Omcan VP-CN-0971 Manuel utilisateur

Vacuum Packaging Machines

Models VP-CN-0971, 1220, 1060, 1273

Items 24081, 24082*, 24083*, 31824*

Instruction Manual

Revised - 10/15/2021

Toll Free: 1-800-465-0234

Fax: 905-607-0234

Email: [email protected]

www.omcan.com

*

2

Page

--------------------------------------------------------------------------- 3 - 4

--------------------------------------------------------------------------- 4 - 5

-------------------------------------------------------------------------- 6

-------------------------------------------------------------------------------------------- 6

--------------------------------------------------------------------------------------------- 7

----------------------------------------------------------------------------------- 8 - 11

----------------------------------------------------------------------------- 11 - 12

---------------------------------------------------------------------------- 13 - 15

---------------------------------------------------------------------------- 16

------------------------------------------------------------------------------------------- 17 - 18

---------------------------------------------------------------------------- 19

Table of Contents

Section

General Information

Safety and Warranty

Technical Specications

Installation

Operation

Maintenance

Troubleshooting

Parts Breakdown

Electrical Schematics

Notes

Warranty Registration

Model VP-CN-0971 / Model VP-CN-1220

Model VP-CN-1060 / Model VP-CN-1273

3

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan

and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or

negligent use of this equipment. The product shall only be operated by someone over the age of 18, of

sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct

operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the

machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of

the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the

external packaging, open carton to ensure all ordered items are within the box, and there is no concealed

damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),

please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may

initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety

instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save

these instructions for future reference. Also save the original box and packaging for shipping the

equipment if servicing or returning of the machine is required.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et

Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne

ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de

plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour

utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication

de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine

ou des personnes à proximité de la machine pendant son fonctionnement.

VÉRIFIEZ LE COLIS DÈS RÉCEPTION

Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage

n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés

sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises

manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant

d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager

une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine

doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents

d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli

par un tiers transporteur.

4

Safety and Warranty

1. Before operation, please read through the user guide about each operation rules and safety precaution.

2. You must ll the vacuum pump with pump oil before use (when the machine is placed at a horizontal

position, the oil should keep at 1/3-1/2 of the oil window). When running, the oil level should not be lower

than 1/3 of the oil window. Do not ll with too much oil to avoid over ow.

3. The machine should be placed horizontally in good ventilation and light without corrosive gas and heavy

dust.

4. The power connection position may be located on a different side, be sure that there is proper grounding

General Information

Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations

et les consignes de sécurité.

Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces

instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour

l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba

Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona

inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona

mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido

entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.

Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la

máquina mientras esta en el funcionamiento.

REVISE EL PAQUETE A SU LLEGADA

Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el

empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la

caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes

o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro

de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre

los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se

muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron

a recoger por terceros.

Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de

funcionamiento y seguridad.

Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para

salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el

envío del equipo si servicio técnico o devolución de la máquina que se requiere.

5

Safety and Warranty

protection before use.

5. Always ensure top cover is open before turning the power on. Start the machine by pressing the top cover

and the process start automatically. For 3-Phase units, please be sure the vacuum pump is running in the

correct direction. If the direction is wrong, simply switch the phase of the power.

6. Preheat of vacuum pump must be done in low temperature working area. Turn off the heater selection

switch at the control panel to off position. This is to prevent heating process and cut down wear and tear

losses.

Note: Do not block the air hole in the chamber.

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure

or other damages resulting from installation in non-commercial or residential applications. The right

is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as

possible.

1 YEAR PARTS AND LABOUR WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized

service technician to repair the equipment locally.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not

improper use.

Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components are classied as normal solid urban waste and can therefore be disposed of

without difculty.

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated

waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

6

Technical Specications

Installation

Model VP-CN-0971 VP-CN-1220 VP-CN-1060 VP-CN-1273

Power 1.2 HP / 0.9 kW 1.47 HP / 1.1 kW

Seal Bar (16.5” x 0.31”) x 2

(419 x 8mm) x 2

15.7” x 0.31”

399 x 8mm

(20.5” x 0.31”) x 2

(521 x 8mm) x 2

Cycle Time 23 seconds 26 seconds 25 seconds 28 seconds

Pump Power 20 m³/h 45 m³/h

Chamber

Size

17.3” x 16.5” x 3”

439 x 419 x 76mm

23” x 16.5” x 4”

584 x 419 x 102mm

17” x 16.5” x 6”

432 x 419 x 152mm

21.3” x 20.5” x 6”

541 x 521 x 152mm

Approximate

Capacity 26.5 lbs. / 12 kgs. 66.1 lbs. / 30 kgs. 55.1 lbs. / 25 kgs. 77.2 lbs. / 35 kgs.

Electrical 220V / 60Hz / 3 110V / 60Hz / 1 220V / 60Hz / 3

Dimensions 22” x 18.7” x 39”

559 x 475 x 991mm

28.5” x 19” x 38”

724 x 483 x 965mm

22” x 18.7” x 41”

559 x 475 x 1041mm

26.8” x 23.2” x 37.8”

681 x 589 x 960mm

Weight 176 lbs. / 79.8 kgs. 200.8 lbs. / 91.1 kgs. 187 lbs. / 84.8 kgs. 253 lbs. / 114.8 kgs.

Packaging

Dimensions

25” x 20.5” x 40”

635 x 521 x 1016mm

30” x 22” x 44”

762 x 559 x 1118mm

24” x 21” x 47”

610 x 533 x 1194mm

29” x 27” x 45”

737 x 686 x 1143mm

Packaging

Weight 220 lbs. / 99.8 kgs. 252 lbs. / 114.3 kgs. 211 lbs. / 95.7 kgs. 366 lbs. / 166 kgs.

Item Number 24081 24082 24083 31824

Please set every parameter before starting the machine.

1. Turn on the power supply, check through the settings on the panel and make sure “--” must be show after

setting is done, otherwise operation of this machine cannot be conducted.

2. Press the setting button, the indicator lamp of vacuum lights to enter into the setting state of vacuum timing.

Press the upward or downward key to increase or decrease vacuum time in the range of 0-99 seconds.

3. Press the setting button, sealing indicator lamp lights to enter the sealing setting state. Press the upward or

downward key to increase or decrease sealing time in the range of 0-3.5 seconds.

4. Press the setting button, cooling indicator lamp lights to enter the cooling setting state. Press the upward or

downward key to increase or decrease cooling time in the range of 0-9.9 seconds.

5. After the cooling time is set, press the setting button to nish parameter setting and “ED” is shown on the

panel.

6. Press the sealing temperature button, temperature indicator lamp lights to enter the temperature setting

state. You may choose between high temperature, middle temperature and low temperature.

7

Operation

1. Turn on the power supply and select a suitable vacuum packaging bag for the product.

2. Set the processing parameter and select the sealing temperature, see installation.

3. Place the vacuum bag in the chamber with the opening end on top of the sealing bar. Clamp it with

pressing stick.

4. Close the acrylic cover and the machine will complete the procedure automatically.

5. During processing, the vacuum chamber will form a vacuum self-lock state, the whole heating and sealing

procedure are completed in a vacuum environment and the LED display shows the ow process.

6. When the vacuum indicator on the panel lights, the equipment is under vacuum state, the LED display

shows the vacuum time and will automatically enter the next work state when the time completes.

7. When the sealing indicator on the panel lights, the equipment is under sealing state, the LED display shows

the sealing time and will automatically enter the next work state when the time completes.

8. According to the time setting, the machine doesn’t act when cooling, the panel shows “□□” till the timing is

nished, air is returned, the cover opens automatically, and the whole process is nished. Then prepare the

next cycle.

Note: Press the E-Stop button in the event of unexpected issue during operation.

NOTE

• Disconnect from power supply when not in use.

• Do not run machine without vacuum bags.

8

Maintenance

FILLING THE OIL

Remove the rear board and unscrew the bottom board to drain the old oil. Once drained, screw the bottom

board back then unscrew the oil lling section, use a bottle to ll with the new oil and screw closed. See the

below examples of locations for the oil tank.

NOTE: FILL WITH NEW FOOD GRADE OIL.

9

Maintenance

REPLACING THE SEALING TAPE AND HEATING WIRE

1. Disconnect the cable from the pin, then pick the complete sealing bar up from the vacuum chamber.

2. Remove the pressing stick from the complete sealing bar by cross screwdriver, then remove the stainless

steel base.

3. Pull the plastic parts out from the two sides of the sealing bar by hand, then tear off the sealing tape.

4. Remove the forcing screws from the two sides of the sealing bar with an Allen Key, then remove the

heating wire.

10

Maintenance

5. Put one side of a new heating wire into the fastener groove and tighten it with the Allen Key.

6. Put the other side of the heating wire into the other side fastener groove, then screw it with the Allen Key.

7. Fasten the heating wire, then cut the excess heating wire.

8. Take the new sealing tape at a proper length and stick it on the heating wire.

9. Cut the remaining sealing tape on the ends to allow them to fold over.

11

Maintenance

Troubleshooting

10. Put plastic clamps on the sides of the sealing bar.

11. Install the stainless steel base and pressing stick.

12. Connect the cable of the complete sealing bar to the pin, then put the sealing bar back in the vacuum

chamber to complete the installation.

Problem Cause Solution

Vacuum pump does not work. Limit switch is not pressed on. Close the machine cover and

adjust the limit switch.

Limit switch is broken. Replace.

Contactor is broken. Replace.

Pump motor is broken. Replace.

12

Troubleshooting

Vacuum chamber cannot reach the

vacuum degree.

The vacuum pump is worn or

damaged.

Replace.

Loose air pipe joint, broken pip,

damaged sealing ring of vacuum

chamber or damaged valve.

Tighten or replace.

Insufcient oil in vacuum pump. Add more oil.

Vacuum time is not enough. Increase the vacuum time.

Cover cannot be opened. Air release valve is not turned on. Turn on the air release valve.

Air remains in bag after operation

is nished.

Wrong position resting on sealing

bar.

Reposition.

Pressing stick presses the bag

open.

Replace the pressing stick.

Abnormal sound or tripping when

running, black smoke or oil drop.

Abnormal sound of fan of pump

motor.

Call Omcan.

Blockage in air intake and/or pip. Unblock.

Insufcient oil, or non standard oil

used.

Add more oil, or replace with food

grade oil.

Overheating of pump. Lessen the operating time.

Faulty vacuum pump motor or

valve of vacuum pump.

Replace.

Not able to seal. The temperature is not selected. Select the temperature.

The heating wire is damaged or

connecting wire is cut off.

Replace the wire or reconnect.

The sealing time is at 0. Increase the sealing time.

The relay is damaged. Replace the relay.

The sealing valve does not

operate.

Call Omcan.

Uneven sealing veins, air bubbles,

or not sealing properly.

Silicon sealer is dirty. Clean the sealer.

Sealing time is too short. Increase sealing time.

Temperature is too low. Increase the temperature.

Cooling time insufcient. Increase the cooling time.

Sealing tape is damaged. Replace the sealing tape.

13

Parts Breakdown

Model VP-CN-0971 24081

Model VP-CN-1220 24082

Model VP-CN-1060 24083

Model VP-CN-1273 31824

14

Parts Breakdown

Model VP-CN-0971 24081

Model VP-CN-1220 24082

Item No. Description Position Item No. Description Position Item No. Description Position

AE448 Lid for 24081 1 AE454 Vacuum Meter for 24081 11 AE466 Gas Flushing Valve for 24081 24

AE449 Lid Gasket for 24081 2 AE462 Fan for 24081 13 AE470 Sealing Transformer for 24081 25

AE450 Sealing Gasket for 24081 3 AE463 Gas Connect Port for 24081 16 AE458 Assemble Valve for 24081 27

AE451 Sealing Fabric (10m/Roll) for 24081 4 AE467 Circuit Breaker for 24081 17 AE459 Vacuum Pump for 24081 28

AE452 Sealing Tape for 24081 5 AE464 Power Socket for 24081 18 AE457 Filter for 24081

AE156 Assemble Sealing Bar for 24081 6 AE460 Lid Hinge for 24081 19 AE465 Power Switch for 24081

AE453 Gas Bag for 24081 7 AE461 Lid Switch for 24081 20 AE471 PP Plate for 24081

AE455 Plastic Frame for 24081 9 AE469 Working Transformer for 24081 21 AG793 Power Cord for 24081

AE456 Control Panel for 24081 10 AE468 Relay Cards for 24081 23

Item No. Description Position Item No. Description Position Item No. Description Position

AE472 Lid for 24082 1 AE479 Vacuum Meter for 24082 11 AE491 Gas Flushing Valve for 24082 24

AE473 Lid Gasket for 24082 2 AE487 Fan for 24082 13 AE495 Sealing Transformer for 24082 25

AE474 Sealing Gasket for 24082 3 AE488 Gas Connect Port for 24082 16 AE483 Assemble Valve for 24082 27

AE475 Sealing Fabric (10M/Roll) for 24082 4 AE492 Circuit Breaker for 24082 17 AE484 Vacuum Pump for 24082 28

AE476 Sealing Tape for 24082 5 AE489 Power Socket for 24082 18 AE482 Filter for 24082

AE477 Assemble Sealing Bar for 24082 6 AE485 Lid Hinge for 24082 19 AE490 Power Switch for 24082

AE478 Gas Bag for 24082 7 AE486 Lid Switch for 24082 20 AE496 PP Plate for 24082

AE480 Plastic Frame for 24082 9 AE494 Working Transformer for 24082 21 AG794 Power Cord for 24082

AE481 Control Panel for 24082 10 AE493 Relay Cards for 24082 23

15

Parts Breakdown

Model VP-CN-1060 24083

Model VP-CN-1273 31824

Item No. Description Position Item No. Description Position Item No. Description Position

AE497 Lid for 24083 1 AE504 Vacuum Meter for 24083 11 AE516 Gas Flushing Valve for 24083 24

AE498 Lid Gasket for 24083 2 AE512 Fan for 24083 13 AE520 Sealing Transformer for 24083 25

AE499 Sealing Gasket for 24083 3 AE513 Gas Connect Port for 24083 16 AE508 Assemble Valve for 24083 27

AE500 Sealing Fabric (10M/Roll) for 24083 4 AE517 Circuit Breaker for 24083 17 AE509 Vacuum Pump for 24083 28

AE501 Sealing Tape for 24083 5 AE514 Power Socket for 24083 18 AE507 Filter for 24083

AE502 Assemble Sealing Bar for 24083 6 AE510 Lid Hinge for 24083 19 AE515 Power Switch for 24083

AE503 Gas Bag for 24083 7 AE511 Lid Switch for 24083 20 AE521 PP Plate for 24083

AE505 Plastic Frame for 24083 9 AE519 Working Transformer for 24083 21 AG795 Power Cord for 24083

AE506 Control Panel for 24083 10 AE518 Relay Cards for 24083 23

Item No. Description Position Item No. Description Position Item No. Description Position

AE522 Lid for 31824 1 AE528 Vacuum Meter for 31824 11 AE540 Gas Flushing Valve for 31824 24

AE523 Lid Gasket for 31824 2 AE536 Fan for 31824 13 AE544 Sealing Transformer for 31824 25

AE524 Sealing Gasket for 31824 3 AE537 Gas Connect Port for 31824 16 AE532 Assemble Valve for 31824 27

AE525 Sealing Fabric (10m/Roll) for 31824 4 AE541 Circuit Breaker for 31824 17 AE533 Vacuum Pump for 31824 28

AE526 Sealing Tape for 31824 5 AE538 Power Socket for 31824 18 AE531 Filter for 31824

AC190 Complete Sealing Bar for 31824 6 AE534 Lid Hinge for 31824 19 AE539 Power Switch for 31824

AE527 Gas Bag for 31824 7 AE535 Lid Switch for 31824 20 AE545 PP Plate for 31824

AE529 Plastic Frame for 31824 9 AE543 Working Transformer for 31824 21 AG796 Power Cord for 31824

AE530 Control Panel for 31824 10 AE542 Relay Cards for 31824 23

16

Electrical Schematics

Model VP-CN-0971 24081

Model VP-CN-1220 24082

Model VP-CN-1060 24083

Model VP-CN-1273 31824

17

Notes

________________________________________________________________________________________

18

Notes

________________________________________________________________________________________

19

Warranty Registration

Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,

cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:

Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la

carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at

the perforation and then send to the address specied below. You can also register online by visiting:

OMCAN

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

https://omcan.com/warranty-registration/

or email to: [email protected]

Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Would you like to extend the warranty? Yes No



Por correo en Canadá

Pour postale au Canada

For mailing in Canada

Por correo en los EE.UU.

Pour diffusion aux États-Unis

For mailing in the US

OMCAN

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

Niagara Falls, New York

USA, 14305

Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North

American food service industry. Our success over these many years can be attributed to our commitment

to strengthen and develop new and existing relationships with our valued customers and manufacturers.

Today with partners in North America, Europe, Asia and South America, we continually work to improve

and grow the company. We strive to offer customers exceptional value through our qualied local sales

and service representatives who provide convenient access to over 5,000 globally sourced products.

Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et

matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces

nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles

et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en

Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et

développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à

nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000

produits provenant du monde entier.

Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros

de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir

a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos

clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan

continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor

excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un

fácil acceso a más de 5,000 productos con origen a nivel mundial.

Omcan VP-CN-0971 Manuel utilisateur

Omcan VP-CN-0971 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents