Broilmaster SSG-36 Le manuel du propriétaire

Marque: Broilmaster

Modèle: SSG-36

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

SSG-36-1

R-3848 Page 1

AVERTISSEMENT

S'il y a une odeur de gaz:

1. Coupez l'admission de gaz de l'appareil.

2. Éteindre toute flamme nue.

3. Ouvrir le couvercle.

4. Si l'odeur persiste, appeler immédiatement

votre compagnie de gaz ou votre département

des incendies.

OUTDOOR

COOKING APPLIANCE

SSG-36-1

EFFECTIVE DATE

APRIL, 2003

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call your

supplier or your fire department.

WARNING: If not installed, operated and

maintained in accordance with the manu-

facturer's instructions, this product could

expose you to substances in fuel or from fuel

combustion which can cause death or seri-

ous illness.

FOR YOUR SAFETY

1. Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

2. An LP cylinder not connected for use shall

not be stored in the vicinity of this or any

other appliance.

AVERTISSEMENT: Si l’installation, l’usage

et l'entretien de ce produit ne sont pas faits

selon les instructions du fabricant, ce produit

peut vous exposer à des matières contenues

dans le carburant ou provenant de la

combustion du carburant lesquelles peuvent

causer la mort ou de sérieuses maladies.

AVERTISSEMENT

1. Ne pas entreposer ni utiliser de l'essence ni

d'autres vapeurs ou liquides inflammables

dans le voisinage de l'appareil, ni de tout

autre appareil.

2. Une bouteille de propane que n'est pas

recordée en vue de son utilisation, ne doit pas

être entreposée dans le voisinage de cet

appareil ou de tout autre appareil.

GRILL SHOWN WITH OPTIONAL SCG-36 CART

The Superb SeriesThe Superb Series

The Superb Series

Downloaded from www.Manualslib.com manuals search engine

Page 2 R-3848

• Read instructions before lighting.

• Open lid during lighting.

• If ignition does not immediately take place, turn the burner valve

handles to OFF, wait 5 minutes, and repeat the lighting procedure.

• Minimum clearance from sides and back of unit to adjacent combus-

tible construction below top of unit, 6 inches from sides and 12 inches

from back.

• Minimum horizontal clearance from sides and back of unit to adjacent

vertical combustible construction extending above top of unit, 6 inches

from sides and 12 inches from back.

• Do not locate this outdoor cooking gas appliance under overhead

unprotected combustible surfaces.

• WARNING: Electrical Grounding Instructions

This outdoor cooking gas appliance is equipped with a three-prong

(grounding) plug for your protection against shock hazard and should

be plugged directly into a properly grounded three-prong receptacle.

Do not cut or remove the grounding prong from this plug.

• Keep any electrical supply cord and the fuel supply hose away from

any heated surfaces.

• DO NOT put anything around the outdoor cooking appliance that will

obstruct the flow of combustion and ventilation air.

• DO keep the outdoor cooking gas appliance area clear and free from

combustible material, gasoline and other flammable vapors and liq-

uids.

• Do make visual check of burner flames. Clean and replace damaged

parts.

• This outdoor cooking gas appliance is not intended to be installed in or

on recreational vehicles and/or boats.

• This outdoor cooking gas appliance shall be used only outdoors and

shall not be used in a building, garage or any other enclosed area.

For Outdoor Use Only.

If Stored Indoors,

Detach and Leave Cylinder Outdoors.

• Lire les instructions avant d'allumer l'appareil.

• Ouvrir le couvercle avant d'allumer l'appareil.

• Si l'appareil ne s'allume pas immédiatement, fermer le

robinet du brûleur, attendre 5 minutes puis procéder de

nouveau à l'allumage.

• Dégagement minimal à respecter entre les côtes et l'arrière

de l'appareil et une construction combustible adjacente

située au-dessous de la partie supérieure de l'appareil, soit 6

pouces des côtés et 12 pouces de l'arrière.

• Dégagement horizontal minimal à respecter entre les côtés

et l'arrière de l'appareil et une construction combustible

verticale adjacent dépassant la partie supérieure de

l'appareil, soit 6 pouces des côtés et 12 pouces de l'arrière.

• Il est interdit d'installer le présent appareil au-dessous des

surfaces combustibles non protégées.

• AVERTISSEMENT: Instruction Pour la Mise à la Terre

Électrique

Cet appareil est muni d'une fiche à trois broches (mise à la

terre) afin de vous protéger des chocs et doit être branché

directement dans une prise de courant à trois broches

adéquatement mise à la terre. Il ne faut pas couper ou

enlever la broche de mise à la terre de cette fiche.

Pour Utilisation à l'Extérieur Seulement.

Si l'Appareil est Entre posé à l'Intérieur,

Enlever les Bouteilles et les Laisser à l'Extérieur.

CUSTOMER WARNING:

• Know the odor of LP Gas. If you hear, see or smell leaking LP gas,

immediately get everyone away from the cylinder and call the Fire

Department. Do not attempt repairs.

• LP Gas is heavier than air and may settle in low places while

dissipating.

• Contact with the liquid contents of cylinder will cause freeze burns to

the skin.

• Do not allow children to tamper or play with cylinder.

• When not connected for use, keep cylinder valve turned off. Self

contained outdoor cooking appliances shall be limited to a cylinder of

20 lb. capacity or less.

• Do not use, store or transport cylinder where it would be exposed to

high temperatures. Relief valve may open allowing a large amount of

flammable gas to escape.

• When transporting, keep cylinder secured in an upright position with

cylinder valve turned off.

• CAUTION: The gas pressure regulator provided with this outdoor

cooking gas appliance must be used. This regulator is set for an outlet

pressure of 11 inches water column. (The outlet pressure specified by

the manufacturer.)

• The gas supply must be turned off at the LP gas supply cylinder when

this outdoor cooking gas appliance is not in use.

• The LP gas supply cylinder must be disconnected when this outdoor

cooking gas appliance is not in use.

AVERTISSEMENT:

• Savoir reconnaître l'odeur du GPL. Si vous entendez un sifflement

ou si vous sentez une fuite de GPL, demander immédiatement à

toutes les personnes présentes de s'éloigner de la boutielle et appeler

le service d'incendie. Ne pas essayer de la réparer.

• Le GPL étant plus lourd que l'air, il peut s'accumuler près du sol

avant de se dissiper.

• Tout contact de la peau avec la phase liquide de la bouteille causera

des brûlures par le froid.

• Empêcher les enfants de manipuler la bouteille ou de jouer avec.

• Lorsque la bouteille n'est pas raccordée à l'appareil, en maintenir

fermé le robinet. Pour les appareils de cuisson autonomes d'extérieur,

utiliser une bouteille d'une capacité maximale de 9 kg (20 lb.).

• Ne pas utiliser, entreposer ou transporter la bouteille en l'exposant à

une température excessive car la soupape de sûreté risque de s'ouvrir

et de laisser échapper une grande quantité de gaz inflammable.

• Pour transporter une bouteille de GPL, la maintenir solidement fixée

en position verticale avec le robinet fermé.

• MISE EN GARDE: Le régulateur de pression de gaz prévu avec

cet appareil de cuisson à gaz pour l'extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 11 pouces de

colonne d'eau (la pression de sortie spécifiée par le manufacturier.

• L'alimentation du gaz doit être fermée à la bouteille de gaz de

pétrole liquéfié, lorsque cet appareil de cuisson extérieur n'est

pas utilisé.

• La bouteille d'alimentation en gaz de pétrole liquéfié doit être

débranché lorsque cet appareil de cuisson extérieur n'est pas

utilisé.

PROPANE (LP) GAS WARNINGS

IMPORTANT WARNINGS

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 3

4. The use of the propane from the cylinder allows the OPD to reset

itself for the next fill.

5. Connects to all standard or quick-connect couplings.

6. The Overfill Protection Device affects incoming liquid propane

flow only. Does not affect normal propane gas discharge when

properly connected to the appliance regulator.

7. All propane cylinders should be filled by qualified professionals

only.

Purging

1. Due to the decreased Btu delivery, purging may take longer.

2. To increase the speed of purging, open the outage valve during

release.

3. Reminder: Each new cylinder must be purged before filling.

4. For purging instructions, refer to NPGA 133-89(a).

Btu Delivery

The OPD valve has a size 56 orifice through which the propane is

released for consumption. Depending on the propane's temperature and

pressure, the release from the cylinder is approximately 125,000 Btu/

hour.

OVERFILL PROTECTION DEVICE (OPD) ON 20 LB. PROPANE

CYLINDER

Attention: Consumer be advised, this gas grill must be connected

to an LP gas cylinder incorporating an OPD.

The OPD will help reduce the potential for the overfilling of the propane

cylinder, thus reducing the possibility of hydrostatic relief valve dis-

charges.

Overfill Protection Device Valve Function

1. As the cylinder is filled, the rising level of liquid propane lifts the

float to the stop position to prevent dangerous overfilling.

Does not affect the filling process or use of the cylinder.

2. At a safe filling level, the float cam triggers the pin to fall into the

recess of the cam, sealing this path off and preventing any more

liquid propane from flowing through the lower valve body into the

cylinder.

3. The propane builds up pressure in the chamber (center spring) and

pushes the piston up to form a seal, effectively stopping the filling

process.

WARNING: Inspect the fuel supply hose before each use of

the outdoor cooking gas appliance. The hose can be ac-

cessed by opening the front door on the outdoor cooking gas

appliance. If it is evident there is excessive abrasion or

wear, or the hose is cut, it must be replaced prior to the

outdoor cooking gas appliance being put into operation.

Contact Empire Comfort Systems, Inc. to obtain a replace-

ment fuel supply hose. Keep the ventilation opening(s) of

the cylinder enclosure free and clear from debris.

WARNING: Do not store a second 20 lb. propane cylinder

within the utility cart. The utility cart is designed for the use

and storage of one 20 lb. propane cylinder.

• LP-gas supply cylinder to be used must be constructed and marked

in accordance with the specifications for LP-gas cylinders of the

U.S. Department of Transportation (DOT) or the National Standard

of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for the

Transportation of Dangerous Goods.

If the outdoor cooking gas appliance is not in use, the gas must be

turned off at the supply cylinder.

• Storage of an outdoor cooking gas appliance indoors is permissible

only if the cylinder is disconnected and removed from the outdoor

cooking gas appliance.

Cylinders must be stored outdoors out of the reach of children and

must not be stored in a building, garage or any enclosed area.

• The pressure regulator and hose assembly supplied with the out-

door cooking gas appliance must be used. A replacement pressure

regulator and hose assembly for this outdoor cooking gas appliance

can be obtained by contacting Empire Comfort Systems, Inc.

LP GAS CYLINDER INFORMATION

Specifications

Model SSG-36

Input BTU/HR (KW/H) Max. Min.

5 Main Burners 12,000/Burner 5,000

1 Side Burner 30,000 5,000

2 Rotisserie Burners 12,000/Burner

Height (grill only) 27 1/8"

Width 55 1/4"

Depth 31"

Gas Inlet 1/2"

General Information

This appliance is design certified in accordance with American National

Standards Institute Z21.58b-2002 and CGA-1.6b-2002 by the Canadian

Standards Association as an outdoor cooking gas appliance to be

installed according to these instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not shown

on the rating plate is the responsibility of the person and

company making the change.

SPECIFICATIONS

Important

All correspondence should refer to complete Model number, Serial

number and type of gas.

Accessories

SCG-36 Stainless Steel Cart

GHK-12 Quick Disconnect 12 ft. Hose LP & Nat.

TKS-36 Stainless Steel Cooking Utensils

SGD-36 Stainless Steel Door for Built-in

GSS-36 Stainless Steel Side Shelf for Left or Right

GIJ-36 Stainless Steel Liner for Built-in

SUW-15 15" Stainless Steel Wok

VCC-36 Vinyl Cover for Grill on Cart

VCB-36 Vinyl Cover for Grill Built-in

SSP-1 Steamer Pan with Lid (1 Small & 1 Large)

Initial Operation

Before cooking food on your grill for the first time, operate the (5) main

burners at 500°F for 30 minutes. The high temperature will remove any

residues from the new components.

Downloaded from www.Manualslib.com manuals search engine

Page 4 R-3848

IMPORTANT INFORMATION ABOUT YOUR NEW TYPE-1

GRILL CONNECTION

Read all grill and related product literature before connecting or using

your grill, and please read the following information completely before

attempting to connect your grill to a propane cylinder.

Keep these instructions in a safe place. You may need to refer to them

when connecting other cylinders after filling.

Your new grill regulator is equipped with a coupling nut . Do not attempt

to connect any propane cylinder not equipped with a mating Type-1

cylinder valve.

Figure 1

Connecting the Regulator to the Valve (Figure 1)

This Type-1 cylinder valve contains a backcheck which is designed to

prevent propane from flowing until the valve is properly connecting to

a regulator.

When connecting the regulator to the Type-1 cylinder valve, be sure

the pressure relief valve is directed away from the front of the grill and

away from any building. If the pressure relief valve should open, the

propane will then be directed where it is likely to do the least harm if

ignited.

WARNING: Do not insert any foreign objects into the valve

outlet. You may damage the backcheck. A damaged backcheck

can be the source of a leak. Leaking propane may result in

explosion, fire, personal injury or death.

Regulator Coupling Nut

The coupling nut connects to the large outside threads on the valve

outlet. To complete the connection, follow the steps below.

1. Be sure all grill burner knobs, side burner knob and rotisserie

burner knob are in the OFF position.

2. Make sure the cylinder valve handwheel is in the closed position.

Turn clockwise (left to right) to a full stop.

3. Remove the protective caps from the cylinder valve and coupling

nut.

4. Turn the coupling nut clockwise (left to right), to tighten to a full

stop. Be sure the coupling nut is not cross-threaded.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe Tubing, Type L

(Feet) Inside Diameter Outside Diameter

Nat. L.P. Nat. L.P.

0-10 1/2" 3/8" 1/2" 3/8"

1.3 cm 1.0 cm 1.3 cm 1.0 cm

10-40 1/2" 1/2" 5/8" 1/2"

1.3 cm 1.3 cm 1.6 cm 1.3 cm

40-100 1/2" 1/2" 3/4" 1/2"

1.3 cm 1.3 cm 1.9 cm 1.3 cm

100-150 3/4" 1/2" 7/8" 3/4"

1.9 cm 1.3 cm 2.2 cm 1.9 cm

Note: Never use plastic pipe. Check to confirm whether your local codes

allow copper tubing or galvanized.

INSTALLING AND LOCATING YOUR GRILL

The installation must conform with local codes or, in the absence of local

codes, with the National Fuel Gas Code ANSI Z223.1*/ Canadian

Installation Code, CAN/CGA-B149.

*Available from the American National Standards Institute, Inc., 11

West 42nd St., New York, NY 10036.

Qualified Installing Agency

Installation and replacement of gas piping, gas utilization equipment or

accessories and repair and servicing of equipment shall be performed

only by a qualified agency. The term "qualified agency" means any

individual, firm, corporation or company which whether in person or

through a representative is engaged in and is responsible for (a) the

installation or replacement of gas piping or (b) the connection, installa-

tion, repair or servicing of equipment, who is experienced in such work,

familiar with all precautions required and has complied with all the

requirements of the authority having jurisdiction.

Instruction to Installer

1. Installer must leave instruction manual with owner after installation.

2. The owner shall retain this instruction manual for future reference.

3. Installer must have owner fill out and mail warranty card supplied

with appliance.

4. Installer should show owner how to start and operate gas grill.

LOCATION REQUIREMENTS

Location (Figure 2 and Figure 3)

When determining a suitable location take into account concerns such

as exposure to wind, proximity to traffic paths and keeping any gas

supply lines as short as possible. Locate the grill only in well ventilated

area. Never locate the grill in a building, garage, breezeway, shed or

other such enclosed areas. During heavy use the grill will produce a lot

of smoke. Ensure that there is adequate area for smoke to dissipate.

• Minimum clearance from sides and back of unit to adjacent combus-

tible construction below top of unit, 6 inches from sides and 12 inches

from back.

• Minimum horizontal clearance from sides and back of unit to adjacent

vertical combustible construction extending above top of unit, 6

inches from sides and 12 inches from back.

Figure 2

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 5

Figure 3

Figure 4

The cardboard box within your grill contains the following parts:

(Figure 4)

1 box of ceramic plaques (70)

4 grill plates

1 grill plate handle (see page 14, part number 19)

2 elevated cooking racks

1 side burner grate

1 side burner lid

6 burner knobs

1 rotisserie knob

1 chip tray

1 - 5" thermometer for front lid

1 - 2 1/4" thermometer for steamer lid

1 inlet adaptor (LP gas grill only)

1 hose assembly with LP regulator (LP gas grill only)

1 Natural gas regulator (Natural gas grill only)

1 rotisserie rod

1 rotisserie handle

1 counter balance

4 meat forks

1 rotisserie motor

2 rotisserie drip pans

Sequence of Installation of Grill Parts

1. Lay ceramic plaques onto the plaque rack.

2. Place 4 grill plates into grill (flat side or sear side). Your grill plate

handle is used to flip the grill plates to flat side or sear side.

3. Install 2 elevated cooking racks above rotisserie burners.

4. Place side burner grate over side burner.

5. Place side burner lid over side burner grate.

6. Snap 6 burner knobs onto 5 main burner valve stems and onto side

burner valve stem. The inside of a burner knob has a mushroom

pattern.

7. Snap 1 rotisserie burner knob onto rotisserie burner valve stem. The

inside of the rotisserie burner knob has a 3/4 round pattern.

8. Insert chip tray into grill front between the fourth and fifth main

burner knobs.

9. Insert 5" thermometer into grill lid.

10. Insert 2 1/4" thermometer into steamer lid.

11. For LP gas only, thread brass inlet adaptor onto manifold pipe. Use

teflon tape or a LP gas pipe compound to make a gas tight connection

(see Figure 1).

12. For LP gas only, thread brass fitting from hose assembly onto brass

inlet adaptor (see Figure 1). Tighten completely for a gas tight

connection.

13. For Natural gas only, thread Natural gas regulator onto manifold

pipe. Use teflon tape or a Natural gas pipe compound to make a gas

tight connection (see Figure 1).

14. Refer to Rotisserie section, page 9 for installation of rotisserie parts

(see Figure 8).

LEAK TESTING

1. Before lighting your grill, check all connections for leaks using

a mild soapy water solution. DO NOT use matches, lighters or

flame to check for leaks, — you could cause an explosion. With

the grill burner controls turned OFF, slowly open the cylinder

valve by turning the handwheel counterclockwise (right to left).

Apply mild soapy water to the connection. If bubbles appear,

a leak is indicated. Do not put the product in service! Immediately

close the cylinder valve handwheel for propane gas or the manual

shutoff valve for natural gas. A qualified service person must be

contacted to make the needed repairs.

2. DO NOT SMOKE WHILE LEAK TESTING!

3. For LP gas (propane) models, leak test with a full propane cylinder.

Downloaded from www.Manualslib.com manuals search engine

Page 6 R-3848

Figure 5

Air Shutter Adjustment

Be careful as the burners may be very HOT! The air shutters are

located behind the valve cover. There is an access area at the

bottom of the valve cover where you can adjust the air shutter,

with your fingers. A yellow flame indicates insufficient air.

Open the air shutter to allow more air to the burner. If flame is

noisy, blows out, or lifts away from burner or will not light, this

indicates too much air. Close the air shutter.

INSTALLATION CHECK LIST

Note to the Installer: Be sure all items on this list have been thoroughly

completed and checked before operating the grill.

1. Specified clearances maintained to combustibles.

2. All internal packaging removed.

3. Knobs turn freely and bezels centered.

4. Each burner lights satisfactorily, individually or with adjacent

burner lit.

5. Air shutter adjusted.

6. Adjustable low setting satisfactory.

7. Drip trays in place properly and sliding freely.

8. Pressure regulator connected and set for 11.0" w.c. for LP gas.

9. Pressure checked and set at 3.5" w.c. for Natural gas.

10. Grill tested and free of gas leaks.

11. User informed of gas supply shut off valve location.

4. For systems other than self-contained LP gas (propane) sys-

tems:

A. The grill and its individual shut-off valve must be discon-

nected from the gas supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psig

(3.5kPa).

B. The grill must isolated from the gas supply piping system by

closing its own manual shut off valve during any pressure

testing of the gas supply piping system at pressures equal to or

less than 1/2 psig (3.5kPa).

5. After the installation of all gas-related items: i.e. hose, regulator,

LP gas cylinder, natural gas hose or natural gas regulator; the grill

control valves should be turned off and the gas turned on. This is

known as "charging the system." All gas connections must be

checked with a soapy solution while the whole system is under

pressure.

To make a soap solution, mix together an equal amount of liquid

detergent and water.

6. Apply soap mixture to all gas connections. Soap bubbles will

appear if there is a leak. Tighten connections to make a proper seal.

If you cannot stop a gas leak turn off the gas supply and call your

local gas utility, or the dealer from whom the grill was purchased.

Only those parts recommended by the manufacturer should be

used on the Superb gas grill. Substitutions will void the war-

ranty. Do not use the Superb gas grill until all connections have

been checked and do not leak.

A gas system MUST be tested yearly, or whenever the LP gas cylinder

is replaced, or any other gas system part.

ADJUSTING FOR PROPER FLAME AND EFFICIENCY

Air Shutter (Figure 5)

Each burner is tested and adjusted at the factory prior to shipment.

However, variations in the local gas supply may make it necessary to

adjust the burners. The flames of the grill burners should be visually

checked. The rotisserie burners should have a very low flame (no more

than 1/4") and glow with an orange color. There is no air shutter

adjustment for the rotisserie burners. On the main burners and side

burner, the flames should be blue and stable with no, excessive noise or

lifting. If the burners do not operate correctly, check if the air shutter or

burner ports are blocked by dirt, debris, spider webs, etc. and proceed

with air shutter adjustment. The amount of air which is drawn into a

burner is governed by a metal cup at the inlet of the burner called an air

shutter.

WARNING! Before lighting your grill be sure to read this

section carefully.

Turn all knobs to the off position. Inspect the gas supply piping or hose

prior to turning the gas on. If there is evidence of cuts, wear, or abrasion,

it must be replaced prior to use. The replacement pressure regulators and

hose assembly must be the type specified by the manufacturer. Do not

use the Superb gas grill if the odor of gas is present.

For LP gas, the pressure regulator and hose assembly supplied with the

unit must be used. Install the regulator into the tank and check the hose

and regulator connections for leakage with a soap and water solution

before operating your Superb gas grill. Be sure there is gas in the tank.

When lighting your grill always keep your face and body as far

away from the grill as possible.

Lighting the Grill Burners (Figure 6)

The gas grill is equipped with (5) grill burners and (5) piezo ignitors for

the grill burners.

HOW TO LIGHT YOUR GAS GRILL

1. Open the lid.

2. Make sure the grill burner knob to be lighted is in the "OFF"

position.

3. Turn ON gas supply to gas grill.

4. Push and turn the grill burner knob to "HIGH."

5. Be certain that you are turning the ignitor for the grill burner you

intend on using. Rotate ignitor knob clockwise several times. You

will hear a snapping sound, indicating that a spark is being deliv-

ered to the burner. You may need to rotate the ignitor knob several

times before the grill burner lights.

6. If the grill burner does not light in 4 seconds, turn the grill burner

knob to "OFF" and wait 5 minutes before repeating Steps 4 and 5.

7. Each grill burner can also be lit with a match attached to a match

holder, if the ignitor fails to light the grill burner.

8. To light with a match attached to a match holder, insert lighted

match below valve cover, adjacent to the grill burner knob and

through the 1" x 1" square notch on front liner. Turn the grill burner

knob to "HIGH." Remove and extinguish the match quickly when

the grill burner lights.

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 7

USING YOUR SUPERB GRILL

9. If grill burner does not light, turn all knobs to "OFF" and have a

qualified service technician check grill.

10. Turn all knobs to "OFF" and shut off gas supply when not in use.

If the grill burner will not light after several tries, refer to Troubleshoot-

ing section of this manual.

Figure 6

TO PREHEAT GRILL: Once lit, close the lid for approximately 10

minutes to preheat grill.

Lighting the Side Burner

1. Remove the side burner lid and any cooking utensils from the side

burner grate.

2. Make sure the side burner knob is in the "OFF" position.

3. Turn ON gas supply to gas grill.

4. Push and turn the side burner knob to "HIGH."

5. Rotate ignitor knob, between rotisserie burner knob and side burner

knob, clockwise several times. You will hear a snapping sound,

indicating that a spark is being delivered to the side burner. You

may need to rotate the ignitor knob several times before the side

burner lights.

6. If the side burner does not light in 4 seconds turn the side burner knob

to "OFF" and wait at least 5 minutes before repeating Steps 4 and 5.

7. The side burner can also be lit with a match attached to a match

holder if the ignitor fails to light the side burner.

8. To light with a match attached to a match holder, hold the lighted

match next to the side burner ports and turn the side burner knob to

"HIGH." Remove and extinguish the match quickly when the side

burner lights.

9. If side burner does not light, turn knob to "OFF" and have a

qualified service technician check grill.

10. Turn all knobs to "OFF" and shut off gas supply when not in use.

If the side burner will not light after several tries, refer to Troubleshoot-

ing section of this manual.

Lighting the Rotisserie Burner

1. Open the lid.

2. Make sure the rotisserie burner knob is in the "OFF" position.

3. Turn ON gas supply to gas grill.

4. Push and turn the rotisserie burner knob to the LEFT position to

light the left, rotisserie burner. If the right, rotisserie burner is to be

used with the left, rotisserie burner turn to the BOTH position.

5. Rotate the ignitor knob, between rotisserie burner knob and side

burner knob, clockwise several times. You will hear a snapping

sound indicating that a spark is being delivered to the rotisserie

burner. You may need to rotate the ignitor knob several times

before the rotisserie burner lights.

6. If the rotisserie burner does not light in 4 seconds, turn the rotisserie

knob to "OFF" and wait 5 minutes before repeating Steps 4 and 5.

7. The rotisserie burner can also be lit with a match attached to a match

holder if the ignitor fails to light the rotisserie burner.

8. To light with a match attached to a match holder, hold the lighted

match next to the rotisserie burner ports on the left, rotisserie burner

and turn the rotisserie burner knob to LEFT. Remove and extin-

guish the match quickly when the left, rotisserie burner lights. To

light right, rotisserie burner after the left, rotisserie burner has been

lit, repeat process for lighting with a match and turn rotisserie

burner knob to BOTH.

9. If rotisserie burner does not light, turn knob to "OFF" and have a

qualified service technician check grill.

10. Turn all knobs to "OFF" and shut off gas supply when not in use.

If the rotisserie burner will not light after several tries, refer to Trouble-

shooting section of this manual.

Safety Practices to Avoid Injury to Self or Property

1. When lighting a burner always pay close attention to what your

doing. Be certain that you are turning the ignitor labeled for the

burner you intend on using.

2. When using the grill: Do not touch the elevated cooking racks, grill

plates, or immediate surrounding area as these areas become

extremely hot and could cause burns.

3. Use only a dry barbecue mitt, moist or damp potholders on hot

surfaces may cause burns from steam. Do not use a towel or bulky

cloth in place of a barbecue mitt. Do not let potholders touch hot

portions of the grill or grill plates.

4. Grease is flammable. Let hot grease cool before attempting to

handle it. Avoid letting grease deposits collect in the drip pans or

drip trays. CLEAN OFTEN.

5. Do not use aluminum foil to line drip trays or drip pans. This can

severely upset combustion air flow or trap excessive heat in the

control area. The result of this can be melted knobs.

6. For proper lighting and performance of the burners keep the ports

clean. It is necessary to clean them periodically for optimum

performance.

7. NEVER GRILL WITHOUT THE DRIP TRAYS IN PLACE and

pushed all the way to the back of the grill. Without the drip trays,

hot grease could leak downward and produce a fire or explosion

hazard.

8. Do not locate the grill under overhead unprotected surfaces. Use

only in well ventilated areas. Do not use in buildings, garages,

sheds, breezeways, or other such enclosed areas. THIS UNIT IS

FOR OUTDOOR USE ONLY.

9. Keep any electrical supply cord, or the rotisserie motor cord away

from the heated areas of the grill.

10. Never use a dented or rusty LP tank.

11. DO NOT USE CHARCOAL IN THE GRILL.

12. Never place paper inside the grill.

13. Never obstruct the flow of combustion and ventilation air to the

grill.

14. Keep the ventilation opening of the cylinder enclosure free and

clear from debris.

Grill Plates (Figure 7)

An exclusive feature of your Superb gas grill are the stainless steel grill

plates designed to deflect the grease from falling into the burners thereby

reducing flare-ups and extending the life of the burners. The perfora-

tions in the stainless steel evens out the heat and creates a hot surface for

the meat drippings to fall on to. This action turns the drippings into

smoke which passes over the meat resulting in a delicious "charcoal

flavor." The grill plates can be turned over to become sear plates. A grill

plate handle is included to turn over grill plates.

Downloaded from www.Manualslib.com manuals search engine

Page 8 R-3848

Figure 7

1. Since these grill plates transfer heat so quickly, evenly, and

efficiently, you may opt to cook on lower heat settings which may

actually result in fuel savings.

2. For best cleaning results, preheat the grill for approximately 10

minutes and then use a brass bristle brush to clean the grill plates.

3. Most cooking will be done on the "Non-Flat" side. Delicate foods

that could fall through (fish, vegetables, etc.) should be prepared on

the reversible flat side. Since most of these foods are dry by nature,

it is suggested that a light coating of cooking oil be applied to the

grill plates before use. Some foods may stick more than others, but

sticking many times may be attributed to the grill plate being too

hot, and lower heat setting is warranted. Again, experimentation is

the key. A sharp edged spatula is also very helpful.

4. Over time the grill plates may change slightly in color. This is

normal and in no way alters performance or durability.

5. The Superb elevated cooking racks are very versatile and can

actually be used to cook food slower than the main grill area. For

rotisserie use, simply remove by lifting off the elevated cooking

racks and grill plates and replace with drip pans.

COOKING

1. Be sure the drip trays are in place and pushed all the way to the back

of the grill.

2. Light the burners using the lighting instructions.

3. Preheat the grill after lighting with burner knob turned to "HI" for

10 minutes. Keep the lid closed while preheating.

4. Place the food on the grill and cook to the desired doneness. Adjust

the heat setting if necessary. The burner knob may be set to any

position between "HIGH", "MEDIUM" and LO."

5. Turn all knobs to "OFF" and shut off gas supply when you are

finished grilling or after burning residue off grates.

6. Clean the cooking grids, drip trays and drip pans after each use.

Grilling requires high heat for searing and proper browning. Most foods

are cooked at the highest heat setting for the entire cooking time.

However, when grilling large pieces of meat or poultry, it may be

necessary to turn the heat to a lower setting after the initial browning,

this will cook the food completely through without burning the outside.

Foods cooked for a long time or basted with a sugary marinade may need

a lower heat setting near the end of the cooking time. The doneness of

the meat, whether rare, medium, or well done, is affected to a large

degree by the thickness of the cut. Trim any excess fat from the meat

before cooking. To prevent steaks or chops from curling during cooking,

slit the fat around the edges at 2-inch intervals. When defrosting meats,

it is recommended that it be done overnight in a refrigerator as opposed

to a microwave as the microwave can dry out or even partially cook the

meat.

Thermometers

Your Superb grill comes equipped with a thermometer which reads the

air temperature inside of the lid assembly. Also, a second thermometer

is located in the steamer lid which monitors air temperature.

Never allow the air temperature inside the grill to go above 500

°F.

Cooking Chart for Desired Doneness

Insert an instant read thermometer directly into center of meat to check

for doneness.

MEAT RARE MEDIUM WELL

Beef 135° - 140°F 150° - 160°F 170°F

Pork not recommended not recommended 170°F

Poultry not recommended 170°F 185°F

Indirect Cooking

Indirect cooking is a cooking technique that is similar to roasting and

baking in the oven. To cook with indirect heat turn Burner 1 and Burner

5 on High and Burner 3 on Low. Refer to the Cooking Chart for desired

doneness of meat. Also, pastries can be baked with the same indirect

cooking technique. Baking time will be similar to the recipe instruc-

tions. Monitor the thermometer in the lid to maintain temperature in any

recipe instructions. All burner settings may need to be adjusted, depend-

ing on outside temperature and wind conditions.

Flare-Ups

Always remember to pre-heat the grill for ten (10) minutes before

starting to cook. When you cook fatty foods over an open flame, you can

expect flare-ups. Natural juices falling on the hot plaques result in flame

and smoke that give foods cooked on your grill that delicious outdoor

flavor and appearance. Expect and encourage a moderate amount of

flare-up. Excessive flare-ups occur when cooking extra fatty foods, or

if cooking temperatures are too high. Control flare-ups by:

1. Turn your burner knob to a lower setting.

2. Move the meat to another part of the grill, if possible. You can cook

on one side and move food, as necessary, to the unlighted side.

3. Trim of excess fat before cooking.

4. To avoid flare-ups fatty meats should be cooked on the medium

setting.

5. Cook with the lid assembly down. Cutting off the flow of air will

reduce the possibility of flare-ups.

6. If you need to immediately control an excessive flare-up, throw a

small amount of baking soda directly on the plaques and lower heat

setting.

NOTE: Do not douse flare-ups with liquid as this can intensify

the flame and harm the grill plates.

Chip Tray

Your Superb gas grill includes a built-in chip tray which installs directly

into the front of grill. We believe that wood chips enhance the flavor of

everything that is grilled. To use the chip tray, place a handful of soaked

wood chips in the tray, then ignite the burners to the left and right of the

tray. Turn the burners on "HI" for 10 minutes. Next reduce the flame to

"MEDIUM" or "LO" to keep the chips from burning too fast.

CAUTION: When adding more chips to the tray the handle

on tray may be Hot.

Top Burners

Your Superb gas grill is equipped with (5) grill burners, each rated at

12,000 BTUH and has (5) spark ignitors for easy lighting. Provided for

use with your side burner rated at 30,000 BTUH is a stainless steel lid

which doubles as work surface when the burner is not in use. When using

the grill with the side burner covered, be careful as heat can conduct from

the grill and cause the lid to heat up. Always remove the lid before

lighting the side burner.

Never light or use the side burner with the lid in place.

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 9

Rotisserie (Figure 8)

The (2) rotisserie burners, each rated at 12,000 BTUH, are an infrared

type which provide intense searing radiant heat. This intense heat is

perfect for searing in the natural juices and nutrients found in quality

cuts of meats. When lit, the rotisserie burners will reach cooking

temperatures in about 3 minutes. The orange/red glow will even out in

about 5 minutes.

The rotisserie motor is equipped with gears capable of turning up to a 20

lb. cut of meat or poultry. The motor is mounted to a stainless steel bracket

which attaches to the left side of the grill. The rotisserie motor must be

electrically grounded in accordance with local codes or, in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70 or

Canadian Electrical Code, CSA C22.1, if an external electrical source is

utilized.

WARNING! DO NOT use the rotisserie and the 5 main burners

at the same time! You CAN use the LEFT rotisserie and the two

far RIGHT main burners (#4 and #5) at the same time.

Figure 8

Counterbalance

Counterbalance is used to balance the rotisserie rod when cooking large

or irregular pieces of food. The food will always be placed on the

rotisserie rod between the motor and counterbalance. Adjust the coun-

terbalance on the rotisserie rod until the food turns in an even motion.

The rotisserie rod for the rotisserie fits into the motor assembly by

placing the pointed end into the motor and the opposite end on the

support at the right side of the grill. With the rotisserie rod pushed in as

far as possible into the motor, the grooved rotisserie rod should rest on

the right side bracket. The removable handle should only be in place

when handling the rotisserie rod.

When using the side burner, remove the rotisserie rod handle

to prevent it from getting hot!

To load the rotisserie rod begin with the handle in place, and slide one

of the meat forks with prongs facing away from the handle onto the

rotisserie rod. Push the rotisserie rod through the center of the food, then

slide the second meat fork with prongs towards the food on the rotisserie

rod. Center the food on the rotisserie rod then push the meat forks firmly

into the food. Tighten the wing nuts. It may be necessary to wrap the food

with butchers string (never use nylon or plastic string) to secure any

loose portions.

Once the food is secure, attach the counterbalance to rotisserie rod.

Remove the elevated cooking racks and grill plates. Insert the drip pans

into grill onto the ceramic plaques. Center drip pan(s) under food being

rotisserized. Insert the rotisserie rod into the motor. Turn on rotisserie

motor and adjust counterbalance.

NOTE: After the first use of your rotisserie it is likely that the stainless

steel above the rotisserie burners will darken to a dark, blue color. The

electric motor should be removed and stored in a dry place when not in

use.

Figure 9

Grill Light (Figure 9)

Exclusive on Superb grill is the grilling area fluorescent light. The

fluorescent light is wired at the factory and should be plugged directly

into a properly grounded three-pronged receptacle. Raise light and slide

to left to lock into position.

Replacement of Fluorescent Bulb

1. Remove electrical cord for fluorescent bulb from electrical receptacle.

2, Remove light housing front from light housing rear by removing (3)

Phillips head screws located at bottom of light housing front.

3. Replace fluorescent bulb with part number R-3932, fluorescent bulb.

Refer to page 12 for ordering repair parts.

4. Attach light housing front onto light housing rear with (3) Phillips

head screws from Step 2.

Steamer

Use your steamer for steaming vegetables and for keeping food warm.

Optional large and small steamer pans, SSP-1 are available for the

steamer.

Elevated Cooking Racks

The two cooking racks can be used to cook food with indirect heat. The

cooking time will be increased but the food will be moist and flavorful.

The rotisserie burners are located beneath the elevated cooking racks.

Grease may accumulate on the rotisserie burners from use of the

elevated cooking racks. Ignite rotisserie burners to "burn off" any grease

accumulation. The elevated cooking racks must be removed when the

rotisserie burners are in use.

Downloaded from www.Manualslib.com manuals search engine

Page 10 R-3848

Stainless Steel

The Superb gas grill is made from stainless steel. There are many different

stainless steel cleaners available. Always use the mildest cleaning meth-

ods first, scrubbing in the directions of the grain. To touch up noticeable

scratches in the stainless steel, sand lightly with dry 100 grit emery paper

or scotch bright pad in the direction of the grain. Specks of grease can

gather on the surfaces of the stainless steel and bake on to the surface

giving the appearance of rust. To remove this grease buildup scrub with

a strong degreaser in the direction of the grain. Coat with lemon oil or a

stainless steel shine product to protect its finish after cleaning.

Cleaning Grill Plates

The grill plates should be cleaned regularly because of grease build-up

and other debris. Keeping the grill plates clean will greatly reduce flare

ups and grease fires.

The easiest way to clean the grill is immediately after cooking is

completed. Be sure the burners are turned off and there are no flames

before beginning. Wear a barbecue mitt to protect your hand from the heat

and steam. Using a brass bristle barbecue brush, scrub the hot grill plates.

If the grill is allowed to cool before cleaning, the cleaning process will be

more difficult.

NOTE: DO NOT USE CAUSTIC CLEANERS such as oven

cleaners, etc. This will damage the grid surface and void your

warranty.

Side Burner Grate

The side grate is stainless steel. Do not attempt to clean a hot grate. When

the grate cools it may be wiped with hot soapy water, then rinsed and

wiped dry. Never immerse a hot grate in water as the hot steam produced

could cause burns.

Drip Trays

The drip trays will collect grease from the grill area. Do not attempt to

remove or clean until thoroughly cooled. To avoid grease fires or flare-

ups be sure to clean out the grease often.

Grill Burners

The grill burners are constructed of cast stainless steel and should only

require minimal maintenance. However, they should be checked periodi-

cally and cleaned if needed.

Figure 10

Side Burner

The side burner is constructed of cast stainless steel. Occasional cleaning

of the burner ports will be necessary.

Flashback from Spiders (Figure 10)

In some areas of the country, spiders or small insects have been found to

create "flashbacks" problems. The spiders spin webs and/or insects build

nests in the burner venturi tube(s). The web and/or nests can lead to gas

flow obstruction which results in a "flashback" (a fire in the venturi

tube(s). Clean interior of burners with a flexible, soft bristle, bottle brush

in order to remove spiders, spider webs and debris.

CLEANING PRODECURES

Removing Main Burners (Figure 11)

1. Turn OFF gas supply to grill.

2. All grill parts must be cool before attempting to clean.

3. Remove the chip tray.

4. Remove (4) grill plates.

5. Remove ceramic plaques and plaque rack.

6. Remove (5) burner hoods located above main burners.

7. Remove right end and left end of inner liner by removing (2) screws

from each end.

8. Remove inner liner by removing (6) screws.

9. Remove (1) bolt from each main burner.

10. Lift rear section of main burner in order to remove main burner from

orifice fitting.

11. Clean interior of main burner with a flexible, soft bristle, bottle brush

in order to remove spiders, spider webs and debris. Apply air

pressure to burner ports to remove debris.

12. Be careful not to change the air shutter's original position. Once

reinstalled, light all of the burners and check for proper flame.

13. To replace main burners, reverse above procedure starting with Step

10.

Removing Side Burner (Figure 11)

1. Turn OFF gas supply to grill.

2. All grill parts must be cool before attempting to clean.

3. Remove side burner lid.

4. Remove side burner grate.

5. Remove (2) screws from side burner.

6. Lift rear section of side burner in order to remove side burner from

orifice fitting.

7. Clean interior of side burner with a flexible, soft bristle, bottle brush

in order to remove spiders, spider webs and debris. Apply air

pressure to burner ports to remove debris.

8. To replace side burner, reverse above procedure starting with Step

Additional Steps to Clean Main Burners and Side Burner

1. Turn OFF gas supply to grill.

2. All grill parts must be cool before attempting to clean.

3. Clean the exterior of the burner with a wire brush.

4. Clear any clogged ports with a straightened paper-clip.

5. Never use a wooden toothpick as it may break off and clog the port.

6. Shake out any debris through the air shutter.

7. Use a flashlight to inspect the burner inlet to ensure it is not blocked.

8. If an obstruction can be seen, use a straightened metal wire coat-

hanger to clean it out.

CARE AND MAINTENANCE

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 11

Figure 11

Removing Rotisserie Burners and Rotisserie Burner Orifices

(Figure 12)

1. Turn OFF gas supply to grill.

2. All grill parts must be cool before attempting to clean.

3. Remove (1) screw from each rotisserie burner electrode.

4. Pull forward on the electrode to expose approximately 3 inches of the

electrode wire.

5. If you are replacing the electrode, remove the electrode wire from the

electrode. Do not allow the electrode wire to slip back into the access

hole.

6. If you are not replacing the electrode, allow the electrode to lay on

the cooking surface.

7. Remove (6) screws from the brackets for the elevated cooking racks.

The brackets are located at each end (2 brackets) and between (1

bracket) the rotisserie burners.

8. At the center of the gas grill, grasp the end of rotisserie burner, pull

forward and slide the opposite end of the rotisserie burner from the

orifice fitting.

9. Apply air pressure into the face and end of the rotisserie burner to

remove spiders, spider webs, dust, lint and debris. A flexible, soft

bristle, bottle brush can be used to clean the interior of the rotisserie

burner.

10. Remove the rotisserie burner orifice from the orifice fitting.

11. Apply air pressure into the rotisserie burner orifice and orifice fitting

to remove spiders, spider webs, dust, lint and debris. A flexible, soft

bristle, bottle brush can be used to clean the orifice fitting.

12. To reinstall components, reverse above procedure starting with Step

10.

Figure 12

Cleaning the Orifices

No regular maintenance should be needed for the orifices. They should

only be removed if it is determined that there is a blockage.

Warning: Serious injury may occur if the orifice is not located

properly in the orifice fitting when reassembled.

Removing and Replacing the Piezo Ignitors and Electrodes

1. Remove all gas control knobs and ignitor knobs.

2. Remove chip tray.

3. Remove valve cover (7 screws).

4. Piezo ignitors are located at rear of valve cover.

5. Remove (1) screw for each electrode.

6. Remove (2) screws for each piezo ignitor.

7. Reverse above procedure to replace components.

Downloaded from www.Manualslib.com manuals search engine

Page 12 R-3848

HOW TO ORDER REPAIR PARTS...

All parts listed in the Parts List have a part No. When ordering parts, first obtain the Model No. from the nameplate on your equipment. Then determine

the Part No. (not the Index No.) and the Description of each part from the appropriate illustration and list. Be sure to give all this information...

Grill Model Number Part Description

Grill Serial Number Type of Gas (Propane or Natural)

Part Number

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. Order parts through your

local dealer.

Shipments contingent upon strikes, fires, and all causes beyond our control.

1. Grill won't light when the rotary ignitor is turned.

a. With the gas tuned off, remove the grill plates, ceramic

plaques and plaque rack. Turn the ignitor knob clockwise

to check the spark. You should see a spark jump from tip of

the ignitor. If there is a spark, check the gas supply. Is the

tank full? Is the line purged of air? Can you light the burner

with a match?

b. Check air shutter adjustment, close as needed.

c. Do other burners light?

d. Check the orifice for blockage.

e. Is the ignitor tip clean and free from debris?

f. Clean ignitor tip.

2. Burner flame is yellow or orange and there is a smell of gas.

a. Check the burner inlet for obstructions.

b. Check the air shutter for proper adjustment.

c. Check for spiders, spider webs and debris.

3. Low heat with control knob set on "HI."

a. Is the fuel hose bent or kinked?

b. Is there an adequate gas supply?

TROUBLE-SHOOTING

If your Superb gas grill does not function properly, use the following checklist before contacting your dealer for service.

You may save the cost of a service call.

c. If there is only one burner that appears low, does the orifice

or burner need cleaning?

d. Is the air shutter too far open or closed?

e. Is the gas supply, or gas pressure low?

f. Has the grill been preheated for at least 10 minutes?

4. The smell of gas with flames appearing yellow or the gas grill

does not reach temperature and heats unevenly.

a. Check for spiders or insects.

b. Spiders and insects can nest in the burner of this or any

grill, and cause a disruption in the flow of gas from the

burner. This is dangerous and can cause a fire behind the

valve cover, damaging the grill and making it unsafe to

operate.

You should inspect the burners periodically or immedi-

ately if any of these conditions occur or persist.

5. The burners make popping noises.

a. Check air shutter adjustment.

b. Check burners for clogged ports.

Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529

Adjusting Main Burner Electrodes

1. Remove four (4) grill plates.

2. Remove ceramic plaques.

3. Remove plaque rack.

4. Remove five (5) burner hoods from five (5) main burners.

5. Remove five (5) collector boxes from five (5) main burner electrodes,

one (1) 10 - 16 x 1/2" Phillips stainless steel screw for each collector

box.

6. At this time, check for proper sparking of the electrodes. Turn

electrode knob, the spark should occur between the second and third

port hole on main burner.

To adjust spark angle you will use two (2) needle nose pliers.

Grasping electrode wire 1/2" back from tip of electrode with first

pair of needle nose pliers adjust tip of electrode with second pair of

needle nose pliers.

7. Check ignition of main burners. Make additional adjustments to

electrodes if required.

8. Locate main burner with electrode that is to the left of chip tray.

Place collector box over electrode. Place flange on collector box

beneath flange on chip tray guide. The clearance hole in collector

box will align with clearance hole in chip tray guide. Insert and

attach one (1) 10-16 x 1/2" Phillips stainless steel screw from Step

5 through chip tray flange and collector box flange and into bottom

of inner liner.

9. Place four (4) additional collector boxes over four (4) additional

main burners with electrodes.

10. Attach four (4) collector boxes to bottom of inner liner with four

(4) 10-16 x 1/2" Phillips stainless steel screws from Step 5.

11. Replace five (5) burner hoods over five (5) main burners.

12. Replace plaque rack.

13. Replace ceramic plaques onto plaque rack.

14. Replace four (4) grill plates.

15. Adjustment of main burner electrodes is completed.

Downloaded from www.Manualslib.com manuals search engine

R-3848 Page 13

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

Index Part

No. Number Description

Index Part

No. Number Description

1 SSG-140 STEAMER LID ASSEMBLY

1A SSG-126 HANDLE - STEAMER LID

2 R-4005 SHOULDER SCREW (STEAMER) (2 REQ’D)

3 R-3987 THERMOMETER - STEAMER

4 SSG-040 STEAMER BODY

5 R-4010 NUT (4 REQ’D) 1/4-20 STAINLESS

6 SSG-029 WIND GUARD

7 SSG-030 TOP-BACK

8 SSG-105 TOP END-LEFT WELDED ASSEMBLY

9 SSG-106 TOP END-RIGHT WELDED ASSEMBLY

10 R-4003 MOTOR

11 SSG-055 ROTIS MOTOR SUPPORT

12 R-3999 SHOULDER SCREW (COVER) (2 REQ’D)

13 SSG-107 LID ASSEMBLY-COMPLETE

13A SSG-109 HANDLE - COVER LID

13B R-3928 HANDLE BRACKET - LEFT

13C R-3929 HANDLE BRACKET - RIGHT

13D R-3930 INSULATOR (4 REQ’D)

14 R-3857 THERMOMETER - COVER

15 R-3877 ROTIS ROD

16 R-3960 MEAT FORK (4 REQ’D)

17 R-3957 COUNTERBALANCE

18 R-3910 HANDLE - ROTIS ROD

19 R-3881 GRATE REMOVER

20 SSG-112 GRILL PLATE WELDED ASSEMBLY (4 REQ’D)

21 R-3995 CERAMIC PLAQUE (BOX OF 70)

22 SSG-116 PLAQUE RACK WELDED ASSEMBLY

23 SSG-003 CASING BACK

24 SSG-056 ROTIS SUPPORT TOP

25 SSG-051 ROTIS SHIELD (NAT GAS ONLY)

26 SSG-060 ROTIS SUPPORT-LEFT

27 SSG-059 ROTIS SUPPORT-RIGHT

28 SSG-057 ROTIS SUPPORT CENTER

29 SSG-137 WIRE TUBE (2 REQ’D)

30 SSG-062 ROTIS SUPPORT COVER-LEFT

31 SSG-058 ROTIS SUPPORT COVER-CENTER

32 SSG-061 ROTIS SUPPORT COVER-RIGHT

33 R-3955 ELECTRODE WIRE ASSEMBLY - 52" LONG (2

REQ’D)

34 R-3915 ELECTRODE (2 REQ’D)

35 SSG-117 ELEVATED COOKING RACK (2 REQ’D)

36 R-2319 ORIFICE - ROTIS BURNER (LP GAS ONLY) (2

REQ’D)

36 R-4000 ORIFICE - ROTIS BURNER (NAT GAS ONLY) (2

REQ’D)

37 P-232 ORIFICE HOLDER (2 REQ’D)

38 R-3919 BURNER - ROTIS (2 REQ’D)

39 SSG-031 GRILL RACK SUPPORT CENTER

40 SSG-054 GRILL RACK SUPPORT END (2 REQ’D)

41 SSG-136 INLET TUBING ASSEMBLY - ROTIS VALVE TO

ROTIS BURNER - LEFT

42 SSG-135 INLET TUBING ASSEMBLY - ROTIS VALVE TO

ROTIS BURNER - RIGHT

43 SSG-134 INLET TUBING ASSEMBLY - MANIFOLD TO

ROTIS VALVE

44 R-3870 VALVE - ROTIS

45 SSG-052 VALVE BRACKET-ROTIS

46 R-1652 VALVE NUT

47 R-4007 BRASS MALE CONNECTOR (BODY ONLY)

48 SSG-111 SIDE BURNER LID ASSEMBLY

49 SSG-118 SIDE BURNER GRATE WELDED ASSEMBLY

50 SSG-022 BURNER HOOD (5 REQ’D)

51 SSG-020 CHIP TRAY GUIDE (2 REQ’D)

52 R-3967 SIDE BURNER

53 R-3358 AIR SHUTTER (6 REQ’D)

54 SSG-103 SIDE BURNER BRACKET WELDED ASSEMBLY (2

REQ’D)

55 SSG-099 CASING SIDE-LEFT SUB-ASSEMBLY

56 SSG-014 INNER LINER SIDE (2 REQ’D)

57 SSG-013 INNER LINER

58 SSG-010 CASING DIVIDER

59 SSG-025 INNER LINER SIDE BURNER-LEFT

60 SSG-024 INNER LINER-SIDE BURNER

61 R-3958 ELECTRODE AND WIRE ASSEMBLY - SIDE

BURNER

62 SSG-026 INNER LINER SIDE BURNER-RIGHT

63 SSG-100 CASING SIDE-RIGHT SUB-ASSEMBLY

64 R-3916 MAIN BURNER (5 REQ’D)

65 SSG-019 CHIP TRAY

66 SSG-053 ROTIS WIRE GUIDE

67 SSG-102 CASING FRONT ASSEMBLY

68 SSG-104 LIGHT HOUSING-REAR WELDED ASSEMBLY

69 R-3934 SHOULDER SCREW (LIGHT) (2 REQ’D)

70 R-4020 CORD SET

71 SSG-005 FRONT SHIELD

72 R-3873 CONTROL ROD

73 SSG-004 FRONT LINER

74 R-3921 ELECTRODE AND WIRE ASSEMBLY - MAIN

BURNER (5 REQ’D)

75 SSG-016 INNER LINER SPACER

76 SSG-015 GREASE PAN SHIELD (5 REQ’D)

77 SSG-049 MANIFOLD BRACKET REAR-UPPER

78 SSG-050 MANIFOLD BRACKET REARLOWER

79 SSG-101 BURNER SUPPORT WELDED ASSEMBLY

80 SSG-007 WIRE CHANNEL-LEFT

81 SSG-009 GREASE PAN DIVIDER

82 SSG-008 WIRE CHANNEL-RIGHT

83 SSG-017 GREASE PAN-LEFT

84 SSG-018 GREASE PAN-RIGHT

85 SSG-023 VALVE COVER SUPPORT (4 REQ’D)

86 R-3357 SPRING (6 REQ’D)

87 R-3874 VALVE AND ORIFICE ASSEMBLY - NAT ONLY -

MAIN BURNER (5 REQ’D)

87 R-4112 VALVE AND ORIFICE ASSEMBLY - LP ONLY -

MAIN BURNER (5 REQ’D)

88a R-4118 VALVE - NAT ONLY - SIDE BURNER

88a R-4119 VALVE - LPG ONLY - SIDE BURNER

88b R-4121 ORIFICE ASSEMBLY - LP ONLY - SIDE BURNER

88b R-4120 ORIFICE ASSEMBLY - NAT ONLY - SIDE

BURNER

89 R-3908 PIEZO IGNITOR (5 REQ’D)

90 R-3966 PIEZO IGNITOR (3-SPARK)

91 SSG-012 VALVE COVER

92 R-3918 KNOB (MAIN AND SIDE BURNERS) (6 REQ’D)

93 R-3909 KNOB (6 REQ’D) (PIEZO IGNITORS)

94 R-3872 KNOB (ROTIS BURNER)

95 R-3939 GLASS

96 R-3940 BULB CLIP

97 R-1468 STRAIN RELIEF BUSHING

98 R-3932 BULB - FLUORESCENT

99 R-3933 SOCKET

100 R-3931 BALLAST

101 R-3920 SWITCH

102 SSG-035 LIGHT MOUNTING BRACKET

103 SSG-032 LIGHT HOUSING-FRONT

104 SSG-110 MANIFOLD WELDED ASSEMBLY

105 R-4015 PRESSURE REGULATOR (NAT GAS ONLY)

106 R-3993 INLET ADAPTOR (LP GAS ONLY)

107 R-3992 HOSE ASSEMBLY 22" LONG (LP GAS ONLY)

108 R-4660 COVER END SPACER (2 REQ’D)

NOT SHOWN R-4052 DRIP PAN (2 REQ’D) STAINLESS

NOT SHOWN R-4116 ORIFICE NAT #50 - MAIN BURNER

NOT SHOWN R-4117 ORIFICE LP #60 - MAIN BURNER

NOT SHOWN R-4120 ORIFICE NAT #37 - SIDE BURNER

NOT SHOWN R-4121 ORIFICE LP #51 - SIDE BURNER

NOT SHOWN R-734 LIGHTER ROD

NOT SHOWN SSG-166 ROTIS SUPPORT-CENTER GASKET

NOT SHOWN SSG-168 ROTIS SUPPORT COVER-CENTER GASKET

NOT SHOWN SSG-176 COLLECTOR BOX (5 REQUIRED)

NOT SHOWN R-7067 ADAPTOR 3/8" MALE SAEX, 1/2" MALE NPT

Downloaded from www.Manualslib.com manuals search engine

Page 14 R-3848

Downloaded from www.Manualslib.com manuals search engine

Broilmaster SSG-36 Le manuel du propriétaire

Marque: Broilmaster

Modèle: SSG-36

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

SSG-36-1

Télécharger le PDF

rapport

dans d''autres langues

English: Broilmaster SSG-36 Owner's manual

Broilmaster SSG-36 Le manuel du propriétaire

Ce manuel convient également à

Broilmaster SSG-36 Le manuel du propriétaire

dans d''autres langues

Autres documents