Magtek DynaPro Go Manuel utilisateur

DynaPro Go
Magtek
Marque
Magtek
Modèle
DynaPro Go
Taper
Manuel utilisateur
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200135 rev rev 60 3/19
DynaPro Go
Handheld PIN Pad Device with
MSR/Contact/Contactless
Quick Installation Guide
Installing DynaPro Go: Conguration is done prior to deployment for the certicate authority public
keys and terminal and payment brand settings; end users need only set up a host with appropriate
software, congure the software, and connect the device to the host.
DynaPro Go
Works with Operating Systems
USB Hosts: Windows 7, Windows 8 and 8.1, Windows 10,
Android 4.4.2 and above with USB OTG support
802.11 wireless TLS 1.2 hosts: iOS 7.1 and above, Android 6.0
and above, Windows 7 SP1 and above
Bluetooth LE hosts: iOS 7.1 and above, Android 5.0 and above,
Windows 8.1 and above on hosts that support Bluetooth LE
Secure Connections per Bluetooth Core Specication 4.2.
Controls
In any solution, DynaPro Go is connected to a host, which must have software installed that knows
how to communicate with the device, and which is capable of processing transactions.
To set up the host to work with DynaPro Go, follow the installation and conguration instructions
provided by the vendor of the host or the host software.
Technical Support contact [email protected]
When contacting the support team make sure the device is charged, and have the part number
and serial number(s) available. Installation and Operationa Manual can be found on magtek.com
under support.
MagTek
recommends
charging atleast
every 6 months
to maximize
operation.
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200135 rev 60 3/19
Charging the Device
DynaPro Go’s power comes from an on-board rechargeable battery when it is not connected to a
host’s USB port. The battery must be periodically recharged by connecting it to a charging cradle, a
USB port, or a stand-alone USB charger. Charging the device requires a micro-USB cable 6 feet (1.8
Meter) maximum length to ensure proper battery charging.
To charge the device in the charging cradle for power only (no USB communication):
1. Connect the charging cradle to a USB port or to a USB charger.
2. Place the device in the charging cradle with the charging contacts pointing into the charging
cradle and the LCD display facing front.
Both the charging cradle and the device require a USB power supply that can provide at least
500mA @ 5V.
MAGTEK RECOMMENDS CHARGING ATLEAST EVERY
6 MONTHS TO MAXIMIZE OPERATION.
DynaPro Go’s Lithium Polymer (LiPo) battery may be charged from MagTek’s charging cradle or a
USB charger until the device’s battery indicator shows maximum charge has been reached. The
device will stop charging its battery automatically.
Contents/Pre-Installation Checklist
Major components of DynaPro Go are shown in Figure 1. In addition to the components shown,
the device has a tamper trigger recessed in the bottom that is intended for manufacturer use only.
DO NOT INSERT ANYTHING INTO THE TAMPER TRIGGER HOLE! DOING SO WILL ERASE ALL INJECTED KEYS;
THE DEVICE WILL STOP FUNCTIONING, AND WILL HAVE TO BE RETURNED TO THE MANUFACTURER FOR RE-
CONFIGURATION.
Figure 1. Major Components Diagram
Figure 2.
Device in Optional Charging cradle
Figure 3. USB connection
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200135 rev rev 60 3/19
On and Off
To power on the device: Press and hold the Power button for one second. Upon powering up, it will
display the “Welcome” screen and the current device status.
To power off the device: Press and hold the Power button for seven seconds, or press the Power
button for two seconds to display a “Power Off?” screen with a Yes / No selection above the left and
right function keys. To power off, press the function key below Yes. To cancel powering off and return
to the Welcome screen, either wait 10 seconds or press the function key below No. While the device
is powering off, the display shows “Powering off…” for three seconds before the display goes blank.
LCD Display
The device’s LCD display uses a backlight and can be congured to either remain at a constant user
selected brightness level (Manual mode) or adapt its brightness to ambient lighting based on the de-
vice’s light sensor (Auto mode). The factory default of the device is Manual mode at 75% brightness.
To change the LCD display backlight mode, press Left Function key 5, 2, 2, Right Function key to
open the LCD Brightness Cong screen. To exit without saving changes, press the Cancel key or wait
10 seconds for the device to return to the Welcome screen.
USB Connection
To connect DynaPro Go to a host computer or charger using the Micro USB port, follow these steps:
• Connect the small end of the USB cable to DynaPro Go as shown in Figure 3.
• Connect the large end of the USB cable to the charger or to the host computer’s USB port.
As soon as DynaPro Go starts receiving power through USB, it will automatically power on. If DynaPro
Go is not automatically recognized you may need to unplug and plug it in again.
Wireless (Wi-Fi) connection
• Make sure the wireless access point, network, device, and host are set up properly and
tested. Check IP address registration on DHCP server, check wireless MAC addresses as
listed devices, and check rewalls for communication. Provide the wireless access point SSID
and passcode to the advanced operator who will congure the devices.
• Power on the device and make sure the device is congured to use the 802.11 wireless
connection. DynaPro Go supports multiple connection types, but only one interface can
be active at a time. To change the active connection, on the Welcome screen, press Left
Function Key 4 5 6 Right Function Key to show a conrmation screen to begin using the
currently inactive connection type.
• Make sure the device is connected to the wireless network by checking the status icons. See
Installation and Operation Manual for complete details.
Bluetooth LE
• To connect DynaPro Go to a host via the Bluetooth LE connection, follow these steps:
• Make sure the host supports Bluetooth LE Secure Connections.
• Install host software for DynaPro Go and power on the device.
• Check DynaPro Go Bluetooth LE active connection.
• Press Left Function Key 1 2 3 Right Function Key to enable pairing requests.
• Scan for Bluetooth devices on host and select.
• Host and Device show 6-digit matching passcode.
• Accept pairing on device and host.
• Check pairing by checking the device’s status icons.
• Check the installation and Operation Manual for further details and troubleshooting.
Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200135 rev 60 3/19
Compliance
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate this equipment.
CUR/UR
This product is recognized per Underwriter Laboratories and
Canadian Underwriter Laboratories 1950.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio
noise from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits
radioélectriques dépassant les limites applicables aux appareils
numériques de la classe B prescrites dans le Réglement
sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740 p 562-546-6400 | f 562-546-6301 | www.magtek.com
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformé à la norme
NMB-003 du Canada.
IC: 23169-30056216
Contains Transmitter module IC: 10147A-362
CE STANDARDS
Testing for compliance with CE requirements was performed
by an independent laboratory. The unit under test was found
compliant with standards established for Class B devices.
UL/CSA
This product is recognized per UL 60950 1, 2nd Edition, 2011
12 19 (Information Technology Equipment - Safety - Part 1:
General Requirements), CSA C22.2 No. 60950 1 07, 2nd
Edition, 2011 12 (Information Technology Equipment - Safety -
Part 1: General Requirements).
ROHS STATEMENT
When ordered as RoHS compliant, this product meets the
Electrical and Electronic Equipment (EEE) Reduction of
Hazardous Substances (RoHS) European Directive 2002/95/EC.
The marking is clearly recognizable, either as written words like
“Pb-free,” “lead-free,” or as another clear symbol ( ).
PCI DEVICE VALIDATION
Compare the hardware ID (HW ID) on the printed label and the
firmware ID (FW IDs), accessible via the device and displayed on
the screen, to the hardware # and firmware # posted on the PCI
compliance web page: https://www.pcisecuritystandards.org/
assessors_and_solutions/pin_transaction_devices
Search for MagTek and find the product name, DynaPro Go, on
the web page. Compare the Hardware # and Firmware #.
Pb
Declaration of Conformity
RF Frequencies and Power
802.11 Wireless:
Average Power Radiated: 1.02mW (0.08 dBm)
Conducted Power = 97.7mW (19.89 dBm)
Frequency range 2400 MHz to 2497 MHz
Contactless Reader:
Radiated Power: 10.34dBm
Frequency range: 13.553 MHz to 13.567MHz
Hereby, MagTek Inc. declares that the radio equipment types Wideband Transmission System (802.11 wireless) and Non-Specic
Short Range Device (contactless) are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.magtek.com/Content/DocumentationFiles/D998200238.pdf
Important Health and Safety Information
The device implements electronic labels (“e-labels”) that report its Health and Safety certification information. To access them, press
the sequence Left Function key, 7, 8, 0, Right Function key. This brings up a page with indicators on the bottom that show more
information is available by scrolling. Press Left Function key and Right Function key to scroll to the previous and next e-label. To return
to the Welcome screen, press the Cancel key, or wait 10 seconds. For further instructions please reference Installation and Operation
Manual (D998200129).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Magtek DynaPro Go Manuel utilisateur

DynaPro Go
Magtek
Marque
Magtek
Modèle
DynaPro Go
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents