Interpump BOXJET TURBO 8.70 Operating Instructions Manual

• OPERATING INSTRUCTIONS

• MODE D’EMPLOI

• BEDIENUNGSANLEITUNG

• INSTRUCCIONES PARA EL USO

• MANUAL DE INSTRUÇÕES

• ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

• LIBRETTO ISTRUZIONI

• DO NOT USE THE MACHINE WITHOUT FIRST READING THE OPERATING INSTRUCTIONS

• N’UTILISER L’APPAREIL QU’APRÈS AVOIR LU LE MANUEL D’INSTRUCTIONS

• GERAT ERST NACH LESEN DER BEDIENUNGSANLEITUNG VERWENDEN

• NO UTILISE EL APARATO SIN LEER ANTES LAS INSTRUCCIONES PARA SU USO

• NÃO USE A MÁQUINA SEM LER A MANUAL DE INSTRUÇÕES

•• НЕ ИСПОЛЬЗУЙТЕ УСТРОЙСТВО, НЕ ПРОЧИТАВ СНАЧАЛА ИНСТРУКЦИЮ ПО ЭКСПЛУАТАЦИИ

• NON USARE LA MACCHINA SENZA AVERE LETTO LE ISTRUZIONI PER L’USO

BBOOXXJJEETT

TURBO 8.70

TURBO 8.90

TURBO 11.50

TURBO 15

TURBO 19

TURBO 21

1

INDEX

ENGLISH............................................................................................ pag.

FRANÇAIS....................................................................................... pag.

DEUTSCH......................................................................................... pag.

ESPAÑOL........................................................................................... pag.

PORTUGUÉS................................................................................ pag.

РУССКИЙ......................................................................................... стр..

ITALIANO........................................................................................... pag.

PART LIST........................................................................................ pag.

LISTE DE PIÈCES DÉTACHÉES........................... pag.

ERSATZTEILLISTE................................................................. pag.

LISTA DE REPUESTOS.................................................... pag.

LISTA DE PEÇAS DE REPOSIÇAO................... pag.

ВЕДОМОСТЬ ЗАПАСНЫХ ЧАСТЕЙ

........... pag.

NOMENCLATURA RICAMBI..................................... pag.

OPTIONALS......................................................................... pag.

4

20

36

52

68

84

100

117

128-129

2

• CONTROL DEVICES

Before connecting the machine to the water and electrical supplies, it is necessary to know the function of the controls

on the machine. This must be done in accordance with the descriptions in the Instruction Manual, taking

reference to the relevant instructions and illustrations.

• DISPOSITIFS DE CONTRÔLE

Avant de brancher l’appareil sur les réseaux d’alimentation d’eau et d’électricité, il est nécessaire de bien connaître le

fonctionnement de ses dispositifs de contrôle. Effectuer cette opération en vous référant aux instructions données

dans ce manuel et aux indications et illustrations y relatives.

• BEDIENUNGS - UND KONTROLLVORRICHTUNGEN

Bevor Sie das Gerät mit Wasser - und Stromanschlüssen verbinden ist es notwending, daß Sie die Bedienungs-und

Kontrollvorrichtungen des Gerätes verstehen. Bitte lesen Sie die Beschreibungen und Illustrationen der

Bedienungsanleitung.

• DISPOSITIVOS DE PUESTA EN MARCHA Y CONTROL

Antes de conectar el equipo a las redes de alimentación de agua y electricidad, es necesario conocer sus dispositivos

de puesta en marcha y control. Efectuar estas operaciones siguiendo las indicaciones que figuran en el manual de

istrucciones así como de sus ilustraciones grafícas correspondientes.

• DISPOSITIVO DE COMANDO E CONTROLO

Antes da ligação às redes de alimentação hídrica e eléctrica, é necessário saber qual a função dos dispositivos de

comando e controlo da máquina. Efectuar esta operação conforme descrito no Manual de Instruções.

• УСТРОЙСТВА УПРАВЛЕНИЯ

Перед тем, как подсоединить изделие к источникам воды и электроэнергии, необходимо изучить его

устройства управления. Это необходимо сделать в соответствии с описаниями, содержащимися в настоящей

Инструкции по экплуатации, уделяя внимание соответствующим инструкциям и иллюстрациям.

• DISPOSITIVI DI COMANDO E CONTROLLO

Prima dell’allacciamento alla rete di alimentazione idrica ed elettrica è necessario conoscere la funzione dei dispositivi

di comando e controllo della macchina. Effettuare questa operazione seguendo quanto descritto nel Manuale Istruzioni

facendo riferimento alle indicazioni e illustrazioni relative.

BB

BBOO

OOXX

XXJJ

JJEE

EETT

TT

3

STANDARD EQUIPMENT

Inlet hose connection with water filter (INLET)

High pressure hose connection (OUTLET)

 Pressure adjusting knob

Pressure indicator

 ON/OFF switch

 Chemical regulator (CHEM)

Chemical filter

Oil dipstick

Oil level indicator

Automatic gun

“QUICK-LANCE”

ROTOTEK (or “MULTIREG”)

High pressure hose

Safety lock

ÉQUIPEMENT STANDARD

Raccord d’alimentation eau et filtre (INLET)

Raccord de tuyau haute pression (OUTLET)

Bouton de régulation de la pression

Indicateur de pression

Interrupteur Marche/Arrêt

Molette de dosage du détérgent (CHEM)

Crépine du détérgent

Jauge de remplissage d’huile

Voyant du niveau d’huile

Pistolet automatique de sécurité

Lance à raccordement rapide “QUICK-LANCE”

ROTOTEK (ou “MULTIREG”)

Tuyau haute pression

Cran de sûreté

STANDARDAUSRÜSTUNG

Wasser-Anschluß mit Filter (INLET)

Hochdruck-Ausgang (OUTLET)

Druckregel-Griff

Druckanzeiger

EIN/AUS Schalter

Chemie-Dosierung (CHEM)

Chemie-filter

Ölmeßstab

Ölstandsanzeige

Spritzpistole

Wechsel-Lanze “QUICK-LANCE”

ROTOTEK (oder “MULTIREG”)

Hochdruckschlauch

Sicherheitssperre

EQUIPO STANDARD

Entrada + filtro agua (INLET)

Salida (OUTLET)

Mando de regulación de la presión

Manómetro

Interruptor

Mando de regul. del detergente (CHEM)

Filtro del detergente

Tapón de aceite con varilla de nivel

Mirilla nível de aceite

Pistola automática

Lanza “QUICK-LANCE”

ROTOTEK (o “MULTIREG”)

Tubo de alta presión

Seguro

EQUIPAMENTO STANDARD

Entrada de água com filtro (INLET)

Conector de saída de alta pressão (OUTLET)

Manípulo de ajuste de pressão

Indicador de pressão

Interruptor líg/des (ON/OFF)

Regulador de detergente (CHEM)

Filtro de aspiração de detergente

Tampa de óleo

Indicador de nivel de óleo

Pistóla automática

Lança

ROTOTEK (ou “MULTIREG”)

Mangueira de alta pressão

Travão

EQUIPAGGIAMENTO STANDARD

Entrata + filtro acqua (INLET)

Uscita (OUTLET)

Manopola di regolazione della pressione

Manometro

Interruttore

Pomolo di regolazione del detersivo (CHEM.)

Filtro detersivo

Tappo carico olio con asta di controllo

Spia livello olio

Pistola automatica

Lancia “QUICK-LANCE”

ROTOTEK (o “MULTIREG”)

Tubo alta pressione

Sicura

СТАНДАРТНОЕ ОБОРУДОВАНИЕ

Вход + Водяной фильтр

Выход (OUTLET)

 Регулятор давления

Манометр

 Выключатель

 Регулировка моющего средства (CHEM)

Фильтр моющего средства

Пробка для заливки масла со стеклом для контроля

Индикатор уровня масла

Пистолет

Гидромонитор

Rototek или Multireg 99

Шланг высокого давления

Предохранитель

4

TABLE OF CONTENTS

1 - Description of symbols on the high pressure cleaner....................................... 5

2 - Technical specifications of the BOXJET............................................................ 6

3 - Product use....................................................................................................... 7

3.1 • Designated use................................................................................... 7

4 - Preliminary operations....................................................................................... 7

4.1 • Unpacking........................................................................................... 7

4.2 • Identification label............................................................................... 8

5 - Installation......................................................................................................... 8

5.1 • Connection high pressure outlet......................................................... 8

5.2 • Connection to water supply................................................................ 9

5.3 • Connection to electric system............................................................ 10

5.3.1 • Cut-out switch (Only the United States).......................................... 10

5.4 • Use of extention cord......................................................................... 11

5.5 • Start-up............................................................................................... 11

6 - General warnings.............................................................................................. 12

7 - Chemical product use....................................................................................... 15

8 - Use of "ROTOTEK" or "MULTIREG 99"............................................................ 15

9 - Precautions againt freezing, and instructions for storage.................................... 16

10 - Maintenance...................................................................................................... 16

10.1 • Oil change......................................................................................... 17

10.2 • Inlet filter............................................................................................ 17

10.3 • Replacement of high pressure nozzle ..............................................17

11 - Machine scrapping............................................................................................ 18

12 - Trouble shooting............................................................................................... 19

ENGLISH

5

1 - DESCRIPTION OF SYMBOLS ON THE HIGH PRESSURE CLEANER

DDoo nnoott ddiirreecctt tthhee jjeett

aaggaaiinnsstt ppeerrssoonnss oorr

aanniimmaallssppoowweerr oouutt--

lleettss oorr tthhee mmaacchhiinnee

iittsseellff..

WWaarrnniinngg!! RRiissk

k ooff

eelleeccttrrooccuuttiioonn

GGrroouunnddiinngg

SSppeecciiaall wwaassttee.. DDoo

nnoott ddiissppoossee ooff tthhiiss

pprroodduucctt iinn nnoorrmmaall

hhoouusseehhoolldd ggaarrbbaag

gee

WWaarrnniinngg ssiiggnn

RReeaadd tthhee iinnssttrruuccttiioonn

mmaannuuaall bbeeffoorree uussee..GGaarraanntteedd ssoouunndd

ppoowweerr lleevveell..

6

2 - TECHNICAL DATA

MODEL

Singlephase

motor power

kW.

Motor protection

Motor protection grade

°C

m/sec2Fixed nozzle A(8) than 2,5 - Rotating nozzle A(8) 3 (uncertainly 0,5)

Max. water inlet

temp °F

m

Max suction depth ft

High pressure hose Thermoplastic material reinforced with nylon braid internal diameter 5/16”

Maximum working pressure 130 bar

Mass

Dimensions mm

inches

Noise level*

Lance vibration*

P.S.I.

Overpressure

peak limit

Recoil thrust of jet N

Flow rate

E.W. bar / MPa / P.S.I.: specific jet pressure in bar / MPa / P.S.I.

Equivalent

washing impact

with rotating

nozzle jet

E.W. MPa

E.W. P.S.I.

Working pressure

MPa

E.W. bar

bar

P.S.I.

MPa

bar

*(Reference Standard EN60335-2-79)

8 m

26 ft

TURBO

21

TURBO

11-50

TURBO

8-70

TURBO

8-90

TURBO

15

TURBO

19

11 l/min. 8 l/min. 8 l/min. 8 l/min. 8 l/min. 2.11 G.P.M.

(USA)

10 14.5 16 12 13 13.8

100 145 160 120 130 138

1450 2100 2320 1750 1885 2000

50 70 90 55 60 70

57 9 5.5 6 7

725 1015 1300 800 870 1015

80 100 120 85 90 100

810 12 8.5 910

1160 1450 1750 1235 1300 1450

20 < 20

Current thermal overload

IPX5

Lp dB(A) 76 (uncertainly 1,5) - Lw dB(A) 90

60

11111

3.3

360x240x235 (h)

14.2x9.4x9.2 (h)

Kg 2< 2

20

2

< 20

< 2

< 20

< 2

< 20

< 2

V.

Hz.

A.

1,68 1,64 1,68 1,64 1,86 1,36 1,40 1,58

230

8,2

240

8

50

230

8,2

240

8

50

230

8,6

240

8,4

50

100

50

15

100

60

15

115

60

15

140

60 60 60 60

Kg

lbs

18,5 18,5 18,7 18,6 19,4

42.8

7

WE CONGRATULATE YOU on your choice that shows your level of technical knowledge and

love of beautiful objects.

In fact, you have purchased a highly technological machine produced by the world's

largest manufacturer of high pressure cleaner pumps.

This machine is so useful and versatile that you will use it for many years.

THIS BOOKLET IS AN INTEGRAL PART OF YOUR MACHINE AND SHOULD BE

CAREFULLY READ BEFORE PROCEEDING WITH INSTALLATION, START-UP AND

USE.

This booklet contains important safety information and instructions for use and maintenance

of the high pressure cleaners BOXJET and should be kept in a safe place.

3. PRODUCT USE

The machine is exclusively designed for washing, by way of a pressurized water jet, objects,

things or any surface suitable for cleaning by a pressurized water jet with the possibility of

adding liquid detergent.

ATTENTION: this appliance was designed for use of detergents recommended by the manu-

facturer. The use of other chemical products may jeopardize the safety of the appliance itself.

The liquid detergent additives must be chosen in consideration of the chemical compatibility

with the components of the pump and of the surface to be cleaned.

IMPORTANT: use only detergents that are biodegradable, and in any case complying with the

regulations applicable in the country where they are used.

3.1 DESIGNATED USE

4. PRELIMINARY OPERATIONS

4.1 UNPACKING

Unpack and make sure that the machine is complete and undamaged.

If the machine appears damaged in any way, do not use the machine and consult our dealer.

For shipping reasons some parts may be included separately. In this case assemble parts as

indicated in this booklet.

Keep all packaging materials (bags, boxes, tape) out of reach of children.

THE DESTINATION OF USE OF THIS MACHINE MUST BE STRICTLY ADHERED TO. ANY

OTHER USE MUST BE CONSIDERED AS INCORRECT.

THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR DAMAGES CAUSED BY

INCORRECT USE OF THE MACHINE.

THE MACHINE MUST NOT BE TAMPERED WITH FOR ANY REASON. IN CASES OF

TAMPERING THE MANUFACTURER DECLINES ANY RESPONSABILITY ON THE FUNC-

TIONING AND SAFETY OF THE MACHINE.

IT IS FORBIDDEN TO STORE OR USE THE UNIT IN ENVIRONMENTS WITH POTEN-

TIALLY EXPLOSIVE ATMOSPHERE.

8

Before using this machine make sure that it has an ID

label. If it is without, do not use the machine and

consult your dealer immediately.

The identification label with technical specifications

is placed on the trolley and is always visible.

Check that ID label specifications correspond to

those required and that the power characteristics

for the outlet (V/Hz) are those shown on the label.

4.2 - ID LABEL

5 - INSTALLATION

5.1 HIGH PRESSURE CONNECTION

Replace the red

travel plug (fig.1)

with the vented

black/yellow

dipstick provided

(fig.2).

Check that the oil in the sight glass is at

the half-way level (fig.3).

1- Connect one end of the high pressure hose to the gun (A) and the other to the outlet con-

nection (B).

2- Assemble the lance by pushing the two halves together and then fix by turning the connec-

tor (C).

9

5.2 - CONNECTION TO THE WATER SUPPLY

1- The maximum temperature of the inlet water must not exceed 60°C (140°F).

2- Connect the water supply to the INLET port (D) by means of a reinforced hose (minimum

1,5 MPa - 15 bar - 200 psi) with internal diameter of no less than 13 mm. (1/2").

3- Since the water flow decreases according to the length of the hose, make sure that the quan-

tity of water supplied to the machine is not less than the quantities indicated in the chart

below.

4- The pressure of the inlet water must not exceed 1 MPa, 10 bar, 145 psi.

ATTENTION: The water supply which enters into the washer is not drinkable.

IMPORTANT

The water supplied to the machine must be clean. Running the unit without water, or with water

which is dirty, contains grit or corrosive liquids, causes serious damage to the machine.

If the user wishes to power the washer by means of free suction, simply emerge the end of the

supply tube in the water to be suctioned. The maximum suction depth considered as the dis-

tance in height between the water surface and the pump is 1m.

D

8•90 - 8•70

15 - 19 - 21

MODEL L/min. G.P.M. USA

11

15

2.9

4

11•50

FLOW RATE OF

WATER SUPPLY

10

5.3 - CONNECTION TO ELECTRICAL SYSTEM

1 - Check that the voltage of the electrical system (mains) is the same as indicated on the ID

label of the machine.

2 - Check that the plug complies with local safety regulations, and that it is provided with

ground connection (earth).

3 - Ensure that the outlet is protected by a "cut-out" (differential magnetic-thermal switch with

sensitivity of less than 30mA per 30ms) or that a device is present which can test the earthing

circuit.

4 - Do not connect other appliances to the same power outlet while using the machine.

5 - Insert the plug only after checking that the machine switch is in the OFF position.

6 - The standard plug for 50 Hz versions: SCHUKO 250V - 16A, standard CEE7-VII

DIN49441-2-AR2.

7- Fully unwind the power cord to prevent overheating.

8 - Do not crush on the power cord.

9 - Do not use the high pressure cleaner if the electric cable is damaged.

10 - If the power cord is damaged, its replacement can be effected only by the technical ser-

vice personnel or by a qualified technician.

WARNING: IN CASE OF POWER FAILURE DURING OPERATION TURN OFF THE

UNIT FOR SAFETY REASONS.

5.3.1 - CUT-OUT SWITCH (Only the United States)

This UL version high-pressure washer is equipped with a cut-out switch contained in the power

cable plug.

Said equipment provides extra protection against the risk of electric shock.

When replacing the plug or cable, use the same components including the cut-out device.

11

5.4 - USE OF CORDS

If an extension cord is used, make sure that plug and receptacle are of a water-tight type. In

any case they must be raised from the ground in order to avoid possible contact with water.

Use only extension cables with the same number of conductors as those of the machine cable,

including the earthing cable, and with a suitable plug/socket for the cable used.

Only use extension cords for outdoor use. Said type of cable is marked "Suitable for outdoor

use." Store inside when not in use.

Do not use damaged extension cords. Cables should not be located near sources of heat or

sharp edges. Always disconnect the plug from the socket before removing the extension cord

from the product. Do not pull the cable to pull the plug out of the outlet. Do not touch the plug

or connections with wet hands.

WARNING

USE OF INADEQUATE

EXTENSION CORDS

MAY CAUSE SAFETY

HAZARDS

SELECTION TABLE

Voltage

220÷240

100÷115

Extension

cord length

Cord section

mm2

Up to 20 m

From 20 to 50 m

Up to 20 m

From 20 to 50 m

1,5

2,5

4

5.5 - START-UP

- Before starting up and using the machine, make sure that it is positioned on the ground or

leaning against a stable support and that the resting surface is level or with a minimum slope.

- It is ESSENTIAL to ensure that the suction filter is clean before use. (see maintenance chap-

ter – 10.2 inlet filter).

1- Open water supply

2- Set the pressure to zero by turning the knob anti-clockwise.

3- Switch on the unit.

4- Hold the gun in the open position for a few seconds to allow the air to escape from hoses.

5- At this point adjust the machine to your pressure requirements and you are ready to enjoy

your work.

Attention! The water pressure at the outlet of the lance generates a force on itself;

therefore, grip the lance with both hands and with a secure grip.

- Switch off the machine when work is completed.

- Open the gun to release pressure still in the hose.

12

6 - GENERAL WARNINGS

High pressure cleaners can be used neither

by children nor by non authorized persons.

Children must be supervised to prevent them

from playing with the machine.

Keep this machine out of reach of children

at all times.

This equipment was not designed to be used

by persons with reduced physical, sensorial or

mental capabilities, or with limited experience

or knowledge, unless a person responsible for

their safety provides them with supervision or

the instructions for the use of the equipment.

NO

Only operate the machine in safety condi-

tions, avoiding any potentially dangerous

situation for the user and others. The machine

operator should:

• Avoid to operate the machine on unbalanced

surfaces;

• Remember that the high pressure water jet

causes a recoil effect on the pistol. The recoil

values are indicated in the technical specifica-

tions table;

• Use protective clothing.

• Wear protective goggles and rubber slip-

proof boots

• Avoid dispersing substances that are pollut-

ing, toxic or harmful in any way.

 ATTENTION: Risk of explosion. Do not spray

flammable liquids.

The high pressure water jet may be dangerous if used incorrectly. Never direct the jet at per-

sons and/or animals, electrical appliances or the machine itself. Do not use the machine when

persons and/or animal are within the range of its high pressure jet.

Do not direct the jet against yourself or other persons to clean clothes or shoes.

NO

13

This machine has been built in conformity

with current safety regulations. Use of electric

appliances requires the observations of a few

simple rules:

Do not touch electric parts when the machine

is on.

Inspection, maintenance and repairs should be

carried out by qualified personnel. In any case

unplug the machine before performing any of

the above operations.

Do not pull the cord to disconnect the power

supply and do not pull on the hose to move the

machine.

ATTENTION: high pressure flexible hoses,

high pressure connectors, safety devices,

electrical connections and spray guns are

important for the safety of the device.

Do not start the unit if the power cord is

damaged. Apply to qualified personnel for its

replacement. Replacement cords should have

the same technical specifications as the origi-

nal cord. Do not carry out repairs on the elec-

trical cord and avoid cord damage.

Do not start the unit if the high pressure hose, connectors and the gun are damaged. By

replacement make sure that the new components have at least the same rating as the original

components.The technical specifications of the hose should be printed on the hose itself (max

pressure, production date, manufacturer).

NO

14

Avoid covering the machine during use and

use the machine in a well ventilated area.

When the machine is off insert the safety

device on the gun to avoid accidental opening.

The unit is equipped with a thermal protec-

tor which trips and electrically disconnects the

motor when it overheats.

If this event occurs, turn the selection knob on

the unit to the "0" position (machine OFF).

Read carefully the troubleshooting guide befo-

re starting the unit again.

To ensure the security of the machine, use only original spare parts and accessories supplied

by the manufacturer.

THE MANUFACTURER CANNOT BE HELD RESPONSABLE FOR ANY DAM-

AGE CAUSED BY DISRESPECTING THE DESIGNATED USES OF THIS

MACHINE, IT'S INSTRUCTIONS AND WARNINGS INDICATED IN THIS

BOOKLET.

NO

Do not leave the machine running for more

than 5 minutes with the gun closed. After this

time period the water temperature within the

machine increase and may cause damage to

the machine.

15

7 - HOW TO USE CHEMICAL PRODUCTS

The unit can suck and mix detergents and other liquid chemicals thanks

to an automatic device incorporated in the unit itself, which is remote

controlled by operating the ROTOTEK.

- The unit is equipped with a chemical suction kit (Fig. A).

- Fit the brass connector into the chemical control knob and filter into chemical container

(Fig.B).

- Select low pressure with the ROTOTEK (Fig. C).

- At this point the suction and mixing of the chemical will start automatically.

- You can regulate the quantity of chemicals by adjusting the chemical control knob (Fig. D).

- When you wish to stop using chemicals in order to clean on rinse, simply release the gun

trigger and adjust the ROTOTEK to high pressure.

At this point the chemical injection automatically stops.

If you foresee not using the unit for a long period of time, we suggest to clean the chemical

suction kit with clear water to avoid chemical deposit build-up.

Attention! In the event of direct contact with detergent additives, follow instructions provided

by the manufacturer and/or product retailer and rinse the affected body part with clean water.

8 - USE OF ROTOTEK OR MULTIREG 99

Pressure selection must be carried out with closed gun (1)

A - selection of the pressure

• High pressure (2)

• Low pressure (3)

B - selection of the jet

• straight pin jet (4)

• fan jet (5)

OFF

2

1

3

HL

4

5

HL

AB

16

9 - PRECAUTIONS AGAINST FREEZING AND INSTRUCTIONS FOR STORAGE

10 - MAINTENANCE

• Maintenance and repairs should always be performed by trained and authorised personnel.

• Before carrying out any cleaning, maintenance and/or parts replacement, disconnect the

machine from the power mains, removing the plug from the power outlet.

• Proper maintenance favours a longer duration of operation and improved performance.

• Periodically check the conditions of the washer, pressurised parts (pipe, fittings, lance) and

the electrical cable (see "General warnings for use").

Check for any water or oil leaks and/or malfunctions.

If necessary, replace affected parts.

The list of specific machine components and circuit diagrams are contained in this booklet.

Contact Interpump Group customer service in the event of any doubts.

If the unit is to be stored in a place where there is risk of freezing, or it is to remain unused for

more than three months, we recommend placing some anti-freeze solution into the pump, (a

normal anti-freeze as used in your vehicle is sufficient).

If in doubt at low temperatures or any long length of storage time, we suggest you turn the

motor with the key provided before starting, to release any possibilities of blockages from free-

zing or a build up of lime scale deposits.

Taking these precautions before starting will avoid damage to the unit.

Remember to remove the key before switching on.

17

• Check oil level periodically.

• Oil must be changed after the first 20 hours of operation of the machine. Subsequent oil

changes must be carried out every 150 hours of machine operation.

• In any case it is advisable to change the oil at least once a year.

• Used oil must be collected in containers and disposed of in special centres according to

current standards. It absolutely should not be discarded into the environment.

• Oil type: SAE 15W40 Mineral.

• Oil capacity: 0,33 liter.

10.1 - OIL CHANGE

10.3 - REPLACEMENT OF HIGH PRESSURE NOZZLE

Periodically it is necessary to replace the high pressure nozzle as this is a component subject

to normal wear during use. This wear can generally be noticed by a decrease of the working

pressure. Contact your dealer if you wish to purchase a new nozzle.

10.2 - INLET FILTER

Before using the machine it is IMPORTANT to make sure that the filter is clean. Wash the filter

under a water tap or blow it with air to remove completely all dirt particles.

Remember that a well-cleaned filter means good performance and long life for your machine.

Blow the filter with air.

Remove filter from water inlet. Wash the filter under a water

tap.

11 - DISPOSAL OF THE MACHINE

• In case of no further use of the machine, it is advisable to disconnect the power cord mak-

ing the machine inoperative.

• Keep out of reach of children.

• This machine is considered "special waste", disassemble and gather homogeneous parts for

recycling.

• Do not used recycled parts as spare parts.

IInnffoorrmmaattiioonn oonn tthhee ddiissppoossaall ooff eelleeccttrriicc aanndd eelleeccttrroonniicc

eeqquuiippmmeenntt iinn ccoommpplliiaannccee wwiitthh ddiirreeccttiivvee 22000022//9966 CCEE

((RRAAEEEE))..

11.. WWiitthhiinn tthhee EEuurrooppeeaann UUnniioonn

Warning: do not use the normal house trash bin to dispose of this

product.

Used electric and electronic equipment must be handled separately

and in compliance with the regulations relating to the treatment,

recovery and recycling of the said products.

In accordance with the regulations applied in the member States, pri-

vate users resident in the EU can take used electric and electronic

equipment free of charge to designated collection centers*. In some

countries * the local dealer, too, can withdraw the old product free of

charge if the user purchases a new, similar product.

* For more information contact your local campetent authorities.

If you experience difficulties in locating an authorized disposal center,

consult the dealer from whom you purchased the product.

The correct disposal of this product will contribute to ensure that the waste is submitted to the

required treatment, recovery and recycling, preventing the potential negative impact on envi-

ronment and human health, which could be caused by an unsuitable disposal of the waste.

The national regulations provide sanctions against whoever unlawfully disposes of or abandons

waste of electric or electronic equipment.

22.. IInn ccoouunnttrriieess oouuttssiiddee tthhee EEuurrooppeeaann UUnniioonn..

If you wish to dispose of this product, contact your local authorities to get information about the

correct disposal method.

Warning: the product

is marked with this

symbol, which means

that electric and elec-

tronic products should

not be disposed of

with the normal

house-hold waste. A

separate collection

system is foreseen for

these products.

18

La page est en cours de chargement...

Interpump BOXJET TURBO 8.70 Operating Instructions Manual

Ce manuel convient également à

Interpump BOXJET TURBO 8.70 Operating Instructions Manual

dans d''autres langues

Autres documents