© 2015 Hatco Corporation
GLO-RAY
®
Heated Stone Shelves
Plaques chauffantes en pierre
GRSS, GRSSB, GRSSR Series/Série
Installation and Operating Manual
Manuel d'installation et d'utilisation
I&W 07.05.166.00
Register Online!
(see page 2)
S'inscrire en ligne!
(voir page 19)
hatcocorp.com
Do not operate this equipment unless you
have read and understood the contents of
this manual! Failure to follow the
instructions contained in this manual may
result in serious injury or death. This
manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en este
manual puede resultar en un serio lesión
o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted no
puede entender el contenido de este
manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel !
Le non-respect des instructions
contenues dans ce manuel peut entraîner
de graves blessures ou la mort. Ce
manuel contient des informations
importantes concernant l'entretien,
l'utilisation et le fonctionnement de ce
produit. Si vous ne comprenez pas le
contenu de ce manuel, veuillez le signaler
à votre supérieur. Conservez ce manuel
dans un endroit sûr pour pouvoir vous y
référer plus tard.
Français = p 19
WARNING
ADVERTENCIA
AVERTISSEMENT
2
Form No. GRSSM-0615
English
INTRODUCTION
The Hatco Glo-Ray
®
Heated Stone Shelf is designed to keep
prepared foods hot while blending into your décor. Heated
Stone Shelves will keep all foods at optimum serving
temperatures without affecting quality. These warmers have a
thermostatically-controlled heated base to extend the holding
times of most foods.
Glo-Ray Heated Stone Shelves are a product of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly prior
to shipment.
This manual provides the installation, safety, and operating
instructions for the Glo-Ray Heated Stone Shelf. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of the Glo-Ray Heated Stone Shelf.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
NOTICE
CAUTION
WARNING
Important Owner Information ..............................................2
Introduction...........................................................................2
Important Safety Information...............................................3
Model Descriptions...............................................................4
Model Designation................................................................4
Specifications........................................................................5
Plug Configurations.............................................................5
Electrical Rating Charts.......................................................5
Dimensions .........................................................................7
Installation.............................................................................9
General ...............................................................................9
GRSS and GRSSR Models ................................................9
GRSSB Models...................................................................9
Operation .............................................................................11
General..............................................................................11
Maintenance ........................................................................12
General .............................................................................12
Daily Cleaning...................................................................12
Cleaning the Stone Surface ..............................................12
Troubleshooting Guide ......................................................13
Options and Accessories...................................................14
Limited Warranty.................................................................18
Authorized Parts Distributors............................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label on bottom of GRSS model, bottom of control box on
GRSSB and GRSSR models). Please have this information
available when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. ________________________________________
Voltage __________________________________________
Date of Purchase __________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Business
Hours: 7:00
AM to 5:00 PM Central Standard Time (CST)
(Summer Hours: June to September—
7:00
AM to 5:00 PM CST Monday–Thursday
7:00
AM to 4:00 PM CST Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: part[email protected]
Fax: 800-690-2966 (Parts and Service)
414-671-3976 (International)
Additional information can be found by visiting our web site at
www.hatcocorp.com.
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
CONTENTS
Form No. GRSSM-0615
3
English
IMPORTANT SAFETY INFORMATION
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Remote mounted control enclosure must be mounted
on a vertical wall and installed in vertical position.
Mounting control enclosure in horizontal position may
result in collection of liquids and lead to an electric
shock.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
Make sure food product has been heated to the proper food-
safe temperature before placing on the unit. Failure to heat
food product properly may result in serious health risks. This
unit is for holding preheated food product only.
WARNING
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
BURN HAZARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Do not operate built-in models without the trim mounting
ring and the control box mounted properly as described in
the installation instructions.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Make sure to clean and sanitize stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
caused by heat generated from Hatco equipment is not
covered under the Hatco warranty. Verify with the
manufacturer that the material is suitable for prolonged
temperatures up to 200°F (93°C).
Built-in units must not have a setpoint temperature higher
than 200°F (93°C). Temperatures exceeding 200°F (93°C)
will damage unit and void warranty.
Do not modify wiring or cut thermostat capillary on control
box to increase remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing off.
If weight on shelf exceeds 50 lbs. (23 kg), a deflection up to
5/32″ (4 mm) is possible. If weight on shelf exceeds 100 lbs.
(45 kg), a deflection of 1/4″ (6 mm) is possible. Shelf is not
guaranteed if weight on shelf exceeds 150 lbs. (68 kg). All
weight must be distributed evenly across entire shelf.
NOTICE
CAUTION
WARNING
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
MODEL DESIGNATION
4
Form No. GRSSM-0615
MODEL DESCRIPTIONS
English
All Models
All Hatco Glo-Ray
®
Heated Stone Shelves are ideal for pass
through areas, buffet lines, and as hors d’ oeuvre displays. The
unique Heated Stone Shelf is constructed of a simulated stone
solid surface and is available in several colors. Standard
equipment includes an illuminated Power I/O (on/off) switch, a
thermostatically-controlled heated stone top, and painted steel
base.
GRSS Models
The GRSS Heated Stone Shelf is a portable shelf with an
attached 6′ (1829 mm) cord and plug. The portable unit is
available in six models: GRSS-2418, GRSS-3018, GRSS-3618,
GRSS-4818, GRSS-6018, and GRSS-7218.
Model GRSS
GRSSR Models
The GRSSR Heated Stone Shelf is a portable round shelf with
an attached 6′ (1829 mm) cord and plug. The portable unit is
available in three models: GRSSR-16, GRSSR-18 and
GRSSR-20.
Model GRSSR
GRSSB Models
The GRSSB Heated Stone Shelf is a built-in unit that is
equipped with an attached trim mounting ring. The unit includes
a remote control box that is attached with 3′ (914 mm) of
conduit. A 6′ (1829 mm) power cord with plug connects the
remote control box to the power source.
The built-in units are available in six models: GRSSB-2418,
GRSSB-3018, GRSSB-3618, GRSSB-4818, GRSSB-6018, and
GRSSB-7218.
Model GRSSB
NOTE: Refer to the OPTIONS AND ACCESSORIES section in
this manual for the available options and accessories.
G R S S X - X X X X
Glo-Ray
Heated Shelf
Stone
Model Distinction
None = Portable Rectangular
R = Portable Round
B = Built-In Rectangular
Width/Diameter of Shelf
Depth of Shelf
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSS-2418 120 635 5.3 NEMA 5-15P 27 lbs. (12 kg)
220–230 (CE) 534–583 2.4–2.5 CEE 7/7 Schuko 27 lbs. (12 kg)
230–240 (CE) 583–635 2.5–2.6 BS-1363 27 lbs. (12 kg)
GRSS-3018 120 780 6.5 NEMA 5-15P 30 lbs. (14 kg)
220–230 (CE) 655–716 3.0–3.1 CEE 7/7 Schuko 30 lbs. (14 kg)
230–240 (CE) 716–780 3.1–3.3 BS-1363 30 lbs. (14 kg)
GRSS-3618 120 930 7.8 NEMA 5-15P 35 lbs. (16 kg)
220–230 (CE) 782–854 3.6–3.7 CEE 7/7 Schuko 35 lbs. (16 kg)
230–240 (CE) 854–930 3.7–3.9 BS-1363 35 lbs. (16 kg)
GRSS-4818 120 1270 10.6 NEMA 5-15P 45 lbs. (20 kg)
220–230 (CE) 1068–1166 4.8–5.0 CEE 7/7 Schuko 45 lbs. (20 kg)
230–240 (CE) 1166–1270 5.0–5.2 BS-1363 45 lbs. (20 kg)
GRSS-6018 120 1560 13.0 NEMA 5-20P 56 lbs. (25 kg)
220–230 (CE) 1310–1432 6.0–6.2 CEE 7/7 Schuko 56 lbs. (25 kg)
230–240 (CE) 1432–1560 6.2–6.6 BS-1363 56 lbs. (25 kg)
GRSS-7218 120 1860 15.6 NEMA 5-20P 68 lbs. (31 kg)
220–230 (CE) 1564–1708 7.2–7.4 CEE 7/7 Schuko 68 lbs. (31 kg)
230–240 (CE) 1708–1860 7.4–7.8 BS-1363 68 lbs. (31 kg)
Form No. GRSSM-0615
5
SPECIFICATIONS
English
Plug Configurations
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P NEMA 5-20P
CEE 7/7 Schuko BS-1363
Plug Configuration
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage, size,
and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: Specification label on bottom of GRSS model, bottom
of control box on GRSSB and GRSSR models. See
label for serial number and verification of unit electrical
information.
WARNING
Electrical Rating Chart — GRSS Models
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSSB-2418 120 635 5.3 NEMA 5-15P 30 lbs. (14 kg)
220–230 (CE) 534–583 2.4–2.5 CEE 7/7 Schuko 30 lbs. (14 kg)
230–240 (CE) 583–635 2.5–2.6 BS-1363 30 lbs. (14 kg)
GRSSB-3018 120 780 6.5 NEMA 5-15P 35 lbs. (16 kg)
220–230 (CE) 655–716 3.0–3.1 CEE 7/7 Schuko 35 lbs. (16 kg)
230–240 (CE) 716–780 3.1–3.3 BS-1363 35 lbs. (16 kg)
GRSSB-3618 120 930 7.8 NEMA 5-15P 40 lbs. (18 kg)
220–230 (CE) 782–854 3.6–3.7 CEE 7/7 Schuko 40 lbs. (18 kg)
230–240 (CE) 854–930 3.7–3.9 BS-1363 40 lbs. (18 kg)
GRSSB-4818 120 1270 10.6 NEMA 5-15P 51 lbs. (23 kg)
220–230 (CE) 1068–1166 4.8–5.0 CEE 7/7 Schuko 51 lbs. (23 kg)
230–240 (CE) 1166–1270 5.0–5.2 BS-1363 51 lbs. (23 kg)
GRSSB-6018 120 1560 13.0 NEMA 5-20P 56 lbs. (25 kg)
220–230 (CE) 1310–1432 6.0–6.2 CEE 7/7 Schuko 56 lbs. (25 kg)
230–240 (CE) 1432–1560 6.2–6.6 BS-1363 56 lbs. (25 kg)
GRSSB-7218 120 1860 15.6 NEMA 5-20P 70 lbs. (32 kg)
220–230 (CE) 1564–1708 7.2–7.4 CEE 7/7 Schuko 70 lbs. (32 kg)
230–240 (CE) 1708–1860 7.4–7.8 BS-1363 70 lbs. (32 kg)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRSSR-16 120 250 2.1 NEMA 5-15P 14 lbs. (6 kg)
100 180 1.8 NEMA 5-15P 14 lbs. (6 kg)
220–230 (CE) 190–220 0.8–0.9 CEE 7/7 Schuko 14 lbs. (6 kg)
230–240 (CE) 220–250 0.9–1.0 BS-1363 14 lbs. (6 kg)
GRSSR-18 120 325 2.7 NEMA 5-15P 16 lbs. (7 kg)
100 230 2.3 NEMA 5-15P 16 lbs. (7 kg)
220–230 (CE) 265–295 1.2–1.3 CEE 7/7 Schuko 16 lbs. (7 kg)
230–240 (CE) 295–325 1.3–1.4 BS-1363 16 lbs. (7 kg)
GRSSR-20 120 400 3.3 NEMA 5-20P 18 lbs. (8 kg)
100 270 2.7 NEMA 5-15P 18 lbs. (8 kg)
220–230 (CE) 330–370 1.5–1.6 CEE 7/7 Schuko 18 lbs. (8 kg)
230–240 (CE) 370–400 1.6–1.7 BS-1363 18 lbs. (8 kg)
6
Form No. GRSSM-0615
SPECIFICATIONS
English
Electrical Rating Chart — GRSSR Models
Electrical Rating Chart — GRSSB Models
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
Model Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
GRSS-2418
24″
(610 mm)
18″
(457 mm)
2-1/2″
(64 mm)
19-3/4″
(502 mm)
13-3/4″
(349 mm)
GRSS-3018
30″
(762 mm)
18″
(457 mm)
2-1/2″
(64 mm)
25-3/4″
(654 mm)
13-3/4″
(349 mm)
GRSS-3618
36″
(914 mm)
18″
(457 mm)
2-1/2″
(64 mm)
31-3/4″
(806 mm)
13-3/4″
(349 mm)
GRSS-4818*
48″
(1220 mm)
18″
(457 mm)
6-1/4″
(159 mm)
42-3/4″
(1086 mm)
12-3/4″
(324 mm)
GRSS-6018*
60″
(1524 mm)
18″
(457 mm)
6-1/4″
(159 mm)
54-3/4″
(1391 mm)
12-3/4″
(324 mm)
GRSS-7218*
72″
(1828 mm)
18″
(457 mm)
6-1/4″
(159 mm)
66-3/4″
(1695 mm)
12-3/4″
(324 mm)
Form No. GRSSM-0615
7
SPECIFICATIONS
English
Dimensions — GRSS Series
A
D E
B
C
Front View Side View
Dimensions—GRSS Model
* Height includes 4″ (102 mm) legs.
Width
(D)
Depth
(E)
Height
(F)
Remote Box
(Standard)
7″
(178 mm)
3″
(76 mm)
3-1/4″
(83 mm)
Model
Diameter
(A)
Height
(B)
GRSSR-16
16″
(406 mm)
2-5/8″
(67 mm)
GRSSR-18
18″
(457 mm)
2-5/8″
(67 mm)
GRSSR-20
20″
(508 mm)
2-5/8″
(67 mm)
Model
Width
(A)
Depth
(B)
Height
(C)
GRSSB-2418
25-5/8″
(651 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
GRSSB-3018
31-5/8″
(803 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
GRSSB-3618
37-5/8″
(956 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
GRSSB-4818
49-5/8″
(1260 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
GRSSB-6018
61-5/8″
(1565 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
GRSSB-7218
73-5/8″
(1870 mm)
19-5/8″
(498 mm)
2-1/4″
(57 mm)
8
Form No. GRSSM-0615
SPECIFICATIONS
English
Dimensions
—GRSSB Model
A
B
Top View Side View
Dimensions—GRSSR Model
Dimensions — GRSSR Models
Dimensions — GRSSB Models
A
B
D
E
C
F
Front View
Side View
NOTE: See the OPTIONS ANDACCESSORIES section for
dimension information for flush-style remote mounted
control enclosures.
Refer to the INSTALLATION section of this manual for
actual countertop cutout dimensions.
NOTICE
Form No. GRSSM-0615
9
INSTALLATION
English
General
Use the following procedures to install the GRSS, GRSSR, and
GRSSB units.
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate the unit indoors where the ambient air temperature
is a minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
GRSS and GRSSR Models
1. Remove the unit from the box.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces of
unit.
NOTE: If 4″ (102 mm) legs are required, refer to the OPTIONS
AND ACCESSORIES section in this manual for
installation instructions. 4″ legs are included with
models greater than 36″ (914 mm) in width.
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F (21°C).
Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, and exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
4. Install any accessories that came with the unit. Refer to the
OPTIONS AND ACCESSORIES section for details.
WARNING
CAUTION
NOTICE
GRSSB Models
1. Remove the unit from the box.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape and protective packaging from all surfaces
of unit.
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
caused by heat generated from Hatco equipment is not
covered under the Hatco warranty. Verify with the
manufacturer that the material is suitable for prolonged
temperatures up to 200°F (93°C).
3. Prepare the countertop opening. Refer to the “GRSSB
Countertop Cutout Chart” in this section for recommended
countertop cutout dimensions.
4. Apply a bead of National Sanitation Foundation (NSF)-
approved sealant on the top edge of the countertop cutout
and the underside of the trim mounting ring. The sealant
must be rated for use at a minimum temperature of 250° F
(121° C).
5. Place the unit into the countertop opening.
6. Remove any excess sealant.
7. Locate the remote control box assembly in an area that is
convenient for operation. If desired or necessary, the
control box can be mounted in a semi-remote location.
• Remove the control box from the bottom of the unit.
• If necessary, remove the end brackets from the control
box, rotate/reposition, and re-secure to the control box.
• The control box can be panel, surface, or under counter
mounted.
• The distance the control box can be mounted from the unit
is determined by the 3’ (914 mm) conduit (optional conduit
lengths of 6’ [1829 mm] and 10’ [3048 mm] are also
available with electronic controls). Do not pull the conduit
tight to increase the mounting distance. The conduit
should have some slack after the control box is mounted.
NOTE: The remote control box should be mounted using
screws with a 1/4″ (6 mm) minimum diameter screw
head inserted through the keyholes located on the
mounting brackets. The remote control box is to be
readily removable—not permanently mounted.
...continued
NOTICE
GRSSB Countertop Cutout Chart
Model Width Depth
GRSSB-2418 24-5/8″ (625 mm) – 24-7/8″ (632 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
GRSSB-3018 30-5/8″ (778 mm) – 30-7/8″ (784 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
GRSSB-3618 36-5/8″ (930 mm) – 36-7/8″ (937 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
GRSSB-4818 48-5/8″ (1235 mm) – 48-7/8″ (1241 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
GRSSB-6018 60-5/8″ (1540 mm) – 60-7/8″ (1546 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
GRSSB-7218 72-5/8″ (1845 mm) – 72-7/8″ (1851 mm)
18-5/8″ (473 mm) – 18-7/8″ (479 mm)
10
Form No. GRSSM-0615
INSTALLATION
English
Trim Mounting Ring
Countertop
Apply a bead of NSF-approved
sealant between the countertop
material and trim mounting ring.
Sealant must be rated for use at
a minimum temperature of
250° F (121° C).
GRSSB Built-In Installation
GRSSB Built-In Installation
Control Box Mounting Options
Panel
U
nder Counter
Surface
7-1/4″
(184 mm)
7″
(178 mm)
3″
(76 mm)
3-1/4″
(83 mm)
Do not modify wiring or cut thermostat capillary on control
box to increase remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
8. Once all components are secured, proceed to the
OPERATION section.
NOTE: A 6′ (1829 mm) cord is supplied with this unit; any
excess cord should be routed neatly so it does not hang
down.
NOTICE
Form No. GRSSM-0615
11
General
Use the following procedure to turn on and operate the GRSS,
GRSSR, and GRSSB units.
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Startup
1. Clean and sanitize the stone surface using a clean, damp
cloth and a sanitizer approved for food contact surfaces.
2. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size, and plug configuration. See
SPECIFICATIONS section in this manual for details.
3. Move the Power I/O (on/off) switch to the I (on) position.
BURN HAZARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
WARNING
CAUTION
Power I/O (on/off) Switch
Temperature Control
Standard Control Panel—GRSS Model
4. Turn the Temperature Control to the desired temperature
setting.
• Turning the Temperature Control knob clockwise will
increase the temperature setting. Turning the
Temperature Control knob counterclockwise will
decrease the temperature setting.
5. Allow the unit 30 minutes to reach operating temperature.
NOTE: Refer to the OPTIONS AND ACCESSORIES section
for installation and operation information for GRSSB
units equipped with a flush-style remote mounted
control panel.
If weight on shelf exceeds 50 lbs. (23 kg), a deflection up to
5/32″ (4 mm) is possible. If weight on shelf exceeds
100 lbs. (45 kg), a deflection of 1/4″ (6 mm) is possible. Shelf
is not guaranteed if weight on shelf exceeds 150 lbs. (68 kg).
All weight must be distributed evenly across entire shelf.
NOTICE
OPERATION
English
12
Form No. GRSSM-0615
MAINTENANCE
English
General
Hatco Glo-Ray
®
Heated Stone Shelves are designed for
maximum durability and performance, with minimum
maintenance.
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
1. Before turning on the unit each day, clean and sanitize the
stone surfaces using a clean, damp cloth and a sanitizer
approved for food contact surfaces. If additional cleaning is
necessary, refer to the “Cleaning the Stone Surface”
information in this section.
2. At the end of each day:
a. Turn off the unit and allow to cool.
b. Wipe down all metal surfaces using a clean, damp, non-
abrasive cloth.
c. Clean and sanitize the stone surfaces using a clean,
damp cloth and a sanitizer approved for food contact
surfaces. If additional cleaning is necessary, refer to the
“Cleaning the Stone Surface” information in this section.
NOTE: To correct inconsistent staining and discoloration, refer
to the “Cleaning the Stone Surface” information in this
section.
d. Wipe dry with a clean, non-abrasive cloth.
WARNING
NOTICE
Cleaning the Stone Surface
Proper use of the products listed below will not damage the
stone surface (follow the directions on the product labels).
NOTE: Stone surfaces are a simulated stone solid surface.
Make sure to clean and sanitize stone surface properly after
deep cleaning the surface using abrasives and before
placing food product on unit.
Hard to Remove Stains
For hard-to-remove stains, use the supplied abrasive pad along
with an abrasive cleaner such as Ajax, Comet, Bon Ami, or Bar
Keeper’s Friend. Additional abrasive pads are available from
Hatco (P/N 04.39.049.00). NOTICE: Use supplied abrasive
pad on stone surface only.
NOTE: Do not use steel wool or metal scouring pads.
Mineral Based Stains
For a mineral-based stain, cleaners designed to remove iron or
rust are recommended and should not harm the stone surface.
Scratches
For scratches, use sandpaper starting with the coarsest grit and
going to finest grit until the scratch disappears. Blend area in with
the supplied abrasive pad.
CAUTION
Symptom Probable Cause Corrective Action
Unit too hot. Temperature Control set too high. Change the temperature setting to a lower
setting.
Unit plugged into incorrect power supply. Verify with qualified personnel that power
supply matches unit specification.
Temperature Control defective. Contact Authorized Service Agent or Hatco for
assistance.
Unit not hot enough. Temperature Control set too low. Change the temperature setting to a higher
setting.
Location of unit is susceptible to air currents
(air conditioning ducts or exhaust fans).
Block air currents or relocate unit.
Unit not working at all. Unit not plugged in. Plug unit into proper power supply.
Unit not turned on. Move Power I/O (on/off) switch to the I (on)
position.
Power ON/OFF (I/O) switch defective. Contact Authorized Service Agent or Hatco for
assistance.
Temperature Control defective. Contact Authorized Service Agent or Hatco for
assistance.
Base heating element burned out. Contact Authorized Service Agent or Hatco for
assistance.
Stone surface material is
stained, discolored, or has
inconsistent staining/discoloration.
Stone surface is not being cleaned properly. Clean surface using the “Cleaning the Stone
Surface” information in the MAINTENANCE
section of this manual. If these methods fail to
produce acceptable results, contact Hatco for
assistance.
Shelf is flexing. Excessive weight on shelf. Distribute weight evenly on entire shelf. If
weight on the shelf exceeds 50 lbs. (23 kg), a
deflection up to 5/32″ (4 mm) is possible. If
weight on the shelf exceeds 100 lbs. (45 kg), a
deflection of 1/4″ (6 mm) is possible. The shelf
is not guaranteed if weight on shelf exceeds
150 lbs. (68 kg).
Form No. GRSSM-0615
13
TROUBLESHOOTING GUIDE
English
This unit must be serviced by trained and qualified
personnel only. Service by unqualified personnel may lead
to electric shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
WARNING
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com and click on
Find Service Agent, or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: p[email protected]
Fax: 800-690-2966 or 414-671-3976
14
Form No. GRSSM-0615
OPTIONS AND ACCESSORIES
English
4″ Adjustable Legs (GRSS Model)
Use the following procedure to install 4″ (102 mm) adjustable
legs in place of the rubber feet on a GRSS unit.
NOTE: 4″ (102 mm) legs are included with models greater than
36″ (914 mm) in width.
ELECTRIC SHOCK HAZARD: Turn power switch OFF, un-
plug power cord, and allow unit to cool before performing
any maintenance or cleaning.
Do not lay unit on the side with the control panel or dam-
age to unit could occur.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Carefully turn the unit upside down and lay the unit on a flat
surface. Make sure to cover the surface with something to
prevent scratching the stone surface.
3. At each corner of the base, remove the foot screw and
rubber foot.
Installing the 4″ Legs
4. At each corner of the base, screw a 4″ leg into the bottom
of the base.
Note: The feet on the 4″ legs are adjustable for leveling the
unit. Use a 5/8″ (16 mm) open-end wrench to make
leveling adjustments once the unit is placed in its final
position.
WARNING
NOTICE
4″ Leg
Handles (GRSS Models only)
Designer black powdercoated rounded stainless steel handles
are available for GRSS models.
The handles are field retrofittable and are installed onto each
end of the unit using the following procedure.
On each end of the unit:
1. Remove the three nuts located on the underside of the
stone surface support ring.
2. Align the three holes on the handle with the three studs on
the support ring, and position the handle on the studs.
3. Replace the three nuts onto the studs, and tighten securely.
Handle Installation
Recessed Top for GRSSB Models
An optional recessed top is available for GRSSB models. Units
with a recessed top allows the heated surface to sit lower than
countertop surface.
Handle
Support
Ring
Nut
Stud
Form No. GRSSM-0615
15
OPTIONS AND ACCESSORIES
English
Model
Width
(A)
Depth
(B)
GRSSR-16
17″
(432 mm)
11-3/4″
(298 mm)
GRSSR-18
19″
(483 mm)
13-3/4″
(349 mm)
GRSSR-20
21″
(533 mm)
15-3/4″
(400 mm)
Cutting Board (GRSSR Models only)
The cutting board comes equipped with rubber feet on the
bottom to center it on the unit.
The cutting board is made of the same material as the heated
stone surface and is available in the same colors.
Cutting Board
Cutting Board Dimensions
Risers (GRSSR Models only)
Steel risers are available to increase the height of GRSSR units.
They are available in 3″ (76 mm) and 5″ (127 mm) heights in
several colors and in stainless steel.
To install the riser:
1. Place the riser in the desired location on the countertop.
2. Thread the power cord of the GRSSR unit through one of
the access holes in the riser.
3. Set the GRSSR unit inside the riser. Make sure the controls
are accessible through the access holes in the riser.
Model GRSSR 5” (127 mm) Riser
Access Hole
A
B
Cutting Board Dimensions
16
Form No. GRSSM-0615
OPTIONS AND ACCESSORIES
English
Remote Mounted Control Enclosures
(GRSSB Models only)
Two flush-style remote mounted control enclosures are
available for the GRSSB model — the Mechanical Temperature
Control enclosure and the Digital Temperature Controller
enclosure. Both enclosures are installed using the following
procedure.
ELECTRIC SHOCK HAZARD: Remote mounted control
enclosure must be mounted on a vertical wall and installed
in vertical position. Mounting control enclosure in
horizontal position may result in collection of liquids and
lead to an electric shock.
Install remote mounted control enclosure outside of heat
zone. Locating control enclosure inside heat zone will
cause control(s) to overheat, malfunction, and fail.
Do not modify wiring or cut thermostat capillary on control
box to increase remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
NOTE: A qualified electrician is recommended for connecting
the units to a power source.
1. Prepare cutout and pre-drill screw holes.
2. Remove trim cover from control enclosure assembly.
3. Position control enclosure into opening through the
backside.
4. Secure control enclosure to mounting surface using screws
(not supplied).
5. Connect proper power source to the mounted remote
control enclosure.
6. Reinstall trim cover.
NOTE: Units are equipped with a 3′ (914 mm) flexible conduit
connecting the control enclosure to the unit. The digital
temperature controller also offers 6′ (1829 mm) and 10′
(3048 mm) conduit lengths.
WARNING
NOTICE
Power I/O (on/off) Switch
Both flush-style remote mounted control enclosures are
equipped with a Power I/O (on/off) switch. Move the Power I/O
(on/off) switch to the I (on) position to turn on the unit. The
indicator light in the switch glows when the unit is on.
Changing the Setpoint Temperature — Mechanical
Temperature Control
Turn the temperature control clockwise to increase the setpoint
temperature. Turn the temperature control counterclockwise to
decrease the setpoint temperature.
Mechanical Temperature Control
Temperature
Control
Power I/O (on/off) Switch
Optional Remote Mounted Control Enclosure Installation Dimensions
Mechanical Temperature Control
4″ (102 mm)
Digital Temperature Controller
4-3/4″ (121 mm)
Mounting Surface
Trim Cover
Control Enclosure
5-7/8″
(149 mm)
3-7/8″
(98 mm)
6-3/8″
(162 mm)
6-7/8″
(174 mm)
Side View of Installed EnclosureFront View of Cutout
IMPORTANT NOTE:
Make sure the installation
location provides enough
room for electrical
connections to the control
enclosure.
Form No. GRSSM-0615
17
OPTIONS AND ACCESSORIES
English
Changing the Setpoint Temperature — Digital
Temperature Controller
Units equipped with a digital temperature controller will heat up
to the setpoint temperature automatically when they are turned
on. Use the following procedure to change the setpoint
temperature.
Built-in units must not have a setpoint temperature higher
than 200°F (93°C). Temperatures exceeding 200°F (93°C)
will damage unit and void warranty.
NOTE: The temperature shown on the display may be
inaccurate when unit temperature is below 130°F (54°C).
1. Press the key three times. The current setpoint
temperature will be shown on the TEMPERATURE display
(“SP” will be displayed after the second press).
2. Press the key or key within 10 seconds to change
the setpoint temperature.
3. Press the key to lock in the new setpoint temperature.
The TEMPERATURE display will go blank for two seconds
to show that the new setting has been accepted.
NOTE: After 10 seconds of inactivity during the programming
process, the controller will exit programming mode
automatically without saving any changes.
Digital Temperature Controller
SET Key
Up Arrow
Key
Down
Arrow
Key
Display
NOTICE
Changing Fahrenheit and Celsius Setting — Digital
Temperature Controller
Use the following procedure to change between Fahrenheit
and Celsius on the display.
1. Press the key once. Either an “F” for Fahrenheit or “C”
for Celsius will be displayed.
2. Press the key or key within 10 seconds to change
between “F” (Fahrenheit) and “C” (Celsius).
3. Press the key three times to lock in the new setting.
The TEMPERATURE display will go blank for two seconds
to show that the new setting has been accepted.
NOTE: After 10 seconds of inactivity during the programming
process, the controller will exit programming mode
automatically without saving any changes.
18
Form No. GRSSM-0615
LIMITED WARRANTY
English
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions or
18 months from the date of shipment from Hatco. Buyer must
establish the Product’s purchase date by registering the
Product with Hatco or by other means satisfactory to Hatco in
its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
c) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
d) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.
Without limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light
tubes, glass components, and fuses; Product failure in booster
tank, fin tube heat exchanger, or other water heating equipment
caused by liming, sediment buildup, chemical attack, or
freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will be
limited solely, at Hatco’s option, to repair or replacement using
new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by Hatco or a Hatco-authorized service agency.
Hatco will not accept the return of any Product without prior
written approval from Hatco, and all such approved returns shall
be made at Buyer’s sole expense. HATCO WILL NOT BE
LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM THE USE OF OR INABILITY TO USE THE
PRODUCTS OR FROM THE PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OTHER PRODUCT OR GOODS.
Formulaire n° GRSSM-0615
19
Français
Informations Importantes pour le Propriétaire .....................19
Introduction.........................................................................19
Consignes de Sécurité Importantes .................................20
Description du Modèle .......................................................21
Désignation du Modèle ......................................................22
Caractéristiques Techniques.............................................22
Configuration des Fiches ..................................................22
Tableau des valeurs nominales électriques......................22
Dimensions .......................................................................24
Installation...........................................................................26
Modèles GRSS et GRSSR ...............................................26
Modèles GRSSB...............................................................26
Mode d'emploi.....................................................................28
Généralités........................................................................28
Maintenance ........................................................................29
Généralités........................................................................29
Nettoyage quotidien ..........................................................29
Nettoyer la surface en pierre ............................................29
Guide de Dépannage..........................................................30
Options et accessoires ......................................................31
Garantie Limitée..................................................................34
Autorisés Distributeurs de Pièces........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension et la
date d'achat de l'appareil dans les espaces ci-dessous (étiquette
des caractéristiques techniques en dessous du modèle GRSS et
en dessous du boîtier de commande des modèles GRSSB et
GRSSR). Veuillez avoir cette information à portée de la main si
vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage __________________________________________
Date d’achat ______________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards pour
faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant Parts
& Service, puis cliquez sur Warranty Registration.
Horaires
ouvrables: 7h00 à 17h00
Heure du Centre des États-Unis (CST)
(Horaires d’été : juin à septembre—
7h00 à 17h00 CST du lundi au jeudi
7h00 à 16h00 CST le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: part[email protected]
Télécopieur: 800-690-2966 (Pièces et Service après-vente)
414-671-3976 (Internationale)
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
INTRODUCTION
La plaque chauffante en pierre Glo-Ray
®
de Hatco est conçue
pour conserver la nourriture préparée au chaud tout en se
fondant dans votre décor. Les plaques chauffantes en pierre
garderont tous les aliments à une température de service
optimale sans nuire à leur qualité. Elles comportent une base
chauffante contrôlée par un thermostat afin de prolonger les
temps de conservation de la plupart des plats.
Les plaques chauffantes en pierre Glo-Ray sont des produits
issus d'une recherche approfondie et d'essais sur le terrain. Les
matériaux utilisés ont été sélectionnés pour un maximum de
durabilité, d'aspect esthétique et de performance optimum.
Chaque appareil est minutieusement inspecté et testé avant
expédition.
Ce manuel fournit les instructions d'installation, de sécurité et
d'utilisation des plaques chauffantes en pierre. Hatco vous
recommande de lire l’ensemble des instructions d’installation,
de sécurité et de fonctionnement contenues dans ce manuel
avant d’installer et d’utiliser l'appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT indique une situation dangereuse qui, si
elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
AVERTISSEMENT
ATTENTION
AVIS
SOMMAIRE
20
Formulaire n° GRSSM-0615
CONSIGNES DE SÉCURITÉ IMPORTANTES
Français
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Le boîtier de commande monté à distance peut être
installé sur un mur vertical en position verticale.
L'installation du boîtier de commande en position
horizontale peut conduire à une accumulation de
liquides et entraîner une décharge électrique.
• Mettez l'unité hors tension depuis l'interrupteur,
débranchez le cordon d'alimentation et laissez l'unité
refroidir avant d'effectuer tout nettoyage, tout réglage
ou tout entretien.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Ne pas utiliser l’appareil si le cordon est endommagé ou
usé.
• Ne pas tirer l’appareil par son cordon électrique.
• Ne pas tenter de réparer ni de changer un cordon élec-
trique endommagé. Ce cordon doit être changé par
Hatco, par un réparateur Hatco agréé ou par une per-
sonnes de qualifications comparables.
• Utilisez uniquement des pièces de rechange d'origine
Hatco lorsque l'entretien est nécessaire. Utilisez des
pièces détachées Hatco authentiques sous peine
d'annuler toutes les garanties et d'exposer l’utilisateur
à des tensions électriques dangereuses pouvant
entraîner une électrocution ou des brûlures. Les pièces
de rechange authentiques Hatco sont spécifiées pour
fonctionner en toute sécurité dans les environnements
dans lesquels elles sont utilisées. Certaines pièces de
rechange génériques ou d'après-vente n'ont pas les
caractéristiques qui leur permettent d'opérer en toute
sécurité dans les équipements Hatco.
DANGER D’INCENDIE : Placez l'unité à au moins 25 mm
(1″) de murs ou de matières inflammables. Si ces distances
de sécurité ne sont pas respectées, une décoloration ou
une combustion peut se produire.
Hatco Corporation n'est pas responsable de la température
réelle à laquelle les aliments sont servis. Il est de la
responsabilité de l'utilisateur de s'assurer que les produits
alimentaires sont maintenus et servis à une température
sans danger.
Assurez-vous que tous les opérateurs ont été formés à
l'utilisation sûre et correcte de l'appareil.
AVERTISSEMENT
S'assurer que la nourriture a été chauffée à une
température adaptée à une alimentation saine avant de la
placer sur l'appareil. Le non-chauffage des aliments à une
température appropriée peut poser un grand risque pour
la santé. Cet appareil n'est destiné qu'à maintenir des
aliments préchauffés au chaud.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l'écart de l'appareil.
La réparation de cet appareil doit être confiée
exclusivement à du personnel qualifié. Les réparations par
des personnes non qualifiées peuvent provoquer des
décharges électriques et des brûlures.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
+1 800-558-0607 ou +1 414-671-6350 ; télécopieur
+1 800-690-2966; télécopieur internationale +1 414-671-3976.
DANGER DE BRÛLURE : Certaines surfaces extérieures de
l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placez l'unité à une hauteur adaptée au comptoir, à un
emplacement pratique à utiliser. L'emplacement doit être
plan pour éviter que l'unité ou son contenu ne tombe
accidentellement, et suffisamment solide pour supporter
le poids de l'unité et de son contenu.
Ne pas utiliser les modèles intégrés si la bordure de montage
et le boîtier de commande ne sont pas correctement installés
comme décrit dans les instructions d'installation.
La National Sanitation Foundation (NSF) exige que les
appareils de plus de 914 mm (36″) de large ou pesant plus de
36 kg (80 lb) soient fixés sur ou surélevés par rapport à la
surface d'installation. Si l'appareil ne peut pas être fixé sur
l'emplacement d'utilisation, des pieds de 102 mm (4″) sont
fournis pour permettre le nettoyage en dessous de l'appareil.
S'assurer de nettoyer et de désinfecter correctement la
surface en pierre après avoir nettoyé la surface en
profondeur avec des abrasifs et avant de placer des
aliments sur l'appareil.
L'appareil est conçu et recommandé pour fonctionner posé
sur un comptoir en métal. La garantie Hatco ne couvre pas
les dommages faits au comptoir. Pour les autres surfaces,
vérifiez auprès de leurs fabricants que le matériau peut
supporter de façon durable des températures atteignant
93 °C (200 °F).
Les appareils intégrés ne doivent pas atteindre un point de
consigne de température supérieur à 93 °C (200 °F). Les
températures dépassant les 93 °C (200 °F) endommagent
l'appareil et annulent la garantie.
ATTENTION
AVIS
AVERTISSEMENT
Lisez l'information de securite importante suivante avant d'utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d'endommager l'équipement ou la propriété.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Hatco GRSS-3618 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: Hatco GRSS-3618 Owner's manual
Documents connexes
-
Hatco GRSSR-DL77516 Series Le manuel du propriétaire
-
-
-
-
-
-
-
Hatco GRAIH, GRAIHL Series Le manuel du propriétaire
-
-