Winmate R15ID3S-67A3HB Guide de démarrage rapide

Marque: Winmate

Modèle: R15ID3S-67A3HB

Taper: Guide de démarrage rapide

Ce manuel convient également à

Please read these instructions carefully before using this product, and save this manual for future use.

15” G-WIN

Rugged Panel PC

Full IP67

Model No. R15IK3S-67C3(HB)

R15IH3S-67A3(HB)

R15IB3S-67A3(HB)

R15ID3S-67A3(HB

Quick Start Guide

Document Version 1.1

Document Part No. 9152111I102C

15" G-WIN Rugged Panel PC Quick Start Guide

Contents

Chapter 1: Introduction 5

1.1 Features 5

1.2 Package Contents 5

1.3 Description of Parts 6

1.4 Physical Buttons and LED Indicators 7

Chapter 2: Getting Started 9

2.1 Turning On and Off Your Device 9

2.2 How to Enable Watchdog 11

Chapter 3: Mounting 12

3.1 VESA Mount 12

3.2 Dash/ Yoke Mount 13

Chapter 4: Installation 15

4.1 Safety Information 15

4.2 Wiring Requirements 15

4.3 Connecting to Other Devices 16

4.4 Connector Description 17

4.4.1 Power Input Connector 17

4.4.2 Ethernet Connector 18

4.4.3 Serial Interface Connector 19

4.4.4 USB 2.0 Connector 20

Appendix 21

Appendix A: Specifications 21

Appendix B: Cleaning the Monitor 23

Appendix C: Winmate Software Development Kit 23

Chapter 1: Introduction

FCC Statement

This device complies with part 15 FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received

including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a class "B" digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference

at him own expense.

European Union

Electromagnetic Compatibility Directive (2014/30/EU)

 EN55024: 2010/ A1: 2015

o IEC61000-4-2: 2009

o IEC61000-4-3: 2006+A1: 2007+A2: 2010

o IEC61000-4-4: 2012

o IEC61000-4-5: 2014

o IEC61000-4-6: 2014

o IEC61000-4-8: 2010

o IEC61000-4-11: 2004

 EN55032: 2012/AC:2013

 EN61000-3-2:2014

 EN61000-3-3:2013

Low Voltage Directive (2014/35/EU)

 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

This equipment is in conformity with the requirement of the following EU legislations and

harmonized standards. Product also complies with the Council directions.

15" G-WIN Rugged Panel PC Quick Start Guide

No part of this document may be reproduced, copied, translated, or transmitted in any form or

by any means, electronic or mechanical, for any purpose, without the prior written permission of

the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product, including

circuits and/or software described or contained in this manual in order to improve design and/or

performance. We assume no responsibility or liability for the use of the described product(s)

conveys no license or title under any patent, copyright, or masks work rights to these products,

and make no representations or warranties that these products are free from patent, copyright,

or mask work right infringement, unless otherwise specified. Applications that are described in

this manual are for illustration purposes only. We make no representation or guarantee that

such application will be suitable for the specified use without further testing or modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from material and

workmanship defects for a period of one year from the invoice date. If the customer discovers a

defect, we will, at his/her option, repair or replace the defective product at no charge to the

customer, provide it is returned during the warranty period of one year, with transportation

charges prepaid. The returned product must be properly packaged in its original packaging to

obtain warranty service. If the serial number and the product shipping data differ by over 30

days, the in-warranty service will be made according to the shipping date. In the serial numbers

the third and fourth two digits give the year of manufacture, and the fifth digit means the month

(e. g., with A for October, B for November and C for December).

For example, the serial number 1W18Axxxxxxxx means October of year 2018.

Customer Service

We provide a service guide for any problem by the following steps: First, visit the website of our

distributor to find the update information about the product. Second, contact with your

distributor, sales representative, or our customer service center for technical support if you need

additional assistance.

You may need the following information ready before you call:

 Product serial number

 Software (OS, version, application software, etc.)

 Description of complete problem

 The exact wording of any error messages

In addition, free technical support is available from our engineers every business day. We are

always ready to give advice on application requirements or specific information on the

installation and operation of any of our products.

Chapter 1: Introduction

Congratulations on purchasing Winmate® 15-inch G-WIN Rugged Panel PC with full IP67

waterproof rating. Panel PC features 15” panel with sunlight readable screen, fanless cooling

system, low power consumption, WLAN integration, shock and vibration resistant. The robust

design fits the demands for every harsh environment applications such as logistics,

transportation/ fleet management, heavy vehicles, utility and also outdoor usage.

1.1 Features

Winmate® 15” G-WIN Rugged Panel PC features:

 15" high quality LCD panel, 1024 x 768 resolution, 400 nits

 IP67 dust and water proof design (with VESA mount installation)

 Aluminum die-casting housing with anti-corrosion treatments

 Build-in ambient light sensor

 Wide range 9 to 36V DC input with isolation

 5 wire resistive touch/ anti-reflective protection glass (optional)

1.2 Package Contents

Carefully remove the box and unpack your device. Please check if all the items listed below are

inside your package. If any of these items are missing or damaged contact us immediately.

Standard factory shipment list:

 Panel PC

 Quick Start Guide

 Driver CD

Varies by product specifications

Part No. 9152111I102C

Varies by product specifications

 Power Cable

 Serial Interface Cable

 LAN Cable

Part No. 94J003L020K1

Part No. 94G0103090Q0

Part No. 94I0080080KF

 USB Cable

 Mounting Bracket (Optional)

Part No. 9480108080Q0

Part No. 99KK15A00001

15" G-WIN Rugged Panel PC Quick Start Guide

1.3 Description of Parts

Unit: mm

Dimensions: 398 x 308 x 58

№

Description

①

LAN (M12 Type)

②

USB (M12 Type)

③

RS232 (M12 Type)

④

9-36V DC (M12 Type)

⑤

OSD Control Panel

Chapter 1: Introduction

1.4 Physical Buttons and LED Indicators

Physical buttons and LED indicators (OSD Control Panel) are located on the rear side of the

panel PC.

15" G-WIN Rugged Panel PC Quick Start Guide

Physical Buttons

Icon

Button

Function

Power

Turn ON or turn OFF the panel PC.

Reset

Clear any pending errors or events and brings a system

to normal condition or an initial state.

Lock / Unlock

Tap this button to lock / unlock the function of OSD panel.

Auto Dimming/

Manually

Tap the button once to AUTOMATICALLY adjust

brightness mode.

Press the button again to MANUALLY adjust brightness

mode.

Day/ Night Mode

Tap this button to enter DAY MODE.

Tap this button to enter NIGHT MODE to increase

visibility in low-light conditions.

Brightness UP

Increase the brightness of the display screen, or allows

user to navigate items of a single OSD menu.

Brightness DOWN

Decrease the brightness of the display screen, or allows

user to navigate items of a single OSD menu.

LED Adjustment

Adjust the brightness of the LED.

LED Indicators

Indicator

Color

Definition

PWR

Green

Power is ON and the device functions normally.

Orange

Panel PC is suspended.

HDD

Green

HDD is active.

OFF

HDD is inactive.

Chapter 2: Getting Started

2.1 Turning On and Off Your Device

To turn on you’re your device:

1. Remove the protective cap of the power connector.

2. Connect power cable to the connector of your device. Make sure the cable fits to the

connector, then tighten the O-ring (by turning clockwise) to secure the connection.

3. The device will boot automatically when powered on.

15" G-WIN Rugged Panel PC Quick Start Guide

To shut down your device:

1. Select the Start button ( ) and then select Power > Shut down.

2. Disconnect the power cord from the Panel PC to completely turn off the device.

To forcibly shut down your device, press and hold for three to five seconds the power button

located on the front OSD control panel.

IMPORTANT:

During forced shut down unsaved data may be lost.

Chapter 2: Getting Started

2.2 How to Enable Watchdog

To enable Watchdog, download Winmate Watchdog utility. Find more information about

Watchdog in “Watchdog Guide” that you can download from Winmate Download Center.

To enable watchdog in Watchdog AP follow the instructions below:

1. On the right bottom side of the desktop screen, click triangle button to show hidden

icons.

2. lick icon to open Watchdog utility.

3. Open Watchdog utility to set countdown time and periodically feed time, or disable

watchdog.

Example:

Every 10 min watchdog will monitor the system, in

case any error occurs the system will restart

automatically when the countdown time reaches 0.

Every 9 min watchdog timer will be reset to 10 min.

Setting

Description

Watchdog Countdown Time

The system automaticity restarts when this countdown time

reaches zero. Default: 10 min

Periodically Feed Time

To set a cycle time to automatically reset watchdog timer.

Default: 9 min

Enable / Disable

Enable or disable watchdog. Default: Enable

15" G-WIN Rugged Panel PC Quick Start Guide

Chapter 3: Mounting

3.1 VESA Mount

This device supports VESA Mounting and provides various types of mounting options to fit any

industrial use or vehicle.

Size

VESA Plate

15”

100x100 mm

Mounting Instruction

Use Philips M4x5 screws to fix the desk stand to VESA holes on the back cover of the device.

*The picture is for demonstration purposes only. VESA Mounting accessories are not supplied

by Winmate.

Chapter 3: Mounting

3.2 Dash/ Yoke Mount

You can purchase mounting bracket from Winmate as an optional accessory.

Part Number: 99KK15A00001

Mounting instruction:

1. Place the Panel PC on the bracket stand, aiming screw hole for each other.

2. Secure three M5x10 screws to fix the device upon the bracket stand.

3. Secure tightly locking handle to the Panel PC.

15" G-WIN Rugged Panel PC Quick Start Guide

4. Loosen the hand-screw adjustment tool, then you can adjust product angle on the stand.

Then screw the product tightly again to secure the stand position.

Desk Stand Dimensions

Chapter 4: Installation

4.1 Safety Information

WARNING! / AVERTISSEMENT!

Always completely disconnect the power cord from your chassis whenever you

work with the hardware. Do not make connections while the power is on.

Sensitive electronic components can be damaged by sudden power surges.

Only experienced electronics personnel should open the PC chassis.

Toujours débrancher le cordon d’alimentation du chassis lorsque vous travaillez

sur celui-ci. Ne pas brancher de connections lorsque l’alimentation est présente.

Des composantes électroniques sensibles peuvent être endommagées par des

sauts d’alimentation. Seulement du personnel expérimenté devrait ouvrir ces

chassis.

CAUTION/ATTENTION

Always ground yourself to remove any static charge before touching the CPU

card. Modern electronic devices are very sensitive to static electric charges. As

a safety precaution, use a grounding wrist strap at all times. Place all electronic

components in a static-dissipative surface or static-shielded bag when they are

not in the chassis.

Toujours verifier votre mise à la terre afin d’éliminer toute charge statique avant

de toucher la carte CPU. Les équipements électroniques moderns sont très

sensibles aux décharges d’électricité statique. Toujours utiliser un bracelet de

mise à la terre comme précaution. Placer toutes les composantes

électroniques sur une surface conçue pour dissiper les charge, ou dans un sac

anti-statique lorsqu’elles ne sont pas dans le chassis.

4.2 Wiring Requirements

The following common safety precautions should be observed before installing any electronic

device:

 Strive to use separate, non-intersecting paths to route power and networking wires. If

power wiring and device wiring paths must cross make sure the wires are perpendicular

at the intersection point.

 Keep the wires separated according to interface. The rule of thumb is that wiring that

shares similar electrical characteristics may be bundled together.

 Do not bundle input wiring with output wiring. Keep them separate.

 When necessary, it is strongly advised that you label wiring to all devices in the system.

 Do not run signal or communication wiring and power wiring in the same conduit. To

avoid interference, wires with different signal characteristics (i.e., different interfaces)

should be routed separately.

 Be sure to disconnect the power cord before installing and/or wiring your device.

 Verify the maximum possible current for each wire gauge, especially for the power

cords. Observe all electrical codes dictating the maximum current allowable for each

wire gauge.

 If the current goes above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

 Be careful when handling the unit. When the unit is plugged in, the internal components

generate a lot of heat which may leave the outer casing too hot to touch.

15" G-WIN Rugged Panel PC Quick Start Guide

4.3 Connecting to Other Devices

This Panel PC comes with various interfaces located on the bottom panel. All of these connectors

have been shipped with protective caps. To ensure the waterproof function can work properly,

make sure that the protective caps and have been securely tightened whenever the connectors

are not used.

IMPORTANT

Please note that when reinstalling the protective cap, it must be fully tightened to ensure the unit is

properly sealed to meet the IP67 enclosure rating.

Chapter 4: Installation

4.4 Connector Description

The panel PC features M12 type waterproof connectors covered with protective caps.

4.4.1 Power Input Connector

Panel PC has M12 type 3 pin male power input connector which accepts 9-36 V DC power input.

Use waterproof power cable to connect the Panel PC to the source of power.

DC Power Cable

15" G-WIN Rugged Panel PC Quick Start Guide

4.4.2 Ethernet Connector

Panel PC has M12 type Ethernet connector. Use waterproof LAN cable to connect the panel PC

to the Ethernet.

LAN Cable

Chapter 4: Installation

4.4.3 Serial Interface Connector

Panel PC has M12 type 10 pin male RS-232 connector. Use waterproof serial cable to connect

the panel PC to external devices.

COM Cable

15" G-WIN Rugged Panel PC Quick Start Guide

4.4.4 USB 2.0 Connector

Panel PC has M12 12 pin male USB connector. Use waterproof USB 2.0 cable to connect the

panel PC to external devices.

USB Cable

La page charge ...

Winmate R15ID3S-67A3HB Guide de démarrage rapide

Marque: Winmate

Modèle: R15ID3S-67A3HB

Taper: Guide de démarrage rapide

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Winmate R15ID3S-67A3HB Quick start guide

Documents connexes

Autres documents

SYNAPSE EMB-S2-FW Controller Manuel utilisateur