Hatco C-7-208-3 Manuel utilisateur

Marque: Hatco

Modèle: C-7-208-3

Taper: Manuel utilisateur

Electric Booster Water Heaters

Réchauffeurs d’eau électriques

Imperial, Compact, and Mini-Compact

Series/Série

Installation and Operating Manual

Manuel d’installation et d’utilisation

Ne pas utiliser cet équipement sans avoir

lu et compris le contenu de ce manuel ! Le

non-respect des instructions contenues

dans ce manuel peut entraîner de

graves blessures ou la mort. Ce manuel

contient des informations importantes

concernant l’entretien, l’utilisation et le

fonctionnement de ce produit. Si vous ne

comprenez pas le contenu de ce manuel,

veuillez le signaler à votre supérieur.

Conservez ce manuel dans un endroit

sûr pour pouvoir vous y référer plus tard.

Français = p 26

AVERTISSEMENT

hatcocorp.com

(see page 2)

S’inscrire en ligne!

(voir page 26)

Do not operate this equipment unless you

have read and understood the contents

of this manual! Failure to follow the

instructions contained in this manual

may result in serious injury or death.

This manual contains important safety

information concerning the maintenance,

use, and operation of this product. If

you’re unable to understand the contents

of this manual, please bring it to the

attention of your supervisor. Keep this

manual in a safe location for future

reference.

English = p 2

WARNING

No opere este equipo al menos que haya

leído y comprendido el contenido de este

manual! Cualquier falla en el seguimiento

de las instrucciones contenidas en

este manual puede resultar en un serio

lesión o muerte. Este manual contiene

importante información sobre seguridad

concerniente al mantenimiento, uso y

operación de este producto. Si usted

no puede entender el contenido de

este manual por favor pregunte a su

supervisor. Almacenar este manual en

una localización segura para la referencia

futura.

ADVERTENCIA

Form No. EBOOSTERM-0321

English

INTRODUCTION

Hatco Electric Booster Water Heaters are designed

for use with commercial dish machines to boost the temperature

of the regularly available hot water, usually 115°–150°F

(46°–66°C) up to 180°F (82°C). Water at 180°F (82°C) can be

used as sanitizing rinse water in commercial dish machines in

accordance with Health Codes, NSF Standard #5 and plumbing

codes.

All Hatco Booster Heaters are ready for electrical and plumbing

service connections, with an adjustable ambient compensated

immersion thermostat(s) and a high temperature limit switch.

The service area is accessible from the front of the unit,

permitting easy access.

Hatco Electric Booster Water Heaters are products of extensive

research and field testing. The materials used were selected

for maximum durability, attractive appearance, and optimum

performance. Every unit is inspected and tested thoroughly

prior to shipment.

This manual provides the installation, safety, and operating

instructions for the Hatco Electric Booster Water Heaters. Hatco

recommends all installation, operating, and safety instructions

appearing in this manual be read prior to installation or

operation of the unit.

Safety information that appears in this manual is identified by

the following signal word panels:

WARNING

WARNING indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to

personal injury.

Important Owner Information ..............................................2

Introduction ...........................................................................2

Important Safety Information ..............................................3

Model Description ................................................................5

All Models ............................................................................ 5

Imperial Models “S” Series .................................................. 5

Compact Models “C” Series ................................................5

Mini-Compact Models “MC” Series .....................................5

Specifications .......................................................................6

Booster Heater Sizing Chart ................................................6

Circuit Breaker and Fused Disconnect Switch Sizes ..........7

Dimensions ........................................................................ 10

Installation ...........................................................................12

General .............................................................................. 12

Plumbing Installation .........................................................13

Electrical-All Sizes and Voltages ....................................... 18

Operation .............................................................................19

General .............................................................................. 19

Maintenance ........................................................................20

General .............................................................................. 20

Thermostat Adjustment ......................................................20

High Temperature Limit Safety Switch ..............................20

Troubleshooting Guide ......................................................21

Options and Accessories ..................................................24

Limited Warranty ................................................................25

Authorized Parts Distributors ...........................Back Cover

IMPORTANT OWNER INFORMATION

Record the model number, serial number, voltage, and purchase

date of the unit in the spaces below (specification label located

on the unit). Please have this information available when calling

Hatco for service assistance.

Model No. _______________________________________

Serial No. ________________________________________

Voltage __________________________________________

Date of Purchase __________________________________

Completing online warranty registration will prevent delay in

obtaining warranty coverage. Access the Hatco website at

www.hatcocorp.com, select the Support pull-down menu,

and click on “Warranty”.

Business

Hours: 7:00  to 5:00  Monday–Friday,

Central Time (CT)

(Summer Hours — June to September:

7:00  to 5:00  Monday–Thursday

7:00  to 4:00  Friday)

Telephone: 800-558-0607; 414-671-6350

E-mail: [email protected]

24 Hour 7 Day Parts and Service

Assistance available in the United States

and Canada by calling 800-558-0607.

Additional information can be found by visiting our web site at

www.hatcocorp.com.

CONTENTS

Form No. EBOOSTERM-0321 3

English IMPORTANT SAFETY INFORMATION

WARNING

ELECTRIC SHOCK HAZARD:

• Unit must be installed by qualified, trained installers.

Installation must conform to all local electrical and

plumbing codes. Installation by unqualified personnel

will void the unit warranty and may lead to electric

shock or burn, as well as damage to unit and/or its

surroundings. Check with local plumbing and electrical

inspectors for proper procedures and codes.

• Turn OFF power at fused disconnect switch/circuit

breaker and allow unit to cool before performing any

cleaning, adjustments, or maintenance.

• Consult a licensed electrical contractor for proper

electrical installation conforming to local electrical

codes and the National Electrical Code (N.E.C.).

• Unit is not weatherproof. Locate unit indoors where

ambient air temperature is a minimum of 70°F (21°C).

• Do not place aftermarket covers on or over booster

heater. Doing so can cause temperature and moisture

build-up resulting in premature failure and electrical

shock.

• This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric

shock or burn.

• Use only Genuine Hatco Replacement Parts when

service is required. Failure to use Genuine Hatco

Replacement Parts will void all warranties and may

subject operators of the equipment to hazardous

electrical voltage, resulting in electrical shock or burn.

Genuine Hatco Replacement Parts are specified to

operate safely in the environments in which they are

used. Some aftermarket or generic replacement parts

do not have the characteristics that will allow them to

operate safely in Hatco equipment.

Valves supplied by Hatco are designed for high-temperature

commercial operation. Do not substitute Hatco valves with

valves designed for domestic water heaters.

Temperature/pressure protective equipment should not be

less than a combination temperature/pressure relief valve

certified by a nationally recognized testing laboratory that

maintains periodic inspection of the production of this

equipment and meets the requirements for Relief Valves

and Automatic Shutoff Devices for Hot Water Supply

Systems, ANSI Z21.22-1979. The temperature/pressure

relief valve must be marked with a minimum set pressure

not to exceed the marked hydrostatic test pressure of the

booster heater as noted on the unit specifications.

EXPLOSION HAZARD: Do not store or use gasoline or

other flammable vapors or liquids in the vicinity of this or

any other appliance.

WARNING

FOR INSTALLING PRESSURE AND TEMPERATURE

RELIEF VALVES IN ACCORDANCE WITH AMERICAN

NATIONAL STD. Z21.22-1979. Combination pressure and

temperature relief valves with extension thermostats must

be installed so that the temperature-sensing element is

immersed in the water within the top 6″ (152 mm) of the

tank. They must be installed directly in a tank tapping.

Combination pressure and temperature relief valves that

do not have extension elements must be mounted directly

in a tank tapping located within the top 6″ (152 mm) of the

tank, and shall be adequately insulated and located so as

to assure isolation from ambient conditions that are not

indicative of stored water temperature. TO AVOID WATER

DAMAGE OR SCALDING DUE TO VALVE OPERATION,

DRAIN PIPE MUST BE CONNECTED TO VALVE OUTLET

AND RUN TO A SAFE PLACE OF DISPOSAL. Discharge

line must be as short as possible and be the same size

as the valve discharge connection throughout its entire

length. Drain line must pitch downward from the valve and

must terminate between 1-1/2″ (38 mm) and 6″ (152 mm)

above the floor drain where any discharge will be clearly

visible. The drain line shall terminate plain, not threaded,

with material serviceable for temperatures up to 250°F

(121°C) or greater. Excessive length, over 30' (9.1 m), or

use of more than four elbows can cause a restriction and

reduce the discharge capacity of the valve. No shut-off

valve shall be installed between the relief valve and tank, or

in the drain line. Valve lever must be tripped periodically to

assure that waterways are clear. This device is designated

for emergency safety relief and shall not be used as an

operating control. The valves are set to relieve at 150 psi

(1034 kPa) or when water temperature reaches 210°F

(99°C). Read tag on valve for additional information.

Use only copper plumbing material. Non-copper plumbing

material may create an unsafe condition.

Units are equipped with a high temperature limit safety

switch that will shut off the power if the unit overheats.

Contact an Authorized Hatco Service Agent if the high

temperature limit safety switch cannot be reset or

continues to trip.

Install booster water heater in a horizontal position with

the base parallel to the floor and the inlet connection at the

lowest point. Improper installation could create an unsafe

condition.

Do not connect booster water heaters to domestic

(consumer) dish machines or other domestic utilized

equipment. This booster may damage domestic equipment.

Read the following important safety information before using this equipment to avoid serious

injury or death and to avoid damage to equipment or property.

Form No. EBOOSTERM-0321

English

IMPORTANT SAFETY INFORMATION

WARNING

This product contains fiberglass, a product known to the

state of California to cause cancer, birth defects, or other

reproductive harm.

Install booster water heater as close as possible to

a commercial dish machine. Employ re-circulation if

distance between water heater and dish machine exceeds

National Sanitation Foundation (NSF) specifications of five

(5) linear feet (1524 mm).

Follow standard welding safety and operational procedures

when attaching sliderails to bottom of dishtable.

Make sure the dishtable is strong enough to support the

weight of the heater AND water when installing with slide

mounting brackets.

Refer to the BOOSTER HEATER SIZING CHART in this

manual to ensure proper sizing and avoid personal injury

and/or damage to the booster heater.

It is essential to recognize that even though a water heater

may be properly installed initially and approved, there

always exists the possibility that unknowing individuals

might alter or change the installation in a manner that

would render it unsafe. Therefore, it is important that all

safety programs provide some mechanism to assure that

these installations are inspected periodically.

This unit has no “user-serviceable” parts. If service

is required on this unit, contact an Authorized Hatco

Service Agent or contact the Hatco Service Department at

800-558-0607 or 414-671-6350.

CAUTION

BURN HAZARD:

• Water in unit is very hot. Wear protective gloves and

proper attire when operating to avoid injury.

• Valves supplied by Hatco are designed for high

temperature commercial operation. Do not substitute

Hatco valves with valves designed for domestic water

heaters.

Do not use anti-siphon valves on incoming water line.

Check valves on incoming water line is not recommended.

Damages caused by the use of check valves on unit will

not be covered by warranty.

Do not connect booster heater directly to a boiler or

furnace coil or any other uncontrolled temperature source.

The booster heater thermostat could be damaged causing

unit to overheat.

Incoming water temperature should be minimum of 85°F

(29°C). Damage to the heater can occur if water is cooler

than 85°F (29°C).

CAUTION

Hatco requires that two temperature/pressure gauges

(Hatco P/N 03.01.003.00) be installed to ensure proper

operation. Install one in the supply line before the pressure

reducing valve and one in the outlet line as close to the

booster heater as possible. This provides a visual check

of the water temperature and pressure before and after the

water heater.

If water supply pressure to the booster inlet is over

20 psi (138 kPa) during flow, install pressure reducing

valve with built-in bypass (Hatco P/N 03.02.004.00) for

proper operation of dish machine rinse nozzles.

NOTE: The pressure reducing valve must be the type equipped

with a high pressure bypass, as supplied by Hatco.

DO NOT turn on power to the booster heater until tank has

been filled with water and all air has been vented through

the dish machine rinse nozzles. Heating elements will burn

out in seconds if operated when not immersed in water.

NOTICE

Always drain booster heater with power to the unit off or

element burnout could occur.

Use dielectric couplings when connecting dissimilar

metals, such as galvanized to copper. This will prevent

electrolysis or premature plumbing damage.

Do not turn or adjust outlet water connection on all Large

Compact Series units (C-24 to C-57).

Do not turn or adjust inlet or outlet water connection on

Compact Series Booster Heaters or internal water flow will

change and the unit will not produce a consistent outlet

temperature.

Do not back out or loosen any pipe fittings or leaks may

occur.

Do not lay unit on the side with the control panel or inlet

and outlet pipes. Damage to the unit could occur.

Incoming water in excess of 3 grains of hardness per

gallon (GPG) (0.75 grains of hardness per liter [GPL]) must

be treated and softened before being supplied to booster

heater(s). Water containing over 3 GPG (0.75 GPL) will

decrease efficiency, increase energy use, and reduce the

operating life of the unit through increased lime build-up.

Product failure caused by liming or sediment buildup is

not covered under warranty.

Do not use deionized water. Deionized water will shorten

the life of water reservoir and heating element.

Units are voltage-specific. Refer to specification label

for electrical requirements before beginning installation.

Connecting unit to incorrect power supply will void

product warranty and may damage unit.

Read the following important safety information before using this equipment to avoid serious

injury or death and to avoid damage to equipment or property.

Form No. EBOOSTERM-0321 5

English MODEL DESCRIPTION

All Models

Hatco Electric Water Booster Heaters are available in three

models: Imperial, Compact, and Mini-Compact. All standard

models include a booster heater with low-water cut-off system,

temperature/pressure relief valve, pressure reducing valve

with built-in high pressure bypass, two temperature/pressure

gauges, and a high temperature limit safety switch.

Imperial Models “S” Series

Hatco Imperial models feature a Castone® tank with a

10 year limited tank warranty, a Power I/O (on/off) switch, an

         

capacity of 16 gallons (61 liters) and provide up to 572 gallons

per hour (GPH) (2169 liters per hour [LPH]) of sanitizing rinse

water based on a 40°F (22°C) temperature rise.

Imperial Model

Compact Models “C” Series

Hatco Compact models feature a Castone® tank with a

10 year limited tank warranty, a Power I/O (on/off) switch, an



brackets for mounting under a dish table. Compact units have

a capacity of 6 gallons (23 liters) and provide up to 573 GPH

(2169 LPH) of sanitizing rinse water based on a 40°F (22°C)

temperature rise.

Compact Model

Mini-Compact Models “MC” Series

Hatco Mini-Compact models feature a stainless steel tank with



Compact units have a capacity of 3.2 gallons (12 liters) and

provide up to 172 GPH (655 LPH) of sanitizing rinse water

based on a 40°F (22°C) temperature rise. Ideal for either hot

water sanitizing or point-of-use hot water dispensing.

NOTE: Mini-Compact models can be configured with an

optional Power I/O (on/off) switch.

Mini-Compact Model

Form No. EBOOSTERM-0321

English

SPECIFICATIONS

Booster

Heater

Water Temperature Rise

Booster

Heater

30°F 40°F 50°F 60°F 70°F 80°F 90°F 100°F

GPH GPH GPH GPH GPH GPH GPH GPH

4 54 40 32 27 23 20 18 16 4

5 67 50 40 33 29 25 22 20 5

6 80 60 48 40 34 30 27 24 6

7 94 70 56 47 40 35 31 28 7

9 120 90 72 60 52 45 40 36 9

9.9 132 99 79 66 57 50 44 40 9.9

10.5 140 105 84 70 60 53 47 42 10.5

11.4 153 114 92 76 65 57 51 46 11.4

12 161 120 96 80 69 60 54 48 12

13.5 181 135 108 90 77 68 60 54 13.5

15 201 151 120 100 86 75 67 60 15

17.25 231 173 139 115 99 87 77 69 17.25

18 241 181 145 120 103 90 80 72 18

24 321 241 193 161 138 120 107 96 24

27 361 271 217 181 155 135 120 108 27

30 401 301 241 201 172 151 134 120 30

36 482 361 289 241 206 181 161 145 36

39 522 391 313 261 224 196 174 157 39

40.5 542 407 325 271 232 203 181 163 40.5

45 602 452 361 301 258 226 201 181 45

54 723 542 434 361 310 271 241 217 54

57 763 573 458 381 326 286 254 229 57

Booster Heater Sizing Chart

Use the table below or the “Booster Heater Sizing Formula” to determine what Booster Heater kW rating is needed with your

dishmachine.

1. Determine the water temperature rise.

a. Subtract the lowest incoming water temperature supplied to the Booster Heater from the desired output water temperature

of the Booster Heater. The difference is the Water Temperature Rise. Typically 145°F (63°C) is a low temperature chemical

sanitizing application and 185°F (85°C) is a high temperature heated water sanitizing application.

2. Follow the appropriate “Water Temperature Rise” column down and locate the Gallons Per Hour (GPH) of the dishmachine’s rinse

cycle (round up to the next size if exact GPH isn’t listed).

NOTE: The primary water heater must be able to supply the Booster Heater with the incoming water temperature at the GPH usage

of the dishmachine. Failure of the primary water heater to supply a continuous temperature will result in an inadequate

output temperature of the Booster Heater.

3. Follow the GPH row to either of the “Booster Heater kW” columns for the appropriate Booster Heater kW rating.

Example: An incoming water temperature of 115°F (46°C) with a desired output temperature of 185°F (85°C) would be a 70°F

(39°C) water temperature rise.

A 70°F (39°C) water temperature rise with a dishmachine capable of 185 GPH usage will require a minimum of a 36 kW

Booster Heater.

NOTE: When incoming water temperatures are less than 85°F (29°C), consult factory for suitable Booster Heater.

LPH x Water Temp. Rise

840 = kW

Booster Heater Sizing Formula NOTE: Refer to the “Water Temperature Rise” table in the French

section of this manual for the metric (Celsius and liters) version

of this table.

Form No. EBOOSTERM-0321 7

English SPECIFICATIONS

Circuit Breaker and Fused Disconnect Switch Sizes — 4 to 12 kW

The shaded area contains electrical information for International models only.

NOTE: 250 kcmil maximum wire size for terminal block.

kW Volts Phase

Amp Draw Breaker or

Fuse

Size

Copper Wire

Size Conduit SizeL1 L2 L3

4 208 1 19 19 -- 30 10 1/2

240 1 17 17 -- 30 10 1/2

480 1 8 8 -- 15 14 1/2

5 208 1 24 24 -- 30 10 1/2

240 1 21 21 -- 30 10 1/2

480 1 10 10 -- 15 14 1/2

6 208 1 29 29 -- 40 8 1/2

208 3 14 25 14 40 8 1/2

240 1 25 25 -- 40 8 1/2

240 3 13 22 13 30 10 1/2

380 3 9.2 9.2 9.2 15 14 1/2

480 3 6 11 6 15 14 1/2

600 3 5.7 5.7 5.7 15 14 1/2

7 208 1 34 34 -- 50 8 1/2

208 3 17 29 17 40 8 3/4

240 1 29 29 -- 40 8 1/2

240 3 15 25 15 40 8 1/2

380 3 11.4 11.4 11.4 15 14 1/2

480 3 7 13 7 20 12 1/2

600 3 6.7 6.7 6.7 15 14 1/2

9 208 1 43 43 -- 60 6 1/2

208 3 22 38 22 50 8 1/2

240 1 38 38 -- 50 8 1/2

240 3 19 33 19 50 8 1/2

380 3 13.3 13.3 13.3 20 12 1/2

480 3 9 16.3 9 30 12 1/2

600 3 8.7 8.7 8.7 15 14 1/2

9.9 208 1 47.5 47.5 -- 60 6 1/2

208 3 27.5 27.5 27.5 40 8 1/2

10.4 208 3 28.8 28.8 28.8 40 8 1/2

10.5 208 1 51 51 -- 70 4 3/4

208 3 29 29 29 40 8 1/2

240 1 44 44 -- 60 6 1/2

240 3 25.3 25.3 25.3 40 8 1/2

480 3 12.6 12.6 12.6 20 12 1/2

600 3 10 10 10 15 14 1/2

11.4 240 1 47.5 47.5 -- 60 6 1/2

240 3 27.5 27.5 27.5 40 8 1/2

480 3 13.7 13.7 13.7 20 12 1/2

12 208 1 58 58 -- 90 3 1

208 3 33 33 33 50 8 1/2

240 1 50 50 -- 70 4 3/4

240 3 29 29 29 40 8 1/2

380 3 19.1 19.1 19.1 30 10 1/2

480 3 14.5 14.5 14.5 20 12 1/2

600 3 11.6 11.6 11.6 15 14 1/2

Form No. EBOOSTERM-0321

English

SPECIFICATIONS

Wire size is based on THHN insulated, copper wire for branch circuit protection at 0.91 derate factor. Circuit breakers and fused

disconnects are to be mounted remote and wired by contractor. Sizes are based on the 2002 NEC table 310-16. Conduit size

based on conductors plus ground wire sizing per Table C1 from Appendix C.

Only 6, 7, and 9 kW models can be field converted to single or three phase (open delta on 3 phase). Check wiring diagram supplied

with the unit when converting the phase of the unit. Larger branch circuit required than for balanced 3 phase of equal kW. Balanced

3 phase available, consult factory.

Circuit Breaker and Fused Disconnect Switch Sizes — 13.5 to 30 kW

kW Volts Phase

Amp Draw Breaker or

Fuse

Size

Copper Wire

Size Conduit SizeL1 L2 L3

13.5 208 1 65 65 -- 90 3 1

208 1 38 38 38 50 8 1/2

240 1 56.3 56.3 -- 90 3 1

240 1 33 33 33 50 8 1/2

480 1 16.3 16.3 16.3 30 10 1/2

600 1 13 13 13 20 12 1/2

15 208 1 72 72 -- 90 3 1

208 3 41.7 41.7 41.7 60 6 3/4

240 1 62.5 62.5 -- 90 3 1

240 3 36.1 36.1 36.1 50 8 1/2

380 3 23.0 23.0 23.0 30 10 1/2

480 3 18.1 18.1 18.1 30 10 1/2

600 3 14.5 14.5 14.5 20 12 1/2

17.25 208 3 47.9 47.9 47.9 60 6 3/4

18 208 1 86.5 86.5 -- 125 1 1-1/4

208 3 50 50 50 70 4 1

240 1 75 75 -- 100 3 1

240 3 43.4 43.4 43.4 60 6 3/4

380 3 27.3 27.3 27.3 40 8 1/2

480 3 21.7 21.7 21.7 30 10 1/2

600 3 17 17 17 30 10 1/2

24 208 1 115.4 115.4 -- 150 1/0 1-1/4

208 3 66.7 66.7 66.7 90 3 1

240 1 100 100 -- 125 1 1-1/4

240 3 57.8 57.8 57.8 90 3 1-1/4

380 3 38.0 38.0 38.0 50 8 1/2

480 3 29.9 29.9 29.9 40 8 1/2

600 3 23 23 23 30 10 1/2

27 208 1 129.8 129.8 -- 175 2/0 1-1/4

208 3 75 75 75 100 3 1

240 1 112.5 112.5 -- 150 1/0 1-1/4

240 3 65 65 65 90 3 1

380 3 38.1 38.1 38.1 50 8 1/2

480 3 32.5 32.5 32.5 50 8 1/2

600 3 26 26 26 40 8 1/2

30 208 1 144 144 -- 200 3/0 1-1/2

208 3 83.3 83.3 83.3 125 1 1-1/4

240 1 125 125 -- 175 2/0 1-1/2

240 3 72.3 72.3 72.3 100 3 1

380 3 45.7 45.7 45.7 60 6 3/4

480 3 36 36 36 50 8 1/2

600 3 28.9 28.9 28.9 40 8 1/2

Form No. EBOOSTERM-0321 9

English

Circuit Breaker and Fused Disconnect Switch Sizes — 36 to 57 kW

The shaded area contains electrical information for International models only.

Wire size is based on THHN insulated, copper wire for branch circuit protection at 0.91 derate factor. Circuit breakers and fused

disconnects are to be mounted remote and wired by contractor. Sizes are based on the 2002 NEC table 310-16. Conduit size

based on conductors plus ground wire sizing per Table C1 from Appendix C.

NOTE: 250 kcmil maximum wire size for terminal block.

WARNING

ELECTRIC SHOCK HAZARD: Consult a licensed electrical

contractor for proper electrical installation conforming to

local electrical codes and the National Electrical Code

(N.E.C.).

SPECIFICATIONS

kW Volts Phase

Amp Draw Breaker or

Fuse

Size

Copper Wire

Size Conduit SizeL1 L2 L3

36 208 1 173 173 -- 225 4/0 1-1/2

208 3 100 100 100 125 1 1-1/4

240 1 150 150 -- 200 3/0 1-1/2

240 3 86.7 86.7 86.7 125 1 1-1/4

380 3 54.7 54.7 54.7 70 4 1

480 3 43.3 43.3 43.3 60 6 3/4

600 3 34.7 34.7 34.7 50 8 1/2

39 208 1 187.5 187.5 -- 250 250 kcmil 2

208 3 108 108 108 150 1/0 1-1/4

240 1 163.5 163.5 -- 225 4/0 2

240 3 94 94 94 125 1 1-1/4

380 3 59.3 59.3 59.3 90 3 1

480 3 47 47 47 60 6 3/4

600 3 37.6 37.6 37.6 50 8 1/2

40 208 3 61.6 61.6 61.6 90 3 1

40.5 208 3 112.5 112.5 112.5 150 1/0 1-1/4

240 3 97.5 97.5 97.5 125 1 1-1/4

480 3 48.8 48.8 48.8 70 4 1

600 3 39 39 39 50 8 3/4

45 208 3 125 125 125 175 2/0 1-1/2

240 1 188 188 -- 250 250 kcmil 2

240 3 108 108 108 150 1/0 1-1/4

380 3 68.6 68.6 68.6 90 3 1

480 3 54 54 54 70 4 1

600 3 43.4 43.4 43.4 60 6 3/4

54 208 3 150 150 150 200 3/0 2

240 3 130 130 130 175 2/0 1-1/2

380 3 82 82 82 125 1 1-1/4

480 3 65 65 65 90 3 1

600 3 52 52 52 70 4 1

57 208 3 158.4 158.4 158.4 200 3/0 2

240 3 137.3 137.3 137.3 175 2/0 1-1/2

380 3 86.7 86.7 86.7 125 1 1-1/4

480 3 68.6 68.6 68.6 90 3 1

600 3 54.9 54.9 54.9 70 4 1

Form No. EBOOSTERM-0321

English

SPECIFICATIONS

Dimensions — Imperial “S” Series

Dimensions — Compact “C” Series 4 to 18 kW

[

9-3/4"

(247 mm)

22-1/16"

(560 mm)

31"

(788 mm)

4" (102 mm)

21-1/2"

(545 mm) 14-1/4"

(362 mm)

9-3/4"

(247 mm)

(53 mm)

4-7/8"

(122 mm)

3/4" Inlet Tee

2-1/8"

(55 mm)

23-1/2"

(598 mm)

Knockout*

Side View

Front View Top View

Inlet*

Outlet*

23-1/2"

(598 mm)

9-3/4"

(247 mm)

3-5/8"

(92 mm)

2-5/8"

(66 mm)

* Outlet, Inlet, and Knockout are

located on the bottom of unit.

Front Side

Electrical Knockouts

bottom—1-1/2" and 2"

13-1/16"

(332 mm)

20-11/16"

(525 mm)

Knockout*

3-1/8"

(79 mm)

2-3/4" (69 mm)

19-13/16"

(502 mm)

10-3/8"

(262 mm) 12-3/4"

(322 mm)

2-3/4"

(69 mm)

Inlet

Outlet

7-7/8"

(200 mm)

6-1/2"

(166 mm)

2-1/2"

(70 mm)

T/P Relief

Valve

Electrical Knockouts left side

and bottom—3/4", 1", and 1-1/4"

5-5/16"

(134 mm)

Top View

Side View

Rear View

* Knockout is located

on the bottom of unit.

Form No. EBOOSTERM-0321 11

English SPECIFICATIONS

Dimensions — Mini-Compact “MC” Series

Side View Top ViewFront View

11-3/4"

(298 mm)

1-1/4"

(31 mm)

1-3/8"

(34 mm)

Knockout*

Inlet

Outlet

T/P

Relief

Valve

18-1/2"

(469 mm)

9-1/8"

(232 mm) 8-1/8"

(206 mm)

12-7/8"

(327 mm)

5-1/2"

(139 mm)

4-3/8"

(138 mm)

3-1/8"

(79 mm)

T/P

Relief

Valve

Electrical Knockouts—

1/2", 3/4", and 1"

Front Side

* Knockout is located

on the bottom of unit.

Dimensions — Compact “C” Series 24 to 57 kW

Side View Top View

Rear View

Knockout*

Inlet

Outlet

T/P Relief

Valve

18"

(457 mm)

3-3/8"

(85 mm)

3" (75 mm)

18-1/16"

(458 mm)

(152 mm)

7-7/8"

(200 mm)

2-1/16"

(54 mm)

15-3/16"

(387 mm)

24"

(610 mm)

16-1/8"

(410 mm) 2-3/4"

(69 mm)

Electrical Knockouts left side

and bottom—1-1/2" and 2"

5-5/16"

(134 mm)

* Knockout is located

on the bottom of unit.

Shipping Weights —

S Models Shipping Weights —

C Models Shipping Weights—

MC Models

Model Shipping Weight

S-6, S-7, S-9,

S-12, S-13,

S-15, S-17, S-18

200 lbs. (91 kg)

S-24, S-27,

S-30, S-36, S-39 214 lbs. (97 kg)

S-40, S-45,

S-54, S-57 224 lbs. (102 kg)

Model Shipping Weight

C-4, C-5 105 lbs. (48 kg)

C-6, C-7, C-9 118 lbs. (54 kg)

C-13, C-15,

C-17, C-18 120 lbs. (54 kg)

C-24, C-27,

C-30, C-36,

C-39, C-45,

C-54, C-57

142 lbs. (64 kg)

Model Shipping Weight

MC-10, MC-10.5,

MC-11, MC-15,

C-17

48 lbs. (22 kg)

Form No. EBOOSTERM-0321

English

INSTALLATION

General

Booster Heaters are shipped with most components pre-

assembled. Care should be taken when unpacking shipping

carton to avoid damage to unit and components enclosed.

Components are shipped with the heater unit.

WARNING

ELECTRIC SHOCK HAZARD:

• Unit must be installed by qualified, trained installers.

Installation must conform to all local electrical and

plumbing codes. Installation by unqualified personnel

will void the unit warranty and may lead to electric

shock or burn, as well as damage to unit and/or its

surroundings. Check with local plumbing and electrical

inspectors for proper procedures and codes.

• Unit is not weatherproof. Locate unit indoors where

ambient air temperature is a minimum of 70°F (21°C).

• Do not place aftermarket covers on or over booster

heater. Doing so can cause temperature and moisture

build-up resulting in premature failure and electrical

shock.

EXPLOSION HAZARD: Do not store or use gasoline or

other flammable vapors or liquids in the vicinity of this or

any other appliance.

Install booster water heater as close as possible to

a commercial dish machine. Employ re-circulation if

distance between water heater and dish machine exceeds

National Sanitation Foundation (NSF) specifications of five

(5) linear feet (1524 mm).

Install booster water heater in a horizontal position with

the base parallel to the floor and the inlet connection at the

lowest point. Improper installation could create an unsafe

condition.

1. Remove the unit from the box.

NOTE: To prevent delay in obtaining warranty coverage,

complete online warranty registration. See the

IMPORTANT OWNER INFORMATION section for

details.

2. Remove tape and protective packaging from all surfaces

of unit.

3. If unit is equipped with legs,

carefully lay unit on its side

and install the four legs.

NOTICE

Do not lay unit on the side with the control panel or inlet

and outlet pipes. Damage to the unit could occur.

NOTE: If unit is not level, use an adjustable wrench to adjust

the foot of each leg until unit is level. Each leg is

adjustable from 6″ (152 mm) to 7″ (178 mm).

4. Place the unit in the appropriate location.

• The location must have a solid foundation along with

being clean and dry.

• Adequate front clearance is required to allow for

accessibility to the control compartment. Hatco



• Location must have adequate clearance to allow for

inspection, testing or replacement of pressure and/or

temperature relief valve.

• Install the booster heater as close as possible to the

commercial dish machine for efficient operation.

WARNING

Make sure the dishtable is strong enough to support the

weight of the booster heater and water when installing with

slide mounting brackets.

Follow standard welding safety and operational procedures

when attaching sliderails to bottom of dishtable.

5. Install unit under dishtable using mounting slide brackets,

if applicable (Compact Series only).

a. Weld slide rails to bottom of dishtable.

         

(3 mm) holes into the sides of the heater jacket.

c. Attach slide brackets to sides of heater with supplied

screws.

d. Slide heater onto slide rails under dishtable.

Weld slide rail

to bottom of

dish table

Fasten slide

brackets to booster

heater sides

Hanging Support

Compact Series Heater Mounted to Dishtable

Form No. EBOOSTERM-0321 13

English INSTALLATION

Plumbing Installation

WARNING

Do not connect booster water heaters to domestic

(consumer) dish machines or other domestic utilized

equipment. This booster may damage domestic equipment.

Use only copper plumbing material. Non-copper plumbing

material may create an unsafe condition.

Refer to the BOOSTER HEATER SIZING CHART in this

manual to ensure proper sizing and avoid personal injury

and/or damage to the booster heater.

CAUTION

Do not connect booster heater directly to a boiler or

furnace coil or any other uncontrolled temperature source.

The booster heater thermostat could be damaged causing

unit to overheat.

NOTICE

Use dielectric couplings when connecting dissimilar

metals, such as galvanized to copper. This will prevent

electrolysis or premature plumbing damage.

Do not turn or adjust inlet or outlet water connection on

Compact Series Booster Heaters or internal water flow will

change and the unit will not produce a consistent outlet

temperature.

Do not back out or loosen any pipe fittings. Doing so may

cause leaks.

Do not lay unit on the side with the control panel or inlet

and outlet pipes. Damage to the unit could occur.

Incoming water in excess of 3 grains of hardness per

gallon (GPG) (0.75 grains of hardness per liter [GPL]) must

be treated and softened before being supplied to booster

heater(s). Water containing over 3 GPG (0.75 GPL) will

decrease efficiency, increase energy use, and reduce the

operating life of the unit through increased lime build-up.

Product failure caused by liming or sediment buildup is

not covered under warranty.

Do not use deionized water. Deionized water will shorten

the life of water reservoir and heating element.

NOTE: Product failure caused by liming or sediment buildup is

not covered under warranty.

NOTE: A 3/4 union and a drain valve are required for easy

servicing.

NOTE: An optional flow restrictor (P/N 03.02.074.00) is

available for installation on the water inlet line.

NOTE: Some dish machines require two booster heaters to be

plumbed in series (not parallel) to meet the demand.

To ensure proper operation, a 29°F (16°C) temperature

differential must be maintained between the inlet and

outlet of each booster heater.

Inlet

Use the following procedure to install the inlet assembly. Refer

to the appropriate “Plumbing Connections” diagram in this

section for more information.

1. Connect the booster water inlet to a copper hot water

supply line from a normal water heater.

• Water temperature from the water heater should be

115°–145°F (46°–63°C) and should not exceed 155°F

(68°C). Minimum temperature differential between inlet

and outlet should never be less than 29°F (16°C).

NOTE: Refer to BOOSTER HEATER SIZING CHART for

application information.

NOTE: The red mark on the inlet and outlet water pipes of

Compact series units must remain in the top most

position.

2. Install a shut-off valve (a full opening gate or ball type).

3. Install one of the temperature/pressure gauges.

• When installing the temperature/pressure gauge, the

temperature sensing element must be in the water

stream and the gauge must be mounted upright (see

illustration below).

NOTE: Tighten gauge during installation by turning the 1/2

brass nut only. DO NOT turn the face of the gauge.

Turning the face will cause inaccurate measurements.

CAUTION

Hatco requires that two temperature/pressure gauges

(Hatco P/N 03.01.003.00) be installed to ensure proper

operation. Install one in the supply line before the pressure

reducing valve and one in the outlet line as close to the

booster heater as possible. This provides a visual check

of the water temperature and pressure before and after the

water heater.

Temperature

sensing element

1/2″ copper

female fitting

adapter

Temperature/

pressure gauge

with 1/2″

pipe thread

3/4″ nominal

copper pipe

Center bottom

of sensor

in copper pipe

3/4″ x 1/2″ x 3/4″

copper tee

Temperature/Pressure Gauge

NOTE: If a check valve or back flow prevention is installed and

cannot be removed, install a back pressure relief valve

(P/N 03.02.039.00) preset at 125 psi (862 kPa) on the

incoming line between the pressure reducing valve and

the inlet to the booster heater. Any discharge must be

directed to an open site drain.

NOTE: If the back pressure relief valve is not acceptable, a high

temperature thermal expansion tank may be substituted.

The thermal expansion tank must be installed on the

inlet side of the booster. The appropriate size and rating

of the thermal expansion tank must be determined by

qualified personnel, assuming a minimum 212°F (100°C)

thermal, and 150 psi (1034 kPa) rating to match the built

in safety devices on the booster.

Form No. EBOOSTERM-0321

English

4. Install the pressure reducing valve if water pressure

available to the booster heater inlet is over 25 psi (172 kPa).

• Set pressure reducing valve at 20 psi (138 kPa) flow

pressure.

NOTE: Be sure water flows through the pressure reducing

valve in the proper direction. Check directional arrow.

Valve will reduce pressure only during flow conditions.

CAUTION

If water supply pressure to the booster inlet is over 138 kPa

(20 psi) during flow, install standard pressure reducing

valve with built-in bypass (Hatco P/N 03.02.004.00) for

proper operation of dish machine rinse nozzles.

NOTE: The pressure reducing valve must be the type equipped

with a high pressure bypass, as supplied by Hatco.

NOTE: Optional brass pressure reducing valve with built-in

bypass (Hatco P/N 03.02.015.00) also available.

Pressure Reducing Valve

5. Install the temperature/pressure relief valve directly into

the marked fitting on the rear or side of the unit.

• Mini-Compact Series: P/N 03.02.020.00

• Compact and Imperial Series: P/N 03.02.022.00

Temperature/Pressure Relief Valve

WARNING

Temperature/pressure protective equipment should not be

less than a combination temperature/pressure relief valve

certified by a nationally recognized testing laboratory that

maintains periodic inspection of the production of this

equipment and meets the requirements for Relief Valves

and Automatic Shutoff Devices for Hot Water Supply

Systems, ANSI Z21.22-1979. The temperature/pressure

relief valve must be marked with a minimum set pressure

not to exceed the marked hydrostatic test pressure of the

booster heater as noted on the unit specifications.

FOR INSTALLING PRESSURE AND TEMPERATURE

RELIEF VALVES IN ACCORDANCE WITH AMERICAN

NATIONAL STD. Z21.22-1979. Combination pressure and

temperature relief valves with extension thermostats must

be installed so that the temperature-sensing element is

immersed in the water within the top 6″ (152 mm) of the

tank. They must be installed directly in a tank tapping.

Combination pressure and temperature relief valves that

do not have extension elements must be mounted directly

in a tank tapping located within the top 6″ (152 mm) of the

tank, and shall be adequately insulated and located so as

to assure isolation from ambient conditions that are not

indicative of stored water temperature. TO AVOID WATER

DAMAGE OR SCALDING DUE TO VALVE OPERATION,

DRAIN PIPE MUST BE CONNECTED TO VALVE OUTLET

AND RUN TO A SAFE PLACE OF DISPOSAL. Discharge

line must be as short as possible and be the same size

as the valve discharge connection throughout its entire

length. Drain line must pitch downward from the valve and

must terminate between 1-1/2″ (38 mm) and 6″ (152 mm)

above the floor drain where any discharge will be clearly

visible. The drain line shall terminate plain, not threaded,

with material serviceable for temperatures up to 250°F

(121°C) or greater. Excessive length, over 30′ (9.1 m), or

use of more than four elbows can cause a restriction and

reduce the discharge capacity of the valve. No shut-off

valve shall be installed between the relief valve and tank, or

in the drain line. Valve lever must be tripped periodically to

assure that waterways are clear. This device is designated

for emergency safety relief and shall not be used as an

operating control. The valves are set to relieve at 150 psi

(1034 kPa) or when water temperature reaches 210°F

(99°C). Read tag on valve for additional information.

CAUTION

BURN HAZARD: Valves supplied by Hatco are designed for

high temperature commercial operation. Do not substitute

Hatco valves with valves designed for domestic water

heaters.

Do not use an anti-siphon or check valves on incoming

water line.

INSTALLATION

Form No. EBOOSTERM-0321 15

English INSTALLATION

Temperature/

Pressure Gauge

Temperature/

Pressure Gauge

Shock Absorber

for water hammer.†

Discharge from T/P Valve.

Air gap must comply

with plumbing code.

3/4″ Gate or

Ball Valve‡

Blended Phosphate Water

Treatment System†

Outlet

Drain Valve‡

3/4″

Union‡

Back

Pressure

Relief Valve†

Inlet

Floor Drain‡

Outlet

Inlet

NOTE: Centerline of booster “T” fitting must

not extend closer than 102 mm (4″) to the floor.

Pressure Reducing Valve

with High Pressure By-pass

(20 psi [138 kPa] flow

pressure maximum) Temperature/Pressure

Relief Valve, 150 PSI/210°F

(1034 kPa/99°C)

Copper Water Inlet

from primary

water heater.

Copper Outlet

to Dishwasher.

Temperature/

Pressure Gauge

Temperature/

Pressure Gauge

Floor

Drain‡

Shock Absorber

for water hammer.†

Copper Outlet

to Dishwasher.

Discharge from T/P Valve.

Air gap must comply

with plumbing code.

3/4″ Gate or

Ball Valve‡

Copper Water Inlet

from primary

water heater.

Blended Phosphate Water

Treatment System†

Outlet

3/4″

Union‡

Back

Pressure

Relief Valve†

Inlet

Drain

Valve‡

Pressure Reducing Valve

with High Pressure By-pass

(20 psi [138 kPa] flow

pressure maximum) Temperature/Pressure

Relief Valve, 150 PSI/210°F

(1034 kPa/99°C)

NOTE: Centerline of booster “T” fitting must

not extend closer than 102 mm (4″) to the floor.

Two Imperial Models Connected in Series

Imperial “S” Series

† Not supplied, but is available as an option/accessory.

‡ Not supplied with booster heater.

Plumbing Connections

WARNING

Valves, gauges, and unions must be installed per diagram

to ensure proper operation, servicing, and warranty

coverage.

Form No. EBOOSTERM-0321

English

INSTALLATION

Temperature/

Pressure Gauge

Pressure Reducing Valve

with High Pressure By-pass

(20 psi [138 kPa] flow

pressure maximum)

Temperature/

Pressure Gauge

Shock Absorber

for water hammer.†

Discharge from T/P Valve.

Air gap must comply

with plumbing code.

3/4″ Gate or

Ball Valve‡

Blended Phosphate Water

Treatment System†

Back

Pressure

Relief Valve†

Inlet

Temperature/Pressure

Relief Valve, 150 PSI/210°F

(1034 kPa/99°C)

Flow

Restrictor†Floor Drain‡

Drain Valve‡

NOTE: Centerline of booster “T” fitting must

not extend closer than 102 mm (4″) to the floor.

Copper Water Inlet

from primary

water heater.

Copper Outlet

to Dishwasher.

Temperature/

Pressure Gauge

Temperature/

Pressure Gauge

Floor Drain‡

Shock Absorber

for water hammer.†

Discharge from T/P Valve.

Air gap must comply

with plumbing code.

3/4″ Gate or

Ball Valve‡

Blended Phosphate Water

Treatment System†

Outlet

Back

Pressure

Relief Valve†

Inlet

Drain Valve‡

Pressure Reducing Valve

with High Pressure By-pass

(20 psi [138 kPa] flow

pressure maximum)

Temperature/Pressure

Relief Valve, 150 PSI/210°F

(1034 kPa/99°C)

Copper Water Inlet

from primary

water heater.

Copper Outlet

to Dishwasher.

Mini-Compact Models

Compact Series

Plumbing Connections

WARNING

Valves, gauges, and unions must be installed per diagram

to ensure proper operation, servicing, and warranty

coverage.

† Not supplied, but is available as an option/accessory.

‡ Not supplied with booster heater.

Form No. EBOOSTERM-0321 17

English INSTALLATION

Temperature

sensing element

Temperature/

pressure gauge

with 1/2″

pipe thread

1/2″ copper

female fitting

adapter

3/4″ nominal

copper pipe

Recommended Temperature/Pressure Gauge Installation

Temperature

sensing element

1/2″ copper

female fitting

adapter

Temperature/

pressure gauge

with 1/2″

pipe thread

3/4″ nominal

copper pipe

Center bottom

of sensor

in copper pipe

3/4″ x 1/2″ x 3/4″

copper tee

Alternate Temperature/Pressure Gauge Installation

WARNING

Hatco has always endorsed the use of safety equipment

when using a booster water heater or storage-type

water heater. Hatco booster heaters are shipped with a

temperature/pressure relief valve at no extra charge. This

valve must be installed into the marked opening provided

in the tank. Valves supplied by Hatco are designed for

high temperature commercial operation. Do not substitute

Hatco supplied valves with valves designed for domestic

operation.

It is essential to recognize that even though a water heater

may be properly installed initially and approved, there

always exists the possibility that unknowing individuals

might alter or change the installation in a manner that

would render it unsafe. Therefore, it is important that all

safety programs provide some mechanism to assure that

these installations are inspected periodically.

Outlet

1. Flush the water supply line to remove any pipe compound

and foreign matter.

2. Connect the booster heater water outlet to the commercial



union and copper piping.

WARNING

DO NOT turn or adjust water outlet connection on Large

Compact Series units (C-24 to C-57).

NOTE: Red marks on water inlet and outlet pipe for C-24 to

C-57 series units must remain in the top most position.

NOTE: Be certain the connection is made to the final rinse and

not to the wash tank.

3. Install a temperature/pressure gauge in the outlet line. The

temperature sensing element must be in the water stream

and the gauge must be mounted upright.

• Water temperature at the outlet should be 185°–190°F

(85°–88°C).

NOTE: Some dish machines require two booster heaters to be

plumbed in series (not parallel) to meet the demand.

To ensure proper operation, a 29°F (16°C) temperature

differential must be maintained between the inlet and

outlet of each booster heater.

NOTE: Hatco recommends installing an optional shock

absorber (P/N 03.04.057.00) in the outlet line as close

as possible to the commercial dish machine solenoid

rinse valve. The shock absorber softens the water

hammer caused by automatic dish machine valves.

Plumbing Installation Inspection

1. Close the drain valve and fill the booster heater with water.

2. Check all pipe connections for leaks.

3. Make sure the temperature/pressure relief valve discharge

is not blocked.

4. Vent air from the tank before operating by opening the

temperature/pressure relief valve or venting through the

dish machine rinse nozzles.

WARNING

DO NOT turn on power to the booster heater until tank has

been filled with water and all air has been vented through

the dish machine rinse nozzle. The heating elements

will burn out in seconds if operated when they are not

immersed in water.

Form No. EBOOSTERM-0321

English

INSTALLATION

Electrical

Knockout

Electrical

Knockouts

Electrical

Knockout

Compact Series

Imperial Series Mini-Compact Series

Electrical — All Sizes and Voltages

General

Hatco Electric Booster Water Heaters are available for

operation on standard power systems. Check the specification

label for the proper power supply.

All internal electrical connections have been made at the

factory. See the “Circuit Breaker and Fused Disconnect Switch”

chart in the SPECIFICATIONS section for supply wire size,

fuse, breaker, and conduit recommendations. Consult local

codes for verification and compliance.

WARNING

ELECTRIC SHOCK HAZARD:

• Unit must be installed by qualified, trained installers.

Installation must conform to all local electrical and

plumbing codes. Installation by unqualified personnel

will void the unit warranty and may lead to electric

shock or burn, as well as damage to unit and/or its

surroundings. Check with local plumbing and electrical

inspectors for proper procedures and codes.

• Turn OFF power at fused disconnect switch/circuit

breaker and allow unit to cool before performing any

cleaning, adjustments, or maintenance.

• Consult a licensed electrical contractor for proper

electrical installation conforming to local electrical

codes and the National Electrical Code (N.E.C.).

NOTICE

Units are voltage-specific. Refer to specification label

for electrical requirements before beginning installation.

Connecting unit to incorrect power supply will void

product warranty and may damage unit.

Electrical Connections

1. Remove the front jacket cover screws, pull the cover

forward and remove the cover.

NOTE: On Imperial models, there is a hinged access panel

under the front jacket cover. Remove the bottom screw

and lift the panel up to expose the fuse blocks.

• On Mini-Compact models, remove front cover screws.

Ease cover forward and upward.

• On Compact models, the control box is under the front

hinged jacket cover.

2. Locate the terminal or fuse block(s) inside the unit.

NOTE: See “Circuit Breaker and Fused Disconnect Switch”

chart in the SPECIFICATIONS section for proper

connections and wire size.

NOTE: Only 6, 7, and 9 kW models, in 208 or 240 volt, can be

converted to single or three phase in the field. Refer to

the wiring diagram for proper wiring connections at the

terminal block.

3. Bring power leads from a properly sized disconnect

switch or circuit breaker through the knockout provided on

the unit. Connect leads to the terminal or fuse block(s).

USE COPPER WIRE ONLY. TIGHTEN CONNECTIONS

PROPERLY TO A MINIMUM OF 40 INCH POUNDS.

NOTE: Due to the rigors of transportation all connections

should be checked for tightness before heater is put

into operation.

4. Properly connect an equipment grounding connector to the

grounding lug (located near the supply terminals).

CAUTION

DO NOT turn on power to the booster heater until tank has

been filled with water and all air has been vented through

the dish machine rinse nozzles. Heating elements will burn

out in seconds if operated when not immersed in water.

5. Replace and secure cover(s).

Electrical Knockout Locations

Form No. EBOOSTERM-0321 19

English OPERATION

General

Use the following procedures to operate Hatco Electric Booster

Water Heaters.

CAUTION

BURN HAZARD: Water in unit is very hot. Wear protective

gloves and proper attire when operating to avoid injury.

Controls

The following is a list of the available controls for electric

booster water heaters.

Power I/O (on/off) Switch—Turns power on and off to the

heating elements.

Reset Icon—Indicates the Power I/O switch also is the reset

switch. The high limit switch trips when the unit exceeds the

high temperature limit. Use the Power I/O (on/off) switch to

reset the unit when the Error Indicator Light is illuminated.

Power Indicator Light—Illuminates when power is on, shuts

off when power is off.

Error Indicator Light—Illuminates/flashes when the unit is

malfunctioning.

• Flashing Light = Probe is defective or low water error

• Solid Light = High Limit tripped

Startup

1. Close the drain valve.

2. Open the shutoff valve to the primary water supply line.

The water temperature at inlet should be 115° to 145°F

(46° to 63°C) and should not exceed 155°F (68°C).

NOTE: Minimum temperature differential between inlet and

outlet should never be less than 29°F (16°C).

3. Vent all the air from the tank through the dish machine

rinse nozzles and the temperature/pressure relief valve

when the tank is filled with water.

CAUTION

DO NOT turn on power to the booster heater until tank has

been filled with water and all air has been vented through

the dish machine rinse nozzles. Heating elements will burn

out in seconds if operated when not immersed in water.

4. Check all plumbing connections for leaks.

5. Check the temperature/pressure relief valve discharge

opening to be sure it is not blocked and no scale or other

foreign matter has reduced the size of the opening.

6. Turn on the booster water heater.

• For models with a Power I/O (on/off) switch, move the

Power I/O (on/off) switch on the control panel to the I

(on) position.

• For models without a Power I/O (on/off) switch, turn on

power at the fused disconnect switch/circuit breaker.

NOTE: The power indicator light will illuminate when the

unit turns on. Some units are equipped with an error

indicator light that will illuminate when the unit needs to

be serviced.

NOTE: All models can be configured with or without a Power

I/O (on/off) switch.

7. When the booster water heater has had sufficient

heating time, operate the rinse cycle and check the water

temperature and pressure readings on the gauges.

• Water temperature at the booster outlet should be

185°–190°F (85°–88°C) and flow pressure should be

20 psi (138 kPa) maximum.

NOTE: Outlet water temperatures can be adjusted for

Low-Temperature Dish Machine applications. See the

MAINTENANCE section for thermostat adjustment

procedure.

WARNING

Units are equipped with a high temperature limit safety

switch that will shut off the power if the unit overheats.

Contact an Authorized Hatco Service Agent if the high

temperature limit safety switch cannot be reset or

continues to trip.

Power Indicator Light

Error Indicator Light

Power I/O

(on/off) Switch

Reset Icon

Control Panel (Imperial and Compact models shown)

Shutdown

Under normal and regular operation, Hatco recommends that

the unit be turned on at all times.

If the booster heater will not be used for an extended period

of time or will be exposed to freezing conditions, it should be

drained to prevent damage to the unit.

1. Move the Power I/O (on/off) switch to the O (off) position,

and turn off power at the fused disconnect switch/circuit

breaker.

2. Close the shutoff valve to the primary water supply line.

3. Open the drain valve and drain the water from the booster

heater tank.

NOTICE

Always drain booster heater with power to the unit off or

element burnout could occur.

Form No. EBOOSTERM-0321

English

MAINTENANCE

High Temperature Limit Safety Switch

All Hatco Electric Booster Water Heaters are equipped with

a manually reset high temperature limit safety switch. If the

temperature of the water in the heater exceeds 210°F (99°C)

the safety switch will shut off the power. The switch must be

manually reset.

If the high temperature limit safety switch needs to be reset use

the following procedure:

Electronic Controls

The error indicator light will illuminate if the unit needs to be reset.

1. Move the Power I/O (on/off) switch to the O (off) position,

and/or turn off power at the fused disconnect switch/circuit

breaker.

2. Allow unit to cool.

3. Move the Power I/O (on/off) switch to the I (on) position,

and/or turn on power at the fused disconnect switch/circuit

breaker.

4. If tripping repeats, call an Authorized Service Agent.

DO NOT attempt to adjust the High Temperature Limit

Safety Switch.

Mechanical Controls

1. Move the Power I/O (on/off) switch to the O (off) position,

and/or turn off power at the fused disconnect switch/circuit

breaker.

2. Remove the access cover.

3. Push the red reset button.

4. If tripping repeats, call an Authorized Service Agent.

DO NOT attempt to adjust the High Temperature Limit

Safety Switch.

Front View of

Thermostat

Adjustment Screws

Access Cover

Inner

Screw

Outer

Screw

High Limit Switch

Reset Button

Thermostat

Adjustment

Screw

Thermostat

Adjustment

Screw

Mechanical Control Thermostat Adjustment and High Temperature

Limit Safety Switch (Imperial “S” Model Shown)

General

Electric Booster Water Heaters are designed for maximum

durability and performance with minimum maintenance.

WARNING

ELECTRIC SHOCK HAZARD:

• Turn OFF power at fused disconnect switch/circuit

breaker and allow unit to cool before performing any

cleaning, adjustments, or maintenance.

• This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric

shock or burn.

• Use only Genuine Hatco Replacement Parts when

service is required. Failure to use Genuine Hatco

Replacement Parts will void all warranties and may

subject operators of the equipment to hazardous

electrical voltage, resulting in electrical shock or burn.

Genuine Hatco Replacement Parts are specified to

operate safely in the environments in which they are

used. Some aftermarket or generic replacement parts

do not have the characteristics that will allow them to

operate safely in Hatco equipment.

This unit has no “user-serviceable” parts. If service

is required on this unit, contact an Authorized Hatco

Service Agent or contact the Hatco Service Department at

800-558-0607 or 414-671-6350.

Thermostat Adjustment

The thermostat is factory calibrated at 185°–190°F (85°–88°C).

If adjustment or recalibration is required due to the rigors of

transportation, use the appropriate procedure based on the

control on the unit.

NOTE: Low temperature dish machines require the thermostat(s)

to be adjusted to 140°–150°F (60°–66°C).

Electronic Controls

Contact an Authorized Hatco Service Agent or contact the

Hatco Service Department at 800-558-0607 or 414-671-6350.

Mechanical Controls

1. Move the Power I/O (on/off) switch to the O (off) position,

and/or turn off power at the fused disconnect switch/circuit

breaker.

2. Remove the access cover.

3. Adjust the temperature setpoint to the desired temperature.

• To lower the temperature setpoint, turn the outer screw

counterclockwise.

• To raise the temperature setpoint, turn the outer screw

clockwise.

NOTE: 1/6 turn of the outer screw equals 12°F (6.7°C).

NOTE: If recalibration is necessary, with the outer screw at high

stop, turn the inner screw clockwise to raise the set point.

NOTE: 1/6 turn of the inner screw equals 8°F (4.4°C).

La page charge ...

Hatco C-7-208-3 Manuel utilisateur

Marque: Hatco

Modèle: C-7-208-3

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hatco C-7-208-3 User manual

Hatco C-7-208-3 Manuel utilisateur

Hatco C-7-208-3 Manuel utilisateur

dans d''autres langues

Documents connexes