Magtek cDynamo Quick Installation Manual
- Taper
- Quick Installation Manual
cDynamo
Secure Card Reader Authenticator for iPad®
Quick Installation Guide
*Made for
iPad Air
iPad Air 2
iPad (iPad “Flat-out Fun”)
iPad mini 3
iPad mini 2
Drawings
micro-USB port
Front Back
MagneSafe™ secure card reader authenticator (SCRA)
cDynamo SCRA enclosure is made up of
two pieces that easily snap together around
the iPad.
1. Place the iPad device inside the top
enclosure. Be sure the iPad slides to
the top and snaps in place.
2. Slide the bottom enclosure into place
by lining up the Lightning connector
on cDynamo and the Lightning port of
your iPad device.
3. Sections 1 and 3 shown in the diagram
should snap in place to the inside of
the enclosure, and section 2 should
snap to the outside of the enclosure.
When removing the iPad from the top
enclosure, pull both sides out so the case
is pushed past the buttons on your iPad
device.
Top enclosure
Bottom enclosure
1
2
3
Connect the Top and Bottom Enclosures
Lightning™ connector
Additional Contents
micro-USB cable
Part Number (PN) 1000002547
www.magtek.com
*Product Compatibility
cDynamo comes in two different enclosure sizes:
PN 21087005 with VESA mount
Made for
iPad Air
iPad Air 2
iPad (iPad “Flat-out Fun”)
PN 21087006 in mobile hand-held form
Made for
iPad mini 3
iPad mini 2
Power
cDynamo is powered through the iOS device. It only uses power during a
transaction. To charge your iOS device while cDynamo is attached, connect
the optional micro-USB cable (micro-B) to the back of cDynamo, and then
connect the opposite end (USB-A) to the appropriate Apple charging adapter.
Connection - USB Port
Plug the micro-USB connection end of the cable into cDynamo’s micro-
USB port, then attach the USB connection to your Apple charging adapter.
Pass-through micro-USB port allows the iPad device to charge without
disconnecting cDynamo.
Connection - Lightning
Lightning connector supports charge ONLY; iTunes synchronization is not
available.*
Mounting
VESA Mount = MIS-D 4”x 4” (100mm x 100mm), Qty 4 - M4 screw threads.
USB A PLUGRIGHT ANGLE MICRO USB B PLUG
Power, Connection, and Mounting
Compliance
FCC
FCC WARNING STATEMENT: This equipment has been tested and was found to comply with the limits for a Class B digital device
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference with radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
FCC COMPLIANCE STATEMENT: This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Canadian
CANADIAN DOC STATEMENT: This digital apparatus does not exceed the Class B limits for radio noise from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
la classe B prescrites dans le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE
CE STANDARDS: Testing for compliance with CE requirements was performed by an independent laboratory.
The unit under test was found compliant with standards established for Class B devices.
UL/CSA
UL/CSA: This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
RoHS
RoHS STATEMENT: When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction
of Hazardous Substances (RoHS) European Directive 2002/95/EC. The marking is clearly recognizable, either as written words like
“Pb-free”, “lead-free”, or as another clear symbol ( ).
Apple Legal Notice
“Made for iPad” means that an electronic accessory has been designed to connect specifically to iPad and has been certified by
the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory with iPad may affect wireless performance.
Credit lines and trademark symbols
AirPlay, iPad, iPhone, iPod, iPod classic, iPod nano, iPod touch, and Retina are trademarks of Apple Inc., registered in the U.S. and
other countries. iPad Air, iPad mini, and Lightning are trademarks of Apple Inc.
Pb
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200074 rev 40 4/19
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740
p 562-546-6400 | f 562-546-6301 | www.magtek.com
Technical Support
When calling the support team please have your reader charged and have the part
number and serial number(s) available.
651.415.6800
-
1
-
2
-
3
-
4
Magtek cDynamo Quick Installation Manual
- Taper
- Quick Installation Manual
dans d''autres langues
- English: Magtek cDynamo
Documents connexes
-
Magtek iDynamo Manuel utilisateur
-
Magtek DynaPAD Quick Installation Guide
-
Magtek eDynamo Quick Installation Guide
-
-
Magtek DynaFlex Kiosk Family Quick Installation Guide
-
Magtek Dynamag Quick Installation Guide
-
-
-
-