Sauder Barrister Lane Storage Credenza 414721 Manuel utilisateur

PLEASE CONTACT US

BEFORE RETURNING

YOUR UNIT TO THE STORE

1-800-523-3987

www.sauder.com

Made in the USA

Archbold, OH

NOTE: THIS INSTRUCTION BOOKLET CONTAINS

IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Lot #: 350044 04 / 05 / 13

Date Purchased: ____________________

English .................... Page 1-22

Français ...............Pages 23-25

Espanol .............Páginas 26-28

414721

Storage Credenza

Barrister Lane Collection

ASSEMBLY TOOLS REQUIRED

Hammer

No. 2 Phillips Screwdriver

Tip Shown Actual Size

ADULT ASSEMBLY REQUIRED

TABLE OF CONTENTS

Part Identiﬁ cation .......................3

Hardware Identiﬁ cation .............4

Assembly Steps ....................5-22

Français ..............................23-25

Espanol ...............................26-28

Safety .................................29-30

Warranty ...................................31

Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury

or death. A TV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.

• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!

• This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.

• The size of the television, front-to-back and side-to-side, must ﬁ t within the space deﬁ ned in the diagram.

• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)

• Never allow the sides of the TV to extend past the side edges of the TV support surface.

• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.

• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.

WARNING

19"

70"

135 lbs.

Page 2 www.sauder.com/services 414721

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked

letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help

identify similar parts.

A END 2

B UPRIGHT 1

C TOP 1

D BOTTOM 1

E BACK 2

F CENTER BACK 1

G LARGE BACK 2

H DOOR 2

I INNER DOOR 2

J ADJUSTABLE SHELF 2

K RIGHT BASE 1

L LEFT BASE 1

M BASE 1

N FRONT MOLDING 1

O RIGHT MOLDING 1

P LEFT MOLDING 1

Q END MOLDING 2

R UPRIGHT MOLDING 1

S SHELF MOLDING 2

T BRACE 2

Page 3

www.sauder.com/services414721

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

A

E

G

H

I

J

Q

S

T

HARDWARE IDENTIFICATION

Screws are shown actual size. You may receive extra hardware with your unit.

Page 4 www.sauder.com/services 414721

WARNING

Never use this furniture with a TV that is too

large or too heavy. Severe injury or death

can occur. The TV and furniture will be

unstable and may tip.

-The TV must less than 135 lbs.

-The base of the TV must be able to sit

completely on this shelf.

-Refer to instruction book for complete safety

information.

Note: This is a permanent label. Do not try

to remove. Surface will be damaged.

02/ 02 2 6 9 2 3 2 269232

WARNING LABEL - 1

4L

(Refer to the last step for proper location and application)

3M

ANTI-SKID PAD - 1

FOOT - 1

23E

27H

HINGE - 8

BLACK 9/16" LARGE HEAD SCREW - 93

1S

METAL BRACKET - 6

4G

NAIL - 16

1N

METAL PIN - 14

1R

RUBBER SLEEVE - 8

2R

CAM SCREW - 12

8F

HIDDEN CAM - 24

1F

BLACK 1-7/8" FLAT HEAD SCREW - 6

2S

SAFETY BRACKET - 1

1G

SMALL MAGNETIC

CATCH - 2

2I

STRIKE PLATE - 4

6I

BLACK 1/2" FLAT HEAD SCREW - 4

11S

SILVER 1-1/2" MACHINE SCREW - 2

95S

BLACK 9/16" PAN HEAD SCREW - 4

51S

MAGNETIC CATCH - 2

12I

SILVER 5/8" MACHINE SCREW - 4

15S

TWIST-LOCK

®

FASTENER - 2

10F

CAM COVER - 14

13P

CAM DOWEL - 12

2F

33M

DECORATIVE

END - 4

34M

DECORATIVE

BACKPLATE - 2

69K

DECORATIVE

KNOB - 2

39M

DECORATIVE

POST - 4

CORNER BRACKET - 4

31G

Look for this icon. It means a video

assembly tip is available at:

www.sauder.com/services/tips

1

S

t

e

p

Assemble your unit on a carpeted ﬂ oor or on the empty carton to avoid scratching your unit or the ﬂ oor.

To begin assembly, push a SAUDER TWIST-LOCK

®

FASTENER (10F) into the large holes in the MOLDINGS (O and P).

Page 5

www.sauder.com/services414721

Do not tighten the TWIST-LOCK® FASTENERS in this step.

10F

O

P

2

S

t

e

p

Page 6 www.sauder.com/services 414721

Push twenty-four HIDDEN CAMS (1F) into the ENDS (A), UPRIGHT (B), BOTTOM (D), and BRACES (T). Then, insert the metal

end of a CAM DOWEL (2F) into each HIDDEN CAM, except the short edges of the ENDS (A) and BRACES (T).

Do not tighten the HIDDEN CAMS in this step.

Arrow

(12 used)

(24 used)

Arrow

1F

2F

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

A

B

D

T

Do not insert CAM

DOWELS into these edges.

Do not insert CAM

DOWELS into these edges.

Do not insert CAM

DOWELS into these parts.

3

S

t

e

p

Page 7

www.sauder.com/services414721

Turn twelve CAM SCREWS (8F) into the BASES (K and L) and MOLDINGS (N, O, and P).

8F

K

L

N

O

P

(12 used)

Fasten the END MOLDINGS (Q) to the ENDS (A). Tighten four HIDDEN CAMS.

Fasten the BASES (K and L) to the ENDS (A). Tighten four HIDDEN CAMS.

4

S

t

e

p

Page 8 www.sauder.com/services 414721

Caution

Risk of damage or

injury. Hidden Cams

must be completely

tightened. Hidden

Cams that are not

completely tightened

may loosen, and parts

may separate.

To completely tighten:

Start Tighten

Arrow

Maximum

210 degrees

Minimum

190 degrees

A

Q

K

L

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

These holes

must be here.

Angled edge

This END (A) will now be

called the LEFT END (A).

This END (A) will now be

called the RIGHT END (A).

Fasten the MOLDINGS (O and P) to the TOP (C). Tighten two TWIST-LOCK

®

FASTENERS.

5

S

t

e

p

Page 9

www.sauder.com/services414721

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must remain

fully inserted in the hole of the adjoining part while

locking the FASTENER.

2. Tighten the FASTENER with a Phillips screwdriver

as tight as possible.

Dowel end

C

P

O

Surface with holes

Long ﬁ nished edge

6

S

t

e

p

Page 10 www.sauder.com/services 414721

Fasten two CORNER BRACKETS (31G) to the MOLDINGS (O and P) and TOP (C). Use eight BLACK 9/16" LARGE HEAD

SCREWS (1S).

Fasten two METAL BRACKETS (4G) to the TOP (C). Use two BLACK 9/16" LARGE HEAD SCREWS (1S).

Fasten the FRONT MOLDING (N) to the TOP (C) and MOLDINGS (O and P). Use six BLACK 9/16" LARGE HEAD

SCREWS (1S) through the METAL BRACKETS (4G) and CORNER BRACKETS (31G) and into the FRONT MOLDING.

C

P

O

N

BLACK 9/16" LARGE HEAD SCREW

(16 used for the BRACKETS)

1S

4G

31G

Fasten the BRACES (T) to the FRONT MOLDING (N). Tighten four HIDDEN CAMS.

Push a SMALL MAGNETIC CATCH (2I) into the center hole in each BRACE (T).

Fasten a MAGNETIC CATCH (12I) to each BRACE (T). Use four BLACK 9/16" PAN HEAD SCREWS (51S).

NOTE: Pay close attention to the positioning of the MAGNETIC CATCHES (12I). Follow the diagram.

7

S

t

e

p

Page 11

www.sauder.com/services414721

12I

N

BLACK 9/16" PAN HEAD SCREW

(4 used for the MAGNETIC CATCHES)

51S

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

T

2I

8

S

t

e

p

Page 12 www.sauder.com/services 414721

C

B

Fasten the UPRIGHT (B) to the TOP (C). Tighten two HIDDEN CAMS.

Fasten the UPRIGHT (B) to the FRONT MOLDING (N). Use a METAL BRACKET (4G) and two BLACK 9/16" LARGE HEAD

SCREWS (1S).

Fasten the UPRIGHT MOLDING (R) to the UPRIGHT (B). Tighten two HIDDEN CAMS.

Maximum

210 degrees

Minimum

190 degrees

Arrow

Surface with

HIDDEN CAMS

R

N

BLACK 9/16" LARGE HEAD SCREW

(2 used for the METAL BRACKETS)

1S

4G

Fasten the LEFT END (A) to the LEFT MOLDING (P). Tighten two HIDDEN CAMS.

Insert two METAL PINS (1R) into the CENTER BACK (F).

Insert the METAL PINS (1R) in the CENTER BACK (F) into the holes in the TOP (C).

9

S

t

e

p

Page 13

www.sauder.com/services414721

C

A

L

P

F

Surface with

HIDDEN CAMS

Surface

with

holes

1R

Q

10

S

t

e

p

Page 14 www.sauder.com/services 414721

A

L

F

B

D

Fasten the BOTTOM (D) to the LEFT BASE (L). Tighten two HIDDEN CAMS.

Fasten the BOTTOM (D) to the UPRIGHT (B) and CENTER BACK (F). Use three BLACK 1-7/8" FLAT HEAD SCREWS (2S).

Maximum

210 degrees

Minimum

190 degrees

Arrow

BLACK 1-7/8" FLAT HEAD SCREW

(3 used in this step)

2S

Surface with

HIDDEN CAMS

These small holes

must be here.

11

S

t

e

p

Page 15

www.sauder.com/services414721

E

BLACK 1-7/8" FLAT HEAD SCREW

(2 used in this step)

2S

D

Surface

with

holes

Surface

with

holes

Insert four METAL PINS (1R) into the TOP (C).

Insert the METAL PINS (1R) in the TOP (C) into the holes in the BACKS (E).

Fasten the BACKS (E) to the BOTTOM (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).

1R

C

1R

Finished edge

Fasten the RIGHT END (A) to the RIGHT MOLDING (O) and BOTTOM (D) to the RIGHT BASE (K). Tighten four HIDDEN

CAMS.

12

S

t

e

p

Page 16 www.sauder.com/services 414721

Maximum

210 degrees

Minimum

190 degrees

Arrow

D

A

O

Surface without

HIDDEN CAMS

Q

K

13

S

t

e

p

Page 17

www.sauder.com/services414721

Fasten two CORNER BRACKETS (31G) to the BASES (K and L) and BOTTOM (D). Use eight BLACK 9/16" LARGE HEAD

SCREWS (1S).

Fasten three METAL BRACKETS (4G) to the BOTTOM (D). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).

NOTE: Be sure the BRACKETS are even with the edge of the BOTTOM.

Fasten the BASE (M) to the BOTTOM (D) and BASES (K and L). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S) through

the METAL BRACKETS (4G) and CORNER BRACKETS (31G) and into the BASE.

BLACK 9/16" LARGE HEAD SCREW

(18 used for the BRACKETS)

1S

D

K

L

M

31G

4G

D

14

S

t

e

p

Page 18 www.sauder.com/services 414721

G

F

E

BLACK 9/16" LARGE HEAD SCREW

(24 used in this step)

1S

Carefully turn your unit over onto its front edges. Lay the LARGE BACKS (G) over your unit.

Fasten the LARGE BACKS (G) to the BACKS (E and F). Use twenty-four BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten

the top and bottom edges of the LARGE BACKS to your unit using the NAILS (1N).

NOTE: Position perforations as shown. Perforations have been provided for access through the BACK. Carefully cut out the holes

needed.

Push the FOOT (23E) into the hole in the BOTTOM (D).

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

NAIL

(16 used in this step)

1N

Unﬁ nished

surface

Unﬁ nished

surface

23E

D

The perforations

should be here.

The perforations

should be here.

15

S

t

e

p

Page 19

www.sauder.com/services414721

Fasten two HINGES (27H) to each DOOR (H and I). Use sixteen BLACK 9/16" LARGE HEAD SCREWS (1S).

NOTE: The HINGES should be positioned exactly as shown.

BLACK 9/16" LARGE HEAD SCREW

(16 used in this step)

1S

27H

H

I

16

S

t

e

p

Page 20 www.sauder.com/services 414721

IMPORTANT: You may need someone's help in this step.

Carefully stand your unit upright.

Fasten the DOORS (H and I) to the MOLDINGS (Q and R). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S).

Fasten the DECORATIVE ENDS (33M) to the DOOR (H). Use two SILVER 5/8" MACHINE SCREWS (15S).

Insert a DECORATIVE POST (39M) into the DECORATIVE ENDS.

Fasten the DECORATIVE BACKPLATE (34M) and DECORATIVE KNOB (69K) to the DOOR (H). Use a SILVER 1-1/2"

MACHINE SCREW (95S).

Fasten a STRIKE PLATE (6I) to each DOOR (H and I). Use two BLACK 1/2" FLAT HEAD SCREWS (11S).

Repeat this step for the other DOORS (H and I). Fasten DOOR (I) to the MOLDING (R) and fasten DOOR (H) to the other

MOLDING (Q).

BLACK 9/16" LARGE HEAD SCREW

(16 used for the HINGES)

1S

SILVER 1-1/2"" MACHINE SCREW

(2 used for the BACKPLATE and KNOB)

95S

H

I

Q

SILVER 5/8" MACHINE SCREW

(4 used for the DECORATIVE ENDS)

15S

39M

69K

BLACK 1/2" FLAT HEAD SCREW

(4 used for the STRIKE PLATES)

11S

39M

33M

6I

R

34M

Q

La page est en cours de chargement...

Sauder Barrister Lane Storage Credenza 414721 Manuel utilisateur

Sauder Barrister Lane Storage Credenza 414721 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents