JVC EXAD KD-LHX601 Manuel utilisateur

LVT1119-001A

[E/EX]

KD-LHX601

CD RECEIVER

CD-RECEIVER

RECEPTEUR CD

CD-RECEIVER

ENGLISH

DEUTSCH

NEDERLANDS

FRANÇAIS

For installation and connections, refer to the separate manual.

Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.

Pour l’installation et les raccordements, se référer au manuel séparé.

Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende

handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

• This unit is equipped with the display demonstration. To cancel it, see page 8.

• Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf Seite 8 wird

beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.

• Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-

vous à la page 8.

• Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 8 voor het annuleren van deze

functie.

Cover_001A_KD-LHX601[E_EX].p65 04.1.15, 2:27 PM3

2

ENGLISH

How to reset your unit

Press the reset button on the control panel using a ball-

point pen or a similar tool.

This will reset the built-in

microcomputer.

Note:

Your preset adjustments—such

as preset channels or sound

adjustments—will also be

erased.

Caution:

If the temperature inside the car is below 0˚ C, the movement of animation and text scroll will be halted on

the display to prevent the display from being blurred. (LOW TEMP.) indicator appears on the display.

When the temperature increases, the operating temperature is resumed, and these functions will start

working again.

CAUTION on Volume Setting:

Discs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for

example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the

volume before playing a disc and adjust it as required during playback.

Note:

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on

the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

CAUTION:

NEVER insert your finger in

between the control panel and

the unit, as it may

get caught or

hurt.

(See page 61.)

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid

direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

EN02-03_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM2

3

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit ............................... 2

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Illumination Navigation for easy operations ...

4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Canceling the display demonstration ........ 8

Setting the clock ........................................ 9

RADIO OPERATIONS ...................... 10

Listening to the radio ................................. 10

Storing stations in memory ....................... 12

Tuning in to a preset station ...................... 14

Changing the display pattern .................... 15

RDS OPERATIONS ......................... 16

What you can do with RDS ....................... 16

Other convenient RDS functions and

adjustments ............................................ 21

DAB TUNER OPERATIONS ................ 23

Tuning in to an ensemble and one of the

services .................................................. 23

Storing DAB services in memory .............. 25

Tuning in to a preset DAB service ............. 25

What you can do more with DAB .............. 27

Changing the display pattern .................... 30

DISC OPERATIONS ........................ 31

About MP3 and WMA discs ...................... 31

Playing a disc ............................................ 31

Locating a track or a particular portion

on a disc ................................................. 34

Selecting a folder and a track using the

name lists ............................................... 36

Selecting the playback modes .................. 37

Prohibiting disc ejection ............................ 38

Changing the display pattern .................... 39

SOUND ADJUSTMENTS ................... 40

Adjusting the sound .................................. 40

Selecting preset sound modes

(iEQ: intelligent equalizer) ...................... 41

Storing your own sound modes ................ 43

Selecting the display theme ...................... 44

GRAPHIC DISPLAYS ........................ 45

Downloading images and animations ....... 46

Deleting unwanted files ............................. 48

Activating the downloaded images and

animations .............................................. 50

OTHER MAIN FUNCTIONS ................ 52

Changing the general settings (PSM) ....... 52

Selecting the dimmer mode ...................... 57

Changing the display color ........................ 58

Assigning names to the sources ................ 60

Changing the control panel angle .............. 61

Detaching the control panel ...................... 61

CD CHANGER OPERATIONS .............. 62

Playing discs ............................................. 62

Selecting a disc/folder/track using the

name lists ............................................... 65

Selecting the playback modes .................. 66

EXTERNAL COMPONENT OPERATIONS ... 68

Playing an external component ................. 68

Changing the display pattern .................... 68

TROUBLESHOOTING ...................... 69

MAINTENANCE ............................. 72

Handling discs ........................................... 72

SPECIFICATIONS ........................... 73

*Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

BEFORE USE

*For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

EN02-03_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM3

ENGLISH

4

LOCATION OF THE BUTTONS

Control panel

Illumination Navigation for easy operations

If you use M (MODE) or SEL (select), the display and some controls (such as the number buttons,

4 /¢ , 5/∞, and control dial) enter the corresponding control mode, then the controls

start flashing to lead you to the next operational steps. (Illumination Navigation)

• The display shows how these buttons function during this period.

Ex.: When you press number button 1 after pressing M (MODE), to operate the FM tuner.

To use these controls for original functions again, wait until the controls stop flashing without

using these controls.

• Pressing M (MODE) again also restores original functions. However, pressing SEL (select)

makes the unit into a different mode.

Time countdown indicator

1 (standby/on/attenuator) button

2 TP/PTY (traffic programme/programme type)

button

3 Control dial

4 Display window

5 FM/AM DAB button

6 5 (up) button

7 0 (eject) button

(angle) button

8 4 /¢ buttons

9 SEL (select) button

p D (DISP: display) button

q Number buttons

w M (MODE) button

e Remote sensor

r ∞ (down) button

t CD/CD-CH (CD changer) LINE button

y (control panel release) button

EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM4

ENGLISH

5

Remote controller

3 • Selects the preset stations or service while

listening to the radio or the DAB tuner.

Each time you press the button, the preset

station or service number increases, and the

selected station or service is tuned in.

• Skips to the first track of the previous folder

while listening to an MP3 disc or a WMA

disc.

Each time you press the button, you can

move to the previous folder and start playing

the first track.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the previous disc if pressed

briefly.

– Skips to the previous folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the previous disc.

4 Selects the sound mode (iEQ: intelligent

equalizer).

Each time you press the button, the sound

mode (iEQ) changes.

5 • Selects the band while listening to the radio

or the DAB tuner.

Each time you press the button, the band

changes.

• Skips to the first track of the next folder while

listening to an MP3 disc or a WMA disc.

Each time you press the button, you can

move to the next folder and start playing the

first track.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the next disc if pressed briefly.

– Skips to the next folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the next disc.

6 Selects the source.

Each time you press the button, the source

changes.

7 Functions the same as the control dial on the

main unit.

Note:

These buttons do not function for the

preferred setting mode (PSM) adjustment.

1 • Turns on the unit if pressed when the unit is

turned off.

• Turns off the unit if pressed and held for a

few seconds.

• Drops the volume level in a moment if

pressed briefly.

Press again to resume the volume.

2 • Searches for stations while listening to the

radio.

• Selects services while listening to the DAB

tuner if pressed briefly.

• Searches for ensembles while listening to

the DAB tuner if pressed for more than one

second.

• Fast-forwards or reverses the track if

pressed and held while listening to a disc.

• Skips to the beginning of the next track or

goes back to the beginning of the current (or

previous) tracks if pressed briefly while

listening to a disc.

EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM5

ENGLISH

6

Preparing the remote controller

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

• Do not expose the remote sensor to strong

light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness of

the remote controller decreases, replace the

battery.

1. Remove the battery holder.

1) Push out the battery holder in the direction

indicated by the arrow using a ball-point

pen or a similar tool.

2) Remove the battery holder.

2. Place the battery.

Slide the battery into the holder with the +

side facing upwards so that the battery is

fixed in the holder.

Lithium coin

battery (product

number: CR2025)

(back side)

Remote sensor

(back side)

3. Return the battery holder.

Insert again the battery holder by pushing it

until you hear a clicking sound.

WARNING:

• Store the battery in a place where children

cannot reach.

If a child accidentally swallows the battery,

consult a doctor immediately.

• Do not recharge, short, disassemble, or heat the

battery or dispose of it in a fire.

Doing any of these things may cause the battery

to give off heat, crack, or start a fire.

• Do not leave the battery with other metallic

materials.

Doing this may cause the battery to give off

heat, crack, or start a fire.

• When throwing away or saving the battery,

wrap it in tape and insulate; otherwise, the

battery may start to give off heat, crack, or start

a fire.

• Do not poke the battery with tweezers or similar

tools.

Doing this may cause the battery to give off

heat, crack, or start a fire.

CAUTION:

DO NOT leave the remote controller in a place

(such as dashboards) exposed to direct sunlight for

a long time. Otherwise, it may be damaged.

KD-LHX601 is equipped with the steering

wheel remote control function.

If your car is equipped with the steering wheel

remote controller, you can operate this

receiver using the controller.

• See the Installation/Connection Manual

(separate volume) for connection to utilize

this function.

EN04-06_KD-LHX601[E_EX].p65 04.1.15, 2:28 PM6

7

ENGLISH

3

Adjust the volume.

4

Adjust the sound as you want.

(See pages 40 – 43.)

Note:

While playing a source, you can select the display

theme of your preference. For details, see “Selecting

the display theme” on page 44.

NOTICE:

The illustrations of the display used in this manual

are mainly of the initial setting when shipped from

the factory. If you have changed the display

patterns or some PSM items, the actual displays

you see will be different.

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

2

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

2

Select the source.

• To operate the FM/AM tuner or the DAB

tuner, press and hold FM/AM DAB

repeatedly.

• To operate the CD player (CD),

CD changer (CD-CH), or external

component (LINE-IN), press

CD/CD-CH LINE repeatedly.

*

1

If there is no disc in the loading slot, you

cannot select “CD” as the source, “No

Disc” flashes on the display.

*

2

Without connecting the CD changer, you

cannot select “CD-CH” as the source to

play.

BASIC OPERATIONS

To increase the volume

To decrease the volume

Volume level appears.

Current sound mode (iEQ)

(see page 41)

1

2

3

EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM7

8

ENGLISH

To drop the volume in a moment

Press briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

• If you turn the control dial, you can also restore

the sound.

To turn off the power

Press and hold for more than one

second.

• If you turn off the power while listening to a

disc, disc play will start from where playback

has been stopped previously, next time you

turn on the power.

Canceling the display

demonstration

When shipped from the factory, display

demonstration has been activated, and starts

automatically when no operations are done for

about 20 seconds.

• It is recommended to cancel the demonstration

before you use the unit for the first time.

To cancel the display demonstration, follow

the procedure below:

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 53 and 54.)

The next-step-operation

buttons start flashing.

2

Press number button 1 to select

“MOVIE”—Movie category of the

PSM settings.

The “Graphics” setting screen appears on

the display.

3

Select “Off.”

4

Finish the setting.

To activate the display demonstration, repeat

the same procedure and select “Int Demo” or “All

Demo” in step

3

.

• For more details, see “To show the graphics on

the display—Graphics” on page 55.

EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM8

9

ENGLISH

Setting the clock

You can also set the clock system to either

24 hours or 12 hours.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 53 and 54.)

The next-step-operation

buttons start flashing.

2

Press number button 2 to select

“CLOCK”—Clock category of the

PSM settings.

The “Clock Hr” (hour) setting screen

appears on the display.

3

Adjust the hour.

4

Set the minute.

1 Select “Clock Min” (minute).

2 Adjust the minute.

12

5

Set the clock system.

1 Select “24H/12H.”

2 Select “24Hours” or “12Hours.”

12

6

Finish the setting.

To check the clock time when the unit is

turned off, press D (DISP).

The power turns on and the clock time is shown

for about 5 seconds, then the power turns off.

EN07-09_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM9

10

ENGLISH

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching a station automatically:

Auto search

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the band (FM1 – 3, AM).

Each time you press the button,

the band changes as follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

3

Start searching a station.

When a station is received, searching stops.

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the band (FM1 – 3, AM).

Each time you press the button,

the band changes as follows:

Selected band appears.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

To search stations of

higher frequencies

To search stations of lower frequencies

FM1 FM2 FM3 AM

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM10

11

ENGLISH

3

Press and hold ¢ or 4

until “Manual Search” starts flashing

on the display.

4

Tune in to a station you want while

“Manual Search” is flashing.

• If you release your finger from the button,

the manual mode automatically turns off

after about 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 50 kHz intervals for

FM and 9 kHz for AM—MW/LW) until you

release the button.

If the sound quality decreases and the

stereo effect is lost while listening to an

FM station

In some areas, adjacent stations may

interfere with each other. If this interference

occurs, this unit can automatically reduce this

interference noise (the initial setting when

shipped from the factory). However, in this

case, the sound quality will be degraded and

the stereo effect will also be lost.

If you do not want to degrade the sound

quality and to lose the stereo effect, rather

than to eliminate the interference noise, see

“To change the FM tuner selectivity—IF Filter”

on page 56.

To tune in to stations of lower frequencies

To tune in to stations

of higher frequencies

To tune in to FM stations only with strong

signals—LO/DX (Local/Distance-extreme)

While searching FM stations (including SSM—

see page 12), this unit stops searching whenever

it detects signals (DX mode: The DX indicator is

lit—initial setting). If received signals are weak,

you may only hear noises.

By setting LO/DX to “Local,” you can make this

unit detects only stations with sufficient signal

strength.

1 Press M (MODE) while listening to an FM

broadcast.

“Mode” appears on the display.

The next-step-operation buttons

start flashing.

2 Press number button 2, while “Mode” is still

on the display.

Each time you press the button, the “LO/DX”

setting alternates between “Local” and “DX”.

See page 46 for this function.

After about

5 seconds

The display returns to the source indication

screen.

LO indicator appears

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM11

12

ENGLISH

When an FM stereo broadcast is hard to

receive:

Set the FM reception mode to “Mono On.”

1 Press M (MODE) while listening to an FM

stereo broadcast.

“Mode” appears on the display.

The next-step-operation buttons

start flashing.

2 Press number button 1 to select “Mono On”

while “Mode” is still on the display.

Each time you press the button, “Mono On” or

“Mono Off” appears alternately.

The display returns to the source indication

screen.

The sound you hear becomes monaural but the

reception will be improved.

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the FM band (FM1 – 3) you

want to store FM stations into.

Each time you press the button,

the band changes as follows:

3

Start automatic preset.

1 Press M (MODE).

“Mode” appears on the display.

The next-step-operation

buttons start flashing.

2 Press and hold number button 5 while

“Mode” is still on the display.

“SSM” appears, then disappears

when automatic preset is over.

After about

5 seconds

MONO indicator appears.

FM1 FM2 FM3 AM

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM12

13

ENGLISH

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the button,

the band changes as follows:

3

Tune in to a station (in this example,

of 92.5 MHz).

To tune in to stations

of higher frequencies

To tune in to stations of lower frequencies

4

Press and hold the number button

(in this example, 1) for more than

2 seconds.

The display pattern automatically changes

to the small animation display (see page

15).

5

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

FM1 FM2 FM3 AM

After about

5 seconds

Preset number appears.

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM13

14

ENGLISH

Selecting a preset station using the

preset station list

If you forget what stations are stored in which

preset numbers, you can check the preset station

list, then select your desired station.

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the band (FM1 – 3, AM).

Each time you press the button,

the band changes as follows:

3

Press and hold 5 (up) or ∞ (down)

until the preset station list for the

current band (FM1, FM2, FM3, or AM)

appears on the display.

The current station will be

highlighted on the display.

Ex.: When you select the preset station

number 1 of the FM1 band

Notes:

• You can show the other FM band preset station lists

(FM1, FM2, or FM3) by pressing 5 (up) or ∞

(down).

• If a preset station is an FM RDS station with PS

(programme station) signal, PS name will be shown

instead of the station frequency.

4

Select the number (1 – 6) for the

preset station you want.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 12 and 13.

Selecting a preset station directly

1

Select the FM/AM tuner.

Each time you press and hold

the button, the FM/AM tuner

and the DAB tuner are

alternately selected.

2

Select the band (FM1 – 3, AM).

Each time you press the button,

the band changes as follows:

3

Select the number (1 – 6) for the

preset station you want.

FM1 FM2 FM3 AM

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM14

15

ENGLISH

Changing the display pattern

By pressing D (DISP), you can change the information shown on the display.

Each time you press the button, the display patterns change as follows:

• When receiving an AM or non FM RDS-

station

• When receiving an FM RDS-station

(see the following pages)

Large animation display

Current sound mode

(iEQ) (see page 41)

Appears only when

selecting a preset

station.

Small animation display 1

Clock time

Clock time display

“NO NAME” always appears for AM or FM

non-RDS stations.

Current sound mode

(iEQ) (see page 41)

Small animation display 2

Large animation display

Clock time

PS name

Small animation display 1

Small animation display 2

Clock time display

PTY code appears.

EN10-15_KD-LHX601[E_EX].p65 04.1.15, 2:29 PM15

16

ENGLISH

RDS OPERATIONS

What you can do with RDS

RDS (Radio Data System) allows FM stations to

send an additional signal along with their regular

programme signals. For example, the stations

send their station names, as well as information

about what type of programme they broadcast,

such as sports or music, etc.

Another advantage of RDS function is called

“Enhanced Other Networks.” By using the

Enhanced Other Networks data sent from a

station, you can tune in to a different station of a

different network broadcasting your favorite

programme or traffic announcement while

listening to another programme or to another

source such as CD.

By receiving the RDS data, this unit can do the

following:

• Tracing the same programme automatically

(Network-Tracking Reception)

• Traffic News Standby Reception or your

favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

Tracing the same programme

automatically (Network-Tracking

Reception)

When driving in an area where FM reception is

not good, the tuner built in this unit automatically

tunes in to another RDS station, broadcasting the

same programme with stronger signals. So, you

can continue to listen to the same programme in

its finest reception, no matter where you drive.

(See the illustration on page 22.)

Two types of the RDS data are used to make

Network-Tracking Reception work correctly

—PI (Programme Identification) and AF

(Alternative Frequency).

Without receiving these data correctly from the

RDS station you are listening to, Network-

Tracking Reception will not operate.

To use Network-Tracking Reception

You can select the different modes of network-

tracking reception to continue listening to the

same programme in its finest reception.

When shipped from the factory, “AF” is selected.

• AF: Network-Tracking Reception is

activated without Regionalization.

With this setting, the unit switches to

another station within the same

network when the receiving signals

from the current station become

weak. (In this mode, the programme

may differ from the one currently

received.)

The AF indicator lights up.

• AF Reg: Network-Tracking Reception is

activated with Regionalization.

With this setting, the unit switches to

another station, within the same

network, broadcasting the same

programme when the receiving

signals from the current station

become weak.

The REG indicator lights up.

• Off*: Network-Tracking Reception is

deactivated.

Neither the AF nor the REG indicator

lights up.

* You can select only when “DAB AF” is

set to “Off.” (See page 54 for details.)

Note:

If Alternative Reception (for DAB services) is

activated, Network-Tracking Reception is also

activated (“AF”) automatically. On the other hand,

Network-Tracking Reception cannot be deactivated

without deactivating Alternative Reception. (See page

29.)

AF or REG indicator lights up.

EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM16

17

ENGLISH

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 53 and 54.)

2

Press number button 4 to select

“TUNER”—Tuner category of the

PSM settings.

The “PTY Stnby” (standby) setting screen

appears on the display.

3

Select “AF-Regn’l” (alternative

frequency/regionalization

reception).

4

Select the desired mode—“AF,”

“AF Reg,” or “Off.”

5

Finish the setting.

Using Traffic News Standby Reception

Traffic News Standby Reception allows the unit

to switch temporarily to Traffic Announcement

(TA) from the current source (another FM station,

DAB, CD, or other connected components).

• Traffic News Standby Reception will not work if you

are listening to an AM station.

Press TP/PTY to activate Traffic

News Standby Reception.

Each time your press the button,

this function is turned on and off

alternately.

7 When the current source is FM or DAB, the

TP indicator either lights up or flashes.

• If the TP indicator lights up, Traffic News

Standby Reception is activated.

If a station (or service) starts broadcasting a

traffic announcement, “Traffic News” appears

on the display, and this unit automatically

tunes in to the station (or service). The

volume changes to the preset TA volume

level (see page 21) and the traffic

announcement can be heard.

• If the TP indicator flashes, Traffic News

Standby Reception is not yet activated since

the station (or service) being received does

not provide the signals used for Traffic News

Standby Reception.

To activate Traffic News Standby Reception,

you need to tune in to another station

providing these signals. Press ¢ or

4 to search for such a station.

When a station (or service) providing these

signals is tuned in, the TP indicator stops

flashing and remains lit. Now Traffic News

Standby Reception is activated.

TP indicator appears.

(either lights up or flashes)

CONTINUED ON THE NEXT PAGE

EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM17

18

ENGLISH

7 When the current source is other than FM

or DAB, the TP indicator lights up.

If a station (or service) starts broadcasting a

traffic announcement, “Traffic News” appears

on the display, and this unit automatically

changes the source and tunes in to the station

(or service).

Note:

See also “Traffic News Standby Reception” on page

27.

Using PTY Standby Reception

PTY Standby Reception allows the unit to switch

temporarily to your favorite programme (PTY:

Programme Type) from any source except AM

stations.

• See also “Using PTY Standby Reception” on

page 29.

To select your favorite PTY code for PTY

Standby Reception

When shipped from factory, PTY Standby

Reception has been set to search for “News”

programmes.

You can select your favorite programme type for

PTY Standby Reception.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 53 and 54.)

2

Press number button 4 to select

“TUNER”—Tuner category of the

PSM settings.

The “PTY Stnby” (standby) setting screen

appears on the display.

3

Select one of the twenty-nine PTY

codes. (See page 22.)

Selected code name

appears on the display

and is stored into

memory.

4

Finish the setting.

To set PTY Standby Reception

1 Press M (MODE) while listening to an FM

broadcast (or a DAB service).

“Mode” appears on the display.

The next-step-operation buttons

start flashing.

2 Press number button 3 to activate PTY

Standby Reception while “Mode” is still on the

display.

Each time you press the button, PTY Standby

Reception turns on and off alternately.

The display returns to the source indication

screen.

Ex.: When the currently selected PTY code

for PTY Standby Reception is “News”

PTY indicator appears.

(either lights up or flashes)

After about

5 seconds

EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM18

19

ENGLISH

Searching for your favorite programme

You can search for any one of the PTY codes.

In addition, you can store your 6 favorite

programme types in the number buttons.

When shipped from the factory, the following

6 programme types have been stored in the

number buttons (1 to 6).

• See also “Searching for your favorite service”

on page 29.

To store your favorite programme types, see

below.

To search for your favorite programme type,

see page 20.

To store your favorite programme types

1

Press and hold TP/PTY for more

than 2 seconds while listening to an

FM station (or a DAB service).

The last selected PTY code

appears.

2

Select one of the twenty-nine PTY

codes. (See page 22.)

Selected code name

appears on the display.

The PTY indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby

Reception is activated.

If a station (or service) starts broadcasting the

selected PTY programme, this unit

automatically tunes in to the station (or

service).

• If the PTY indicator flashes, PTY Standby

Reception is not yet activated since the station

(or service) being received does not provide

the signals used for PTY Standby Reception.

To activate PTY Standby Reception, you need

to tune in to another station (or service)

providing these signals. Press ¢ or

4 to search for such a station.

When a station (or service) providing these

signals is tuned in, the PTY indicator stops

flashing and remains lit. Now PTY Standby

Reception is activated.

Note:

After turning on PTY Standby Reception, you can

change the source without canceling PTY Standby

Reception. In this case, the PTY indicator stops

flashing if it was. If a station (or service) starts

broadcasting the selected PTY programme, this unit

automatically changes the source and tunes in to the

station (or service).

• If you change the source to AM, PTY Standby

Reception will be temporarily canceled.

• You can only deactivate the PTY Standby Reception

when the source is FM or DAB.

Ex.: If you have selected “Pop M” previously

Pop M

1

2

3

Rock M Easy M

45

6

Classics

Affairs

Varied

CONTINUED ON THE NEXT PAGE

EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM19

20

ENGLISH

3

Press and hold the number button

for more than 2 seconds to store the

PTY code selected into the preset

number you want.

Selected preset number flashes for a while.

4

Press and hold TP/PTY for more than

2 seconds to exit from this mode.

To search for your favorite programme

type

1

Press and hold TP/PTY for more

than 2 seconds while listening to an

FM station (or a DAB service).

The last selected PTY code

appears.

2

To select one of your favorite

programme type

or

To select any one of the twenty-nine

PTY codes

How to use the

5

(up) or

∞

(down) button

By pressing 5 (up) or ∞ (down) repeatedly,

you can show the list of your preset PTY

codes and all twenty-nine PTY codes (six

PTY codes at a time). First, the list of your

stored PTY codes appears, then all twenty-

nine PTY codes (six PTY codes at a time)

appears in sequence.

Press the number button to select your

desired PTY code on the list currently shown

on the display.

3

Start PTY search for your favorite

programme.

• If there is a station (or service) broadcasting a

programme of the same PTY code as you have

selected, that station (or service) is tuned in.

• If there is no station (or service) broadcasting a

programme of the same PTY code as you have

selected, the station (or service) will not

change.

Note:

In some areas, the PTY search will not work correctly.

Ex.: When “Rock M” is selected

or

Ex.: If you have selected “Pop M” previously

EN16-22_KD-LHX601[E_EX].p65 04.1.15, 2:30 PM20

La page charge ...

JVC EXAD KD-LHX601 Manuel utilisateur

Ce manuel convient également à

JVC EXAD KD-LHX601 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents