessories

which are either incompatible with the HOMELITE

brand product or adversely affect its operation,

performance, or durability. In addition, this warranty does

not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bags

and Straps, Guide Bars, Saw Chains, Blades

Homelite reserves the right to change or improve the design

of any HOMELITE brand product without assuming any

obligation to modify any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN

THEIR ENTIRETY AFTER THE EXPIRATION OF THE

APPROPRIATE TWO-YEAR OR NINETY-DAY WARRANTY

PERIOD. HOMELITE’S OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED

TO THE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS AND HOMELITE DOES NOT ASSUME OR

AUTHORIZE ANYONE TO ASSUME FOR THEM ANY

OTHER OBLIGATION. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY

TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY

FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER

DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE

OF RETURNING THE PRODUCT TO AN AUTHORIZED

HOMELITE SERVICE CENTER AND EXPENSE OF

DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all HOMELITE brand products

manufactured by or for Homelite and sold in the United

States and Canada.

To locate your nearest Homelite authorized service

center, dial 1-800-242-4672 or log on to our website at

www.homelite.com.

Page 3 — Français

AVERTISSEMENT :

LIRE ET VEILLER À BIEN COMPRENDRE TOUTES

LES INSTRUCTIONS. Le non respect de toutes les

instructions ci-dessous peut entraîner un choc électrique,

un incendie et / ou des blessures graves.

LIRE TOUTES LES INSTRUCTIONS

Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

Ne pas démarrer ou faire tourner le moteur dans un

espace confine, de bâtiment, à proximité des fenêtres

ouverts, autre ou des zones sans ventilation où des

vapeurs toxiques de monoxyde de carbone peuvent

s’accumuler. Le monoxyde de carbone, un gaz incolore,

inodore et extrêmement toxique peut causer une perte

de conscience et être mortel.

Toujours porter une protection oculaire avec écrans

latéraux certifiée conforme à la norme ANSI Z87.1, avec

protection auditive. Si cette précaution n’est pas prise,

des objets peuvent être projetés dans les yeux et d’autres

lésions graves.

Garder tous les badauds, enfants et animaux domestiques

à une distance d’au moins 15 m (50 pi).

Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, shorts, sandales, bijoux quels qu’ils

soient et ne pas travailler pieds nus.

Pour réduire les risques de happement par les pièces

en mouvement, ne pas porter de vêtements amples,

foulards, colliers, etc.

Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les pièces

en rotation.

Ne pas utiliser cet outil en état de fatigue, si l’on est

souffrant ou sous l’influence de l’alcool, de drogues ou

de médicaments.

Ne pas travailler sous un éclairage insuffisant.

Garder toutes les parties du corps à l’écart des pièces

en mouvement et des paries brûlantes de l’outil.

Porter un masque facial filtrant dans les milieux

poussiéreux afin de réduire le risque de lésions lié à

l’inhalation de poussière.

Examiner la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre

brisé, clous, fils métalliques, cordes, etc. risquant d’être

projetés ou de se prendre dans la machine.

Se tenir bien campé et en équilibre. Ne pas travailler

hors de portée. Le travail hors de portée risque de faire

perdre l’équilibre ou de causer un contact avec les

pièces brûlantes.

Laisser le moteur refroidir avant de remiser l’outil.

Vider le réservoir de carburant dans un contenant

approuvé pour l’essence et immobiliser l’unité avant de

la transporter dans un véhicule.

Manipuler le carburant avec précaution pour éviter les

risques d’incendies et de brûlures. Le carburant est

extrêmement inflammable.

Ne pas fumer pendant la manipulation du carburant.

Mélanger et conserver le carburant dans un bidon ou

jerrican approuvé pour l’essence.

Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles.

Poser la machine sur un sol nu, arrêter le moteur et le

laisser refroidir avant de faire le plein.

Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant s’échappe.

Une fois le réservoir plein, remettre le bouchon en place

et le serrer fermement.

Essuyer tout le carburant éventuellement répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur.

N’essayer en aucun cas de brûler le carburant répandu.

Utiliser exclusivement des pièces de rechange et

accessoire recommandées ou équivalentes. L’usage de

toute autre pièce pourrait créer une situation dangereuse

ou endommager l’outil.

Entretenir l’outil conformément aux instructions de ce

manuel d’utilisation.

Inspecter l’outil avant chaque utilisation pour s’assurer

qu’il n’y a pas de pièces desserrées, de fuites ce

carburant, etc. Remplacer les pièces endommagées.

Ne pas utiliser l’unité sur une échelle, un toit, un arbre ou

un autre support instable. Le fait de se tenir bien campé

sur une surface solide permet de mieux contrôler la

soufflante dans des situations inattendues.

Avant de nettoyer, réparer ou inspecter, arrêter le moteur

et vérifier que toutes les pièces en mouvement sont

immobilisées. Déconnecter le fil de bougie et le garder

à l’écart de la bougie afin d’empêcher un démarrage

accidentel.

Il est recommandé d’apporter la équipement à un

centre de réparations qualifié pour la faire réparer pour

éviter que des réparations effectuées par une personne

inexpérimentée ou non qualifiée puissent endommager

la équipement, créer des conditions dangereuses, des

blessures à l’utilisateur et annuler la garantie.

RÈGLES DE SÉCURITÉ GÉNÉRALES

Page 4 — Français

Toujours tenir la soufflante / aspirateur avec la main

droite pendant le soufflage. Consulter les instructions

d’Utilisation présentées ultérieurement dans ce manuel afin

de connaître la position adéquate pour utiliser l’aspirateur,

et obtenir des renseignements supplémentaires.

Ne jamais rien insérer dans les tubes.

Utiliser exclusivement selon les instructions de ce manuel.

Ne pas utiliser l’aspirateur sans le sac, car des débris

pourraient être projetés et infliger des blessures graves.

Toujours fermer le sac complètement avant d’utiliser

l’aspirateur.

L’aubage de la roue en rotation peut entraîner des

blessures graves. Arrêter le moteur et s’assurer que

l’aubage de la roue a cessé de tourner avant d’ouvrir la

porte de l’aspirateur ou d’installer ou de changer les tuyaux.

Ne pas mettre les mains ou quelque objet que ce soit dans

les tubes installés sur la machine.

Ne jamais utiliser la soufflante sans les accessoires

appropriés installés. Les tubes de soufflante doivent

toujours être installés lorsque la machine est utilisée en

soufflante. Lorsque la machine est utilisée pour aspirer,

les tubes d’aspiration et le sac doivent toujours être

installés. Pour éviter la projection de débris, s’assurer que

la fermeture à glissière de sac est complètement fermée

lorsque le moteur tourne.

Éviter les situations pouvant mettre le feu au sac. Ne pas

utiliser la machine à proximité de flammes vives. Ne pas

aspirer les cendres chaudes de cheminées, barbecues,

feux de bois, etc. Ne pas aspirer de mégots de cigares

ou cigarettes dont les cendres ne sont pas complètement

froides.

 Ne jamais placer la soufflante en marche sur une surface,

sauf si celle-ci est dure et propre. Le gravier, le sable et

les autres débris peuvent être aspirés dans l’entrée d’air

et projetés en direction de l’utilisateur ou des personnes

à proximité, ce qui peut entraîner des blessures graves.

 Pour réduire les risques de perte de l’ouïe causée par le

niveau sonore, porter une protection auditive.

 Pour réduire les risques de blessures infligées par des

pièces en rotation, arrêter le moteur avant d’installer ou

de retirer des accessoires. Toujours débrancher le fil de

bougie avant de procéder à un entretien ou d’accéder à

des pièces en mouvement.

 Ne jamais utiliser la soufflante à proximité d’un feu, d’un

poêle, de cendres chaudes, d’un barbecue, etc., sans quoi

le feu risque de se propager.

 Ne pas diriger la soufflante vers des personnes ou un

animaux.

Ce produit est conçu pour les personnes qui prévoient

l’utiliser de manière peu fréquente pour des applications

générales par exemple, souffler les feuilles et les brins

d’herbe, etc.; l’outil peut également convenir à d’autres

utilisateurs occasionnels. Elle n’est pas conçue pour un

usage prolongé. Les périodes d’utilisation prolongée

peuvent entraîner des problèmes circulatoires dans les

mains de l’opérateur, causés par les vibrations. Pour ce type

d’application, il peut être bon d’utiliser une scie équipée

d’un dispositif anti-vibrations.

APPROVISIONNEMENT EN CARBURANT

Le carburant est extrêmement inflammable. Lors de

l’utilisation, prendre les précautions nécessaires pour

réduire le risque de blessures graves.

Conserver le carburant dans une zone froide bien ventilée

à l’écart d’étincelles et / ou de matériels produisant des

flammes.

Conserver le carburant dans des jerrycans spécialement

conçus à cet effet.

Toujours faire le plein à l’extérieur et ne pas fumer pendant

cette opération.

Faire l’appoint de carburant avant de lancer le moteur. Ne

jamais retirer le bouchon du réservoir de carburant ni faire

l’appoint pendant que le moteur tourne ou est chaud.

Ne pas fumer pendant la manipulation du carburant.

Mélanger et conserver le carburant dans un bidon ou

jerrycan approuvé pour l’essence.

Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles.

Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant s’échappe.

Une fois le réservoir plein, remettre le bouchon en place

et le serrer fermement.

Essuyer tout le carburant éventuellement répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur.

N’essayer en aucun cas de brûler le carburant répandu.

Manipuler le carburant avec précaution pour éviter les

risques d’incendies et de brûlures. Le carburant est

extrêmement inflammable.

Si du carburant est répandu, ne pas essayer de lancer le

moteur, mais éloigner la machine et éviter de créer une

source d’inflammation jusqu’à ce que les vapeurs de

carburant se soient dissipées.

Remettre en place les bouchons de jerrycan et de réservoir

de carburant et les serrer fermement.

Vider le réservoir de carburant dans un contenant approuvé

pour l’essence et empêcher l’unité de bouger avant de le

transporter dans un véhicule.

Lors de la vidange du réservoir de carburant, utiliser

un bidon ou jerrycan approuvé pour la conservation de

carburant et procéder dans un endroit bien aéré.

Poser la machine sur un sol nu, arrêter le moteur et le laisser

refroidir avant de faire le plein.

Conserver ces instructions. Les consulter fréquemment et

les utiliser pour instruire les autres utilisateurs éventuels.

Si cet outil est prêté, il doit être accompagné de ces

instructions.

RÈGLES DE SÉCURITÉ PARTICULIÈRES

La page charge ...

Homelite UT26HBV Mode d'emploi

Marque: Homelite

Modèle: UT26HBV

Catégorie: Souffleurs / sécheurs d'air

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Homelite UT26HBV User guide
español: Homelite UT26HBV Guía del usuario

Homelite UT26HBV Mode d'emploi

Homelite UT26HBV Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents