red lion DA PID Module Manuel utilisateur

Marque: red lion

Modèle: DA PID Module

Taper: Manuel utilisateur

Installation DAPID-A

Drawing No. LP1120

Effective 03/2020

DA PID Single Loop and Dual Loop Modules

Installation Guide

MODULE PACKAGE CHECKLIST

This product package should contain the items listed below. If

any items are missing or damaged, contact Red Lion immediately.

- DIN rail mount DA PID Module

- Installation Guide

GENERAL DESCRIPTION

The DA PID modules are full featured PID controllers designed

for use with the DA70 controllers. The 1PID is a single loop

controller, while the 2PID is a dual loop controller. The design of

the system provides a true modular PID control platform for

multi-zone control applications. The modules can accept a wide

range of thermocouple, RTD, 0-10 V, 0/4-20 mA signals. With

multiple discrete outputs, plus an analog output (1PID only), the

DA PID modules can perform virtually any combination of time-

proportioning or linear control for heat, cool, or heat/cool

applications. The discrete outputs may also be assigned to one of

seven internal soft alarms. The 1PID’s linear output can be

assigned to transmit virtually any internal variable.

The modules connect and communicate via proprietary

backplane to the DA host device. The DA host device, equipped

with serial ports as well as an Ethernet port(s), allows the system

to share data with PCs, PLCs, and SCADA systems.

Internal power management circuits allow the module to be

replaced while power is applied, which reduces downtime in the

event of a relay failure. All configuration information is stored

locally within the module, as well as in the Host, so replacement

modules do not need to be configured.

The modules can operate in On/Off, P, PI, or PID control mode,

and use an on-demand Auto-Tune that establishes the tuning

constants. The PID constants may be fine-tuned through the

serial or Ethernet interface. The modules employ a unique

overshoot suppression feature, which allows the quickest

response without excessive overshoot. The modules can also be

operated in manual mode, providing the operator with direct

control of the output.

CONFIGURATION

The DA PID modules are configured with Windows

compatible

Crimson

software. The software is an easy to use, graphical

interface which provides a means of configuration and

commissioning of new systems, as well as routine re-calibration

of modules.

ALARMS

Each loop within the modules has seven internal “soft” alarms,

which can be assigned to trigger any output. This includes four

process alarms, two heater current, and one input fault alarm.

ANALOG OUTPUT OPTION (1PID ONLY)

The DC Analog Output (10 V or 20 mA) can be independently

configured and scaled for control or re-transmission purposes.

HEATER CURRENT MONITOR OPTION (2PID ONLY)

The optional Heater Current Monitor input is useful for early

warning of heater degradation, or heater circuit failure. The input

0.49

(12.51)

0.45

(11.50)

4.53 (114.97)

6.22

(157.91)

1.91

(48.51)

1.35

(34.32)

6.00

(152.40)

This

terminal

2PID only

DIMENSIONS In inches (mm)

z Dedicated single and dual PID modules for the DA70

z Auto addressing minimizes configuration time

z Fully isolated design provides reliable operation

z PID control with reduced overshoot

z Universal inputs accept TC, RTD, 0-10 V and 0/4-20 mA

signals

z On demand auto-tuning of PID settings

z DC analog output (1PID only)

z Heater current input (optional, 2PID only) ensures detection

of heater circuit failure

z Configured using Crimson

software (version 3.1 or later)

LISTED

IND.CONT. EQ.

E317425

FOR USE IN HAZARDOUS LOCATIONS:

Class I, Division 2, Groups A, B, C, and D

For Part Numbers: DAM00PDP1SA00000,

DAM00PDP2S000000, and DAM00PDP2SM00000 Only

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx UL 20.0007X

Drawing No. LP1120 Effective 03 2020

connects to a current transformer with an output of 100 mA AC

to ensure that proper heater current is present when the control

output is on, and that little or no current is present when the

output is off. This provides immediate warning of a circuit short

or open, instead of waiting for a high or low temperature

shutdown alarm.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that

appear in this document or on equipment must be observed to

ensure personal safety and to prevent damage to either the

device or equipment connected to it.

Do not use these products to replace proper safety interlocking.

No software-based device (or any other solid-state device) should

ever be designed to be responsible for the maintenance of

personnel safety or consequential equipment not equipped with

safeguards. Red Lion disclaims any responsibility for damages,

either direct or consequential, that result from the use of this

equipment in a manner not specified.

SPECIFICATIONS

1. POWER: Power is supplied by the DA host device. Modules

may be hot-swapped (replaced while powered up) in non-

hazardous locations only.

1PID Max Power: 3.3 W

2PID Max Power: 2.7 W

2. LEDs

STS – RGB Status LED shows module condition.

OP1, OP2, OP3, OP4 - Indicate status of outputs 1, 2, 3, and 4

ALM, or ALM1 and ALM2 - Alarm LEDs are lit during an

internal alarm condition

Default configuration.

3. MEMORY: Non-volatile memory retains all programmable

parameters.

4. INPUTS:

GENERAL:

Sample Time: 50 msec (20 Hz)

Common Mode Rejection: >110 dB, 50/60 Hz

Normal Mode Rejection: >50 dB, 50/60 Hz

Temperature Coefficient: 0.01%/

Step Response Time: 100 msec typ., 200 msec max

THERMOCOUPLE INPUTS:

Types: T, E, J, K, R, S, B, N, C

Input Impedance: 20 M ohm

Lead Resistance Effect: 0.25 µV/ohm

Cold Junction Compensation: Less than ±1 °C typical (±1.5

°C max) over -40 to 75 °C ambient temperature

Resolution: 0.1

TYPE

MEASUREMENT

RANGE

WIRE COLOR

ANSI BS 1843

-200 to +400 °C

-328 to +752 °F

(+) Blue

(-) Red

(+) White

(-) Blue

-200 to +730 °C

-328 to +1346 °F

(+) Violet

(-) Red

(+) Brown

(-) Blue

-200 to +760 °C

-328 to +1400 °F

(+) White

(-) Red

(+) Yellow

(-) Blue

-200 to +1350 °C

-328 to +2462 °F

(+) Yellow

(-) Red

(+) Brown

(-) Blue

0 to +1768 °C

+32 to +3214 °F

No Standard

(+) White

(-) Blue

0 to +1768 °C

+32 to +3214 °F

No Standard

(+) White

(-) Blue

+149 to +1820 °C

+300 to +3308 °F

No Standard No Standard

-200 to +1300 °C

-328 to +2372 °F

(+) Orange

(-) Red

(+) Orange

(-) Blue

C W5/W6

0 to +2315 °C

+32 to +4199 °F

No Standard No Standard

mV 0 mV to 50 mV N/A N/A

RTD INPUTS:

Type: 2 or 3 wire

Excitation: 150 µA

Lead Resistance: 15 ohms Max

Resolution: 1 or 0.1°

TYPE INPUT TYPE RANGE

385 100 ohm platinum, Alpha = .00385

-200 to +600°C

-328 to +1100°F

392 100 ohm platinum, Alpha = .003919

-200 to +600°C

-328 to +1100°F

672 120 ohm nickel, Alpha = .00672

-80 to +215°C

-112 to +419°F

PROCESS INPUT:

INPUT

RANGE

ACCURACY IMPEDANCE

MAX

CONTINUOUS

OVERLOAD

RESOLUTION

10 V 0.1% span 1 M Ohm 50 V 16 bit

20 mA 0.1% span 10 Ohm 100 mA 16 bit

5. PROBE BREAK RESPONSE: Upscale drive, Input Fault Alarm

bit set high, ALx LED illuminates.

6. TEMPERATURE INDICATION ACCURACY: ± (0.3% of span,

+1 °C). Includes NIST conformity, cold junction effect, A/D

conversion errors, temperature coefficient and linearization

conformity at 23 °C after 20 minute warm up.

7. ISOLATION LEVEL: 500 Vrms @ 50/60 Hz for 1 minute

between the following:

OP1

OP2

OP3

OP4

Linear Output (1PID only)

Signal Input 1 and HCM (2PID only)

Signal Input 2 and HCM (2PID only)

Power Supply Input

CAUTION: Risk of Danger

Read complete instructions prior to installation and

operation of the unit.

ATTENTION : Risque de danger

Lire les instructions complètes avant l’installation et

l’utilisation de l’appareil.

WARNING - EXPLOSION HAZARD - SUBSTITUTION

OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIVISION 2

AVERTISSEMENT - DANGER D’EXPLOSION - LE

REMPLACEMENT DE COMPOSANTS PEUT NUIRE À

L’APTITUDE À LA CLASSE I, DIVISION 2

This equipment is suitable for use in Class I, Division 2,

Groups A, B, C, D, or non-hazardous locations only.

Cet équipement est adapté à une utilisation dans des

endroits de classe I, Division 2, Groupes A, B, C, D, ou

dans des endroits non dangereux seulement.

WARNING - EXPLOSION HAZARD. NOT HOT

SWAPPABLE. DO NOT REMOVE OR REPLACE WHILE

CIRCUIT IS LIVE UNLESS THE AREA IS FREE OF

IGNITIBLE CONCENTRATIONS.

AVERTISSEMENT - RISQUE D’EXPLOSION. NON

ÉCHANGEABLE À CHAUD. NE PAS RETIRER OU

REMPLACER SOUS TENSION SAUF SI LA ZONE EST

EXEMPTE DE CONCENTRATIONS INFLAMMABLES.

Effective 03 2020 Drawing No. LP1120

8. COMMUNICATIONS: Provided by the DA host device

9. A/D CONVERTER: 16 bit resolution

10. DISCRETE OUTPUTS:

1PID: Outputs 1 and 2 available as Solid State NFET or Form

A relay. Output 3 is Solid State NFET or Form C relay.

2PID: Outputs 1, 2 and 4 available as Solid State NFET or

Form A relay. Output 3 is Solid State NFET or Form C relay.

Solid State Output:

Type: Switched DC, N Channel open drain MOSFET

Current Rating: 1 A max

VDS ON: 0.3 V @ 1 A

VDS MAX: 30 VDC

Offstate Leakage Current: 0.5 mA max

Format A Relay Output:

Type: N.O.

Current Rating: 3 Amps @ 125 VAC or 30 VDC (resistive

load); 1/10 HP @ 125 VAC

Life Expectancy: 200,000 cycles at maximum load rating.

(Decreasing load, increasing cycle time, and use of surge

suppression such as RC snubbers increases life expectancy.)

Form C Relay Output:

Type: SPDT

Current Rating: 3 Amps @ 125 VAC or 28 VDC (resistive

load); 1/10 HP @ 125 VAC

Life Expectancy: 100,000 cycles at maximum load rating.

(Decreasing load, increasing cycle time, and use of surge

suppression such as RC snubbers increases life expectancy.)

11. CONTROL MODES:

Control: On/Off, P, PI, or PID

Output: Time proportioning or linear (1PID only)

Cycle Time: Programmable from 0.0 to 60.0 sec

Auto-Tune: When selected, sets proportional band, integral

time, derivative time values, and output dampening time

Probe Break Action: Programmable response

Sensor Fail Response: Upscale

12. ALARMS:

Modes:

Manual

Absolute High Acting

Absolute Low Acting

Deviation High Acting

Deviation Low Acting

Inside Band Acting

Outside Band Acting

Reset Action: Programmable; automatic or latched

Standby Mode: Programmable; enable or disable

Hysteresis: Programmable

Sensor Fail Response: Upscale

13. ANALOG DC OUTPUT (1PID only):

Selectable/programmable for 0-10 VDC, 0-20 mA, or 4-20 mA

Resolution:

Voltage: 500 µV

Current: 1 µA

Accuracy:

0.1% of full scale (18 to 28 °C)

0.2% of full scale (-40 to 75 °C)

Update Time: 0.0 to 60.0 sec

Compliance (for current output only): 500 ohm max.

Minimum load (voltage output only): 10 K ohm min.

Outputs are software selectable for either 10 V or 20 mA. The

output range may be field calibrated to yield approximate

10% overrange and a small underrange (negative) signal.

14. HEATER CURRENT MONITOR INPUT (optional):

Type: 300 V max, 50 A max. Single phase, full wave

monitoring of load currents

Input: 100 mA max. input for use with external current

transformers

Input Resistance: 5 ohms

Accuracy: ±3.0% full scale, 5 to 100% of range

Frequency: 50 to 400 Hz

Minimum output on time for break alarm: 350 msec

Note: To ensure isolation to SELV circuits, use a UL Listed current

transformer.

15. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range:

Modules with Relays: -40 to 70 °C

Modules with Solid-State Outputs: -40 to 75 °C

Storage Temperature Range: -40 to +85 °C

Shock to IEC 68-2-27: Operational 40 g (15 g, modules w/

relays)

Operating and Storage Humidity: 0 to 85% max. Relative

humidity, non-condensing.

Altitude: Up to 2000 meters

16. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

IEC/EN 61010-1

RoHS Compliant

ATEX Approved (DAM00PDP1SA00000, DAM00PDP2S000000,

and DAM00PDP2SM00000 Only)

II 3 G Ex ec IIC T4 Gc

DEMKO 20 ATEX 2268X

IECEx Approved (DAM00PDP1SA00000, DAM00PDP2S000000,

and DAM00PDP2SM00000 Only)

IECEx UL 20.0007X

UL Hazardous: File #E317425

Rugged IP30 enclosure

17. CONSTRUCTION: Metal and plastic enclosure with IP30

rating. For use only in approved enclosure.

18. CONNECTIONS: Removable wire clamp screw terminal

blocks

Wire Strip Length: 0.3” (7.5 mm)

Wire Gauge Capacity: 14 to 24 AWG (2.08 to 0.20 mm

)

copper wire only

Torque: 2 inch-lbs (0.23 N-m)

19. MOUNTING: Mounts onto standard DIN style top hat (T)

profile mounting rails according to EN50022 – 35 x 7.5 mm

and 35 x 15 mm.

20. WEIGHT: 11.1 oz (315 g)

Drawing No. LP1120 Effective 03 2020

EMC INSTALLATION GUIDELINES

Although Red Lion Controls products are designed with a high

degree of immunity to Electromagnetic Interference (EMI), proper

installation and wiring methods must be followed to ensure

compatibility in each application. The type of the electrical noise,

source or coupling method into a unit may be different for various

installations. Cable length, routing, and shield termination are

very important and can mean the difference between a successful

or troublesome installation. Listed are some EMI guidelines for a

successful installation in an industrial environment.

1. A unit should be mounted in a metal enclosure, which is

properly connected to protective earth.

2. Use shielded cables for all Signal and Control inputs. The

shield connection should be made as short as possible. The

connection point for the shield depends somewhat upon the

application. Listed below are the recommended methods of

connecting the shield, in order of their effectiveness.

a. Connect the shield to earth ground (protective earth) at one

end where the unit is mounted.

b. Connect the shield to earth ground at both ends of the

cable, usually when the noise source frequency is over 1

MHz.

3. Never run Signal or Control cables in the same conduit or

raceway with AC power lines, conductors, feeding motors,

solenoids, SCR controls, and heaters, etc. The cables should

be run through metal conduit that is properly grounded. This

is especially useful in applications where cable runs are long

and portable two-way radios are used in close proximity or if

the installation is near a commercial radio transmitter. Also,

Signal or Control cables within an enclosure should be routed

as far away as possible from contactors, control relays,

transformers, and other noisy components.

4. Long cable runs are more susceptible to EMI pickup than

short cable runs.

5. In extremely high EMI environments, the use of external EMI

suppression devices such as Ferrite Suppression Cores for

signal and control cables is effective. The following EMI

suppression devices (or equivalent) are recommended:

Fair-Rite part number 0443167251 (Red Lion Controls

#FCOR0000)

Line Filters for input power cables:

Schaffner # FN2010-1/07 (Red Lion Controls #LFIL0000)

6. To protect relay contacts that control inductive loads and to

minimize radiated and conducted noise (EMI), some type of

contact protection network is normally installed across the

load, the contacts or both. The most effective location is

across the load.

a. Using a snubber, which is a resistor-capacitor (RC) network

or metal oxide varistor (MOV) across an AC inductive load is

very effective at reducing EMI and increasing relay contact

life.

b. If a DC inductive load (such as a DC relay coil) is controlled

by a transistor switch, care must be taken not to exceed the

breakdown voltage of the transistor when the load is

switched. One of the most effective ways is to place a

diode across the inductive load. Most Red Lion products

with solid state outputs have internal zener diode

protection. However external diode protection at the load is

always a good design practice to limit EMI. Although the

use of a snubber or varistor could be used.

Red Lion part numbers: Snubber: SNUB0000

Varistor: ILS11500 or ILS23000

7. Care should be taken when connecting input and output

devices to the instrument. When a separate input and output

common is provided, they should not be mixed. Therefore a

sensor common should NOT be connected to an output

common. This would cause EMI on the sensitive input

common, which could affect the instrument’s operation.

Visit https://www.redlion.net/emi for more information on EMI

guidelines, Safety and CE issues as they relate to Red Lion

products.

Block Diagram

POWER

SUPPLY

VDC

1PID - SINGLE LOOP PID MODULE

HCM

0-20mA

0-10V

RTD

ISOLATED

POWER

SUPPLY

SSR

OUTPUTS

OP1-SSR1

OP2-SSR2

OP3-SSR3

ISOLATED

LINEAR

OUTPUT

ISOLATED

0-10V

0-20mA

INPUTS

ISOLATED

RELAY

OUTPUTS

OP1-RELAY

OP2-RELAY

OP3-RELAY

POWER

SUPPLY

ISOLATED

SSR

OUTPUTS

2PID - DUAL LOOP PID MODULE

OP4-SSR4

ISOLATED

0-20mA

HCM

0-10V

RTD

OP1-RELAY

OUTPUTS

INPUT 1

RELAY

ISOLATED

OP2-RELAY

OP3-RELAY

OP4-RELAY

ISOLATED

0-20mA

HCM

0-10V

RTD

INPUT 2

OP3-SSR3

OP2-SSR2

OP1-SSR1

DA SERIES HOST

Effective 03 2020 Drawing No. LP1120

HARDWARE INSTALLATION

Removing Module From Cradle

To remove the module from the cradle, push in the module

release button at the top of the cradle and pull the module out of

the cradle.

Attaching the Module/Cradle to the DIN Rail

The DIN rail should be

mounted horizontally so that the

unit’s ventilation holes are

vertical in relation to installation

orientation. A minimum clearance

of 1 inch (25.4 mm) should be

maintained above and below the

unit to ensure proper thermal

regulation.

The cradle can be installed on

the DIN rail with or without the

module attached. Ensure the DIN

rail lock latch is in the outward

most position (unlocked). Hook

the top back of the cradle DIN

rail clip over the DIN rail. Press

the cradle until flush with the rail and push the DIN rail lock latch

to the latched (in) position.

For hazardous location installation, the following shall be taken

into consideration:

— The equipment shall only be used in an area of at least

pollution degree 2, as defined in EN/IEC 60664-1.

— The equipment shall be installed in an enclosure that provides

a minimum ingress protection of IP54 in accordance with EN/

IEC 60079-0. The enclosure shall be accessible only with the

use of a tool.

— Transient protection shall be provided that is set at a level

not exceeding 140% of the peak rated voltage value at the

supply terminals to the equipment.

Installing Module into Cradle

Push module into cradle until you hear an audible click

indicating it is properly latched.

WIRING

WIRING CONNECTIONS

All power, input and output (I/O) wiring must be in accordance

with Class I, Division 2 wiring methods and in accordance with

the authority having jurisdiction.

All conductors should meet voltage and current ratings for each

terminal. When wiring the module, use the numbers on the label

to identify the position number with the proper function. Strip

the wire, leaving approximately 0.3" (7.5 mm) of bare wire

exposed. Insert the wire into the terminal, and tighten.

MODULE

CRADLE

DIN RAIL LOCK LATCH

Unlock Lock

MODULE CRADLE

DIN

rail

ANALOG+

ANALOG-

N/C

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

N/C

OP1 COM

OP3 N.O. / +

OP2 COM

OP2 +

OP3 N.C.

OP3 COM

OP1 +

OUTPUT

1PID MODULE

Terminals 17 to 24

(2PID Only)

Terminals 9 to 16

Terminals 1 to 8

INPUT 1

HCM1 (OPT.)

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

HCM1 (OPT.)

OP1 COM

OP4 +

OP4 COM

OP3 N.O. / +

OP2 COM

OP2 +

OP3 N.C.

OP3 COM

OP1 +

HCM2 (OPT.)

0-10V

4-20mA

INPUT COM

TC/RTD+

RTD +EXC

HCM2 (OPT.)

N/C

OUTPUT

2PID MODULE

INPUT 1

INPUT 2

CAUTION: Only UL listed wiring with temperature

ratings greater than 90 °C permitted for Class I, Division

2, Zone 2 and ATEX/IECex installations.

ATTENTION: Seul le câblage homologué UL avec des

températures nominales supérieures à 90°C est autorisé

pour les installations de classe I, Division 2 , zone 2 et

ATEX/IECex.

Drawing No. LP1120 Effective 03 2020

INPUT WIRING

RTD +EXC

TC/RTD+

0-10 V

HCM (OPT)

4-20 mA

INPUT COM

Thermocouple and Millivolt

RTD +EXC

TC/RTD+

0-10 V

HCM (OPT)

4-20 mA

INPUT COM

RTD

RTD +EXC

TC/RTD+

0-10 V

HCM (OPT)

4-20 mA

INPUT COM

VDC-

VDC+

Voltage

RTD +EXC

TC/RTD+

0-10 V

HCM (OPT)

4-20 mA

INPUT COM

LOAD

POWER

Current

Heater Circuit

RTD +EXC

TC/RTD+

0-10 V

HCM (OPT)

4-20 mA

INPUT COM

Heater Current Monitor

OUTPUT WIRING

Load

Power

OPx +

OPx COM

Relay Outputs

Load

Power

OPx +

OPx COM

Solid State Outputs

Recorder,

Controller,

Valve, etc

ANALOG+

ANALOG-

Analog Output (1PID Only)

LEDs

STATUS LED

The red/green/blue Status LED is located at the top of the

module and provides information regarding the state of the

module. This includes indication of the various stages of the start-

up routine (power-up), as well as any errors that may occur.

LED COLOR(S) MEANING

Flashing Blue Module is booting.

Flashing Green Module is switching to configuration.

Green Module is performing normally.

Flashing Green/Purple Module is performing auto calibration.

Flashing Blue/Yellow Module is being flash upgraded by Crimson.

Flashing Red Error: general error with module.

Flashing Red/Green

Error: module is controlling properly, but has lost

communication with the Host.

Flashing Yellow Error: no bus frequency.

Flashing Red/Green/Blue

Error: module is running the Factory Programming

Console.

OP1, OP2, OP3, OP4

– Output Status LED

The green OP1, OP2, OP3, and OP4* LEDs are factory

configured to indicate the status of the outputs. The LEDs turn on

when the output is active.

These LEDs may be remapped to various other module

properties.

*2PID only

ALM or ALM1, ALM2 – Alarm LED

The red Alarm LEDs indicate the presence of an alarm.

Whenever one of the seven alarms is active, the LED turns on.

FIRMWARE UPGRADE

The module’s firmware is stored in flash memory so that

software/ hardware conflicts are avoided, and so features can be

added in the future.

During a download, Crimson compares its own library of

firmware files with those stored in the module. If they do not

match, Crimson will download the necessary firmware.

Effective 03 2020 Drawing No. LP1120

RED LION CONTROLS TECHNICAL SUPPORT

If for any reason you have trouble operating, connecting, or

simply have questions concerning your new DA Module, contact

Red Lion’s technical support.

Support: support.redlion.net

Website: www.redlion.net

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

Red Lion Controls, Inc.

20 Willow Springs Circle York, PA 17406

ORDERING INFORMATION

TYPE DESCRIPTION PART NUMBER

Input

Modules

DA70 Series Module, Single PID, Relay and Analog Outputs

DA M00PD P1RA0 0000

DA70 Series Module, Single PID, SSR and Analog Outputs DA M00PD P1SA0 0000

DA70 Series Module, Dual PID, Relay Outputs

DA M00PD P2R00 0000

DA70 Series Module, Dual PID, SSR Outputs DA M00PD P2S00 0000

DA70 Series Module, Dual PID, SSR and Heater Current Monitor DA M00PD P2SM0 0000

Accessories

50 Amp Current Transformer (For Heater Current Models),

UL Recognized component, Instrument Transformers,

Inc. Part #2SFT500-0.

CT005001

A listing of the entire DA70 family of products and accessories can be found at www.redlion.net.

Module is not suitable for use in hazardous locations.

LIMITED WARRANTY

(a) Red Lion Controls Inc. (the “Company”) warrants that all Products shall be free from defects in material and

workmanship under normal use for the period of me provided in “Statement of Warranty Periods” (available at

www.redlion.net) current at the me of shipment of the Products (the “Warranty Period”). EXCEPT FOR THE

ABOVE-STATED WARRANTY, COMPANY MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE

PRODUCTS, INCLUDING ANY (A) WARRANTY OF MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY

RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE

OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. Customer shall be responsible for determining that a

Product is suitable for Customer’s use and that such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a

result of Customer’s failure to store, install, commission or maintain the Product according to specicaons; (ii)

Customer alters or repairs such Product without the prior wrien consent of Company.

sole discreon, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that,

if Company so requests, Customer shall, at Company’s expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY AND COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET

FORTH IN PARAGRAPH (a).

company and product names are trademarks of their respective owners.

red lion DA PID Module Manuel utilisateur

Marque: red lion

Modèle: DA PID Module

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: red lion DA PID Module User manual

red lion DA PID Module Manuel utilisateur

red lion DA PID Module Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents