Fanimation LP8577LBL Le manuel du propriétaire
- Catégorie
- Ventilateurs ménagers
- Taper
- Le manuel du propriétaire
Español p.
MODEL #LP8577**
UPRIGHT
™
CEILING FAN
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.
ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM
READ AND SAVE THESE INSTRUCTIONS
Serial Number
Purchase Date Net Weight 16.71 lbs (7.58 kg)
20
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly
diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling
fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without
blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70) and Local Codes. The
ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or
approved by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to
exceed 35 lbs. or 15.88 kgs.). See page 5 of owner’s manual for support requirements. Consult a qualified electrician if in
doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate
electrical knowledge or experience, have your fan installed by licensed electrician.
6. Suitable for use with solid-state speed controls.
WARNING
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,
ISOLATING WALL CONTROL/SWITCH.
WARNING
:
This product is designed to use only those parts supplied with this product and/or accessories designated
specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in
personal injury or property damage.
WARNING
:
To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the
WARNING
:
Mount to an outlet box marked acceptable for fan support.
brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship
during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective
fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs
incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due
to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service
center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all
costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or
workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our
national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,
corroding, tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to
extremes of heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store
that
sold the fan or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this
warranty.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
5. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with the appliance.
8. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a
grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be
connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it
should be connected to an equipment-grounding conductor.
WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage
to the ceiling fan's remote control unit.
7. This fan is to be used in dry location only.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other
expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to
those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow
limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out
of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you
special legal rights and you may also have other rights that vary from state to state.
10.A certain amount of wobble is normal and should not be considered a problem or a defect.
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .5
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .5
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .7
How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .9
How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . 10
How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . . 11
How to Assemble Your Ceiling Fan Blades . . . . . . . . . . . . . . .
How to Assemble Your Light Kit or Cap . . . . . . . . . . . . . . . .
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
How to Install Your Remote Control . . . . . . . . . . . . . . . . . . . . .15
How to Clean Your Ceiling Fan Blades. . . . . . . . . . . . . . . . . . .15
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table of Contents
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must
accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly
packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
.12
11
Four wire connectors supplied
1. Check to see that you have received the following parts:
NOTE:
If you are uncertain of part description, refer to
exploded view illustration.
4
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check
mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should
you be interrupted.
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any
accessories designated specifically for use with this
product by Fanimation. Substitution of parts or
accessories not designated for use with this product
by Fanimation could result in personal injury or
property damage.
otor sse ly
anger racket sse ly
ownrod anger all sse ly
Ceiling Canopy
Canopy crew Cover sse ly
otor Coupling Cover sse ly
Ceiling Canopy
Hanger Bracket
Assembly
Downrod/Hanger Ball
Assembly
Hardware Bags
Hand-Held RemoteReceiver Unit
Hand-Held Remote
Blade Set
This manual is designed to make it as easy as possible for you to assemble,
install, operate and maintain your ceiling fan
Tools Needed for Assembly
ne hillips head screwdriver
One stepladder
nstalled ire ength
ire i e
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 10). If you
feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
One wire stripper
p to ft
ft
One lade
screwdriver
Materials
iring outlet o and o connectors ust e of type
re
uired y the local code he ini u wire would e a
conductor wire with ground of the following si e:
NOTE:
Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are
missing contact your local retailer.
Canopy Screw
Cover Assembly
Motor Coupling
Cover Assembly
Motor Assembly
/LJKW.LW*ODVV$VVHPEO\
/('$VVHPEO\
/LJKW.LW:LUH&RYHU
Steel Cap
lade et
5HFHLYHU8QLW
ardware ags:
–
ire Connectors
–
alance it
7HQÝZDVKHUKHDGVFUHZV
EODGHWRPRWRUKXE
–
7HQ)LEHU:DVKHU–
Light Kit/Glass Assembly
LED Assembly
Steel Cap
Light Kit Wire Cover
5
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the ceiling
fan. Here are a few tips to ensure efficient product
performance.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counter-
clockwise direction. The airflow produced by the ceiling
fan creates a wind-chill effect, making you “feel” cooler.
Select a fan speed that provides a comfortable breeze,
lower speeds consume less energy.
WinterSeason: Reversethe motorandoperate theceiling
fan at low speed in the clockwise direction. This produces
a gentle updraft, which forces warm air near the ceiling
down into the occupied space.Remember to adjust your
thermostat when using your ceiling fan - additional energy
and dollar savings could be realized with this simple step!
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.
Electrical code requires use of a fan-rated outlet box to
support the extra weight and motion associated with a
ceiling fan. A fan-rated box will be labeled as such and
typically supports up to a 70lbs ceiling fan. Fan-Rated
Outlet Boxes vary in ratings and design. Ensure the
ratings of your ceiling fan outlet box meet the
requirements for the ceiling fan being installed. Figure 1,
Figure 2 and Figure 3 depicts different structural
configurations that may be used for mounting the
outlet box.
Low-profile use (Figure 1)
A 1
2-in.-deep pancake box is meant to be screwed to a
joist or block. It’s used if only one cable is coming into
the box. It is also available in a saddle-mount
configuration.
CEILING
2" x 4"
CEILING JOIST
OUTLET BOX
Figure 1
Figure 2
2" x 4"
CEILING JOIST
CEILING
OUTLET BOX
Deep-profile use (Figure 2)
A 2-1
-in.-deep box can be attached to blocking
between joists and is roomy enough to handle more
than one cable.
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle
of the room and at least 7 feet from floor to the blade and
18 inches from wall to the blade. If ceiling height allows,
install the fan 8 - 9 feet from floor to the blade for optimal
airflow. Consult your Fanimation Retailer for optional
mounting accessories.
6
Electrical and Structural Requirements (Continued)
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and
remove the existing light fixture.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
acceptable for fan support of 15.88 kg (35 lbs) or less.
Use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to
be replaced. Consult a qualified electrician if
in doubt.
WARNING
Brace use (Figure 3)
Paired with a deep box, this hanger is meant to span
between two joists and takes the place of wooden
blocking.
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
WARNING
Figure 3
CEILING JOIST
CEILING
OUTLET BOX
Do not operate this fan with a variable (Rheostat) wall
controller or dimmer switch. Doing so could result in
damage to the ceiling fan's remote control unit.
WARNING
7
How to Assemble Your Ceiling Fan
1. Remove the hanger ball portion from the downrod/
hanger ball assembly by loosening the set screw in the
hanger ball until the ball falls freely down the downrod.
Remove the pin from the downrod, then remove the
hanger ball. Retain the pin and hanger ball for reinstal-
lation in Step 7. (Figure 1)
Downrod
Set Screws (2)
Figure 1
Figure 2
5. Thread downrod into the downrod support on top of
the motor. Install the clevis pin by aligning the holes
in the downrod support with holes in the downrod.
Secure clevis pin with hairpin clip. Tighten the two set
screws with nuts in the downrod support. (Figure 5)
WARNING
It is critical that the clevis pin in the downrod support
is properly installed and the set screws and nuts are
securely tightened. Failure to do so could result in
the fan falling.
2. Remove the hairpin clip and clevis pin from the
bottom of the downrod. Retain the pin and clip for
reinstallation in Step 5. (Figure 2)
Hairpin
Clip
Clevis Pin
Downrod
Set Screws and
Locking Nuts (2)
Hairpin Clip
Figure 5
Figure 4
Black, White, orange and
Blue Wires
4. Loosen the two set screws and locking nuts in
the downrod support of the motor assembly. Route
the black, white, orange and blue wires through the
downrod. (Figure 4)
3. Remove the three stabilizer tabs and plastic bag
from the motor. Discard the stabilizer tabs. (Figure 3)
Figure 3
Stabilizers Tabs
Motor
Assembly
Clevis Pin
Downrod
Set Screw
Hanger Ball
Pin
Figure 6
6. Route wires through motor coupling cover, canopy
screw cover and ceiling canopy. (Figure 6)
Motor Coupling
Cover
Ceiling Canopy
Canopy Screw
Cover
8
How to Assemble Your Ceiling Fan (continued)
8. Cut off excess leadwire approximately 6 to 9 inches
above top of the downrod. Strip insulation off 1/2 inch
from the end of each lead wire. (Figure 8)
Figure 7
Figure 8
NOTE:
All set screws must be checked, and retightened
where necessary, before installation.
7. Reinstall the hanger ball on the downrod as
follows. Route the black, white, blue and orange wires
through the hanger ball. Position the pin through the
two holes in the downrod and align the hanger ball
so the pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against the
pin. Securely tighten the set screw in the hanger
ball. A loose set screw could create fan wobble.
(Figure 7)
2. Carefully lift the fan and seat the downrod/hanger ball
assembly on the hanger bracket that was just attached
to the outlet box. Be sure the groove in the ball is lined
up with tab on the hanger bracket. (Figure 4)
This fan is intended for standard and angled mounting
options only. Closemount and flushmount options are
not available. For angled ceilings, note the angle can
be no more than 19°.
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or ſre hazard.
WARNING
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
1. Securely attach the hanger bracket to the outlet box
(not included) using the outlet box screws and washers
supplied with the outlet box. (Figure 3)
WARNING
The outlet box must be securely anchored. Hanger
bracket must seat ſrmly against outlet box. If the
outlet box is recessed, remove wall board until bracket
contacts box. If bracket and /or outlet box are not
securely attached, the fan could wobble or fall.
Figure 3
Figure 4
Outlet Box
Hanger
Bracket
Downrod/Hanger
Ball Assembly
Outlet Box
Hanger
Bracket
Screw (2)
Supplied with
Outlet Box
Tab
Flat Washer
9
How to Hang Your Ceiling Fan
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
The fan must be hung with at least 7’ of clearance
from
oor to blades. (Figure 2)
WARNING
To avoid possible re or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 1)
Figure 2
CEILING
FLOOR
NO LESS
THAN
7 FEET
Figure 1
MAIN FUSE BOX
MAIN FUSE BOX
Figure 2
Figure 1
Figure 4
Green Wire
from Supply
(Ground)
White Wire
from Supply
White Wire
from Receiver
Green Wire
from Hanger
Bracket (Ground)
Green Wire
from Hanger
Ball (Ground)
Listed
Outlet Box
Household
Supply
Black Wire
from Supply
Black Wire
from Receiver
Receiver
Figure 3
x 7WIRE
CONNECTORS
HARDWARE USED:
Dip Switch
ON DIP
1 2 3 4 5
Receiver Unit
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring
(Figure 2).
WARNING
NOTE:
If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice, as
it must be grounded for safe operation.
NOTE:
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan installed
by a licensed electrician.
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors except for the ground wire. Do not
operate fan until the blades are in place. Noise and
motor damage could result.
WARNING
3. After connections have been made, turn leads
upward and carefully push leads into the outlet box,
with the white and green leads to one side of the box
and the black leads to the other side. (Figure 4)
CAUTION: INCORRECT WIRE CONNECTION WILL
DAMAGE THIS RECEIVER.
2. Connect green wires from hanger bracket and
hanger ball to bare (ground) wire using wire connector.
Connect black wire from receiver unit marked “AC IN L”
to black supply wire using wire connector. Connect white
wire from receiver unit marked “AC IN N” to white supply
wire using wire connector. Connect white wire from
receiver unit marked “TO MOTOR N” to white wire from
fan using wire connector supplied with receiver unit.
Connect black wire from receiver unit marked “TO
MOTOR L” to black wire from fan using wire connector
supplied with receiver unit. Connect blue wire from
receiver unit to the blue downlight wire using wire
connector supplied with receiver unit. Connect orange
wire from receiver unit to the orange uplight wire using
wire connector supplied with receiver unit. (Figure 3)
1. To set the code on receiver unit, slide dip switches to
the same positions as set on the remote. (Figure 1)
NOTE: The remote unit has 32 different code
combinations. To prevent possible interference from or to
other remote units, simply change the combination code
in the remote and receiver.
NOTE: Factory setting is all up. Do not use this position.
10
How to Wire Your Ceiling Fan
Green Wire
(Ground) from
Hanger Bracket
Green Wire
(Ground)
Green Wire
(Ground) from
Hanger Ball
Listed Outlet
Box
White
Black
Black
Blue
White
BLK-ANT
Black White
Orange
Household
Supply
to Downlight
to Motor
to Motor
to Uplight
4. Once the connection has been made, slide the
receiver into the hanger bracket, taking care not to
pinch the wires. (Figure 5)
How to Wire Your Ceiling Fan (continued)
Receiver
Hanger Bracket
11
How to Install Your Canopy Housing
2. Securely attach and tighten the canopy screw cover
over the shoulder screws in the hanger bracket utilizing
the keyslot twist-lock feature. (Figure 1b)
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed. (Figure 1a)
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and the
ceiling.
NOTE: This step is applicable after the neccessary wiring is completed.
Canopy Screw
Cover
How to Assemble Your Ceiling Fan Blades
Canopy
HARDWARE USED:
x 9
Figure 1
x 9
FIBER WASHER
1. Carefully slide the blade through the slot as shown.
Securely fasten the three blades with washer-head
screws with fiber washers. Do not over-tighten.
(Figure 1)
INSTALLATION NOTE
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled may
result in damage to the fan blades.
ʆ
WARNING
To reduce the risk of personal injury, do not bend the
blades when installing, balancing or cleaning the fan.
Do not insert foreign objects in between the rotating
blades.
WASHER HEAD
SCREWS
3/16ß-24
Ý:DVKHU+HDG
Screw with
)LEHU:DVKHUSHUEODGH
Figure 5
Figure 1a Figure 1b
12
How to Assemble Your Light Kit or Cap
Motor Assembly
Figure 1
1. Remove one of the three screws in the support
bracket at the bottom of the motor assembly. Retain
the screw for later and slightly loosen the remaining
two screws. (Figure 1)
2. Assemble the light kit to the support bracket using
the two key slots in the light kit. Replace the previously
removed screw and securely tighten all three screws.
(Figure 2)
3. Remove one of the three screws in the light kit.
Retain the screw for later and slightly loosen the
remaining two screws. (Figure 3)
Figure 4
Figure 5A
4. If installing the light kit, skip this step.
Assemble the light kit wire cover to the light kit using
the two key slots. Replace the removed screw and
secure all three screws. (Figure 4)
Light Kit
Figure 3
Motor
Assembly
Figure 2
Light Kit
Light Kit
Figure 5B
Connect the 2 single pin connectors from the LED
assembly to the 2 single pin connectors from motor
assembly. (Figure 5A)
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
CAUTION
5A. For use with light kit.
5B. For use with steel cap.
If you want to install the steel cap and not the light kit.
Assemble the steel cap to the light
kit
by twisting in
a clockwise direction. (Figure 5B)
NOTE:
If you have installed your fan with the steel
cap, skip Steps 6 and 7.
Light Kit Wire Cover
Steel Cap
Light Kit
LED
Assembly
How to Operate Your Ceiling Fan
2. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box. (Figure 2)
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until the blades are in place. Noise and
fan damage could result.
WARNING
Figure 2
MAIN FUSE BOX
1. IMPORTANT: Using a full range dimmer switch
(not included) to control fan speed will damage the fan.
To reduce the risk of fire or electrical shock, do not use
a full range dimmer switch to control the fan speed.
(Figure 1)
Figure 1
For illustrative purposes only-not
intended to cover all types of controls
WARNING
Do not operate this fan with a variable (Rheostat) wall
controller or dimmer switch. Doing so could result in
damage to the ceiling fan's remote control unit.
13
How to Assemble Your Light Kit or Cap (continued)
Figure 6
Figure 7
Light Kit
7. Secure the glass to light kit by twisting in a
clockwise direction. Do not over-tighten. (Figure 7)
6. Assemble the LED assembly to the light kit using
the two key slots. Replace the removed screw from
Step 3 and secure all three screws. (Figure 6)
The light source is designed for this specific
application and can overheat if serviced by untrained
personnel. If any servicing is required, the product
should be returned to an authorized service facility
for examination or repair.
CAUTION
Light Kit
LED Assembly
Glass
12V 23A
Battery (1 pcs)
Figure 3
Figure 4
Dip Switch
ON DIP
1 2 3 4 5
Remote
14
How to Operate Your Ceiling Fan (continued)
3. To make fan operational, install 23A/12V battery
(included) in hand-held remote transmitte
4. To set the remote code with a small screwdriver or
ball point pen (neither included), slide dip switches
firmly up or down. (Figure 4)
r, with fan
power off, then follow the remote code setting
process. (If not used for long periods of time, remove
battery to prevent damage to transmitter). Store the
remote away from excessive heat or humidly.
(Figure 3)
NOTE: The remote unit has 32 different code
combinations. To prevent possible interference from
or to other remote units, simply change the
combination code in the remote and receiver.
NOTE: Factory setting is all up. Do not use this
position.
Figure 5
5. Remote functions: (Figure 5)
Uplight button: Turns light on and off.
Downlight button: Turns light on and off.
How to Install Your Remote Control
15
How to Operate Your Ceiling Fan (continued)
1. Installing Wall Holder: (Figure 1)
Attach wall plate using the two provided screws.
Figure 7
7. If airflow is desired in the opposite direction, turn
the fan off and wait for the blades to stop turning.
, then slide the reverse switch to the opposite position
and turn fan on again. (Figure 7)
Reverse Switch Information
Season Rotation Direction Switch Position
Summer Counter-Clockwise
Right
Winter Clockwise
Left
Reversing
Switch
Maintenance
1. Periodic cleaning of your new ceiling fan is the only
maintenance that is needed. When cleaning, use
only a soft brush or lint free cloth to avoid
scratching the finish. Abrasive cleaning agents are
not required and should be avoided to prevent
damage to finish.
Do not use water when cleaning your ceiling fan.
It could damage the motor or the finish and create
the possibility of electrical shock.
CAUTION
Periodic light dusting of the blades is recommended.
A feather duster will work best.
How to Clean Your Ceiling Fan Blades
Avoid using water, cleansers, or harsh rags, which
can warp and ruin the finish.
Figure 1
16
Trouble Shooting
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
WARNING
Trouble Probable Cause Suggested Remedy
1.FAN WILL
NOT START
1. Check main and branch circuit fuses
or circuit breakers.
2. Check line wire connections to fan
and switch wire connections in the
switch housings.
CAUTION: Make sure main power is
turned off !
1. Fuse or circuit breaker blown.
2. Loose power line connections to the
fan, or loose switch wire connections
in the switch housing.
2.FAN SOUNDS NOISY
1. Attach blades to fan before operating.
2. Check to make sure all screws in
motor housing are snug (do not
overtighten).
3. Check to make sure wire connectors
in switch housing are not rattling
against each other or against the
interior wall of the switch housing.
CAUTION: Make sure main power is
turned off !
4. Some fan motors are sensitive to
signals from solid-state variable
speed controls. Solid-state controls
are not recommended, choose an
alternative control method.
1. Blades not attached to fan.
2. Loose screws in motor housing.
3. Wire connectors inside housing
rattling.
4. Motor noise caused by solid state
variable speed control.
3.FAN WOBBLES
EXCESSIVELY
1. Tighten both set screws securely in
downrod support.
2. Tighten the set screws in the downrod/
hanger ball assembly.
3. Tighten the hanger bracket screws to
the outlet box, and secure outlet box.
4. Balance blades using balance kit
provided in hardware bag.
1. Setscrew in downrod support is loose.
2. Setscrew in downrod/hanger ball
assembly is loose.
3. Hanger bracket and/or ceiling outlet
box is not securely fastened.
4. Fan blades out of balance.
4.NOT ENOUGH AIR
MOVEMENT
3. Dead battery in remote control. 3. Replace with new battery.
1. If possible, consider using a longer
downrod (not included, you can buy
the longer downrod from
fanimation.com).
4. Make sure reversing switch position is
all the way to one side.
4. Reversing switch in neutral position.
17
Parts List
Model No. LP8577**
Reference # Description Part #
1
ADRAC4GT1-45**
2
P827701**
3
4
APPCP1405** Motor Coupling Cover 5
AP827703**
AMA8577**
Blade Set
Motor Assembly
6
AP827706**
7
AP817710
Z0902
RECAN8577
APP799004BL
APPCP1101**
LED Assembly
Ligtht Kit/Glass Assembly
8
Light Kit Wire Cover
9
Hand-Held Remote
10
Receiver Unit
Steel Cap
TR500US
12
11
HDWLP8277**
14
——
Wire Connectors (4)
Loose Hardware Bag:
Blade Mounting Hardware Bag:
— 3/16Ý-24 Washer Head Screws(10)
Fiber Washer (10)
—
—
—
—
Balance Kit
—
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
Part Number
Part Description
Fan Model Number
Contact your retail store for repair parts.
Before discarding packaging material, be certain all parts have been removed.
** Insert FINISH CODES (Refer to fan model number located on downrod support)
Hanger Bracket Assembly
Hanger Ball/Downrod Assembly
Canopy
Canopy Screw Cover Assembly
13
AP837717**
18
Model LP8577**
Exploded-View Illustration
NOTE: The illustration shown is not to scale or its actual con guration may vary.
Product/parts are subject to change without notice.
Figure 1
UPRIGHT
™
14
14
1
2
3
4
5
6
7
14
89
10
11
12 13
Copyright 2018 Fanimation
2018/03 V.01
10983 Bennett Parkway
Zionsville, IN 46077
Phone: 888-567-2055
Outside U.S.: 317-733-4113
www.fanimation.com
FAX: 866-482-5215
ADJUNTE SU RECIBO AQUÍ Y REGISTRE SU VENTILADOR EN FANIMATION.COM
LEA Y GUARDE ESTAS INSTRUCCIONES
Peso neto 7.58 kg (16.71 lbs)
Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 1-888-567-2055, 8 a.m. - 5 pm, hora del Este, de
lunes - viernes.
Número de serie
Fecha de compra
MODELO #LP8577**
™
VENTILADOR DE TECHO UPRIGHT
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
Fanimation LP8577LBL Le manuel du propriétaire
- Catégorie
- Ventilateurs ménagers
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Fanimation FP8533PN Le manuel du propriétaire
-
-
Fanimation FP8003BPN Le manuel du propriétaire
-
-
-
-
