PRESIDENT JOHNSON II Le manuel du propriétaire

Owner’s manual / Manuel d’utilisation

Manual del usuario / Manual do usuário

12/24 V

with / avec / con / com

Downloaded from www.cbradio.nl

Votre PRESIDENT JOHNSON II USA 12/24 V en un coup d’œil

Uma olhada no seu JOHNSON II USA 12/24 VUn vistazo a vuestro PRESIDENT JOHNSON II USA 12/24 V

Your PRESIDENT JOHNSON II USA 12/24 V at a glance

3

SOMMAIRE

INSTALLATION 18

UTILISATION 21

CARACTÉRISTIQUES TECHNIQUES 26

GUIDE DE DÉPANNAGE 27

COMMENT ÉMETTRE OU RECEVOIR UN MESSAGE 27

GLOSSAIRE 28

GARANTIE 30

TABLEAUX DES FRÉQUENCES 59

SUMÁRIO

INSTALAÇÃO 46

UTILIZAÇÃO 48

CARACTERÍSTICAS TÉCNICAS 54

GUIA DE PROBLEMAS 55

COMO TRANSMITIR OU RECEBER UMA MENSAGEM 55

GLOSSÁRIO 55

GARANTIA 58

TABELAS DE FREQUÊNCIAS 59

SUMARIO

INSTALACIÓN 32

UTILIZACIÓN 35

CARACTERÍSTICAS TÉCNICAS 40

GUÍA DE PROBLEMAS 41

COMO EMITIR O RECIBIR UN MENSAJE 41

LÉXICO 42

GARANTÍA 44

TABLAS DE FRECUENCIAS 59

SUMMARY

INSTALLATION 5

HOW TO USE YOUR CB 7

TECHNICAL CHARACTERISTICS 13

TROUBLE SHOOTING 13

HOW TO TRANSMIT OR RECEIVE A MESSAGE 14

GLOSSARY 14

WARRANTY 16

FREQUENCY TABLES 59

English

Français

Português

Español

4

WARNING !

Before using, be careful never to transmit without ﬁrst

having connected the antenna (connection “B” situated

on the back panel of the equipment) or without having

set the SWR (Standing Wave Ratio) ! Failure to do so may

result in destruction of the power ampliﬁer, which is not

covered by the warranty.

The warranty of this transceiver is valid only in the country of purchase.

English

PROPOSITION 65 WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.

5

English

Welcome to the world of the new generation of CB ra-

dios. The new PRESIDENT range gives you access to top

performance CB equipment. With the use of up-to-date

technology, which guarantees unprecedented quality,

your PRESIDENT JOHNSON II USA 12/24 V is a new step

in personal communication and is the surest choice for

the most demanding of professional CB radio users. To

ensure that you make the most of all its capacities, we

advise you to read carefully this manual before installing

and using your PRESIDENT JOHNSON II USA 12/24 V.

A) INSTALLATION

1) WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO

a) You should choose the most appropriate setting from a

simple and practical point of view.

b) Your CB radio should not interfere with the driver or the

passengers.

c) Remember to provide for the passing and protection of

different wires (e.g. power, antenna, accessory cabling)

so that they do not in any way interfere with the driving of

the vehicle.

d) To install your equipment, use the cradle (1) and the self-tap-

ping screws (2) provided (drilling diameter 3.2 mm). Take

care not to damage the vehicle’s electrical system while

drilling the dash board.

e) Do not forget to insert the rubber joints (3) between the

CB and its support as these have a shock-absorbing effect

which permits gentle orientation and tightening of the set.

f) Choose where to place the microphone support and

remember that the microphone cord must stretch to the

driver without interfering with the controls of the vehicle.

- N.B. : As the transceiver has a frontal microphone socket, it

can be set into the dash board. In this case, you will need

to add an external loud speaker to improve the sound

quality of communications (connector EXT.SP. situated on

the back panel: C). Ask your dealer for advice on mounting

your CB radio.

MOUNTING DIAGRAM

6

2) ANTENNA INSTALLATION

a) Choosing your antenna

- For CB radios, the longer the antenna, the better its results.

Your dealer will be able to help you with your choice of

antenna.

b) Mobile antenna

- Must be ﬁxed to the vehicle where there is a maximum of

metallic surface (ground plane), away from windscreen

mountings.

- If you already have a radio-telephone antenna installed,

the CB antenna should be higher than this.

- There are two types of antenna: pre-regulated which

should be used on a good ground plane (e.g. car roof or

lid of the boot), and adjustable which offer a much larger

range and can be used on a smaller ground plane (see §

ADJUSTMENT OF SWR page 7).

- For an antenna which must be ﬁxed by drilling, you will need

a good contact between the antenna and the ground

plane. To obtain this, you should lightly scratch the surface

where the screw and tightening star are to be placed.

- Be careful not to pinch or ﬂatten the coaxial cable (as this

runs the risk of break down and/or short-circuiting).

- Connect the antenna (B).

c) Fixed antenna

- A ﬁxed antenna should be installed in a clear a space as

possible. If it is ﬁxed to a mast, it will perhaps be necessary

to stay it, according to the laws in force (you should seek

professional advice). All PRESIDENT antennas and acces-

sories are designed to give maximum efﬁciency to each

CB radio within the range.

3) POWER CONNECTION

Your PRESIDENT JOHNSON II USA 12/24 V is protected against

an inversion of polarities. However, before switching it on, you

are advised to check all the connections. Your equipment

must be supplied with a continued current of 12 or 24 volts

(A). Today, most cars and lorries are negative earth. You

can check this by making sure that the negative terminal

of the battery is connected either to the engine block or

to the chassis. If this is not the case, you should consult your

dealer.

a) Check that the battery is of 12 or 24 volts.

b) Locate the positive and negative terminals of the battery

(+ is red and - is black). Should it be necessary to lengthen

the power cable, you should use the same or a superior

type of cable.

OUTPUT

RADIUS

PATTERN

English

7

c) It is necessary to connect your CB to a permanent (+) and

(-). We advise you to connect the power cable directly to

the battery (as the connection of the CB cable to the wiring

of the car-radio or other parts of the electrical circuit may,

in some cases, increase the likelihood of interference).

d) Connect the red wire (+) to the positive terminal of the

battery and the black (-) wire to the negative terminal of

the battery.

e) Connect the power cable to your CB radio.

WARNING: Never replace the original fuse (2 A) by one of

a different value.

4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING

YOUR SET FOR THE FIRST TIME (without transmitting

and without using the “push-to-talk” switch on the

microphone)

a) Connect the microphone

b) Check the antenna connections

c) Turn the set on by turning the volume knob (1) clockwise.

d) Turn the squelch SQ knob (2) to minimum (M position).

e) Adjust the volume to a comfortable level.

f) Go to channel 20 by using s, t, UP or DN keys (4, 5, 15,

14).

5) ADJUSTMENT OF SWR (Standing wave ratio)

WARNING: This must be carried out when you use your

CB radio for the ﬁrst time (and whenever you re-position

your antenna). The adjustment must be carried out in an

obstacle-free area.

Adjustment with external SWR-meter (e.g. TOS-1 PRESIDENT)

a) To connect the SWR meter :

- Connect the SWR meter between the CB radio and the

antenna as close as possible to the CB (use a maximum

of 15.75 inches (40 cm) cable, type President CA 2C).

b) To adjust the SWR meter:

- Set the CB to channel 20.

- Put the switch on the SWR-meter to position FWD (calibra-

tion).

- Press the “push-to-talk” switch on the microphone to trans-

mit.

- Bring the index needle to t by using the calibration key.

- Change the switch to position REF (reading of the SWR level).

The reading on the Meter should be as near as possible to

1. If this is not the case, re-adjust your antenna to obtain a

reading as close as possible to 1. (A SWR reading between

1 and 1.8 is acceptable).

- It will be necessary to re-calibrate the SWR meter after

each adjustment of the antenna.

WARNING: In order to avoid any losses and attenuations

in cables used for connection between the radio and its

accessories, PRESIDENT recommends to use a cable with

a length inferior to 118.11 inches (3 m).

Adjustment with internal SWR-meter

Short press •F/MEM key (6) and s (4) or UP (14) key to switch

on (/off) the SWR function (see § •SWR page 8). SWR

level is displayed. When ﬁnished, switch off the function.

Your CB is now ready for use.

B) HOW TO USE YOUR CB

1) ON/OFF – VOLUME

a) To turn the set on, turn the VOL knob (1) clockwise.

b) To increase the sound level, turn the same knob further

clockwise.

English

8

2) ASC (Automatic Squelch Control) / SQUELCH

Suppresses undesirable background noises when there

is no communication. Squelch does not affect neither

sound nor transmission power, but allows a considerable

improvement in listening comfort.

a) ASC: AUTOMATIC SQUELCH CONTROL

Worldwide patent, a PRESIDENT exclusivity.

Turn the SQ knob (2) anti-clockwise into ASC position.

appears on the display. No repetitive manual adjustment

and a permanent improvement between the sensitivity

and the listening comfort when ASC is active. This function

can be disconnected by turning the switch clockwise. In

this case the squelch adjustment becomes manual again.

disappears from the display.

b) MANUAL SQUELCH

Turn the SQ knob clockwise to the exact point where all

background noise disappears. This adjustment should be

done with precision as, if set to maximum (fully clockwise),

only the strongest signals will be received.

3) DISPLAY

It shows all functions:

The BARGRAPH shows the reception level and the output

power level.

4) CHANNEL SELECTOR s ~ TALKBACK LEVEL s~ •SWR

CHANNEL SELECTOR s on unit

(short press)

s key (4) allows increasing a channel. A beep sounds

each time the channel changes if the KEY BEEP function

is activated. (See KEY BEEP function page 12).

You can also use UP key (14) on the microphone.

TALKBACK LEVEL s (PTT + short press)

TALKBACK function lets you monitor yourself when trans-

mitting. Setting the level active automatically the function.

See page 13.

Press ﬁrst PTT switch (12) and then s key (4) to increase

TALKBACK level from actual level to 9 (max.). The level is

displayed for 3 seconds if the PTT switch (12) is not released.

•SWR (•F/MEM + short press)

Short press •F/MEM key (6) and s key (4) to switch on/off

the SWR function. SWR level is displayed when function is

on.

5) CHANNEL SELECTOR t ~ TALKBACK LEVEL t ~ •LOCAL

CHANNEL SELECTOR t on unit

(short press)

t key (5) allows decreasing a channel. A beep sounds

each time the channel changes if the KEY BEEP function

is activated. See KEY BEEP function page 12.

You can also use the DN key (15) on the microphone.

TALKBACK LEVEL t (PTT + short press)

TALKBACK function lets you monitor yourself when trans-

mitting. Setting the level active automatically the function.

See page 13.

English

9

Press ﬁrst PTT switch (12) and then t key (5) to decrease

TALKBACK level from actual level to 1 (min.). The level is

displayed for 3 seconds if the PTT switch (12) is not released.

•LOCAL (•F/MEM + short press)

Press •F/MEM (6) and t key (5) to activate/deactivate.

“LOCAL” is displayed when the function is on.

This feature allows a better listening through close contact.

When your partner is close, active this function to avoid

distortion.

6) •F/MEM ~ DW ~ •COLOR

•F/MEM

(short press)

Short press this key to enter in mode FUNCTION. blinks

when the function is on.

automatically disappears after

10 seconds without pressing any key.

For memories, see § MEMORY page 12.

DW (long press)

Press and hold the DW key (6) for 1 second to activate/

deactivate the DUAL WATCH function. When function in

on, “DW” is displayed. This function lets you watch over

channel 9 or 19 and the channel you are using. The ﬁrst

long press activates the DW function between channel 9

and the busy channel. A new press activates the function

between channel 19 and the busy channel. The number

of the selected channel, the memorized channel includ-

ed, and channel 9 or 19 are alternately displayed. “EMG”

is also displayed at the same time as channel 9 or 19. The

selected channel can be modiﬁed during the dual watch.

A new long press on DW key (6) disables the DW function.

•COLOR (•F/MEM + long press)

Press one time the •F/MEM key (6) and press and hold the

•COLOR key (6) for 1 second to alternate between 3 colors:

Green -> Blue -> Orange

7) 9/19 ~ HI-CUT ~ •M3

9/19

(short press)

Channels 9 and 19 are automatically selected by pressing

this key. A push activates channel 9, “EMG” is displayed. A

second push activates channel 19 “EMG” is displayed. A

new push returns to the previous channel, “EMG”disappears.

HI-CUT (long press)

HI-CUT eliminates high frequency interferences. Has to be

used in accordance with the reception conditions. “HI-CUT”

appears on the display when the HI-CUT ﬁlter is activated.

•M3

See § MEMORY page 12.

8) ANL/NB ~ SCAN ~ •M2

ANL/NB

(short press)

ANL/Automatic Noise Limiter ﬁlter reduces back ground

noises and some reception interferences.

NB/Noise Blanker ﬁlter suppress an ignition noise in the

reception.

Short press ANL/NB key (8) key to alternate the 4 positions

switch: • ANL and NB off • ANL on / NB off • ANL off / NB

on • ANL and NB on.

When a ﬁlter is active, it name “ANL” or/and “NB”, is dis-

played on the LCD.

SCAN (long press)

CB MODE

Press and hold SCAN key (8) for 1 second to activate SCAN

function (for CB channels) in an increasing way. “SCAN”

English

10

is displayed. The scanning stops as soon as there is a busy

channel. The scanning automatically starts 3 seconds

after the end of the transmission and no key is activated

during 3 s. The scanning starts again in an increasing way

by pressing s (4) or UP (14) key, or in a decreasing way

by pressing t (5) or DN (15) key.

While scanning, press •F/MEM key (6) to alternate between

All Channel Scan and Memory Channel Scan.

In Memory Scan Channel mode, channel 9, channel 19

and the memorised channels are scanned.

Press PTT switch (12), 9/19 key (7) , DW key (6) or long press

SCAN key (8) again to exit SCAN function.

WX MODE

Press and hold the SCAN key (8) for 1 second to activate

the SCAN function (for WEATHER channels) in an increas-

ing way. “SCAN” is displayed. The scanning stops as soon

as there is a busy channel. The scanning automatically

starts 3 seconds after the end of the transmission and no

key is activated during 3 s. The scanning starts again in

an increasing way by pressing s (4) or UP (14) key, or in a

decreasing way by pressing t (5) or DN (15) key.

Note: If the ALERT function is activated, the SIREN tone

sounds (see § ALERT below) when a tone is detected in the

selected WEATHER channel only. Use ﬁrst SCAN function in

WX mode to detect tones in all the WEATHER channels.

A new long press on SCAN disables the SCAN function.

•M2

See § MEMORY page 12.

9) WX ~ ALERT ~ •M1

WX (WEATHER MODE)

(short press)

CB functions are not allowed in WX mode. If user presses

a not allowed key and KEY BEEP function is activated, the

radio sounds error tone.

Press WX key (9) in order to activate the WX mode. “WX”

appears on the display. A new short press on WX key (9)

disables the WX mode “WX” disappears.

The WX mode allows to hear weather information. When

the mode is activated, use s/t key (4/5) or UP/DN key

(14/15) on the microphone to move through the 7 weather

channels to ﬁnd the active channel in your local area.

The display shows the selected weather channel and if the

unit receives a signal, “WX” and “ALERT” icons blink.

ALERT (long press)

The SIREN tone only sounds in CB and PA mode. It does not

sound in WX mode.

Press and hold the ALERT key (9) for 1 second to activate/

deactivate the ALERT function. When the function is on and

a tone is detected at the selected weather channel, then

the unit sounds SIREN tone. “ALERT” and the “WX channel”

blink on the display. The unit cancel CB or PA mode and

go to WX mode.

During a SIREN tone sound, press any key to stop the sound,

“ALERT” and the “WX channel” stop blinking on the display.

Note: The SIREN tone sounds when ALERT is detected in the

selected WEATHER channel only. Use ﬁrst SCAN function in

WX mode (see § WX MODE above) to detect tones in all

the WEATHER channels.

•M1

See § MEMORY page 12.

10) CB/PA ~ LOCK ~ •VOX ~ •VOX SET

CB/PA

(short press)

Short press CB/PA key (10) to alternate between CB and

PA mode.

English

11

PA MODE

An external loud speaker can be connected to the unit by

the PA jack plug situated on the back panel PA.SP. (D). The

PA volume is regulated by VOL knob (1). “PA” is displayed.

ROGER, SCAN, MEM, VOX are not allowed in PA mode. If the

user set on PA mode while SCAN function, instant channel

9/19 mode or WX mode, these are canceled.

The CB message received will be directed towards the PA

speaker and be ampliﬁed.

The message transmitted into the microphone will be di-

rected towards the PA speaker and be ampliﬁed. “PAon”

is displayed, Meter numbers indicate signal level.

LOCK (long press)

Allows to lock all the keys on the front panel. if the KEY BEEP

function is on, an error beep sounds when a key is used.

A long press on LOCK key (10) activates/deactivates the

LOCK function. appears on the display when the function

is activated.

Transmission (microphone or vox) and reception remain

active.

•VOX (•F/MEM + short press)

The VOX function allows transmitting by speaking into the

original microphone (or in the optional vox microphone)

without pressing the PTT switch (12). The use of an optional

vox microphone connected to the rear panel of the trans-

ceiver (E) disables the original microphone.

Press one time •F/MEM key (6) and short press •VOX key

(10) in order to activate the VOX function. “VOX” appears

on the display. Repeat the key combination to disable the

function. “VOX” disappears.

•VOX SET (•F/MEM + long press)

Press one time the •F/MEM key (6) and press during 1 second

•VOX key (10) in order to activate the function VOX SETTING.

Three adjustments are possible: Sensitivity / Anti-vox level

/ Vox delay time . Press shortly •VOX (10) in order to go

to the following adjustment (looping , , ).

The display shows the type of adjustment followed by its

level.

- Sensitivity : allows the adjustment of the microphone

(original one or optional vox) for an optimum transmission

quality. Adjustable level from 1 (high level) to 9 (low level)

by pressing s/t (4/5) or UP/DN (14/15) keys . corresponds

to the Sensitivity Level.

- Anti-Vox

: allows disabling the transmission generated by

the surrounding noise. The level is adjustable from 0 (Off) to

9 (low level) by pressing s/t (4/5) or UP/DN (14/15) keys.

corresponds to Anti-vox Level.

- Delay time

: allows avoiding the sudden cut of the trans-

mission by adding a delay at the end of speaking. The

level is adjustable from 1 (short delay) to 9 (long delay) by

pressing s/t (4/5) or UP/DN (14/15) keys. corresponds

to Delay Time.

Once the adjustments are done, short press •F/MEM key

(6) key in order to quit the Vox Adjustment mode.

When VOX SETTING is done the VOX function is automati-

cally ON. “VOX” appears on the display.

11) 6 PIN MICROPHONE PLUG

The plug is located on the front panel of the transceiver and

makes the setting of the equipment into the dashboard

easier.

See cabling diagram page 60.

English

12

12) PTT

Transmission key, press to transmit a message, is displayed

and release to listen to an incoming communication.

14) CHANNEL SELECTOR UP on microphone

UP key (14) allows increasing a channel. A beep sounds

each time the channel changes if the KEY BEEP function

is activated (see KEY BEEP function below).

You can also use s key (4) on the unit.

15) CHANNEL SELECTOR DN on microphone

DN key (15) allows decreasing a channel. A beep sounds

each time the channel changes if the KEY BEEP function

is activated (see KEY BEEP function below).

You can also use t key (5) on the unit.

ROGER BEEP

Start the unit while pressing s (4) or UP (14) key to activate

the ROGER BEEP function. A beep sounds if KEY BEEP function

is on.

The icon “ ” appears on the display when the function is

active. The Roger Beep sounds when the PTT switch (12) of

the microphone is released in order to let your correspond-

ent speak. Historically as CB is a “simplex” communication

mode, it is not possible to speak and to listen at the same

time (as it is the case with a telephone). Once someone

had ﬁnished talking, he said “Roger” in order to prevent his

correspondent that it was his turn to talk. The word “Roger”

has been replaced by a signiﬁcant beep. There comes

“Roger beep” from.

Note: the Roger beep also sounds in the loudspeaker if the

KEY BEEP function is active. If the KEY BEEP function is not

active, only the correspondent can hear the Roger Beep.

In PA mode the function is not allowed.

KEY BEEP

Beep on changing the channel, keys etc...

Start the unit while pressing t (5) or DN (15) key to activate

the KEY BEEP function. A beep sounds. “BP” is displayed.

Start again the unit while pressing t (5) or DN (15) key to

deactivate the KEY BEEP function. “BP” disappears.

MEMORY

This CB radio allows to memorize 3 channels with following

parameters: ANL (on/off), NB (on/off), HI-CUT (on/off).

To recall a memory:

(short press)

- Short press •F/MEM key (6). If the KEY BEEP function is acti-

vated a beep sounds.

- Short press •M1 (9), •M2 (8) or •M3 (7) key to recall the

selected memory.

“MEM” and the number of the memory (1, 2 or 3) appears

on the display

To memorize:

(long press)

- Select the channel and parameters to be memorized.

- Short press •F/MEM key (6). If the KEY BEEP function is acti-

vated a beep sounds.

- Press •M1 (9), •M2 (8) or •M3 (7) key during 1 second to

store the selected channel into memory. “MEM” appears.

- If the KEY BEEP function is activated a long beep conﬁrms

the saving.

To delete a memory:

- Switch off the transceiver.

- Keep the memory key •M1 (9), •M2 (8) or •M3 (7) pressed

and switch on the transceiver.

- The selected memory is deleted. “MEM” disappears.

English

13

TALKBACK FUNCTION (PTT + •F/MEM )

Press ﬁrst PTT switch (12) and then •F/MEM key (6) to acti-

vate/deactivate TALKBACK function. When the function is

on, “TALKBACK” is displayed.

TOT (Time Out Timer)

If the transmission (using the PTT (12) key or VOX) is more

than 5 minutes, CHANNEL and starts blinking, the trans-

mission ends.

The time-out tone will sound until the PTT key is released.

A) DC-POWER TERMINAL (13,8 V / 27,6 V)

B) ANTENNA CONNECTOR (SO-239)

C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3,5 mm)

D) PA SPEAKER JACK (

8 Ω, Ø 3,5 mm)

E) JACK FOR OPTIONAL VOX MIKE (Ø 2.5 mm)

C) TECHNICAL CHARACTERISTICS

1) GENERAL

- Channels : 40

- Modulation modes : AM

- Frequency ranges : from 26.965 MHz to 27.405 MHz

- Weather channels : from 162.400 MHz to 162.550 MHz

- Antenna impedance : 50 ohms

- Power supply : 13.8 V / 27.6 V

- Dimensions (W x D x H) : 6.69 x 5.91 x 2.05 inches

170 x 150 x 52 mm

- Weight : 2.20 lbs / 1 kg

- Accessories supplied : Ultra light electret microphone with

support, mounting cradle, screws

2) TRANSMISSION

- Frequency allowance : +/- 200 Hz

- Carrier power : 4 W (constant)

- Transmission interference : inferior to -60 dBc

- Audio response : 300 Hz to 3 KHz

- Emitted power in the adj.

channel : inferior to 20 µW

- Microphone sensitivity : 3 mV

- Drain : 2 A (with modulation)

- Modulated signal distortion : 1.8 %

3) RECEPTION

- Maxi. sensitivity at

10 dB (S+N)/N : 0.6 µV - 111 dBm

- Frequency response : 300 Hz to 3 kHz

- Adjacent channel selectivity : > 60 dB

- Maximum audio power : 2 W

- Squelch sensitivity : minimum 0.2 µV - 120 dBm

maximum 1 mV - 47 dBm

- Frequency image rejection

rate : 60 dB

- Intermediate frequency

rejection rate : 70 dB

- Drain : 300 mA nominal / 1000 mA maximum

D) TROUBLE SHOOTING

1) YOUR CB RADIO WILL NOT TRANSMIT OR YOUR

TRANSMISSION IS OF POOR QUALITY

- Check that the antenna is correctly connected and that

the SWR is properly adjusted.

- Check that the microphone is properly plugged in.

English

14

2) YOUR CB RADIO WILL NOT RECEIVE OR RECEPTION IS

POOR

- Check that LOCAL function is off.

- Check that the squelch level is properly adjusted.

- Check that the volume is set to a comfortable listening

level.

- Check that the antenna is correctly connected and that

the SWR is properly adjusted.

3) YOUR CB WILL NOT LIGHT UP

- Check the power supply.

- Check the connection wiring.

- Check the fuse.

E) HOW TO TRANSMIT OR RECEIVE A

MESSAGE

Now that you have read the manual, make sure that your

CB Radio is ready for use (i.e. check that your antenna is

connected).

Press the “push-to-talk” switch and announce your message

“Attention stations, transmission testing” which will allow

you to check the clearness and the power of your signal.

Release the switch and wait for a reply. You should receive

a reply like, “Strong and clear”.

If you use a calling channel (19) and you have established

communication with someone, it is common practice to

choose another available channel so as not to block the

calling channel.

F) GLOSSARY

Below you will ﬁnd some of the most frequently used CB radio

expressions. Remember this is meant for fun and that you

are by no means obliged to use them. In an emergency,

you should be as clear as possible.

INTERNATIONAL PHONETIC ALPHABET

A Alpha H Hotel O Oscar V Victor

B Bravo I India P Papa W Whiskey

C Charlie J Juliett Q Quebec X-ray

D Delta K Kilo R Romeo Y Yankee

E Echo L Lima S Sierra Z Zulu

F Foxtrott M Mike T Tango

G Golf N November U Uniform

TECHNICAL VOCABULARY

AM : Amplitude Modulation

CB : Citizen’s Band

CH : Channel

CW : Continuous Wave

DX : Long Distance Liaison

DW : Dual Watch

FM : Frequency Modulation

GMT : Greenwich Meantime

HF : High Frequency

LF : Low Frequency

LSB : Lower Side Band

RX : Receiver

SSB : Single Side Band

SWR : Standing Wave Ratio

SWL : Short Wave Listening

SW : Short Wave

TX : CB Transceiver

English

15

UHF : Ultra High Frequency

USB : Upper Side Band

VHF : Very High Frequency

CB LANGUAGE

Advertising : Flashing lights of police car

Back off : Slow down

Basement : Channel 1

Base station : A CB set in ﬁxed location

Bear : Policeman

Bear bite : Speeding ﬁne

Bear cage : Police station

Big slab : Motorway

Big 10-4 : Absolutely

Bleeding : Signal from an adjacent channel

interfering with the

transmission

Blocking the channel : Pressing the PTT switch without talking

Blue boys : Police

Break : Used to ask permission to join a

conversation

Breaker : A CBer wishing to join a channel

Clean and green : Clear of police

Cleaner channel : Channel with less interference

Coming in loud and

proud : Good reception

Doughnut : Tyre

Down and gone : Turning CB off

Down one : Go to a lower channel

Do you copy? : Understand?

DX : Long distance

Eighty eights : Love and kisses

Eye ball : CBers meeting together

Good buddy : Fellow CBer

Hammer : Accelerator

Handle : CBer’s nickname

Harvey wall banger : Dangerous driver

How am I hitting you? : How are you receiving me?

Keying the mike : Pressing the PTT switch without talking

Kojac with a kodak : Police radar

Land line : Telephone

Lunch box : CB set

Man with a gun : Police radar

Mayday : SOS

Meat wagon : Ambulance

Midnight shopper : Thief

Modulation : Conversation

Negative copy : No reply

Over your shoulder : Right behind you

Part your hair : Behave yourself - police ahead

Pull your hammer back : Slow down

Rat race : Congested trafﬁc

Rubberbander : New CBer

Sail boat fuel : Wind

Smokey dozing : Parked police car

Smokey with a camera : Police radar

Spaghetti bowl : Interchange

Stinger : Antenna

Turkey : Dumb CBer

Up one : Go up one channel

Wall to wall : All over/everywhere

What am I putting to

you? : Please give me an S-meter reading

English

16

• Transceivers which have been modified. The warranty application is excluded

in case of modification or poor maintenance done by a third party not approved

by PRESIDENT ELECTRONICS.

If you note a malfunction:

• Check the power supply of your device and the quality of the fuse.

• Check that the antenna, the microphone are correctly connected.

• Check that the squelch level is properly adjusted; the programmed configuration

is the correct one.

• In the event of a real malfunction, please contact your dealer first. He will decide

what action should be taken.

In case of an intervention not covered by warranty, an estimate will be established

before any repair.

Thank you for your confidence in the PRESIDENT quality and experience. We

recommend that you read this manual carefully so that you are completely satisfied

with your purchase.

Technical Manager

and

Quality Manager

This device is guaranteed 2 years parts and labour in its country of purchase

against any manufacturing defects validated by our technical department. PRES-

IDENT After Sales Service department reserves the right not to apply the warranty

in the event a breakdown is caused by an antenna other than those distributed by

PRESIDENT. An extension of 3 years warranty is proposed systematically for the

simultaneous purchase of a device and a PRESIDENT antenna, bringing the total

duration of the warranty to 5 years. In order to be valid, the warranty registration

must be completed and submitted within a period of 30 days after the purchase

date to PRESIDENT ELECTRONICS online at

www.president-electronics.

us/warranty-registration

. You can also access this warranty registration page

by using your smartphone to read (application must be available) the QR code on

the enclosed warranty card. You will receive a confirmation email if the registration

is successfully completed. Please keep a copy of this email for your records.

Any repair under warranty will be without charge and the return delivery costs will

be borne by PRESIDENT. A proof of purchase sales receipt must be included with

the device to be repaired. The dates listed on the warranty registration and proof

of purchase must match. In case the device is not under warranty, the repair and

return of the device will be charged.

No spare parts will be sent nor exchanged by PRESIDENT under warranty. Do

not proceed with the installation of the device without reading the user manual.

The warranty is only valid in the country of purchase.

Exclusions (not covered by Warranty):

• Damages caused by accident, shock or inadequate packaging.

• Power transistors, microphones, lights, fuses and the disrespect of the instal-

lation and use of specifications (including but not limited to antenna used with

too high power, final output power transistors (SWR), inversion of polarities, bad

connections, over voltage…).

• The warranty cannot be extended due to the non-availability of the device while

it is being serviced at PRESIDENT After Sales Service department, nor by a

change of one or more components or spare parts.

GENERAL WARRANTY CONDITIONS

English

17

Français

ATTENTION !

Avant toute utilisation, prenez garde de ne jamais émettre

sans avoir branché l’antenne (connecteur B situé sur la

face arrière de l’appareil), ni réglé le TOS (Taux d’Ondes

Stationnaires) ! Sinon, vous risquez de détruire l’ampliﬁ-

cateur de puissance, ce qui n’est pas couvert par la

garantie.

La garantie de ce poste est valable uniquement dans le pays d’achat.

AVERTISSEMENT PROPOSITION 65: Ce produit contient un produit chimique connu dans l’État de Californie pour provoquer des cancers et des malformations congénitales ou d’autres problèmes de reproduction.

18

Bienvenue dans le monde des émetteurs-récepteurs

CB de la dernière génération. Cette nouvelle gamme

de postes vous fait accéder à la communication élec-

tronique la plus performante. Grâce à l’utilisation de

technologies de pointe garantissant des qualités sans

précédent, votre PRESIDENT JOHNSON II USA 12/24 V est

un nouveau jalon dans la convivialité et la solution par

excellence pour le pro de la CB le plus exigeant. Pour

tirer le meilleur parti de toutes ses possibilités, nous vous

conseillons de lire attentivement ce mode d’emploi

avant d’installer et d’utiliser votre CB PRESIDENT JOHN-

SON II USA 12/24 V.

A) INSTALLATION

1) CHOIX DE L’EMPLACEMENT ET MONTAGE DU POSTE

MOBILE

a) Choisissez l’emplacement le plus approprié à une utilisation

simple et pratique de votre poste mobile.

b) Veillez à ce qu’il ne gêne pas le conducteur ni les passagers

du véhicule.

c) Prévoyez le passage et la protection des différents câbles,

(alimentation, antenne, accessoires...) aﬁn qu’ils ne vien-

nent en aucun cas perturber la conduite du véhicule.

d) Utilisez pour le montage le berceau (1) livré avec l’appa-

reil, ﬁxez-le solidement à l’aide des vis auto taraudeuse (2)

fournies (diamètre de perçage 3,2 mm). Prenez garde de

ne pas endommager le système électrique du véhicule

lors du perçage du tableau de bord.

e) Lors du montage, n’oubliez pas d’insérer les rondelles de

caoutchouc (3) entre le poste et son support. Celles-ci

jouent en effet un rôle «d’amortisseur» et permettent une

orientation et un serrage en douceur du poste.

f) Choisissez un emplacement pour le support du micro et

prévoyez le passage de son cordon.

- NOTA : Votre poste mobile possédant une prise micro en

façade peut être encastré dans le tableau de bord. Dans

ce cas, il est recommandé d’y adjoindre un haut-parleur

externe pour une meilleure écoute des communications

(connecteur EXT.SP. situé sur la face arrière de l’appareil :

C). Renseignez-vous auprès de votre revendeur le plus

proche pour le montage sur votre appareil.

SCHÉMA GÉNÉRAL DE

MONTAGE

Français

19

2) INSTALLATION DE L’ANTENNE

a) Choix de l’antenne

- En CB, plus une antenne est grande, meilleur est son ren-

dement. Votre Point Conseil saura orienter votre choix.

b) Antenne mobile

- Il faut l’installer à un endroit du véhicule où il y a un maximum

de surface métallique (plan de masse), en s’éloignant des

montants du pare-brise et de la lunette arrière.

- Dans le cas où une antenne radiotéléphone est déjà ins-

tallée, l’antenne CB doit être au-dessus de celle-ci.

- Il existe 2 types d’antennes : les préréglées et les réglables.

- Les préréglées s’utilisent de préférence avec un bon plan

de masse (pavillon de toit ou malle arrière).

- Les réglables offrent une plage d’utilisation beaucoup plus

large et permettent de tirer parti de plans de masse moins

importants (voir § RÉGLAGE DU TOS page 20).

- Pour une antenne à ﬁxation par perçage, il est nécessaire

d’avoir un excellent contact antenne/plan de masse ; pour

cela, grattez légèrement la tôle au niveau de la vis et de

l’étoile de serrage.

- Lors du passage du câble coaxial, prenez garde de ne pas

le pincer ou l’écraser (risque de rupture ou de court-circuit).

- Branchez l’antenne (B).

c) Antenne fixe

- Veillez à ce qu’elle soit dégagée au maximum. En cas de

ﬁxation sur un mât, il faudra éventuellement haubaner

conformément aux normes en vigueur (se renseigner auprès

d’un professionnel). Les antennes et accessoires PRESIDENT

sont spécialement conçus pour un rendement optimal de

chaque appareil de la gamme.

3) CONNEXION DE L’ALIMENTATION

Votre PRESIDENT JOHNSON II USA 12/24 V est muni d’une

protection contre les inversions de polarité. Néanmoins,

avant tout branchement, vériﬁez vos connexions.

Votre poste doit être alimenté par une source de courant

continu de 12 ou 24 Volts (A). À l’heure actuelle, la plupart

des voitures et des camions fonctionnent avec une mise à

la masse négative. On peut s’en assurer en vériﬁant que la

borne (-) de la batterie soit bien connectée au bloc mo-

teur ou au châssis. Dans le cas contraire, consultez votre

revendeur.

a) Assurez-vous que l’alimentation soit bien de 12 ou 24 Volts.

b) Repérez les bornes (+) et (-) de la batterie (+ = rouge, - =

noir). Dans le cas où il serait nécessaire de rallonger le cordon

d’alimentation, utilisez un câble de section équivalente ou

supérieure.

LOBE DE RAYONNEMENT

Français

20

c) Il est nécessaire de se connecter sur un (+) et un (-) perma-

nents. Nous vous conseillons donc de brancher directement

le cordon d’alimentation sur la batterie (le branchement sur

le cordon de l’autoradio ou sur d’autres parties du circuit

électrique pouvant dans certains cas favoriser la réception

de signaux parasites).

d) Branchez le ﬁl rouge (+) à la borne positive de la batterie

et le ﬁl noir (-) à la borne négative de la batterie.

e) Branchez le cordon d’alimentation au poste.

ATTENTION : Ne jamais remplacer le fusible d’origine (2 A)

par un modèle d’une valeur différente !

4) OPÉRATIONS DE BASE À EFFECTUER AVANT LA PREMIÈRE

UTILISATION, SANS PASSER EN ÉMISSION (sans appuyer

sur la pédale du micro)

a) Branchez le micro,

b) Vériﬁez le branchement de l’antenne,

c) Mise en marche de l’appareil : tournez le bouton de volume

VOL (1) dans le sens des aiguilles d’une montre jusqu’à

entendre un “clic”.

d) Tournez le bouton du squelch SQ (2) au minimum (position

M).

e) Réglez le bouton VOLUME à un niveau convenable.

f) Amenez le poste sur le canal 20 à l’aide des touches s/t

(4/5) ou UP/DN (14/15) du microphone.

5) RÉGLAGE DU TOS (Taux d’ondes stationnaires)

ATTENTION : Opération à effectuer impérativement lors de

la première utilisation de l’appareil ou lors d’un change-

ment d’antenne. Ce réglage doit être fait dans un endroit

dégagé, à l’air libre.

Réglage avec TOS-mètre externe (type TOS-1 PRESIDENT)

a) Branchement du Tos-mètre :

- Brancher le Tos-mètre entre le poste et l’antenne, le plus

près possible du poste (utilisez pour cela un câble de 15,75

pouces (40 cm) maximum type CA-2C PRESIDENT).

b) Réglage du Tos :

- Amener le poste sur le canal 20,

- Positionner le commutateur du Tos-mètre en position FWD

(calibrage),

- Appuyer sur la pédale du micro pour passer en émission,

- Amener l’aiguille sur l’index t à l’aide du bouton de ca-

librage,

- Basculer le commutateur en position REF (lecture de la

valeur du TOS). La valeur lue sur le vu-mètre doit être très

proche de 1. Dans le cas contraire, rajuster votre antenne

jusqu’à obtention d’une valeur aussi proche que possible

de 1 (une valeur de TOS comprise entre 1 et 1,8 est ac-

ceptable),

- Il est nécessaire de recalibrer le Tos-mètre, entre chaque

opération de réglage de l’antenne.

Remarque : Aﬁn d’éviter les pertes et atténuations dans

les câbles de connexion entre la radio et ses accessoires,

PRESIDENT recommande une longueur de câble inférieure

à 118,11 pouces (3 m).

Réglage avec le TOS-mètre intégré

Appuyer brièvement sur la touche •F/MEM (6) puis sur

la touche s (4) ou UP (14) pour activer (/désactiver) la

fonction SWR (voir § •SWR page 21). La valeur du TOS

est indiqué dans l’afﬁcheur. Quand le réglage est terminé,

désactiver la fonction SWR.

Maintenant, votre poste est prêt à fonctionner.

Français

La page charge ...

PRESIDENT JOHNSON II Le manuel du propriétaire

PRESIDENT JOHNSON II Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents