JVC EXAD KD-LHX601 Manuel utilisateur

Catégorie
Récepteurs multimédia de voiture
Taper
Manuel utilisateur

Ce manuel convient également à

LVT1119-001A
[E/EX]
KD-LHX601
CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
ENGLISH
DEUTSCH
NEDERLANDS
FRANÇAIS
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende
handleiding.
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL DINSTRUCTIONS
GEBRUIKSAANWIJZING
This unit is equipped with the display demonstration. To cancel it, see page 8.
Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf Seite 8 wird
beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.
Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-
vous à la page 8.
Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 8 voor het annuleren van deze
functie.
Cover_001A_KD-LHX601[E_EX].p65 04.1.15, 2:27 PM3
2
ENGLISH
How to reset your unit
Press the reset button on the control panel using a ball-
point pen or a similar tool.
This will reset the built-in
microcomputer.
Note:
Your preset adjustments—such
as preset channels or sound
adjustments—will also be
erased.
Caution:
If the temperature inside the car is below 0˚ C, the movement of animation and text scroll will be halted on
the display to prevent the display from being blurred. (LOW TEMP.) indicator appears on the display.
When the temperature increases, the operating temperature is resumed, and these functions will start
working again.
CAUTION on Volume Setting:
Discs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for
example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the
volume before playing a disc and adjust it as required during playback.
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
CAUTION:
NEVER insert your finger in
between the control panel and
the unit, as it may
get caught or
hurt.
(See page 61.)
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
EN02-03_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM2
3
ENGLISH
CONTENTS
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
How to reset your unit ............................... 2
LOCATION OF THE BUTTONS ............ 4
Control panel ............................................. 4
Illumination Navigation for easy operations ...
4
Remote controller ...................................... 5
Preparing the remote controller ................ 6
BASIC OPERATIONS ....................... 7
Turning on the power ................................ 7
Canceling the display demonstration ........ 8
Setting the clock ........................................ 9
RADIO OPERATIONS ...................... 10
Listening to the radio ................................. 10
Storing stations in memory ....................... 12
Tuning in to a preset station ...................... 14
Changing the display pattern .................... 15
RDS OPERATIONS ......................... 16
What you can do with RDS ....................... 16
Other convenient RDS functions and
adjustments ............................................ 21
DAB TUNER OPERATIONS ................ 23
Tuning in to an ensemble and one of the
services .................................................. 23
Storing DAB services in memory .............. 25
Tuning in to a preset DAB service ............. 25
What you can do more with DAB .............. 27
Changing the display pattern .................... 30
DISC OPERATIONS ........................ 31
About MP3 and WMA discs ...................... 31
Playing a disc ............................................ 31
Locating a track or a particular portion
on a disc ................................................. 34
Selecting a folder and a track using the
name lists ............................................... 36
Selecting the playback modes .................. 37
Prohibiting disc ejection ............................ 38
Changing the display pattern .................... 39
SOUND ADJUSTMENTS ................... 40
Adjusting the sound .................................. 40
Selecting preset sound modes
(iEQ: intelligent equalizer) ...................... 41
Storing your own sound modes ................ 43
Selecting the display theme ...................... 44
GRAPHIC DISPLAYS ........................ 45
Downloading images and animations ....... 46
Deleting unwanted files ............................. 48
Activating the downloaded images and
animations .............................................. 50
OTHER MAIN FUNCTIONS ................ 52
Changing the general settings (PSM) ....... 52
Selecting the dimmer mode ...................... 57
Changing the display color ........................ 58
Assigning names to the sources ................ 60
Changing the control panel angle .............. 61
Detaching the control panel ...................... 61
CD CHANGER OPERATIONS .............. 62
Playing discs ............................................. 62
Selecting a disc/folder/track using the
name lists ............................................... 65
Selecting the playback modes .................. 66
EXTERNAL COMPONENT OPERATIONS ... 68
Playing an external component ................. 68
Changing the display pattern .................... 68
TROUBLESHOOTING ...................... 69
MAINTENANCE ............................. 72
Handling discs ........................................... 72
SPECIFICATIONS ........................... 73
*Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
BEFORE USE
*For safety....
Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
Stop the car before performing any complicated
operations.
EN02-03_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM3
ENGLISH
4
LOCATION OF THE BUTTONS
Control panel
Illumination Navigation for easy operations
If you use M (MODE) or SEL (select), the display and some controls (such as the number buttons,
4 /¢ , 5/, and control dial) enter the corresponding control mode, then the controls
start flashing to lead you to the next operational steps. (Illumination Navigation)
The display shows how these buttons function during this period.
Ex.: When you press number button 1 after pressing M (MODE), to operate the FM tuner.
To use these controls for original functions again, wait until the controls stop flashing without
using these controls.
Pressing M (MODE) again also restores original functions. However, pressing SEL (select)
makes the unit into a different mode.
Time countdown indicator
1 (standby/on/attenuator) button
2 TP/PTY (traffic programme/programme type)
button
3 Control dial
4 Display window
5 FM/AM DAB button
6 5 (up) button
7 0 (eject) button
(angle) button
8 4 /¢ buttons
9 SEL (select) button
p D (DISP: display) button
q Number buttons
w M (MODE) button
e Remote sensor
r (down) button
t CD/CD-CH (CD changer) LINE button
y (control panel release) button
EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM4
ENGLISH
5
Remote controller
3 Selects the preset stations or service while
listening to the radio or the DAB tuner.
Each time you press the button, the preset
station or service number increases, and the
selected station or service is tuned in.
Skips to the first track of the previous folder
while listening to an MP3 disc or a WMA
disc.
Each time you press the button, you can
move to the previous folder and start playing
the first track.
While playing an MP3 disc on an MP3-
compatible CD changer;
Skips to the previous disc if pressed
briefly.
Skips to the previous folder if pressed and
held.
Note:
While playing a CD on a CD changer, this
always skips to the previous disc.
4 Selects the sound mode (iEQ: intelligent
equalizer).
Each time you press the button, the sound
mode (iEQ) changes.
5 Selects the band while listening to the radio
or the DAB tuner.
Each time you press the button, the band
changes.
Skips to the first track of the next folder while
listening to an MP3 disc or a WMA disc.
Each time you press the button, you can
move to the next folder and start playing the
first track.
While playing an MP3 disc on an MP3-
compatible CD changer;
Skips to the next disc if pressed briefly.
Skips to the next folder if pressed and
held.
Note:
While playing a CD on a CD changer, this
always skips to the next disc.
6 Selects the source.
Each time you press the button, the source
changes.
7 Functions the same as the control dial on the
main unit.
Note:
These buttons do not function for the
preferred setting mode (PSM) adjustment.
1 Turns on the unit if pressed when the unit is
turned off.
Turns off the unit if pressed and held for a
few seconds.
Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.
2 Searches for stations while listening to the
radio.
Selects services while listening to the DAB
tuner if pressed briefly.
Searches for ensembles while listening to
the DAB tuner if pressed for more than one
second.
Fast-forwards or reverses the track if
pressed and held while listening to a disc.
Skips to the beginning of the next track or
goes back to the beginning of the current (or
previous) tracks if pressed briefly while
listening to a disc.
EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM5
ENGLISH
6
Preparing the remote controller
Before using the remote controller:
Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of
the remote controller decreases, replace the
battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.
2) Remove the battery holder.
2. Place the battery.
Slide the battery into the holder with the +
side facing upwards so that the battery is
fixed in the holder.
Lithium coin
battery (product
number: CR2025)
(back side)
Remote sensor
(back side)
3. Return the battery holder.
Insert again the battery holder by pushing it
until you hear a clicking sound.
WARNING:
Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.
Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack, or start a fire.
When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start
a fire.
Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.
CAUTION:
DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight for
a long time. Otherwise, it may be damaged.
KD-LHX601 is equipped with the steering
wheel remote control function.
If your car is equipped with the steering wheel
remote controller, you can operate this
receiver using the controller.
See the Installation/Connection Manual
(separate volume) for connection to utilize
this function.
EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM6
7
ENGLISH
3
Adjust the volume.
4
Adjust the sound as you want.
(See pages 40 – 43.)
Note:
While playing a source, you can select the display
theme of your preference. For details, see “Selecting
the display theme” on page 44.
NOTICE:
The illustrations of the display used in this manual
are mainly of the initial setting when shipped from
the factory. If you have changed the display
patterns or some PSM items, the actual displays
you see will be different.
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
When you select a source in step
2
below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2
Select the source.
To operate the FM/AM tuner or the DAB
tuner, press and hold FM/AM DAB
repeatedly.
To operate the CD player (CD),
CD changer (CD-CH), or external
component (LINE-IN), press
CD/CD-CH LINE repeatedly.
*
1
If there is no disc in the loading slot, you
cannot select “CD” as the source, “No
Disc” flashes on the display.
*
2
Without connecting the CD changer, you
cannot select “CD-CH” as the source to
play.
BASIC OPERATIONS
To increase the volume
To decrease the volume
Volume level appears.
Current sound mode (iEQ)
(see page 41)
1
2
3
EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM7
8
ENGLISH
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
If you turn the control dial, you can also restore
the sound.
To turn off the power
Press and hold for more than one
second.
If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.
Canceling the display
demonstration
When shipped from the factory, display
demonstration has been activated, and starts
automatically when no operations are done for
about 20 seconds.
It is recommended to cancel the demonstration
before you use the unit for the first time.
To cancel the display demonstration, follow
the procedure below:
1
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 53 and 54.)
The next-step-operation
buttons start flashing.
2
Press number button 1 to select
“MOVIE”—Movie category of the
PSM settings.
The “Graphics” setting screen appears on
the display.
3
Select “Off.
4
Finish the setting.
To activate the display demonstration, repeat
the same procedure and select “Int Demo” or “All
Demo” in step
3
.
For more details, see “To show the graphics on
the display—Graphics” on page 55.
EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM8
9
ENGLISH
Setting the clock
You can also set the clock system to either
24 hours or 12 hours.
1
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 53 and 54.)
The next-step-operation
buttons start flashing.
2
Press number button 2 to select
“CLOCK”—Clock category of the
PSM settings.
The “Clock Hr” (hour) setting screen
appears on the display.
3
Adjust the hour.
4
Set the minute.
1 Select “Clock Min” (minute).
2 Adjust the minute.
12
5
Set the clock system.
1 Select “24H/12H.
2 Select “24Hours” or “12Hours.
12
6
Finish the setting.
To check the clock time when the unit is
turned off, press D (DISP).
The power turns on and the clock time is shown
for about 5 seconds, then the power turns off.
EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM9
10
ENGLISH
RADIO OPERATIONS
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching a station automatically:
Auto search
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the band (FM1 – 3, AM).
Each time you press the button,
the band changes as follows:
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
3
Start searching a station.
When a station is received, searching stops.
To stop searching before a station is received,
press the same button you have pressed for
searching.
Searching a station manually:
Manual search
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the band (FM1 – 3, AM).
Each time you press the button,
the band changes as follows:
Selected band appears.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
To search stations of
higher frequencies
To search stations of lower frequencies
FM1 FM2 FM3 AM
FM1 FM2 FM3 AM
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM10
11
ENGLISH
3
Press and hold ¢ or 4
until “Manual Search” starts flashing
on the display.
4
Tune in to a station you want while
“Manual Search” is flashing.
If you release your finger from the button,
the manual mode automatically turns off
after about 5 seconds.
If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz for AM—MW/LW) until you
release the button.
If the sound quality decreases and the
stereo effect is lost while listening to an
FM station
In some areas, adjacent stations may
interfere with each other. If this interference
occurs, this unit can automatically reduce this
interference noise (the initial setting when
shipped from the factory). However, in this
case, the sound quality will be degraded and
the stereo effect will also be lost.
If you do not want to degrade the sound
quality and to lose the stereo effect, rather
than to eliminate the interference noise, see
“To change the FM tuner selectivity—IF Filter”
on page 56.
To tune in to stations of lower frequencies
To tune in to stations
of higher frequencies
To tune in to FM stations only with strong
signals—LO/DX (Local/Distance-extreme)
While searching FM stations (including SSM—
see page 12), this unit stops searching whenever
it detects signals (DX mode: The DX indicator is
lit—initial setting). If received signals are weak,
you may only hear noises.
By setting LO/DX to “Local, you can make this
unit detects only stations with sufficient signal
strength.
1 Press M (MODE) while listening to an FM
broadcast.
“Mode” appears on the display.
The next-step-operation buttons
start flashing.
2 Press number button 2, while “Mode” is still
on the display.
Each time you press the button, the “LO/DX”
setting alternates between “Local” and “DX”.
See page 46 for this function.
After about
5 seconds
The display returns to the source indication
screen.
LO indicator appears
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM11
12
ENGLISH
When an FM stereo broadcast is hard to
receive:
Set the FM reception mode to “Mono On.
1 Press M (MODE) while listening to an FM
stereo broadcast.
“Mode” appears on the display.
The next-step-operation buttons
start flashing.
2 Press number button 1 to select “Mono On”
while “Mode” is still on the display.
Each time you press the button, “Mono On” or
“Mono Off” appears alternately.
The display returns to the source indication
screen.
The sound you hear becomes monaural but the
reception will be improved.
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the FM band (FM1 – 3) you
want to store FM stations into.
Each time you press the button,
the band changes as follows:
3
Start automatic preset.
1 Press M (MODE).
“Mode” appears on the display.
The next-step-operation
buttons start flashing.
2 Press and hold number button 5 while
“Mode” is still on the display.
“SSM” appears, then disappears
when automatic preset is over.
After about
5 seconds
MONO indicator appears.
FM1 FM2 FM3 AM
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM12
13
ENGLISH
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.
Ex.: Storing FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
Each time you press the button,
the band changes as follows:
3
Tune in to a station (in this example,
of 92.5 MHz).
To tune in to stations
of higher frequencies
To tune in to stations of lower frequencies
4
Press and hold the number button
(in this example, 1) for more than
2 seconds.
The display pattern automatically changes
to the small animation display (see page
15).
5
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
A previously preset station is erased when a new
station is stored in the same preset number.
Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.
FM1 FM2 FM3 AM
After about
5 seconds
Preset number appears.
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM13
14
ENGLISH
Selecting a preset station using the
preset station list
If you forget what stations are stored in which
preset numbers, you can check the preset station
list, then select your desired station.
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the band (FM1 – 3, AM).
Each time you press the button,
the band changes as follows:
3
Press and hold 5 (up) or (down)
until the preset station list for the
current band (FM1, FM2, FM3, or AM)
appears on the display.
The current station will be
highlighted on the display.
Ex.: When you select the preset station
number 1 of the FM1 band
Notes:
You can show the other FM band preset station lists
(FM1, FM2, or FM3) by pressing 5 (up) or
(down).
If a preset station is an FM RDS station with PS
(programme station) signal, PS name will be shown
instead of the station frequency.
4
Select the number (1 – 6) for the
preset station you want.
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 12 and 13.
Selecting a preset station directly
1
Select the FM/AM tuner.
Each time you press and hold
the button, the FM/AM tuner
and the DAB tuner are
alternately selected.
2
Select the band (FM1 – 3, AM).
Each time you press the button,
the band changes as follows:
3
Select the number (1 – 6) for the
preset station you want.
FM1 FM2 FM3 AM
FM1 FM2 FM3 AM
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM14
15
ENGLISH
Changing the display pattern
By pressing D (DISP), you can change the information shown on the display.
Each time you press the button, the display patterns change as follows:
When receiving an AM or non FM RDS-
station
When receiving an FM RDS-station
(see the following pages)
Large animation display
Current sound mode
(iEQ) (see page 41)
Appears only when
selecting a preset
station.
Small animation display 1
Clock time
Clock time display
“NO NAME” always appears for AM or FM
non-RDS stations.
Current sound mode
(iEQ) (see page 41)
Small animation display 2
Large animation display
Clock time
PS name
Small animation display 1
Small animation display 2
Clock time display
PTY code appears.
EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM15
16
ENGLISH
RDS OPERATIONS
What you can do with RDS
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations
send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as CD.
By receiving the RDS data, this unit can do the
following:
Tracing the same programme automatically
(Network-Tracking Reception)
Traffic News Standby Reception or your
favorite programme
PTY (Programme Type) search
Programme search
And some other functions
Tracing the same programme
automatically (Network-Tracking
Reception)
When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting the
same programme with stronger signals. So, you
can continue to listen to the same programme in
its finest reception, no matter where you drive.
(See the illustration on page 22.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly
—PI (Programme Identification) and AF
(Alternative Frequency).
Without receiving these data correctly from the
RDS station you are listening to, Network-
Tracking Reception will not operate.
To use Network-Tracking Reception
You can select the different modes of network-
tracking reception to continue listening to the
same programme in its finest reception.
When shipped from the factory, “AF” is selected.
AF: Network-Tracking Reception is
activated without Regionalization.
With this setting, the unit switches to
another station within the same
network when the receiving signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up.
AF Reg: Network-Tracking Reception is
activated with Regionalization.
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the receiving
signals from the current station
become weak.
The REG indicator lights up.
Off*: Network-Tracking Reception is
deactivated.
Neither the AF nor the REG indicator
lights up.
* You can select only when “DAB AF” is
set to “Off.” (See page 54 for details.)
Note:
If Alternative Reception (for DAB services) is
activated, Network-Tracking Reception is also
activated (“AF”) automatically. On the other hand,
Network-Tracking Reception cannot be deactivated
without deactivating Alternative Reception. (See page
29.)
AF or REG indicator lights up.
EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM16
17
ENGLISH
1
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 53 and 54.)
2
Press number button 4 to select
“TUNER”—Tuner category of the
PSM settings.
The “PTY Stnby” (standby) setting screen
appears on the display.
3
Select “AF-Regn’l” (alternative
frequency/regionalization
reception).
4
Select the desired mode—“AF,
“AF Reg, or “Off.
5
Finish the setting.
Using Traffic News Standby Reception
Traffic News Standby Reception allows the unit
to switch temporarily to Traffic Announcement
(TA) from the current source (another FM station,
DAB, CD, or other connected components).
Traffic News Standby Reception will not work if you
are listening to an AM station.
Press TP/PTY to activate Traffic
News Standby Reception.
Each time your press the button,
this function is turned on and off
alternately.
7 When the current source is FM or DAB, the
TP indicator either lights up or flashes.
If the TP indicator lights up, Traffic News
Standby Reception is activated.
If a station (or service) starts broadcasting a
traffic announcement, “Traffic News” appears
on the display, and this unit automatically
tunes in to the station (or service). The
volume changes to the preset TA volume
level (see page 21) and the traffic
announcement can be heard.
If the TP indicator flashes, Traffic News
Standby Reception is not yet activated since
the station (or service) being received does
not provide the signals used for Traffic News
Standby Reception.
To activate Traffic News Standby Reception,
you need to tune in to another station
providing these signals. Press ¢ or
4 to search for such a station.
When a station (or service) providing these
signals is tuned in, the TP indicator stops
flashing and remains lit. Now Traffic News
Standby Reception is activated.
TP indicator appears.
(either lights up or flashes)
CONTINUED ON THE NEXT PAGE
EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM17
18
ENGLISH
7 When the current source is other than FM
or DAB, the TP indicator lights up.
If a station (or service) starts broadcasting a
traffic announcement, “Traffic News” appears
on the display, and this unit automatically
changes the source and tunes in to the station
(or service).
Note:
See also “Traffic News Standby Reception” on page
27.
Using PTY Standby Reception
PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from any source except AM
stations.
See also “Using PTY Standby Reception” on
page 29.
To select your favorite PTY code for PTY
Standby Reception
When shipped from factory, PTY Standby
Reception has been set to search for “News”
programmes.
You can select your favorite programme type for
PTY Standby Reception.
1
Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see pages 53 and 54.)
2
Press number button 4 to select
“TUNER”—Tuner category of the
PSM settings.
The “PTY Stnby” (standby) setting screen
appears on the display.
3
Select one of the twenty-nine PTY
codes. (See page 22.)
Selected code name
appears on the display
and is stored into
memory.
4
Finish the setting.
To set PTY Standby Reception
1 Press M (MODE) while listening to an FM
broadcast (or a DAB service).
“Mode” appears on the display.
The next-step-operation buttons
start flashing.
2 Press number button 3 to activate PTY
Standby Reception while “Mode” is still on the
display.
Each time you press the button, PTY Standby
Reception turns on and off alternately.
The display returns to the source indication
screen.
Ex.: When the currently selected PTY code
for PTY Standby Reception is “News”
PTY indicator appears.
(either lights up or flashes)
After about
5 seconds
EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM18
19
ENGLISH
Searching for your favorite programme
You can search for any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.
When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).
See also “Searching for your favorite service”
on page 29.
To store your favorite programme types, see
below.
To search for your favorite programme type,
see page 20.
To store your favorite programme types
1
Press and hold TP/PTY for more
than 2 seconds while listening to an
FM station (or a DAB service).
The last selected PTY code
appears.
2
Select one of the twenty-nine PTY
codes. (See page 22.)
Selected code name
appears on the display.
The PTY indicator either lights up or flashes.
If the PTY indicator lights up, PTY Standby
Reception is activated.
If a station (or service) starts broadcasting the
selected PTY programme, this unit
automatically tunes in to the station (or
service).
If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the station
(or service) being received does not provide
the signals used for PTY Standby Reception.
To activate PTY Standby Reception, you need
to tune in to another station (or service)
providing these signals. Press ¢ or
4 to search for such a station.
When a station (or service) providing these
signals is tuned in, the PTY indicator stops
flashing and remains lit. Now PTY Standby
Reception is activated.
Note:
After turning on PTY Standby Reception, you can
change the source without canceling PTY Standby
Reception. In this case, the PTY indicator stops
flashing if it was. If a station (or service) starts
broadcasting the selected PTY programme, this unit
automatically changes the source and tunes in to the
station (or service).
If you change the source to AM, PTY Standby
Reception will be temporarily canceled.
You can only deactivate the PTY Standby Reception
when the source is FM or DAB.
Ex.: If you have selected “Pop M” previously
Pop M
1
2
3
Rock M Easy M
45
6
Classics
Affairs
Varied
CONTINUED ON THE NEXT PAGE
EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM19
20
ENGLISH
3
Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset
number you want.
Selected preset number flashes for a while.
4
Press and hold TP/PTY for more than
2 seconds to exit from this mode.
To search for your favorite programme
type
1
Press and hold TP/PTY for more
than 2 seconds while listening to an
FM station (or a DAB service).
The last selected PTY code
appears.
2
To select one of your favorite
programme type
or
To select any one of the twenty-nine
PTY codes
How to use the
5
(up) or
(down) button
By pressing 5 (up) or (down) repeatedly,
you can show the list of your preset PTY
codes and all twenty-nine PTY codes (six
PTY codes at a time). First, the list of your
stored PTY codes appears, then all twenty-
nine PTY codes (six PTY codes at a time)
appears in sequence.
Press the number button to select your
desired PTY code on the list currently shown
on the display.
3
Start PTY search for your favorite
programme.
If there is a station (or service) broadcasting a
programme of the same PTY code as you have
selected, that station (or service) is tuned in.
If there is no station (or service) broadcasting a
programme of the same PTY code as you have
selected, the station (or service) will not
change.
Note:
In some areas, the PTY search will not work correctly.
Ex.: When Rock M is selected
or
Ex.: If you have selected Pop M previously
EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291

JVC EXAD KD-LHX601 Manuel utilisateur

Catégorie
Récepteurs multimédia de voiture
Taper
Manuel utilisateur
Ce manuel convient également à