ICOM IC-F3200DEX Manuel utilisateur

INSTRUCTION MANUAL

The photo shows the

VHF transceiver.

VHF DIGITAL/ANALOG TRANSCEIVER

iF3200DEX

Series

UHF DIGITAL/ANALOG TRANSCEIVER

iF4200DEX

Series

This device complies with Part 15 of the FCC Rules. Op-

eration is subject to the condition that this device does not

cause harmful interference.

i

FOREWORD

READ ALL INSTRUCTIONS carefully and completely before

using the transceiver.

SAVE THIS INSTRUCTION MANUAL— This instruc-

tion manual contains important operating instructions for the IC-

F3203DEX VHF DIGITAL/ANALOG TRANSCEIVER and the IC-

F4203DEX UHF DIGITAL/ANALOG TRANSCEIVER

• This instruction manual includes some functions which are us-

able only when they are preset by your dealer. Ask your dealer

for details.

• To use in explosive atmospheres, read the leaﬂet “SAFETY

MANUAL” comes with the transceiver.

EXPLICIT DEFINITIONS

WORD DEFINITION

RDANGER!

Personal death, serious injury or an explosion

may occur.

RWARNING!

Personal injury, ﬁre hazard or electric shock

may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk of

personal injury, ﬁre or electric shock.

ii

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo-

rated (Japan) in Japan, the United States, the United Kingdom, Germany, France,

Spain, Russia and/or other countries.

IDAS is trademark of Icom Incorporated (Japan).

dPMR and the dPMR logo are trademarks of the dPMR MoU Association.

All other products or brands are registered trademarks or trademarks of their re-

spective holders.

VOICE CODING TECHNOLOGY

The AMBE+2™ voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This

voice coding Technology is licensed solely for use within this Com-

munications Equipment. The user of this Technology is explicitly

prohibited from attempting to extract, remove, decompile, reverse

engineer, or disassemble the Object Code, or in any other way

convert the Object Code into a human-readable form. U.S. Patent

Nos.

#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365,

#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,

#5,247,579, #5,226,084 and #5,195,166.

iii

PRECAUTIONS

R DANGER! NEVER short the terminals of the battery pack.

R DANGER! Use and charge only speciﬁed Icom battery packs

with Icom radios or Icom chargers. Only Icom battery packs are

tested and approved for use with Icom radios or charged with Icom

chargers. Using third-party or counterfeit battery packs or chargers

may cause smoke, ﬁre, or cause the battery to burst.

R WARNING! NEVER hold the transceiver so that the antenna

is very close to, or touching exposed parts of the body, especially

the face or eyes, while transmitting. The transceiver will perform

best if the microphone is 5 to 10 cm (2 to 4 inches) away from the

lips and the transceiver is vertical.

R WARNING! NEVER operate the transceiver with a headset

or other audio accessories at high volume levels. Hearing experts

advise against continuous high volume operation. If you experience

a ringing in your ears, reduce the volume level or discontinue use.

R WARNING! NEVER operate the transceiver while driving a

vehicle. Safe driving requires your full attention—anything less may

result in an accident.

CAUTION: MAKE SURE the ﬂexible antenna and battery pack

are securely attached to the transceiver, and that the antenna and

battery pack are dry before attachment. Exposing the inside of the

transceiver to water will result in serious damage to the transceiver.

DO NOT operate the transceiver near unshielded electrical blast-

ing caps.

iv

PRECAUTIONS

DO NOT push [PTT] when you do not actually intend to transmit.

DO NOT use or place the transceiver in direct sunlight or in areas

with temperatures below–20°C (–4°F) or above +55°C (+131°F).

DO NOT modify the transceiver. The speciﬁcations may change

and then not comply with the requirements of a corresponded

regulation. The transceiver warranty does not cover any problems

caused by unauthorized modiﬁcation.

DO NOT use harsh solvents such as benzine or alcohol when

cleaning, as they will damage the transceiver surfaces.

BE CAREFUL! The transceiver will become hot when operating

it continuously for long periods of time.

BE CAREFUL! The transceiver meets IP67 requirements for

dust-tight and waterproof protection.

However, once the transceiver has been dropped, dust-tight and

waterproof protection cannot be guaranteed because of possible

damage to the transceiver’s case or the waterproof seal.

Even when the transceiver power is OFF, a slight current still ﬂows

in the circuits. Remove the battery pack or batteries from the trans-

ceiver when not using it for a long time. Otherwise, the installed

battery pack or batteries will become exhausted, and will need to

be recharged or replaced.

MAKE SURE to turn the transceiver power OFF before connect-

ing the supplied/optional equipment.

v

TABLE OF CONTENTS

FOREWORD ..................................................................................i

EXPLICIT DEFINITIONS ................................................................i

VOICE CODING TECHNOLOGY ..................................................ii

PRECAUTIONS ............................................................................ iii

TABLE OF CONTENTS .................................................................v

1 ACCESSORIES ....................................................................1–4

Supplied accessories ■ ............................................................1

Accessory attachments ■ ........................................................1

2 PANEL DESCRIPTION ......................................................5–13

Front, top and side panels ■ ....................................................5

LED indicator ■ ........................................................................7

Programmable function keys ■ ..............................................10

3 BASIC OPERATION .........................................................14–26

Turning ON the power ■ .........................................................14

Channel selection ■ ...............................................................15

Call procedure ■ ....................................................................16

Receiving and transmitting ■ .................................................17

Setting the microphone gain ■ ...............................................20

Setting the squelch level ■ .....................................................21

Setting the Beep level ■ .........................................................22

Setting the Ringer level ■ .......................................................23

Output power level selection ■ ...............................................24

Priority A channel selection ■ ................................................24

Lone Worker Emergency Call ■ .............................................25

Man Down Emergency Call ■ ................................................25

Emergency Call ■ ..................................................................26

vi

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

TABLE OF CONTENTS

4 dPMR OPERATION .........................................................27–32

dPMR operation ■ ..................................................................27

Receiving a call ■ ..................................................................27

Transmitting a call ■ ...............................................................30

Status message transmission ■ .............................................32

Scrambler function ■ ..............................................................32

5 BATTERY CHARGING .....................................................33–38

Caution ■ ...............................................................................33

Battery charger ■ ...................................................................37

6 SPEAKER MICROPHONE ...............................................39–40

Optional HM-203EX description ■ .........................................39

To attach ■ .............................................................................40

7 OPTIONS ..........................................................................41–42

8 SAFETY TRAINING INFORMATION ...............................43–46

9 FCC INFORMATION ..............................................................47

Accessory attachments ■

Flexible antenna D

Connect the ﬂexible antenna to the antenna connector.

CAUTION:

• NEVER carry the transceiver by

holding only the antenna.

• DO NOT connect the antenna other

than listed on page 42.

• Transmitting without an antenna

may damage the transceiver.

Supplied accessories ■

The following accessories are supplied with the transceiver.

1

ACCESSORIES

Battery pack*

Belt clip*

Connector cover

(with screws)

Battery charger* AC adapter*

* Not supplied, or the shape is different, depending on the version.

Flexible antenna

(This illustration is for the VHF type.)

2

1

ACCESSORIES

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Belt clip D

To attach the belt clip:

➥ Slide the belt clip in the direction of the arrow until the belt clip

locks in place, and makes a ‘click’ sound.

Belt clip

To detach the belt clip:

Remove the battery pack from the transceiver, if it is attached. q

(p. 3)

Lift the tab up ( w q), and slide the belt clip in the direction of the

arrow (w).

w

q

Ta b

3

1

ACCESSORIES

Battery pack D

To attach the battery pack:

Slide the battery pack on the back of the transceiver in the direction of

the arrow (q), then lock it with the battery release button.

• Slide the battery pack until the battery release button makes a ‘click’

sound.

To remove the battery pack:

Push the battery release button in the direction of the arrow (w) as

shown below. The battery pack can be removed.

NEVER remove or attach the battery pack when the transceiver

is wet or soiled. This may result water or dust getting into the

transceiver and/or battery pack and may result in them being

damaged.

q

w

Battery release

button

NOTE: Keep the battery pack terminals clean. It’s a good idea to

occasionally clean them.

4

1

ACCESSORIES

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Connector cover D

Attach the connector cover when optional equipment is not used.

To attach the connector cover:

Attach the cover to the multi q

connector.

Tighten the screw. w

To detach the connector cover:

q Remove the screw with a

phillips screwdriver.

w Detach the cover to connect

the optional equipment.

w

q

w

5

2

PANEL DESCRIPTION

Front, top and side panels ■

Microphone

Speaker

r

w

e

q

y

LOWER KEY

u

UPPER KEY

t

PTT SWITCH

i

ANTENNA

CONNECTOR

ROTARY

SELECTOR

LED INDICATOR

VOLUME

CONTROL

MULTI

CONNECTOR

q ROTARY SELECTOR

Rotate to select the preprogrammed memory channels or scan

lists, depending on the preprogramming.

w VOLUME CONTROL [VOL]

Rotate to turn the power ON or OFF, and adjust the audio level.

6

2

PANEL DESCRIPTION

e LED INDICATOR (pp. 7–9)

Lights red while transmitting. ➥

Lights green while receiving a signal, or when the squelch ➥

is open.

Lights/blinks orange when the matched 2/5-tone code is re- ➥

ceived, depending on the presetting.

r MULTI CONNECTOR

Connect optional equipment.

t PTT SWITCH [PTT]

 Hold down to transmit; release to receive.

y LOWER KEY [Lower]

u UPPER KEY [Upper]

A desired function can be assigned by your dealer. (p. 10)

i ANTENNA CONNECTOR

Connect the antenna.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Connector cover

NOTE: Attach the cover

when optional equipment

is not used. (p. 4)

7

2

PANEL DESCRIPTION

LED indicator ■

The LED indicator indicates the status of various

parameters of the transceiver as follows;

(Reference: R=Red, G=Green, O=Orange)

• TX:

Lights Red while transmitting.

R

• RX busy:

On an analog channel, lights Green when in the noise squelch

opens. On a digital or mixed channel, lights Green while detecting

a frame synchronization.

G

• Call LED:

Turns ON when receiving a matched 2/5-tone, or receiving a Sta-

tus or SDM (Short Data Message) call.

O

• Call LED:

Blinks when receiving a matched 2/5-tone, or receiving a Status

or SDM call.

O O

• Call LED:

Blinks while waiting for a return signal.

O O O

• Success:

Blinks slowly when your call was successful.

O G

8

2

PANEL DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

• Call error:

Blinks slowly when your call failed, or was refused.

O R

• Audible:

Blinks slowly after a return signal is received when in the Audible

mode*.

* Mute is released. (Received signal will be heard.)

O

• Fast/Slow scan or voting:

Blinks when scanning for a channel to search for a signal or a

repeater to register on.

G G

• Low Battery 1:

You should charge the battery soon. (blinks slowly)

G G

• Low Battery 2:

You must charge the battery. (blinks fast)

G G G G

• TX low Battery 1:

Low Battery was detected in the TX mode.

R R

• TX low Battery 2:

Very Low Battery was detected

in the

TX mode.

R R R R

9

2

PANEL DESCRIPTION

• Channel Error:

Blinks when a non-programmed channel is selected.

R O R O R O R O R O R O R O R O

• Power ON:

Blinks at transceiver startup.

R O GR O G

• TX inhibit:

Blinks while in the TX inhibit mode such as when the TOT or Lock-

out function is activated.

R O O O

• Emergency:

Blinks when an Emergency call was received.

G O R G O R G O R G O R

• Emergency Locator Ringer Siren:

Blinks while the Emergency locator, Ringer or Siren is activated.

G O R G O R G O R G O R

LED indicator (Continued) ■

10

2

PANEL DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Programmable function keys ■

The following functions can be assigned to the [Upper] and [Lower]

programmable function keys.

Consult your Icom dealer or system operator for details concerning

your transceiver’s programming.

SCAN

Push to start and cancel scanning.

• When the scan started with the Power ON Scan or Auto Scan func-

tion, push to pause the scan. The paused scan resumes after the

speciﬁed time period has passed.

PRIORITY A CHANNEL, PRIORITY B CHANNEL

Push to select the Priority A or Priority B channel.

PRIORITY A CHANNEL (REWRITE),

PRIORITY B CHANNEL (REWRITE)

Push to select the Priority A or Priority B channel. ➥

Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1 second ➥

to assign the operating channel to the Priority A or Priority B

channel, respectively.

MEMORY CHANNELS 1, 2, 3, 4

Push to directly select memory channel 1, 2, 3 or 4, if programmed.

Consult your dealer for details.

LONE WORKER (p. 25)

Hold down for 1 second to turn ON the Lone Worker function. ➥

• When the Lone Worker function is turned ON, and no operation is

performed for the speciﬁed time period, the Emergency function is

automatically turned ON.

Push to turn OFF the Lone Worker function. ➥

11

2

PANEL DESCRIPTION

Programmed function keys (Continued) ■

MONITOR, MONITOR (AUDIBLE)

Push to turn the CTCSS (DTCS) or 2/5-tone squelch Mute ON ➥

or OFF.

• Only during LMR operation, push to open any squelch func-

tions, or deactivate any mute functions.

• Only during PMR operation, push to activate one or two of the

following functions* on each channel.

- Hold down to unmute the channel (Audible mode).

- Push to mute the channel (Inaudible mode).

- Push to send a ‘reset code’ after the communication is ﬁnished.

*Ask your dealer for details.

NOTE: The unmute condition may automatically return to the

mute condition, after a speciﬁed time period.

➥

Depending on the presetting, holding down this key for 1

second cancels a scan.

LOCK

Hold down to electronically lock all programmable keys except

[Moni(Audi)], [Call] (including Call A and Call B), [Emergency], Sur-

veillance] and [Lone Worker].

HIGH/LOW (p. 24)

Select the transmit output power level temporarily or permanently,

depending on the presetting.

• Ask your dealer for the output power level for each selection.

TALK AROUND

Hold down for 1 second to turn ON the Talk Around function. ➥

• The Talk Around function equalizes the transmit frequency to the

receive frequency for transceiver-to-transceiver communication.

Push to turn OFF the Talk Around function. ➥

DTMF AUTODIAL

Push to transmit a programmed DTMF code.

12

2

PANEL DESCRIPTION

RE-DIAL

Push to transmit the last-transmitted DTMF code.

NOTE: TX memories are cleared after turning OFF the transceiver.

WIDE/NARROW

Push to toggle the IF bandwidth between Wide, Mid* or Narrow.

* Depending on the presetting, the Mid channel width may not be

selectable. Ask your dealer for details.

CALL, CALL A, CALL B

Push to transmit a 2/5-tone code.

• Tone call transmission may be necessary before you call another sta-

tion, depending on your signalling system.

• [Call A] and/or [Call B] keys may be selectable when your system

employs selective ‘Individual/Group’ calls. Ask your dealer which call

is assigned to each key.

EMERGENCY

Hold down for speciﬁed time period to transmit an emergency call.

• The emergency call transmits with beeps, and the LED lights red.

• The transceiver can transmit an emergency call without the beep

sounding and the LED indicator lighting. Ask your dealer for details.

• If you want to cancel the emergency call, hold down the key again

before transmitting the call.

• The emergency call is transmitted one time only, or repeatedly until re-

ceiving an acknowledgement signal, or until the power is turned OFF.

When a matched 5-tone code signal is received, the emergency func-

tion can be cancelled, depending on the presetting. (PMR operation

only)

SURVEILLANCE

Hold down for 1 second to turn ON the Surveillance function. ➥

• When this function is turned ON, the beep is not heard and the LED

does not light when a signal is received, or a key is pushed.

Push to turn OFF the Surveillance function. ➥

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Programmed function keys (Continued) ■

SIREN

Hold down for 1 second to emit a siren sound.

This function can be used for situations other than an emergency

alert, such as a security alarm for example.

The transceiver emits the siren sound until the power is turned

OFF.

SCRAMBLER

Hold down for 1 second to turn ON the Voice Scrambler function ➥

while operating in the digital mode.

Push to turn OFF the Voice Scrambler function. ➥

ANNOUNCE

Push to turn the Channel Announce function ON or OFF.

• When this function is turned ON, the transceiver announces the posi-

tion of [ROTARY SELECTOR] between 1 and 16 when rotating [RO-

TARY SELECTOR] to a desired number.

13

2

PANEL DESCRIPTION

La page est en cours de chargement...

ICOM IC-F3200DEX Manuel utilisateur

Ce manuel convient également à

ICOM IC-F3200DEX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents