Wacker Neuson RD16-90 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Operator’s Manual
Notice d'emploi
Ride-On Roller
Rouleau
RD12
RD12A
RD16
Type RD12, RD12A, RD16
Document 5200022670
Date
1117
Version 09
Language EN-FR
5200022670
Copyright notice
© Copyright 2017 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operators Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
RD 12 / 12A / 16 Foreword
wc_tx003836gb_FM10.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing any of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number
RD 16 5000620060, 5000620402
5000620798, 5000620799
RD 16 IRH 5000620127
RD 12 5000620059, 5000620321
RD 12A 5000620058, 5100013933
5000620320, 5000620369
wc_gr010237
Serial Number:
Foreword RD 12 / 12A / 16
4 wc_tx003836gb_FM10.fm
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Engine exhaust, some of its constituents, and certain vehicle components contain
or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Manufacturers
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
2016-CE-RD16_en_FM10.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051 USA
Product
Product
Product category
Product function
Item number
Net installed power
Measured sound power level
Guaranteed sound power level
RD16-90, RD16 IRH-90, RD16-100
Ride-On Roller
To compact asphalt
5000620799, 5000620127, 5000620798
16.8 kW
104 dB(A)
106 dB(A)
Conformity Assessment Procedure
According to 2000/14/EC ANNEX VIII
Notified Body
Lloyds Register Verification Limited (Notified Body No 0038)
71 Fenchurch Street, London EC3M 4BS, United Kingdom
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2000/14/EC, 2014/30/EU, EN 500-1, EN 500-4
Authorized Person for Technical Documents
Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6, 85084
Reichertshofen, Germany
Menomonee Falls, WI, USA, 01.06.16
Original Declaration of Conformity
Keith Herr
Vice President and Managing Director
For Wacker Neuson
Paul Sina
Manager, Product Engineering
For Wacker Neuson
Jeff Volden
Director, Product Engineering
For Wacker Neuson
Keith Herr
Vice President and Managing Director
For Wacker Neuson
wc_bo5200022654_09TOC.fm 7
Table of ContentsRD 12 / 12A / 16
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 13
1.1 Signal Words Used in this Manual ..................................................... 13
1.2 Machine Description and Intended Use ............................................. 14
1.3 Safety Guidelines for Operating the Machine ..................................... 15
1.4 Operating the Machine in Electrical Storms ....................................... 17
1.5 Service Safety .................................................................................... 18
1.6 Operator Safety while Using Internal Combustion Engines ............... 20
1.7 Hydraulic Fluid Safety ........................................................................ 21
1.8 Safety Guidelines for Lifting and Transporting the Machine ............... 21
2 Labels—RD 16 22
2.1 Label Locations .................................................................................. 22
2.2 Label Meanings .................................................................................. 23
3 Labels—RD 12, RD 12A 32
3.1 Label Locations .................................................................................. 32
3.2 Label Meanings .................................................................................. 33
4 Lifting and Transporting 39
4.1 Locking and Unlocking the Articulated Joint ....................................... 39
4.2 Lifting the Machine ............................................................................. 40
4.3 Tying Down and Transporting the Machine ........................................ 42
4.4 Towing the Machine ........................................................................... 43
4.5 Manually Releasing the Parking Brake .............................................. 44
4.6 Towing Bypass Valve ......................................................................... 46
5 Controls — RD 16 48
5.1 Features and Controls ........................................................................ 48
5.2 Control Panel and Indicator Lights ..................................................... 50
5.3 Auxiliary Battery Positive Terminal ..................................................... 53
8 wc_bo5200022654_09TOC.fm
Table of Contents RD 12 / 12A / 16
6 RD 12 and RD 12A Controls 54
6.1 Features and Controls .........................................................................54
6.2 Control Panel and Indicator Lights ......................................................56
6.3 Auxiliary Battery Positive Terminal ......................................................57
7 Operation 58
7.1 Preparing the Machine for First Use ....................................................58
7.2 Position of the Operator ......................................................................58
7.3 Mounting and Dismounting the Machine .............................................58
7.4 Fire Extinguisher Requirement ............................................................59
7.5 Roll Over Protection Structure (ROPS) ...............................................60
7.6 Rotating Beacon (if equipped) .............................................................62
7.7 Operator Presence System .................................................................63
7.8 Recommended Fuel—Diesel ..............................................................64
7.9 Recommended Fuel—Gasoline ..........................................................64
7.10 Refueling the Machine .........................................................................65
7.11 Positioning the Scrapers .....................................................................66
7.12 Using the Seat Belt ..............................................................................67
7.13 Using the Forward / Reverse Lever .....................................................68
7.14 Using the Vibration System .................................................................69
7.15 Using the Water Spray System ...........................................................70
7.16 Using the Backup Alarm ......................................................................71
7.17 Using the Parking Brakes—RD 16 ......................................................72
7.18 Using the Manual Parking Brake—RD 12 / 12A ..................................73
7.19 Parking Brake Adjustment — RD 12 / 12A ..........................................74
7.20 Avoiding the Danger Zone ...................................................................75
7.21 Adding Ballast to Rear Drum — RD 12 / 12A only ..............................76
7.22 Preliminary Checks .............................................................................77
7.23 Starting, Operating, and Stopping the Machine—RD 16 .....................78
7.24 Emergency Shut-down Procedure (RD 16) .........................................81
7.25 Starting, Operating, and Stopping the Machine—RD 12 / 12A ...........82
7.26 Emergency Shutdown Procedure (RD 12 / 12A) .................................85
7.27 Machine Stability .................................................................................86
7.28 Operating on Slopes ............................................................................87
7.29 Anti-Vandalism Protection and Machine Access .................................88
8 General Maintenance 90
8.1 Maintaining the Emission Control System ...........................................90
8.2 Periodic Maintenance Schedule ..........................................................91
8.3 Rear Frame Access .............................................................................92
wc_bo5200022654_09TOC.fm 9
Table of ContentsRD 12 / 12A / 16
8.4 Safety-Related Spare Parts ................................................................ 94
8.5 Maintaining the Seat and Seat Belt .................................................. 100
8.6 Hydraulic Oil Level ........................................................................... 101
8.7 Checking the Water Filter ................................................................. 102
8.8 Cleaning the Water Filter .................................................................. 103
8.9 Grease Fittings—RD 16 ................................................................... 104
8.10 Grease Fittings—RD 12 / 12A .......................................................... 105
8.11 Battery .............................................................................................. 106
8.12 Hydraulic System Cleanliness .......................................................... 107
8.13 Hydraulic Oil Requirements .............................................................. 107
8.14 Checking and Cleaning the Hydraulic Tank Breather ...................... 108
8.15 Changing the Hydraulic Oil and Filter ............................................... 109
8.16 Bleeding the Hydraulic System ........................................................ 110
8.17 Checking the Neutral Switch ............................................................ 111
8.18 Inspecting the Seat Belt ................................................................... 112
8.19 Cleaning the Spray Bars .................................................................. 113
8.20 Testing the Brake System ................................................................ 114
8.21 Long-Term Storage .......................................................................... 115
8.22 Machine Disposal and Decommissioning ......................................... 116
9 Engine Maintenance: Kohler (T4f) 117
10 Engine Maintenance—Wacker Neuson/Robin 122
11 Engine Maintenance—Honda GX630 124
12 Troubleshooting 126
13 Technical Data—RD 16 128
13.1 Engine .............................................................................................. 128
13.2 Roller ................................................................................................ 129
13.3 Lubrication ........................................................................................ 129
13.4 Hydraulic Pressures ......................................................................... 130
13.5 Sound Measurements ...................................................................... 130
13.6 Measurements of Operator Exposure to Vibration ........................... 131
13.7 Dimensions ....................................................................................... 132
10 wc_bo5200022654_09TOC.fm
Table of Contents RD 12 / 12A / 16
14 Technical Data—RD12 133
14.1 Engine ...............................................................................................133
14.2 Roller .................................................................................................134
14.3 Lubrication .........................................................................................134
14.4 Hydraulic Pressures ..........................................................................135
14.5 Sound Measurements .......................................................................135
14.6 Measurements of Operator Exposure to Vibration ............................135
14.7 Dimensions ........................................................................................136
15 Technical Data—RD 12A 137
15.1 Engine ...............................................................................................137
15.2 Roller .................................................................................................138
15.3 Lubrication .........................................................................................138
15.4 Hydraulic Pressures ..........................................................................139
15.5 Sound Measurements .......................................................................139
15.6 Measurements of Operator Exposure to Vibration ............................139
15.7 Dimensions ........................................................................................140
16 Emission Control Systems Information
and Warranty—Gasoline 141
16.1 Emission Control System Background Information ...........................141
16.2 Limited Defect Warranty for Exhaust Emission Control System .......142
16.3 Limited Defect Warranty for Wacker Neuson
Evaporative Emission Control Systems ............................................142
17 Emission Control Systems Information
and Warranty—Diesel 145
17.1 Emission Control System Background Information ...........................145
17.2 Limited Defect Warranty for Exhaust Emission Control System .......146
17.3 Limited Defect Warranty for Wacker Neuson
Emission Control Systems ................................................................146
18 AEM Safety Manual 149
wc_bo5200022654_09TOC.fm 11
Table of ContentsRD 12 / 12A / 16
19 Schematics—RD 16 171
19.1 Electrical Schematic—Complete ...................................................... 172
19.2 Electrical Schematic Components .................................................... 173
19.3 Electrical Schematic Section A ......................................................... 174
19.4 Electrical Schematic Components .................................................... 175
19.5 Electrical Schematic Section B ......................................................... 176
19.6 Electrical Schematic Components .................................................... 177
19.7 Electrical Schematic Section C ........................................................ 178
19.8 Electrical Schematic Components .................................................... 179
19.9 Electrical Schematic Section D ........................................................ 180
19.10 Electrical Schematic Components .................................................... 181
19.11 Electrical Schematic—Complete RD 16IRH ................................... 182
19.12 Electrical Schematic Components RD 16IRH ................................ 183
19.13 Electrical Schematic Section A RD 16IRH ..................................... 184
19.14 Electrical Schematic Components RD 16IRH ................................ 185
19.15 Electrical Schematic Section B RD 16IRH ..................................... 186
19.16 Electrical Schematic Components RD 16IRH ................................ 187
19.17 Electrical Schematic Section C RD 16IRH ..................................... 188
19.18 Electrical Schematic Components RD 16IRH ................................ 189
19.19 Electrical Schematic Section D RD 16IRH ..................................... 190
19.20 Electrical Schematic Components RD 16IRH ................................ 191
19.21 Hydraulic Schematic ......................................................................... 192
19.22 Hydraulic Schematic Components ................................................... 193
20 Schematics—RD 12 194
20.1 Hydraulic Schematic ......................................................................... 194
20.2 Hydraulic Schematic Components ................................................... 195
20.3 Electrical Schematic ......................................................................... 196
20.4 Electrical Schematic Components .................................................... 197
21 Schematics—RD 12A 198
21.1 Electrical Schematic ......................................................................... 198
21.2 Electrical Schematic Components .................................................... 199
21.3 Hydraulic Schematic ......................................................................... 200
21.4 Hydraulic Schematic Components ................................................... 201
12 wc_bo5200022654_09TOC.fm
Table of Contents RD 12 / 12A / 16
wc_si000897gb_FM10.fm
13
RD 12 / 12A / 16 Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety mes-
sages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000897gb_FM10.fm
14
Safety Information RD 12 / 12A / 16
1.2 Machine Description and Intended Use
This machine is a dual drum, ride-on roller. The Wacker Neuson Ride-On Roller
consists of an articulated frame onto which is mounted a gasoline or diesel engine,
a fuel tank, a hydraulic tank, a water tank, a hydrostatic drive system, two steel
drums containing internal eccentric weights, and an operator’s platform with a
ROPS (Roll Over Protective Structure). The engine powers the hydraulic systems
that provide machine movement and drum vibration. The vibrating drums smooth
and compact the work surface as the machine moves. Machine speed, direction,
and vibration are controlled by the operator from the operator’s seat on the
platform.
The machine is designed as a lightweight roller to be used in the compaction of
sublayers and finish layers of asphalt on roads, driveways, parking lots, and other
types of asphalt-covered surfaces.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to tow other machines
Using the machine to spray liquids other than water (i.e., diesel fuel on asphalt)
Operating the machine outside of factory specifications.
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual.
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Burns from hot hydraulic fluid
Fire hazards from improper refueling techniques
Fuel and its fumes
Personal injury from improper lifting techniques
Crushing hazards from improper operation (feet, legs, or arms extending
outside of the operator work station) and for other persons in the work zone
Line of sight blockage by the ROPS
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_si000897gb_FM10.fm
15
RD 12 / 12A / 16 Safety Information
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Remain aware of changing surface conditions and use extra care when
operating over uneven ground, on hills, or over soft or coarse material. The
machine could shift or slide unexpectedly.
Use caution when operating the machine near the edges of pits, trenches or
platforms. Check to be sure that ground surface is stable enough to support the
weight of the machine with operator and that there is no danger of the roller
sliding, falling or tipping.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Keep the area around the muffler free of debris such as leaves, paper, cartons,
etc. A hot muffler could ignite the debris and start a fire.
wc_si000897gb_FM10.fm
16
Safety Information RD 12 / 12A / 16
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
Safe
operating
practices
When operating this machine do:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts
Always remain seated and wear the seat belt at all times while operating the
machine.
Keep clear of the articulated steering joint between the front and rear frames.
Always disengage and stow the locking bar for the articulated steering joint
before operating the machine. The machine cannot be steered when the locking
bar is engaged.
When operating this machine:
Do not operate a machine in need of repair.
Do not drive over curbs or other uneven objects that will result in the machine
and operator being shaken.
Do not attempt to start the machine when standing alongside it. Only start the
engine when seated in the driver's seat and with the forward/reverse control in
the neutral position.
Do not leave the machine running unattended.
Do not use a cellphone or send text messages while operating this machine.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
wc_si000897gb_FM10.fm
17
RD 12 / 12A / 16 Safety Information
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
1.4 Operating the Machine in Electrical Storms
Reducing risk
of injury
If lightning strikes occur in the vicinity of the work area, there are two methods of
reducing risk of injury:
1. If you are on the ground:
Stay away from the machine.
Do not attempt to climb onto the machine or into the operator’s seat.
2. If you are in the operator’s seat:
Remain in the operator’s seat.
Do not attempt to climb off the machine.
WARNING
Operating this machine in an electrical storm can be hazardous. You can be injured
or killed by lightning.
Be aware of deteriorating weather conditions and approaching electrical storms.
Stop work and get to a safe shelter before lightning strikes occur.
wc_si000897gb_FM10.fm
18
Safety Information RD 12 / 12A / 16
1.5 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Re-install the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
When servicing or maintaining the machine:
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
wc_si000897gb_FM10.fm
19
RD 12 / 12A / 16 Safety Information
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair
Remove all jewelry (including rings)
wc_si000897gb_FM10.fm
20
Safety Information RD 12 / 12A / 16
1.6 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Re-install the fuel tank cap after refueling.
Use suitable tools for refueling (for example, a fuel hose or funnel).
When refueling the engine:
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398

Wacker Neuson RD16-90 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues