Yamaha MCR-550 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire
OWNER’S MANUAL
MODE D’EMPLOI
CAB
CD RECEIVER
AMPLI-TUNER CD
i En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances
around CRX-550.
Top: 20 cm (8 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from
the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam. When this unit is plugged into the wall
outlet, do not place your eyes close to the opening of the disc tray
and other openings to look into inside.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by . This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
LASER
Type Semiconductor laser GaAs/GaAlAs
Wave length 780 nm
Output Power 10 mW
WARNING
DO NOT TOUCH THIS UNIT WHEN IT IS USED
CONTINUOUSLY AT HIGH VOLUME BECAUSE THE
BOTTOM OF THIS UNIT MAY BECOME HOT. IT MAY LEAD
TO INJURIES SUCH AS BURNS, ETC.
1 En
PREPARATION OPERATION
ADDITIONAL
INFORMATION
English
WHAT YOU CAN DO WITH THIS UNIT.........2
SUPPLIED ACCESSORIES.................................2
PLAYABLE DISCS AND FILE FORMAT.........3
REMOTE CONTROL...........................................4
Installing the batteries in the remote control.............5
Using the remote control ...........................................5
FRONT PANEL DISPLAY...................................6
FRONT PANEL AND BASIC OPERATION .....7
PREPARATIONS...................................................8
Connecting speakers/antennas/external components
...............................................................................8
Connecting the DAB/FM antenna
(U.K. and Australia models)..................................9
Connecting the power cable.......................................9
Other connection........................................................9
LISTENING TO MUSIC.....................................10
Playback operation...................................................10
Operation for iPod...................................................11
Operation for CD/USB............................................11
Switching the display...............................................12
Playback sound........................................................12
LISTENING TO DAB STATIONS
(U.K. and Australia models)............................13
Preparing the DAB tuning.......................................13
Tuning DAB stations...............................................13
Presetting DAB stations...........................................13
Selecting preset DAB stations (Preset tuning)......... 13
DAB station information.........................................14
DAB frequency information....................................14
LISTENING TO FM RADIO STATIONS ........15
Tuning to FM radio stations....................................15
Presetting FM radio stations....................................15
Selecting preset FM radio stations (Preset tuning).. 15
Displaying Radio Data System information
(U.K. model only) ...............................................15
CLOCK AND TIMER .........................................16
Using the clock........................................................16
Using timer and sleep timer.....................................16
USING USEFUL FUNCTIONS..........................17
Using option menu...................................................17
Using DAB option menu
(U.K. and Australia models)................................19
TROUBLESHOOTING .......................................20
General.....................................................................20
DAB reception (U.K. and Australia models)...........21
FM reception............................................................21
iPod..........................................................................22
USB .........................................................................23
Disc playback ..........................................................23
Remote control ........................................................24
HANDLING COMPACT DISCS ........................25
SPECIFICATIONS...............................................25
CONTENTS
PREPARATION
OPERATION
ADDITIONAL INFORMATION
About this manual
This manual describes how to operate this unit using a remote control except when it is not available. Some of these
operations are also available using the front panel buttons.
The symbol “ with page number(s) indicates the corresponding reference page(s).
Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
2 En
PREPARATION
Make sure you have all of the following items.
WHAT YOU CAN DO WITH THIS UNIT
Play back music on the iPod /Discs/ USB device/external device \ p. 10
This unit can play back music stored in your iPod, CDs and music stored in USB device. Also you can
connect external device and enjoy music from the device that you connected.
*Refer to p. 3 for the playable disc and file format
Receive DAB/DAB+ station (U.K. and Australia models) \ p. 13
You can enjoy listening to DAB/DAB+ station. Also you can display station information on the front
panel display.
Receive FM Radio stations and Radio Data System information
(U.K. model only)
\ p. 15
You can enjoy listening to FM radio stations with this unit. Also when the Radio Data System
broadcasting station is received, you can display Radio Data system information on the front panel of
this unit (U.K. model only).
Enhance sound for Audio CDs by bit data expansion \ p. 12
You can listen to Audio CDs with clear sound.
Improved sound for compressed source by Music Enhancer \ p. 12
You can enjoy compressed music source (MP3 and WMA) with better sound quality.
Set the Clock and Timer \ p. 16
You can set the clock and choose to display it on the front panel display during standby mode. Also
you can set the timer to play back music from the selected input source.
Charging iPod and USB device \ p. 9
This unit can charge iPod and USB device during standby mode.
Boost bass sound by connecting a subwoofer \ p. 8
You can enjoy boost bass sound by connecting a subwoofer.
SUPPLIED ACCESSORIES
Remote control
Batteries (x 2)
(AAA, R03, UM-4)
Indoor FM antenna USB cap* Dock cover*
Keep the USB cap out of the reach of
children, so that it is not mistakenly
swallowed.
CAUTION
* The USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using.
When the USB cap and the Dock cover
are covered.
(Canada model)
Indoor DAB/FM
antenna
(U.K. and Australia models)
3 En
PREPARATION
English
Playable discs
Use compact discs bearing the marks below.
To play back an 8-cm (3 in) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3 in) CD.
Playable MP3 and WMA files
MP3
*
1
Variable bitrate is supported.
WMA
Version 8
Version 9 (Standard and variable bitrates are supported.
Professional and Lossless are not supported.)
*
2
Both constant and variable bitrates are supported.
Playback for Data Disc starts in alphanumeric order of files.
Playback for USB starts in order by date and time of creation.
Copyright-protected WMA (DRM) files cannot be played back
by this unit.
The disc must be ISO 9660 compatible.
The maximum file and folder numbers are as follows.
*
3
The root is counted as one of the folders.
PLAYABLE DISCS AND FILE FORMAT
....
Compact discs (digital audio)
....
CD-R,CD-RW digital audio discs
CD-R or CD-RW discs bearing one of
the following phrases.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
Finalized CD-R or CD-RW discs
This compact disc player may not be able to
play some CD-R/CD-RW discs or discs on
which recording was not made correctly.
....
CD-TEXT discs
To prevent a malfunction of this unit:
Do not use any nonstandard shaped
disc (heart, etc.) available on the
market because it might damage the
unit.
Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
Note: Do not use any lens cleaners as they may be a
cause of malfunction.
Note
Format
Bitrate
(kbps)
Sampling
frequency
(kHz)
MPEG 1 Audio Layer-3
32-320
*1
32/44.1/48
MPEG 2 Audio Layer-3, 2
8-160
*1
16/22.05/24
Profile
Bitrate
(kbps)
Sampling
frequency
(kHz)
High Profile
32-320
*2
32/44.1/48
Mid Profile
16-32 22.05
Notes
Data Disc USB
Maximum total number of file
and folder
*3
512 9,999
Maximum folder number
*3
255 255
Maximum file number per
folder
511 255
4 En
REMOTE CONTROL
1 Infrared signal transmitter ( P. 5)
2 : Open and close tray
3 TIMER ( P. 16)
4 iPod Control buttons ( P. 11)
Used to operate your iPod
/ : Scroll buttons
MENU: Returns to the upper level in the iPod menu
ENTER: Select group/start playback
: Skip forward/press and hold to fast forward
: Skip backward/press and hold to fast backward
: Starts or pauses playback
SHUFFLE: Selects the shuffle play mode
REPEAT: Selects the repeat play mode
5 Input select buttons ( P. 10, 13, 15)
Select the input source.
6 DAB/FM control buttons
MEMORY: Starts preset tuning and stores preset station ( P. 13, 15).
PRESET u / d: Selects preset station ( P. 13, 15).
TUNING / : Selects the desired station when you press this button
( P. 13, 15).
7 MONO
Sets FM Broadcasting receiving mode to monaural mode ( P. 15).
8 DIMMER
Changes brightness of the front panel. Choose brightness from normal (bright),
mid dim, or dim by pressing this button repeatedly.
9 DISPLAY ( P. 15)
Switches the information shown on the front panel.
0 Option control buttons ( P. 17)
OPTION: Enters option menu mode.
////ENTER: For selecting and confirming an item.
A CD/USB control buttons ( P. 11)
Controls CD/USB playback
: Stops playback
: Pauses playback
: Starts playback
/ : Rewind/fast-forward music
/ : Skips to the beginning of current track or next track
SHUFFLE: Selects the shuffle play mode
REPEAT: Selects the repeat play mode
FOLDER / : Skips to the first file of selected folder for an MP3 or
WMA recorded on disc/USB device.
B Numeric buttons ( P.
11)
Input numbers.
Press ENTER to confirm the entry.
Press CLEAR to clear the entry.
C CLOCK ( P. 16)
D (on/standby)
E SLEEP ( P. 16)
F Volume control buttons
Controls the volume.
Press MUTE to turn off the sound. Press again to resume the volume.
D
E
F
C
1
2
3
4
5
9
A
B
7
8
0
6
d
d
d
d
REMOTE CONTROL
5 En
PREPARATION
English
Notes on batteries
Change both batteries when the operation range of the remote
control decreases.
Use AAA, R03, UM-4 batteries.
Make sure that the polarities are correct. See the illustration
inside the battery compartment.
Remove the batteries if the remote control is not to be used for
an extended period of time.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of the unit during
operation.
The area between the remote control and the unit must be clear
of large obstacles.
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following types
of conditions:
– high humidity, such as near a bath
high temperature, such as near a heater or a stove
extremely low temperatures
dusty places.
Do not expose the remote control sensor to strong lighting, in
particular, an inverter type fluorescent lamp; otherwise, the
remote control may not work properly. If necessary, position
the system away from direct lighting.
Installing the batteries in the
remote control
1
3
2
Using the remote control
Notes
30˚ 30˚
Within 6 m
(20 feet)
6 En
1 SLEEP indicator
Lights up when the sleep timer is on ( P. 16).
2 PRESET indicator
Lights up when you preset DAB/FM radio stations
( P. 13, 15).
3 STEREO indicator
Lights up when this unit is receiving a strong signal from an
DAB/FM stereo broadcast.
4 AUTO indicator
Lights up when this unit is in the Automatic Tuning mode
( P. 15).
5 SHUFFLE indicator
Lights up when you set your iPod/CD/USB to shuffle play
( P. 11).
6 REPEAT indicator
Lights up when you set your iPod/CD/USB to repeat play
( P. 11, 12).
7 Radio Data System indicators (U.K. model only)
The name of the Radio Data System data offered by the
currently received Radio Data System station lights up
( P. 15).
8 MUTE indicator
Lights up when the sound is muted.
9 Multi information display
Shows the various information such as the tuning frequency.
0 TUNED indicator
Lights up when this unit is tuned into DAB/FM radio station
( P. 13, 15).
A MEMORY indicator
Flashes when searching for FM radio station by automatic
preset tuning. Lights up when you preset FM radio stations
automatically or manually ( P. 15).
Lights up when you preset DAB radio stations manually
( P. 13).
B Multi information indicator
Indicates the music information currently displayed on Multi
information display ( P. 12).
C Operation indicators
Shows operable option control buttons for a currently
selected OPTION item.
D TIMER indicator
Lights up when the timer is on ( P. 16).
FRONT PANEL DISPLAY
GENRES
SONGS
ALBUMS
ARTISTSPLAYLISTS
MEMORY
TUNED
SLEEP
STEREO
AUTO
SHUFFLE
REPEAT
PS
PTY RT CT
MUTE
PRESET
7 En
OPERATION
English
OPERATION
y
This unit has an automatic standby function, which will automatically switch the unit to standby mode if the unit is left turned on for
1 hour without playback or any other operation being performed. This function is not available when the source is set to DAB/FM/
AUX1/AUX2.
FRONT PANEL AND BASIC OPERATION
iPod dock
(on/standby):
Unit on/standby
The indicator lights up as
follows:
Brightly lit: Power is on
Dimly lit: Standby mode
When iPod/USB device is
charged or the clock is displayed
on the front panel during the
standby mode, the indicator
lights up brightly.
Note
:
Disc tray open/close
:
Play/pause playback
:
Stop playback
INPUT:
Selects an input source.
VOLUME
USB port:
P. 9, 10
PHONES:
Connecting headphones
No sound is output from the speakers
when headphones are connected.
Disc tray
/
:
Skip backward and forward/press
and hold to rewind and fast-forward
PRESET < >:
Selects preset station
Front panel
display:
P. 6
Down Up
* U.K. and Australia models only
8 En
Make sure you read the following procedure and note carefully before connecting the system. For information on the
speakers (NS-BP200), refer to the owner’s manual supplied with it.
Connecting the system
1 Connect the speaker terminals (L) of the unit to the speaker terminals of the left speaker and the speaker terminals (R)
of the unit to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set
(NS-BP200).
2 Connect the supplied FM antenna to the FM jack.
(For U.K. and Australia models, the DAB/FM antenna is supplied. Refer to page 9 for details.)
Do not connect this unit or other components to the main power until all connections between components are complete.
Do not let the bare speaker wires touch each other or any metal part of the unit. This could damage the unit and/or the speakers.
All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,
refer to the owner’s manual for each of your components.
When connecting speakers other than NS-BP200, use speakers having more than 6Ω impedance.
If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use
commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.
PREPARATIONS
Connecting speakers/antennas/external components
CAUTION
Notes
DVD player etc.
Subwoofer
Right speaker
(NS-BP200)
Left speaker
(NS-BP200)
CD Receiver (CRX-550)
(Canada model)
Portable
player
RCA stereo
cable
3.5mm stereo
mini plug cable
Be sure to remove insulation from
the end of each speaker cable.
PREPARATIONS
9 En
OPERATION
English
To enjoy radio on this unit, connect the supplied DAB/FM
antenna to the DAB/FM jack.
After you made all connections, connect the power cables
of this unit.
Stationing iPod
Station or remove your iPod whenever you want.
y
Your iPod is automatically charged when your iPod is set in the
iPod dock even if the unit is in standby mode.
This unit is compatible with iPod (5th generation), iPod classic,
iPod nano and iPod touch.
To secure the connection, attach a compatible Dock
Adapter supplied with the iPod or an iPod Universal Dock
Adapter (sold separately), and remove the protective case
covering your iPod.
If you do not use an adapter or if the adapter is not
compatible, the connection could be loose or poor, which
could cause damage or malfunctions.
Connecting USB
Connect or remove your USB device whenever you want.
y
USB device is automatically charged when it is connected to the
unit, even if the unit is in standby mode.
This unit supports USB mass storage class devices (e.g., flash
memories or portable audio players) using FAT16 or FAT32
format.
Do not connect devices other than USB mass storage class
devices (such as USB chargers or USB hubs), PCs, card
readers, an external HDD, etc.
Connecting the DAB/FM antenna
(U.K. and Australia models)
Connecting the power cable
Indoor DAB/
FM antenna
To an AC wall
outlet
(Canada model)
Other connection
Note
Notes
Notes
Dock Adapter
iPod dock
10 En
Follow the procedures below to play back music.
*
1
Some features may not be available depending on the model or the software version of your iPod.
*
2
· Some devices may not work properly even if they meet the requirements.
· Playability of and power supply to all kind of USB devices are not guaranteed.
· The reading time may exceed 30 seconds depending on the number of files/folders.
· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made backup copies.
LISTENING TO MUSIC
Playback operation
Set the source
Switch the
input
Select music and start playback
iPod
*1
CD
USB
*2
AUX1
AUX2
1
2
3
P. 9
Dock
Adapter
P. 9
To AUX1 To AUX2
For operation, refer to the instruction
manuals supplied with external components
such as DVD player and portable player.
LISTENING TO MUSIC
11 En
OPERATION
English
Some features may not be compatible depending on the model or
the software version of your iPod.
Control playback
/ : Scroll buttons
MENU: Returns to the upper level in the iPod menu
ENTER: Select group/start playback
: Skip forward/press and hold to fast-forward
: Skip backward/press and hold to rewind
: Starts or pauses playback
For iPod (5th generation) and iPod nano (1st generation), you
can only operate the iPod menu using the front panel display.
There are some characters that cannot be displayed in the front
panel display of this unit.
Shuffle play
You can play back in random sequence.
*
1
You cannot set ALBUMS when you use an iPod touch.
Repeat play
You can play back repeatedly.
Control playback
: Stop
: Pause
: Play
: Rewind
: Fast forward
: Skip backward
: Skip forward
FOLDER / : Skip to the first file in the previous/next
folder for MP3 or WMA.
*
* If you press these buttons, the folder name is displayed on the
front panel display for a certain period.
y
You can also use the Numeric buttons to enter the number of
the song directly. To clear the entry, press CLEAR.
Playback for Data Disc starts in alphanumeric order of files.
Playback for USB starts in order by date and time of creation.
Shuffle play
You can play back in random sequence.
*
2
If the audio format of the selected music source is MP3/
WMA, you can also select FOLDER.
Operation for iPod
Note
Notes
1 2
During playback
iPod menu
Press repeatedly.
Operation for CD/USB
Notes
Press repeatedly.
1 2
During playback
Press repeatedly.
LISTENING TO MUSIC
12 En
Repeat play
You can play back repeatedly.
*
3
If the audio format of the selected music source is MP3/
WMA, you can also select FOLDER.
You can switch the playback information shown on the
front panel display. Some special characters may not be
shown properly.
For iPod
Song number and elapsed time (default setting)
Song number and remaining time
Song name
Artist name
Album name
Back to the default setting
This function is available for iPod (5th generation), iPod classic,
iPod nano, and iPod touch. However, even with these models,
this function may not be available depending on the software
version of your iPod.
For CD/USB
Track/file number and elapsed time of the current
song (default setting)
Track number and remaining time of the current
song
*4
Total time of the disc
*4
Remaining time of the disc
*4
File name
*5
Track name
*6
Artist name
*6
Album name
*6
Back to the default setting
*
4
Only for Audio CDs
*
5
Only for MP3/WMA files
*
6
Only when the selected track has information
This unit has built-in sound program which will
automatically adjusts music source to provide enjoyable
sound quality.
Bit data expansion
Bit data expansion increases CD 16-bit data to 24 bits,
achieving a more natural and detailed sound.
This function is only available for Audio CDs.
Music Enhancer
Music Enhancer feature enhances the sound for
compressed music by regenerating musical elements that
are lost through compression.
This function is not available for Audio CDs and audio input
from external device connected to AUX1.
Switching the display
Note
Press repeatedly.
Press repeatedly.
1 2
During playback
Playback sound
Note
Note
13 En
OPERATION
English
DAB (Digital Audio Broadcasting) uses digital signals for
clearer sound and more stable reception compared to
analog signals.
This unit can also receive DAB+ (an upgraded version of
DAB) that allows stations using MPEG-4 HE-AAC v2
audio codec, which has a more efficient transmission
method and provides higher sound than DAB.
Before tuning into DAB stations, an initial scan must be
performed. The initial scan starts automatically when you
select DAB as the input source for the first time.
y
You can also perform the initial scan manually by INIT SCAN
( P. 17, 19).
While the scan is in progress, “Scanning” and the
percentage of the progress of scan appear on the front
panel display.
When scanning is complete, the number of receivable
DAB stations appears on the front panel display for a
while, then the unit airs the first station as stored in station
order.
This unit can receive Band III (174 - 240 MHz) only.
Some stations have sub (secondary) stations. The
secondary indicator lights up when a secondary audio
station is selected.
y
You can change the order of DAB stations by STATION ORDER
( P. 17, 19).
When the unit cannot receive the DAB signal, “Off Air” is
displayed on the front panel display.
You can store your favorite DAB stations with the preset
function. The PRESET indicator lights up on the front
panel display ( P. 6).
y
You can preset up to 30 DAB stations.
To cancel the preset while choosing a preset number, press
MEMORY again.
You can delete a preset station by pressing OPTION S/T
ENTER to select PRESET DELETE.
LISTENING TO DAB STATIONS (U.K. and Australia models)
Preparing the DAB tuning
Note
Tuning DAB stations
Press repeatedly to select
the DAB mode.
Press repeatedly to
select the DAB mode.
Press TUNING and select a
DAB station.
1 2
Note
Presetting DAB stations
Selecting preset DAB stations
(Preset tuning)
Secondary indicator
Tune into a favorite
DAB station.
Press MEMORY.
Select the preset number
you want to store to.
Complete the preset.
1 2
3 4
Select the preset radio station in DAB
mode.
LISTENING TO DAB STATIONS (U.K. and Australia models)
14 En
STATION LABEL
Displays the name of the current DAB station and preset
number.
DLS (Dynamic Label Segment)
Displays information about the current DAB station, such as
the name of the song, artist and speaker, etc. This data is
continuously updated by the DAB broadcaster, thus changing
often with every new song or program.
Other data, such as news, weather, and sports headlines, may
be broadcast as well.
ENSEMBLE LABEL
Displays the name of the current ensemble.
PROGRAM TYPE
Displays the genre of the current DAB station.
TIME
Displays the current time.
BITRATE
Displays the bitrate of the current DAB station.
CHANNEL/FREQUENCY
Displays the channel label and frequency of the current DAB
station.
SIGNAL QUALITY
Displays signal reception quality (from 0 (none) to 100 (best))
of current DAB tuning.
AUDIO FORMAT
Displays the audio format of the current station, and whether
DRC (Dynamic Range Control)* is activated. “(DRC ON)” is
displayed when DRC MODE ( P. 17, 19) is set to AUTO
and DRC information is transmitted by DAB station.
* Some DAB broadcasters transmit a wide dynamic range
enabling high quality sound, accompanied by DRC
information.
Use this feature to compress the dynamic range of the DAB
broadcast. This is especially useful when you listen to a
DAB station in a noisy environment or at low volume at
night.
y
You can change the DRC setting by DRC MODE
( P. 17, 19).
Back to the STATION LABEL
Not all DAB broadcasters transmit station information.
This unit can receive Band III only.
DAB station information
Note
1 2
Press repeatedly.
While listening
DAB frequency information
Frequency Channel label
174.928 MHz 5A
176.640 MHz 5B
178.352 MHz 5C
180.064 MHz 5D
181.936 MHz 6A
183.648 MHz 6B
185.360 MHz 6C
187.072 MHz 6D
188.928 MHz 7A
190.640 MHz 7B
192.352 MHz 7C
194.064 MHz 7D
195.936 MHz 8A
197.648 MHz 8B
199.360 MHz 8C
201.072 MHz 8D
202.928 MHz 9A
204.640 MHz 9B
206.352 MHz 9C
208.064 MHz 9D
209.936 MHz 10A
211.648 MHz 10B
213.360 MHz 10C
215.072 MHz 10D
216.928 MHz 11A
218.640 MHz 11B
220.352 MHz 11C
222.064 MHz 11D
223.936 MHz 12A
225.648 MHz 12B
227.360 MHz 12C
229.072 MHz 12D
230.784 MHz 13A
232.496 MHz 13B
234.208 MHz 13C
235.776 MHz 13D
237.488 MHz 13E
239.200 MHz 13F
15 En
OPERATION
English
y
If the signal received from the station you want to select is weak,
you can also tune into radio stations manually by pressing
TUNING / repeatedly.
When receiving a stereo broadcasting station, you can switch
between stereo and monaural by pressing MONO.
You can store your favorite FM stations with the preset
function.
Automatic preset tuning
When you perform the automatic preset, all stored stations are
cleared and the new stations are stored.
Manual preset tuning
y
You can preset up to 30 FM stations.
To cancel the manual preset while choosing a preset number,
press MEMORY again.
You can delete a preset station by pressing OPTION S/T
ENTER to select PRESET DELETE.
PS (Program Service)
PTY (Program Type)
RT (Radio Text)
CT (Clock Time)
Frequency
Back to the PS
If the signal transmission of the Radio Data System station is too
weak, this unit may not be able to receive Radio Data System
information completely. In particular, RT (Radio Text)
information uses a lot of bandwidth, so it may be less available
compared to other types of information.
LISTENING TO FM RADIO STATIONS
Tuning to FM radio stations
Note
Presetting FM radio stations
Note
Press TUNER. Press and hold.
Automatic tuning starts.
1 2
d
d
d
d
Press and hold
MEMORY for more than
2 seconds in FM mode.
Start the automatic preset.
1 2
Tune into a favorite
radio station.
Press MEMORY.
Select the preset
number you want to
store to.
Complete the manual
preset.
1 2
3 4
Selecting preset FM radio stations
(Preset tuning)
Displaying Radio Data System
information (U.K. model only)
Note
Select the preset radio station
in FM mode.
1 2
Press repeatedly.
While listening
16 En
To set the clock, press and hold CLOCK or press
OPTION to enter CLOCK SET of the option menu.
As for the setting, refer to “Using option menu” on
page 17.
Once you set the clock, you can display the clock on the
front panel display.
When you press CLOCK while the power is on, the clock
is displayed on the front panel display for a few seconds.
When you press CLOCK during standby mode, you can
select whether to display the clock on the front panel
display or not.
This unit supports 24-hour clock display.
The clock setting will be lost if you disconnect the power cable
from the wall outlet for several minutes.
Using the timer
The timer sets the unit to play back music at the time you
set.
To set the timer, press and hold TIMER or press OPTION
to enter TIMER SET of the option menu.
As for the setting, refer to “Using option menu” on
page 17.
To use the timer, set the appropriate input source securely
and set the timer in the option menu in advance ( P. 18).
TIMER OFF: To set the timer off.
TIMER ONCE: To set the timer once.
TIMER EVERY: To set the timer everyday at the same
time.
When you switch the timer set to TIMER EVERY or
TIMER ONCE, the TIMER indicator lights up on the
front panel display.
The clock has to be set in advance.
When the timer is set, the TIMER indicator lights up on the
front panel display. While the power is on, the TIMER indicator
flashes as the set time of the timer becomes closer.
y
The settings set in timer settings are retained.
Using sleep timer
The sleep timer sets the unit to the standby mode after the
specified time elapses.
The SLEEP indicator lights up on the front panel display.
CLOCK AND TIMER
Using the clock
Notes
Using timer and sleep timer
Press CLOCK.
Press repeatedly.
Notes
Press repeatedly.
17 En
OPERATION
English
The option menu appears on the front panel display by pressing OPTION. You can set various useful functions with
option menu.
*
1
When DAB stations are not registered, these option menu do not appear.
*
2
For U.K. and Australia models.
Operation procedure
For DAB CLEAR, INIT SCAN, and TUNE AID, see page 19.
*
3
When there are some parameters to set, repeat steps 3 and 4. You can go back to a previous parameter by pressing .
*
4
To set additional items, repeat steps 2 to 5.
y
To cancel the setting during the operation, press OPTION.
Setting tone/balance
TREBLE
*5
: Adjusts the high frequency response.
BASS
*5
: Adjusts the low frequency response.
BALANCE: Adjusts the volume level of each left and right speaker channel.
*
5
Also effective when you are using headphones.
USING USEFUL FUNCTIONS
Using option menu
Option menu Parameter or control range Reference page
PRESET DELETE*
1
(Displays only when the input source is set to DAB/FM.) 13, 15
STATION ORDER*
1, 2
ALPHANUMERIC/ENSEMBLE
(Displays only when the input source is set to DAB.)
19
DRC MODE*
1, 2
AUTO/OFF
(Displays only when the input source is set to DAB.)
19
DAB CLEAR*
1, 2
(Displays only when the input source is set to DAB.) 19
INIT SCAN*
2
(Displays only when the input source is set to DAB.) 19
TUNE AID*
2
(Displays only when the input source is set to DAB.) 19
TREBLE –10 dB to +10 dB below
BASS –10 dB to +10 dB below
BALANCE L+5 - CENTER - R+5 below
AUTO CLOCK*
2
ON/OFF below
CLOCK SET Hour, minute below
TIMER SET
Time (hour, minute), sound (source, track or preset number), volume,
timer on (every/once)/off
18
Press OPTION. Select desired
option menu.
Confirm with
ENTER.
Change the settings. Complete the
setting.*
4
1 2 3 4 5
Repeat*
3
Exit option
menu.
6
USING USEFUL FUNCTIONS
18 En
Adjusting the clock
AUTO CLOCK: Automatic adjustment function is available for U.K. and Australia models only. To apply for this
function, set AUTO CLOCK to ON.
CLOCK SET: To set hour and minute, repeat steps 3 and 4 on page 17.
y
You can enter CLOCK SET directly by pressing and holding CLOCK when the unit is on.
When setting the clock, you can also use the Numeric buttons to enter the hour and minute. To confirm the entry, press ENTER.
To clear the entry, press CLEAR.
The current time appears on the front panel display for a certain period by pressing CLOCK when the unit is on.
The time setting will be lost if you disconnect the power cable from the wall outlet for several minutes.
Setting the timer
TIMER SET: To select the following setting items, repeat steps 3 and 4 on page 17.
y
You can enter TIMER SET directly by pressing and holding TIMER.
Note
Time (hour and minute)
y
You can use the Numeric buttons to enter the hour/minute, track/file number, preset number and volume when you are
setting the timer. To confirm the entry, press ENTER. To clear the entry, press CLEAR.
Input source and track/file number or preset number
If the source is not set properly, the timer sound will not be heard. Make sure that the source is set securely.
CD:
Set a track/file number.
If you set the track/file number which is not exist, the first track/file is played back automatically.
USB:
Set a file number.
If you set a file number that does not exist, the first file is played back automatically.
iPod:
When you select the iPod as a source, this unit resumes the music that you were listening to last time.
FM:
Set preset number.
By selecting “– – –”, the FM station you set last time is set.
DAB (U.K. and Australia models):
Set preset number.
By selecting “– – –”, the DAB station you set last time is set.
Volume
The volume level can be set between “1” - “MAX” (60) and “– – –”
*
. When the timer is set while the unit is in
standby mode, the volume is set at this point is used. When the timer is executed while the unit is on, the
volume level remains the same as the current volume.
* If you set your volume to “_ _ _” when the timer is set while the unit is in standby mode, the volume level is set at the
same level as input source.
Timer on (TIMER EVERY/TIMER ONCE)/Timer off (TIMER OFF)
Switch the timer to TIMER EVERY/TIMER ONCE/TIMER OFF. When the timer is set to TIMER EVERY or
TIMER ONCE, the TIMER indicator lights up on the front panel display.
y
This setting is also available with TIMER (p. 16).
Note
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Yamaha MCR-550 Le manuel du propriétaire

Catégorie
Récepteurs AV
Taper
Le manuel du propriétaire

dans d''autres langues