EcoSmart CB QC MEDLRG Manuel utilisateur

Marque: EcoSmart

Modèle: CB QC MEDLRG

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

INSTALLATION INSTRUCTIONS & HOME OWNERS MANUAL

ECO 8 | ECO 11 | ECO 18 | ECO 24 | ECO 27 | ECO 36

IMPORTANT SAFETY INFORMATION

When installing or using any high voltage electrical appliance, basic safety precautions should always be

followed. Under no circumstance should you attempt to clean, install, inspect, repair, disassemble or

otherwise service this water heater, without first shutting off all power to the unit directly at the circuit

breaker box. SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

THIS PRODUCT SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN AND A QUALIFIED PLUMBER IN

ACCORDANCE WITH ALL NATIONAL, STATE, PROVINCIAL AND LOCAL ELECTRICAL & PLUMBING CODES.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY AND COMPLETELY PRIOR TO INSTALLATION & USE.

FAILURE TO DO SO COULD CAUSE PROPERTY DAMAGE, SERIOUS INJURY, OR DEATH.

This manual should be given to the homeowner after installation and should be retained for future reference.

Tested and certified by the Water Quality Association against NSF/ANSI 372 for lead free

compliance.

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

DANGER!

WATER TEMPERATURE SAFETY SETTING

Safety and energy conservation are factors to be considered when selecting the

water temperature setting of water heater’s thermostat. Water temperatures

above the 125°F can cause severe burns or death from scalding. Be sure to read

and follow the warnings outlined on the label pictured below. This label is also

located on the water heater near the thermostat access panel.

Notice: Mixing valves are recommended for reducing

point of use water temperature by mixing hot and cold

water in branch water lines. It is recommended that a

mixing valve complying with the Standard for

Temperature Actuated Mixing Valves for Hot Water

Distribution Systems, ASSE 1017 be installed.

The chart shown above may be used as a guide in

determining the proper water temperature for your

home.

DANGER: Households with small children,

disabled, or elderly persons may require a 120°F or lower

thermostat setting to prevent contact with “HOT” water.

The temperature of the water in the heater is regulated

by the electronic control on the front of the water

heater. To comply with safety regulations, the

thermostat was set at 120°F before the water heater was

shipped from the factory.

Please consult Section 10

to learn more about setting

your heaters temperature.

Rotate right for higher

temperature (up to 140F)

or rotate left for cooler

temperature (as low as

80F) will be displayed on

the screen above the knob.

ABOUT YOUR TANKLESS WATER HEATER

Congratulations on the purchase of your Electric Tankless Water Heater! You have purchased the most

technologically-advanced electric tankless water heater on the market today.

Your new electric tankless water heater features advanced water flow rate and temperature sensors designed to

modulate power to the heating elements to maintain a precise user-selected output water temperature

between 80°F and 140°F (subject to incoming water temperature and power of the selected model).

To get the best performance and energy savings from your electric tankless water heater, it is important that it

be installed in accordance with our instructions and the electrical and plumbing codes applicable to your area,

and that you read this manual thoroughly for important operating instructions and tips.

If you have questions at any time, please contact us directly at:

EcoSmart Green Energy Products

400 Captain Neville Drive, Waterbury, CT 06705

Toll Free: 1-877-474-6473

Support@EcoSmartUS.com

CONTENTS

1. BEFORE INSTALLATION

2. SELECTING A LOCATION TO INSTALL

3. MOUNTING YOUR WATER HEATER

4. PLUMBING INSTALLATION

5. ELECTRICAL INSTALLATION

6. SIZING GUIDE

7. GENERAL OPERATING INSTRUCTIONS

8. MAINTENANCE

9. TROUBLE SHOOTING GUIDE

10. USER INTERFACE

1- BEFORE INSTALLATION

PLEASE READ THESE INSTRUCTIONS THOROUGHLY AND COMPLETELY PRIOR TO INSTALLATION & USE.

FAILURE TO FOLLOW INSTRUCTIONS COULD CAUSE PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR

DEATH.

By installing this product, you acknowledge the terms of the manufacturer’s warranty. Once the heater is

installed, do not return product to the place of purchase. If you have any questions regarding the warranty or

product return policies, please contact EcoSmart at 1-877-474-6473.

Inspect all components. The contents of your box should include one of the following units:

 ECO 8

 ECO 11

 ECO 18

 ECO 24

 ECO 27

 ECO 36

2- SELECTING A LOCATION TO INSTALL

This product is designed to be installed indoors only. You may install your unit in an outdoor location so long as

it is mounted in a suitable enclosure that protects it from rain, splashed water, direct sunlight, debris, and

insects.

DO NOT install this product in a location where it may be subjected to freezing temperatures. If the water inside

your tankless water heater freezes, it can cause severe and permanent damage that is not covered under your

warranty.

DO NOT locate the water heater in a location that is difficult to access.

Make sure that the water heater and hot water outlet pipe are out of reach of children so they are unable to

tamper with the temperature controls or injure themselves by touching the hot water outlet pipe. The outlet

water pipe can get very hot.

This product does NOT require venting.

Avoid installing your tankless water heater in a location prone to excessive humidity, moisture, or dust, or in an

area where it may be splashed with water or other liquids. DO NOT install under water pipes or air conditioning

lines that might leak or condense moisture that could then drip onto the heater. DO NOT install above electrical

boxes or junctions.

CAUTION: The water heater should not be located in an area where leakage will result in damage to the area

adjacent to it or to lower floors of the structure. Where such areas cannot be avoided, it is recommended that

a suitable catch pan, adequately drained, be installed under the water heater.

3- MOUNTING YOUR WATER HEATER

Your tankless water heater should be secured to the mounting surface with 4 screws (minimum 1-inch long)

using the built-in mounting brackets on each side of the heater. Make sure that the mounting surface is solid

and secure, and ensure that the unit is level prior to securing the screws. For ease of installation and servicing,

we recommend that this product be installed in an upright position with the inlet and outlet water connections

at the bottom of the unit for the ECO 18, ECO 24, ECO 27, and ECO 36, and with the inlet and outlet water

connections on the left and right sides of the unit for the ECO 8 and ECO 11.

Recommended Clearances: 12 inches above and below the heater

6 inches in front of and to the sides of the heater

CAUTION: Combustible materials should be kept at least 24 inches away from your water heater and the hot

water outlet pipe.

4- PLUMBING INSTALLATION

Please follow all plumbing instructions carefully. We recommend that this product be installed by a licensed and

qualified plumber in accordance with all applicable national, state, provincial, and local plumbing codes.

Installation Instructions

STEP 1: Connect the HOT WATER line to the water heater OUTLET located on the left side of the heater when

facing unit. Connect the COLD WATER line to the water heater marked INLET on the right side when facing unit.

STEP 2: After tightening both fittings at the water heater, open several hot water faucets and allow water to run

though the water heater for at least 2 to 3 minutes. This process purges all the air from the water lines and

MUST be performed prior to turning on the power at the unit. FAILURE TO FOLLOW THIS STEP CAN CAUSE

PERMANENT DAMAGE TO THE HEATING ELEMENTS. If any maintenance is performed on the water heater or the

home’s plumbing system that may introduce air into the plumbing pipes, it is important to turn the power off to

the water heater and purge the air out of the lines before allowing the unit to power up.

STEP 3: Carefully inspect all connections, unions, and the pressure relief valve (if installed) for leaks.

IMPORTANT NOTES:

1. Do not solder any pipes with unit connected to pipes – heat from soldering may damage the flow

sensor. Doing so will void the warranty.

2. This automatic tankless water heater is equipped with both computer-controlled and electro-

mechanical auto resetting thermostat switches for high-limited temperature protection. Since this

product does not use a storage tank, the use of a temperature pressure relief valve (T&P) is not required

for most installations. UL Standard 499 does NOT require that a pressure relief valve be used. However,

a T&P valve may be required to meet installation codes in your area. If one is required, install the

pressure relief valve in accordance with local codes and ensure that it operates correctly and that air is

purged from the valve prior to installing the water heater. When connecting to Flex or High

Temperature CPVC pipe, we recommend that a T&P valve be used for added safety.

Please note: Installations in the Commonwealth of Massachusetts and State of Kentucky require a

pressure relief valve. Please check your local installation codes for any special requirements.

3. The maximum operating water pressure is 150 PSI. If the water pressure is higher, a pressure reducing

valve must be installed on the main incoming water supply line prior to installing the electric tankless

water heater.

4. Flexible water heater hoses are recommended to be used with your water heater as part of the

installation. When connecting the inlet water pipe to the unit, make sure to use a wrench to hold the

unit’s connection, and another wrench to tighten, so that the flow sensor on the unit will not be

loosened or damaged. Serious internal damage to the water heater can occur if the inlet or outlet

connections are over tightened or if solder connections were made.

5. We recommend that a manual shut-off valve (ball valve) is installed on the inlet and outlet of the water

heater so that there is a convenient shut-off point available in the event that future maintenance or

servicing is required. It is extremely important to flush the lines to eliminate all plumbing paste or

residue in the lines caused by any welding or soldering before connecting pipes to the water heater.

We recommend that all the water pipes or hoses within 3 feet of the inlet and outlet connections be rated for

high temperature applications with a 150°F minimum.

5- ELECTRICAL INSTALLATION

EcoSmart recommends that this product be installed by a licensed and qualified electrician in accordance with

all applicable national, state, provincial, and local electrical codes. As with all electrical appliances, under no

circumstances should you attempt to install, repair or disassemble this water heater without first shutting off all

power to the unit directly at the fuse or breaker box. Make sure to shut off all breakers. SERIOUS BODILY

INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

All wiring (wire gauge) and circuit protection (breakers) must comply with the U.S. National Electrical Code (NEC)

in the USA, or the Canadian Electrical Code (CEC) in Canada. Failure to do so could result in property damage

and/or personal injury, and void your warranty. Note: The Canadian Electrical Code generally requires that all

supply wires and corresponding circuit protection used for domestic hot water heating and hydronic heating

applications be sized to a minimum of 125% of the maximum current rating of the heater (see model

specifications below for details).

Before installing this product, ensure that the home has sufficient electrical power available to handle the

maximum amperage load of the applicable model.

IMPORTANT NOTES:

Model ECO 8 and ECO 11 require 1 set of wire and ground (see wiring diagram)

Model ECO 18 requires 2 sets of wire and ground (see wiring diagram)

Model ECO 24 and ECO 27 require 3 sets of wire and ground (see wiring diagram)

Model ECO 36 requires 4 sets of wire and ground (see wiring diagram)

Please see electrical specifications by model and wiring diagram on the next page for additional electrical

information.

Each set of wires must be connected to its own individual double pole breaker.

Installation Instructions

STEP 1: Take each wire pair and connect them to one breaker (see wiring diagram). Make sure that each breaker

is connected with one black wire and one red wire

STEP 2: Using a suitable wire gauge that meets all applicable electrical codes for the size of the breakers used,

run the correct sets of wire from the home’s main breaker panel to the tankless water heater.

STEP 3: A separate ground conductor for each incoming circuit is required.

STEP 4: DOUBLE CHECK the electrical connections to make sure they are correct and that all wire connections

are tight and secure. Also confirm that the correct breaker size and wire gauge has been used and confirm that

the unit has been connected to a ground in accordance with applicable codes.

STEP 5: Confirm that all the air has been purged from the water lines prior to turning on power to the unit. Refer

to STEP 2 in the plumbing installation section.

CAUTION: Ensure that you have made the correct connections. You must follow the wire connection as shown

to ensure proper operation of the unit. If you mix up one set of wires with another, the unit will not operate

correctly even though it turns on and otherwise appears to function properly.

The water heater is now installed and ready to use! Follow the General Operating Instructions to complete the

setup. We highly recommend that this is done with the homeowner present.

Electrical Specifications by Model

MODELS

ECO 8

ECO11

ECO 18

ECO 24

ECO 27

ECO 36

ELEMENTS

VOLTAGE

240 V

MAX kW

8 kW

13 kW

18 kW

24 kW

27 kW

36 kW

kW PER ELEMENT

8 kW

6.5 kW

9 kW

8 kW

9 kW

9 KW

MAX AMPERAGE DRAW

33 AMPS

54 AMPS

75 AMPS

100 AMPS

112.5 AMPS

150 AMPS

REQUIRED BREAKERS

1 x 40 AMP

1 X 60 AMP

2 X 40 AMP

3 x 40 AMP

3 X 40 AMP

4 X 40 AMP

REQUIRED WIRE GAUGE

1 x 8 AWG

1 x 6 AWG

2 X 8 AWG

3 x 8 AWG

3 X 8 AWG

4 X 8 AWG

Wiring Diagram

Circuit Break #1 Circuit Breaker #2 Circuit Breaker #3 Circuit Breaker #4

208V Jumper Setting

When using 208V service for these units instead of 240V you must change the jumper setting to ensure proper

unit functionality. Using a 208V service will give you 75% capacity. There are two different types of control

boards: Thru Hole and Surface Mount. For assistance determining control board type, please visit

EcoSmartUS.com

Model

ECO 8

ECO 11

ECO 18

ECO 24

ECO 27

ECO 36

New Jumper Setting (Thru Hole)

5.5

New Jumper Setting (Surface Mount)

5.5

BLACK

RED

ECO 8 – ECO 11 requires 1

breaker and 1 set of wires

ECO 18 requires 2 sets of breakers and wires

ECO 24 – ECO 27 require 3 sets of breakers and wires

ECO 36 requires 4 sets of breakers and wires

BLACK

RED

BLACK

RED

BLACK

RED

6- SIZING GUIDE

Please use the chart below to see how many gallons per minute your tankless water heater can produce with

your incoming water temperature. The gallons per minute is calculated assuming 105°F outlet temperature.

Incoming Water

Temperature

ECO 8

ECO 11

ECO 18

ECO 24

ECO 27

ECO 36

40°F

0.8

1.4

1.9

2.5

2.8

3.8

45°F

0.9

1.5

2.0

2.7

3.1

4.1

50°F

1.0

1.6

2.2

3.0

3.4

4.5

55°F

1.1

1.8

2.5

3.3

3.7

4.9

60°F

1.2

2.0

2.7

3.6

4.1

5.5

65°F

1.4

2.2

3.1

4.1

4.6

6.1

70°F

1.6

2.5

3.5

4.7

5.3

7.0

75°F

1.8

3.0

4.1

5.5

6.1

8.2

80°F

2.2

3.6

4.9

6.6

7.4

9.8

(Gallons per Minute)

FLOW REGULATOR – OPTIONAL

To ensure the optimal temperature output and overall performance of your tankless water heater you may

require a flow regulator. These flow regulators are installed on the outlet connection of your tankless water

heater and limit the maximum volume coming out of your unit to a specified flow rate to prevent the exit

temperature from becoming too cool. To learn more about flow regulators or find out how to purchase one for

your tankless water heater visit us online at EcoSmartUS.com or contact us at 1-877-474-6473.

Steps for Choosing a Flow Regulator

1. Find your model in the chart on the left

2. Choose the column with the inlet water temperature closest to your geographical location

3. Take the GPM or gallons per minute you find and match it with the corresponding flow regulator on the

right

Inlet Water Temperature

40°F

50°F

60°F

70°F

EcoSmart Part

Number

Maximum Flow Rate

Connection Size

ECO 8

1.0

1.5

ECO IFR 1-2

1.0 GPM

1/2" Compression

ECO 11

1.0

1.5

2.0

1.5 GPM

1/2" Compression

ECO 18

2.0

3.0

2.0 GPM

1/2" Compression

ECO 24

2.0

3.0

4.0

ECO IFR 3-4

2.0 GPM

3/4" NPT

ECO 27

2.0

3.0

4.0

5.0

3.0 GPM

3/4" NPT

ECO 36

3.0

4.0

5.0

4.0 GPM

3/4" NPT

5.0 GPM

3/4" NPT

*Selection based on inlet temperature above and outlet temperature of 105°F

7- GENERAL OPERATING INSTRUCTIONS

Operating your new tankless water heater is similar to using any traditional water heating system. However, it is

very important that you carefully read all of the setup procedures and operating instructions and tips to ensure

the maximum performance and energy savings from your new water heater. We recommend that all members

of the household read these General Operating Instructions.

How your new water heater works: Your tankless water heater does not store hot water like a conventional

tank-type water heater. It contains high powered heating elements that are capable of heating water on-

demand. As soon as you turn on a hot water faucet, a sophisticated flow sensor recognizes that you have turned

on the water. This sensor measures flow rate while another sensor measures the incoming water temperature.

This information is transmitted continually to the computer logic controls which decide how much power to

send to the heating elements to heat the water to your desired temperature. Once the water faucet is turned off

your water heater will turn off as well.

8- MAINTENANCE

To ensure maximum performance of your water heater and to reduce the risk of a water leak, we recommend

the following maintenance:

Inspect the connections on the inlet and outlet of the water heater at least on an annual basis for any signs of

damage or failure. Any signs of damage, cracks, leakage or weakness should be addressed. Take care not to over

tighten the connections. Serious internal damage to your water heater can occur if you over tighten the water

heater connections at the unit.

IMPORTANT NOTES:

As with all electrical appliances, under no circumstances should you attempt to install, repair or disassemble this

water heater without first shutting off all power to the unit directly at the fuse or breaker box. SERIOUS BODILY

INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING.

When any maintenance is performed on the water heater or the home’s plumbing system that may introduce air

into the plumbing pipes, it is important to turn the power off to the water heater and purge the air out of the

lines before allowing the unit to power up. FAILURE TO DO SO COULD CAUSE PERMANENT DAMAGE TO THE

HEATING ELEMENT AND VOID YOUR WARRANTY.

If you have a water supply with a high level of mineralization (hard water), you should increase the frequency of

your maintenance.

9- TROUBLE SHOOTING GUIDE

Are you having problems with your water heater?

Please call or email our customer service and technical support team for any help you may need.

TOLL FREE 1-877-474-6473

[email protected]

The following table represents some of the most common technical support questions we receive. Before calling

us, please read thoroughly to see if your question or problem is addressed.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Water heater is not heating at all

(water is flowing but the unit is not

heating - the outgoing water

temperature is the same as the

cold water supply) - the digital

display does NOT light up.

No power or incorrect

wiring.

Make sure the breakers at main electrical panel are ON. You

may have a faulty breaker or unit may be wired incorrectly.

Flow rate is too low /

water pressure is too

low.

Your water heater has an activation flow rate of approximately

0.3 GPM. If your water flow rate is less than this level, your unit

will not activate. Increase the flow rate.

Water heater is not heating at all

(water is flowing but the unit is not

heating - the outgoing water

temperature is the same as the

cold water supply) The digital

display DOES light up.

Internal part failure.

Please call us for technical assistance.

Water heater is heating, but the

water temperature is not hot

enough.

User temperature

setting too low.

Turn up the temperature setting on the unit.

Flow rate is too high.

Depending on your incoming water temperature and the power

output of your model, your water flow rate may exceed the

physical heating capacity of your water heater. Reduce the flow

rate by installing an EcoSmart Flow Regulator. Use the chart in

section 6 to find out which flow regulator works best for your

particular model.

Crossed wires.

If it’s a new installation, have your electrician double check the

wiring. Is possible that the wiring is incorrect.

Voltage less than 240

volts.

The heating elements on your water heater are design for 240

volts. When used with a lower voltage, they produce less

heating power. You may need to upgrade to a larger model.

Mixing too much cold

water.

You do not need to mix as much cold water with your tankless

water heater compared to when you use a conventional water

heater. You may also have an anti-scald feature on your faucet

that is mixing cold water. These types of faucets can usually be

adjusted to reduce the amount of cold water mixed.

The water temperature at the

faucet is less than the temperature

setting of my water heater.

Voltage less than 240

volts.

The computer chips in your tankless water heater are

programmed with the expectation that your incoming line

voltage is 240 volts. If you have less than 240 volts, it may affect

the reading on your water heater’s digital display and cause it to

read slightly higher than the actual output temperature. To

compensate for this, increase the setting on your water heater if

you need / want hotter water.

Anti-Scald

pressure/balancing

valve or tempering

valve.

Your faucet may have an anti-scald feature or a tempering valve

that automatically mixes cold water even when you turn your

control lever or handle to full hot. These devices are usually

adjustable so you can turn off the cold mix completely. You can

compensate for this by increasing the setting on your water

heater if you need/want hotter water.

Thermal loss due to

long pipe run

As the hot water from the heater runs through the hot water

delivery system to your faucet, some heat will be lost especially

if it has long distance to travel or the pipes are cold. This is

normal. You can compensate for this by increasing the setting on

your water heater if you need/want hotter water.

10- USER INTERFACE

Power

 Click adjustment knob, the display will turn on

 Click the adjustment knob again, the display will turn off

C/F Conversion

 Press the adjustment knob for 3 seconds, the display will change from Fahrenheit to Celsius or vice

versa

Temperature Control

 Turning the knob clockwise increases the set output water temperature

 Turning the knob counter clockwise decreases the set output water temperature

 You can set or adjust the temperature at any time between 80°F – 140°F (27°C – 60°C). The temperature

can be changed to your desired setting. The display will only stay on when the unit is in use or when you

are setting the temperature.

CAUTION: Removing the cover to change the temperature set point exposes electrical shock and burn hazards,

which can cause INJURY or DEATH. Adjustment should only be done by a licensed plumber or electrician.

DANGER: Hotter water increases the potential for Hot Water SCALDS.

ECO 8 – ECO 11

ECO 18 – ECO 24 – ECO 27 – ECO 36

1. Hot Water Outlet

5. Adjustment Knob & Temperature Control

9. Electrical Strain Relief

2. Cold Water Inlet

6. Wire Connection

10. Mounting Bracket (1”)

3. Celsius/Fahrenheit Conversion (Press & Hold 3 sec.)

7. Brass Compression Nut

4. Temperature Set Point Display

8. Brass Compression Ferrule

Model Number

Height

Width

Depth

Pipe Centers Distance

ECO 8

𝟏

𝟐

⁄ inches

8 inches

𝟑

𝟒

⁄ inches

ECO 11

𝟏

𝟐

⁄ inches

8 inches

𝟑

𝟒

⁄ inches

ECO 18

17 inches

14 inches

𝟑

𝟒

⁄ inches

𝟕

𝟖

⁄ inches

ECO 24

17 inches

𝟑

𝟒

⁄ inches

𝟕

𝟖

⁄ inches

ECO 27

17 inches

𝟑

𝟒

⁄ inches

𝟕

𝟖

⁄ inches

ECO 36

17 inches

21 inches

𝟑

𝟒

⁄ inches

𝟏𝟑

𝟏𝟔

⁄ inches

ECOSMART GREEN ENERGY PRODUCTS

MANUFACTURERS WARRANTY

MAINLAND USA and CANADA- LIMITED LIFETIME

OUTSIDE MAINLAND USA – 5 YEARS

1. PRODUCT WARRANTY: EcoSmart Green Energy Products warrants to the original purchaser at the original address

or the authorized transferee of such purchaser (collectively, the “Buyer”) EcoSmart Tankless Water Heater and its

components to be free from defects in materials and workmanship, under normal use and service from the date of

installation, provided that the Product is installed within thirty (30) days from date of receipt and installed by a

licensed electrician and plumber (specific proof required) and maintained in accordance with Products written

instructions. The Product Warranty will be in effect upon receipt of the Warranty Registration by EcoSmart U.S.

offices. The Warranty Registration is included in the Operating and Maintenance Manual supplied with each new

product and must be fully completed and submitted via fax, mail or website within (30) days of receipt of Product.

Incomplete Warranty Registrations will not be accepted. Product Warranties are void without receipt of Warranty

Registration within (30) days of receipt of Product.

SUCH WARRANTIES DO NOT COVER:

 Product failure caused by liming, sediment buildup, chemical corrosion, chlorine/chloride corrosion, or

freezing.

 Product failure caused by the failure to remove air from system prior to or during operation.

 Product misuse, tampering or misapplication, accidental damage, improper installation or the application of

improper voltage.

 Costs incurred for shipping, delivery, handling and/or administrative charges.

 Labor charges of any kind.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.

2. LIMITATION OF REMEDIES AND DAMAGES: EcoSmart Green Energy Products liability and Buyer’s exclusive remedy

hereunder will be limited solely to repair or replacement of Product under Warranty by EcoSmart Service Center with

respect to any claim made within the applicable Warranty. EcoSmart Green Energy Products reserves the right to

accept or reject any such claim in whole or in part. EcoSmart Green Energy Products will not accept the return of any

product without prior written approval from EcoSmart Service Center and the issuance of a Return Merchandise

Authorization Number clearly marked on the outside packaging of the return shipment. ECOSMART GREEN ENERGY

PRODUCTS WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES,

INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF (OR INABILITY TO

USE) THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY

OTHER PRODUCT OR GOODS.

3. WARRANTY REGISTRATION: To be covered under the EcoSmart Green Energy Products Manufacturer’s Limited

Lifetime Warranty Buyer must register product within thirty (30) calendar days of receipt of Product using the

Warranty Registration Card included with the Product, this Warranty may be submitted via mail to ECOSMART GREEN

ENERGY PRODUCTS LOCATED AT 400 Captain Neville Drive, Waterbury, CT, 06705. THIS IS A LIMITED LIFETIME

MANUFACTURER’S WARRANTY THAT CONVEYS BENEFITS TO THE ORIGINAL PURCHASERS, SUBJECT TO THE TERMS

AND CONDITIONS SET FORTH HEREIN. Keep Product documents in a safe and secure location. Buyer obligation under

the terms of purchase and sale require that Warranty Registration must be returned within the prescribed timeframe

(within 30 calendar days) and retain all proof of purchase, installer receipts for Warranty in order to protect Buyer’s

rights and obtain Manufacturer’s Limited Lifetime Warranty benefits. The Warranty resides with the Buyer with proof

of purchase; not simply with an individual in possession of a Product. If the Product is to be installed in new

construction at a date later than 30 days from the date of receipt, send further information in advance of thirty (30)

day deadline when known so we may update your Warranty record.

4. FURTHER LIMITATIONS AND EXCLUSIONS AFFECTING YOUR WARRANTY: This warranty is void if the Product is not

installed in accordance with relevant, local electrical and plumbing codes and in accordance with the installation

instructions specified by the manufacturer. Local codes will override manufacturer’s instructions at the time of

installation and if additional installation parts are required, the costs will be the responsibility of Buyer. Above ground

level installations must be protected with drip pans and drains just as the codes call for protective requirements used

in regular hot water tank installations. Buyer hereby accepts the entire responsibility for ascertaining whether they

have sufficient electrical power at their residence to operate our Electric Tankless Water Heaters as indicated in our

specifications which are readily available at our website (WWW.ECOSMARTUS.COM), in our brochures and contained

in the shipping box for installers to read before installations. If, within (30) days of purchase and prior to installation,

the Buyer finds that the purchased unit is not suitable for their demands Buyer must return the unit to the EcoSmart

office. Buyer is responsible for any charges that may be incurred to complete the return. A Buyer is eligible for a full

refund or credit ONLY if the returned unit is received by EcoSmart within thirty (30) calendar days of receipt AND has

been inspected by EcoSmart and found to be in the same condition as when purchased. Only when these two

conditions are met will a Buyer receive a refund or replacement unit. EcoSmart Green Energy Products will not accept

the return of any product without prior written approval from EcoSmart Green Energy Products and the issuance of a

Return Merchandise Authorization Number clearly marked on the outside packaging of the return shipment.

AFTER (30) CALENDAR DAYS FROM RECEIPT OF PRODUCT THERE WILL BE NO RETURNS OR WARRANTY WITHOUT

RECEIPT OF WARRANTY REGISTRATION BY ECOSMART US. BUYER ACCEPTS ALL SALES AS FINAL. ANY ALTERATION TO

THE PRODUCT VOIDS ALL WARRANTIES. ECOSMART GREEN ENERGY PRODUCTS IS NOT RESPONSIBLE FOR ANY OTHER

CHARGE OR EXPENSE INCURRED, OTHER THAN THE ORIGINAL PURCHASE PRICE OF THE PRODUCT. ECOSMART GREEN

ENERGY PRODUCTS shall not be liable for consequential, special, incidental or contingent expenses or damages arising

directly or indirectly from any defect in or of the Product; nor will EcoSmart Green Energy Products be liable for any

water damage arising directly or indirectly from the use of the Product or from the failure of or defect in any

component part or connecting plumbing. EcoSmart Green Energy Products and Buyer agree to the above terms in

their entirety and accept all sales as final without recourse to a credit card company or other financial institution and

hereby agree to stipulations and specifications defined within Manufacturer’s Limited Lifetime Warranty.

5. Warranty Procedure for service: Have a licensed electrician determine the exact issue that requires repair. Please

note that technical support is available for qualified technicians only (licensed electricians and/or plumbers). Technical

support that involves potentially dangerous electrical conditions is not available to unqualified persons. When

contacting EcoSmart Service Center, please be sure that the technician has a copy of the original Warranty

Registration and has reviewed the “Homeowners and Installation Manual” that was supplied with the Product.

EcoSmart Technical Assistance, at its sole discretion, will determine the best method for repair. Methods of repair

include, but are not limited to, replacement of specific part of Product or replacement of whole unit. If a whole unit

requires replacement under the terms of this Manufacturer’s Warranty, the original unit must be returned to the

ECOSMART office. Buyer must secure the cost of return delivery and replacement unit with a valid U.S. credit card.

Credit Card Authorization Forms are available upon request. If the replaced unit arrives at the EcoSmart office within

ten (10) calendar days of shipment of new unit and is found to comply within the specifications of this Manufacturer’s

Warranty then the credit card will not be charged, otherwise, Buyer will be charged amount of replacement unit and

shipment cost as agreed upon within Credit Card Authorization Form. If EcoSmart Technical Assistance determines a

component requires repair or replacement under the terms of this Manufacturer’s Limited Lifetime Warranty, the part

will be shipped via standard ground delivery. If faster shipping service is desired, the Buyer must select and pay for

same.

ANY QUESTIONS REGARDING OUR FIVE (5) YEAR WARRANTY SHOULD BE DIRECTED TO OUR SERVICE CENTER BY

CALLING TOLL FREE 877-474-6473 BETWEEN 8:00 AM and 5:00 PM MONDAY thru FRIDAY EASTERN TIME. NO RETURN

WILL BE ACCEPTED BY ECOSMART WITHOUT PRIOR APPROVAL AND THE ISSUANCE OF RETURN MERCHANDISE

AUTHORIZATION NUMBER CLEARLY MARKED ON THE EXTERIOR OF PACKAGING.

EcoSmart Green Energy Products • 400 Captain Neville Drive, Waterbury, CT, 06705 • TOLL FREE: 877-474-6473

ECOSMART SPANISH MANUAL

INSTRUCCIONES DE INSTALACIÓN Y MANUAL DEL PROPIETARIO

ECO 8 | ECO 11 | ECO 18 | ECO 24 | ECO 27 | ECO 36

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

Cuando se instala o usa un aparato eléctrico de alto voltaje, siempre se deben tener en cuenta precauciones de

seguridad básicas. En ningún caso se debe intentar limpiar, instalar, inspeccionar, reparar, desarmar ni reparar de

ninguna otra manera este calefón calentador de agua sin apagar primero toda la alimentación de energía a la unidad

directamente en la caja de disyuntores. SI SE IGNORA ESTA ADVERTENCIA SE PUEDEN PRODUCIR LESIONES

CORPORALES GRAVES O LA MUERTE.

ESTE PRODUCTO DEBE SER INSTALADO POR UN ELECTRICISTA CALIFICADO Y UN PLOMERO CALIFICADO DE

ACUERDO CON TODOS LOS CÓDIGOS ELÉCTRICOS Y DE PLOMERÍA NACIONALES, ESTATALES, PROVINCIALES Y

LOCALES.

POR FAVOR, LEA ESTAS INSTRUCCIONES METICULOSAMENTE Y EN SU TOTALIDAD ANTES DE LA INSTALACIÓN Y EL

USO. DE NO HACERLO SE PODRÍAN PRODUCIR DAÑOS MATERIALES, LESIONES GRAVES O LA MUERTE.

Este manual se debe entregar al propietario después de la instalación y se debe conservar para referencia futura.

Probado y certificado por la Water Quality Association de conformidad con la norma NSF/ANSI

372 sobre cumplimiento de ausencia de plomo.

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

LEA TODAS LAS INSTRUCCIONES ANTES DEL USO

¡PELIGRO!

GRADUACIÓN SEGURA DE LA TEMPERATURA DEL AGUA

La seguridad y la conservación de la energía son factores a considerar cuando se

selecciona la graduación de temperatura del agua del termostato del calefón

calentador de agua. La temperatura del agua por encima de 125°F puede causar

quemaduras graves o la muerte por escaldaduras. Asegúrese de leer y observar las

advertencias indicadas en la etiqueta que se ve en la imagen de abajo. Esta etiqueta

también se encuentra en el calefón calentador de agua cerca del panel de acceso al

termostato.

Aviso: Se recomiendan las válvulas mezcladoras para

reducir la temperatura del agua en el punto de uso

mezclando agua caliente y fría en las tuberías de derivación.

Se recomienda instalar una válvula mezcladora que cumpla

con la Norma para Válvulas Mezcladoras Activadas por

Temperatura para Sistemas de Distribución de Agua Caliente

ASSE 1017.

El cuadro que aparece arriba se puede usar como guía para

determinar la temperatura del agua adecuada para su hogar.

PELIGRO: Los hogares donde hay niños pequeños,

discapacitados o ancianos pueden necesitar una graduación

del termostato de 120° F o menos para evitar el contacto con

agua "CALIENTE". La temperatura del agua del calefón se

regula mediante el control electrónico que está en el frente

del mismo. Para cumplir con las regulaciones de seguridad, el

termostato se graduó en 120°F antes del embarque del

calefón en fábrica.

Por favor, consulte la Sección

10 para más información

acerca de la graduación de

temperatura de su calefón.

Rote hacia la derecha para

mayor temperatura (hasta

140°F) o hacia la izquierda

para menos temperatura

(hasta 80°F); aparecerá en la

pantalla encima de la perilla.

ACERCA DE SU CALEFÓN SIN TANQUE

¡Felicitaciones por la compra del calefón eléctrico sin tanque! Usted ha comprado el calefón eléctrico sin tanque

tecnológicamente más avanzado del mercado actual.

Su nuevo calefón eléctrico sin tanque presenta sensores avanzados de temperatura y velocidad de caudal diseñados

para modular energía a los elementos calefactores para mantener la temperatura exacta del agua de salida

seleccionada por el usuario entre 80°F y 140°F (sujeto a la temperatura del agua de entrada y el suministro de energía

del modelo seleccionado).

Para obtener el mejor rendimiento y ahorro energético de su calefón eléctrico sin tanque es importante que se lo

instale de acuerdo con nuestras instrucciones y los códigos eléctricos y de plomería aplicables a su área y que lea este

manual meticulosamente para compenetrarse de las instrucciones operativas y sugerencias importantes.

Si tiene alguna pregunta en cualquier momento, por favor, comuníquese con nosotros directamente en:

EcoSmart Green Energy Products

400 Captain Neville Drive, Waterbury, CT 06705

Teléfono para llamadas gratuitas: 1-877-474-6473

Support@EcoSmartUS.com

CONTENIDO

1. ANTES DE LA INSTALACIÓN

2. SELECCIÓN DEL LUGAR DE INSTALACIÓN

3. MONTAJE DE SU CALEFÓN

4. INSTALACIÓN DE PLOMERÍA

5. INSTALACIÓN ELÉCTRICA

6. GUÍA DE TAMAÑOS

7. INSTRUCCIONES OPERATIVAS GENERALES

8. MANTENIMIENTO

9. GUÍA PARA LA SOLUCIÓN DE PROBLEMAS

10. INTERFAZ DEL USUARIO

1 – ANTES DE LA INSTALACIÓN

POR FAVOR, LEA ESTAS INSTRUCCIONES METICULOSAMENTE Y EN SU TOTALIDAD ANTES DE LA INSTALACIÓN Y EL

USO. SI NO SE RESPETAN LAS INSTRUCCIONES SE PODRÍAN PRODUCIR DAÑOS MATERIALES, LESIONES PERSONALES

GRAVES O LA MUERTE.

Al instalar este producto usted reconoce los términos de la garantía del fabricante. Después de instalado el calefón no

devuelva el producto al lugar de compra. Si tiene alguna pregunta sobre la garantía o las políticas de devolución del

producto, por favor, comuníquese con EcoSmart al 1-877-474-6473.

Inspeccione todos los componentes. El contenido de la caja debe incluir una de las siguientes unidades:

 ECO 8

 ECO 11

 ECO 18

 ECO 24

 ECO 27

 ECO 36

2 - SELECCIÓN DEL LUGAR DE INSTALACIÓN

Este producto únicamente se puede instalar en interiores. Puede instalar su unidad en una ubicación exterior en tanto

y en cuanto se lo coloque en un cerramiento adecuado que lo proteja de la lluvia, salpicaduras de agua, la luz solar

directa, residuos e insectos.

NO instale este producto en un lugar donde pueda estar sujeto a temperaturas de congelación. Si el agua que está

dentro de su calefón sin tanque se congela puede causar daños graves y permanentes que no son cubiertos por la

garantía.

NO coloque el calefón en un lugar de difícil acceso.

Asegúrese de que el calefón y el caño de salida del agua caliente no estén al alcance de los niños, de manera que no

estén en condiciones de alterar los controles de temperatura ni de lesionarse al tocar la cañería de salida del agua

caliente. La cañería del agua de salida puede estar muy caliente.

Este producto NO necesita ventilación.

Evite instalar su calefón sin tanque en un lugar propenso a la humedad excesiva o el polvo o en un área donde pueda

ser salpicado con agua u otros líquidos. NO lo instale debajo de cañerías de agua o aire acondicionado que puedan

tener pérdidas o condensar humedad que pudieran luego gotear dentro del calefón. NO lo instale encima de tableros

o cajas de empalme eléctricos.

PRECAUCIÓN: El calefón no se debe ubicar en un área donde un derrame provoque daños al área adyacente o los

pisos inferiores de la estructura. Si no se pueden evitar esas áreas, se recomienda instalar una bandeja de goteo

adecuada, con buen drenaje, debajo del calefón.

3 - MONTAJE DE SU CALEFÓN

Su calefón sin tanque se debe sujetar a la superficie de montaje con 4 tornillos (1 pulgada de largo como mínimo)

usando las ménsulas de montaje incorporadas a cada lado del calefactor. Asegúrese de que la superficie de montaje

sea sólida y firme y que la unidad quede nivelada antes de sujetar los tornillos. Para facilitar la instalación y el

mantenimiento, recomendamos que este producto se instale en posición vertical, con las conexiones de agua de

entrada y salida en la parte inferior de la unidad en el caso de las ECO 18, ECO 24, ECO 27 y ECO 36 y con las

conexiones de agua de entrada y salida en los lados izquierdo y derecho en el caso de las unidades ECO 8 y ECO 11.

Separaciones recomendadas: 12 pulgadas encima y debajo del calefón

6 pulgadas delante y a los costados del calefón

PRECAUCIÓN: Los materiales combustibles se deben mantener a 24 pulgadas de distancia de su calefón y del caño

de salida de agua caliente.

4 – INSTALACIÓN DE PLOMERÍA

Por favor, siga todas las instrucciones de plomería con atención. Recomendamos que este producto sea instalado por

un plomero matriculado y calificado de conformidad con todos los códigos de plomería nacionales, estatales,

provinciales y locales aplicables.

Instrucciones de instalación

PASO 1: Conecte la cañería de AGUA CALIENTE con la SALIDA del calefón ubicada del lado izquierdo mirando la unidad

de frente. Conecte la cañería de AGUA FRÍA con la ENTRADA marcada del calefón ubicada del lado derecho mirando la

unidad de frente.

PASO 2: Después de apretar las dos uniones del calefón, abra varios grifos de agua caliente y deje correr el agua a

través del calefón durante al menos 2 ó 3 minutos. Este proceso purga todo el aire de las cañerías y SE DEBE realizar

antes de encender la alimentación eléctrica de la unidad. SI NO SE REALIZA ESTE PASO SE PUEDEN PRODUCIR DAÑOS

PERMANENTES EN LOS ELEMENTOS CALEFACTORES. Si se realiza alguna tarea de mantenimiento del calefón o del

sistema de cañerías del hogar que pudiera introducir aire en las cañerías es importante apagar el suministro eléctrico

del calefón y purgar el aire de las cañerías antes de encender la unidad.

PASO 3: Inspeccione con atención todas las conexiones, uniones y la válvula de alivio de presión (en caso de haber)

para detectar cualquier pérdida.

AVISOS IMPORTANTES:

1. No suelde ningún caño con la unidad conectada a la cañería; el calor de soldadura puede dañar el sensor de

caudal. Si lo hace se anulará la garantía.

2. Este calefón automático sin tanque está equipado con interruptores de termostato de restauración

automática electromecánicos y controlados por computadora para protección contra alta temperatura por

limitación. Como este producto no usa un tanque de almacenamiento en la mayoría de las instalaciones no

se necesita una válvula de alivio de presión y temperatura (T&P). La norma UL 499 NO exige el uso de una

válvula de alivio de presión. Sin embargo, tal vez sea necesario instalar una válvula T&P para cumplir con los

códigos de su área. Si es así, instale la válvula de alivio de presión de acuerdo con los códigos locales y

asegúrese de que funcione correctamente y que el aire se purgue de la válvula antes de instalar el calefón. Al

conectar con un tubo CPVC flexible o de alta temperatura recomendamos usar una válvula T&P para mayor

seguridad.

Por favor, tenga en cuenta lo siguiente: Las instalaciones realizadas en el Estado de Massachusetts y en el

Estado de Kentucky exigen válvula de alivio de presión. Por favor, consulte los códigos de instalación

locales para ver los requisitos especiales.

3. La presión de agua operativa máxima es 150 psi. Si la presión de agua es superior, se debe instalar una

válvula reductora de presión en la tubería de suministro de agua de entrada principal antes de instalar el

calefón eléctrico sin tanque.

4. Se recomienda el uso de mangueras flexibles para calefón como parte de la instalación. Al conectar el caño

de agua de entrada a la unidad asegúrese de usar una llave para sujetar la conexión de la unidad y otra llave

para ajustar, de manera que el sensor de caudal de la unidad no se suelte ni dañe. Se pueden producir daños

internos graves en el calefón si las conexiones de entrada o salida se aprietan en exceso o si se realizan

conexiones de soldadura.

5. Recomendamos instalar una válvula de cierre manual (válvula esférica) en la entrada y salida del calefón de

manera que haya un punto de cierre conveniente disponible en caso de ser necesario realizar alguna tarea de

mantenimiento o reparación en el futuro. Es sumamente importante lavar las cañerías con chorro de agua

para eliminar cualquier pasta o residuo de plomería de las mismas que pudiera ser causado por soldadura

antes de conectar los caños al calefón.

Recomendamos que todas las cañerías o mangueras de agua que se encuentren dentro de 3 pies de distancia de las

conexiones de entrada y salida tengan capacidad nominal para aplicaciones de alta temperatura con un valor mínimo

de 150°F.

5 – INSTALACIÓN ELÉCTRICA

EcoSmart recomienda que este producto sea instalado por un electricista matriculado y calificado de conformidad con

todos los códigos de electricidad nacionales, estatales, provinciales y locales aplicables. Como sucede con todos los

aparatos eléctricos, en ningún caso debe intentar instalar, reparar ni desarmar este calefón sin antes desconectar

todo el suministro eléctrico de la unidad directamente en la caja de fusibles o disyuntor. Asegúrese de desconectar

todos los disyuntores. SI SE IGNORA ESTA ADVERTENCIA SE PUEDEN PRODUCIR LESIONES CORPORALES GRAVES O

LA MUERTE.

Todo el cableado (calibre del cable) y la protección de circuitos (disyuntores) deben cumplir con el Código Eléctrico

Nacional en EE.UU. (NEC) o el Código Eléctrico Canadiense de Canadá (CEC). De lo contrario se pueden producir daños

materiales y/o lesiones personales y se anula la garantía. Nota: El Código Eléctrico Canadiense generalmente exige

que todos los cables de suministro y la protección de circuitos correspondiente utilizados para la calefacción

doméstica por agua caliente y las aplicaciones de calefacción hidrónica sean de una medida como mínimo igual al

125% de la capacidad nominal máxima del calefón (vea los detalles en las especificaciones del modelo más abajo).

Antes de instalar este producto, asegúrese de que el hogar tenga suficiente energía eléctrica disponible para manejar

la carga de amperaje máxima del modelo aplicable.

AVISOS IMPORTANTES:

Los modelos ECO 8 y ECO 11 exigen 1 juego de cable y tierra (vea el diagrama de cableado)

El modelo ECO 18 exige 2 juegos de cable y tierra (vea el diagrama de cableado)

Los modelos ECO 24 y ECO 27 exigen 3 juegos de cable y tierra (vea el diagrama de cableado)

El modelo ECO 36 exige 4 juegos de cable y tierra (vea el diagrama de cableado)

Por favor, vea las especificaciones eléctricas por modelo y diagrama de cableado en la página siguiente para

consultar información eléctrica adicional.

Cada juego de cables se debe conectar con su propio disyuntor de doble polo individual.

Instrucciones de instalación

PASO 1: Tome cada par de cables y conéctelo con un disyuntor (vea el diagrama de cableado). Asegúrese de que cada

disyuntor se conecte con un cable negro y un cable rojo

PASO 2: Con un calibre de cable adecuado que cumpla con todos los códigos eléctricos aplicables para el tamaño de

disyuntores utilizados, tienda los juegos correctos de cable desde el tablero del disyuntor principal de su hogar hasta

el calefón sin tanque.

PASO 3: Se necesita un conductor de tierra separado para cada circuito de entrada.

PASO 4: VUELVA A COMPROBAR las conexiones eléctricas para asegurarse de que sean correctas y que todas las

conexiones de cables estén firmes y sujetas. También confirme que se haya utilizado el tamaño de disyuntor y el

calibre de cable correctos y que la unidad se haya conectado a tierra de acuerdo con los códigos aplicables.

PASO 5: Confirme que se haya purgado todo el aire de las cañerías de agua antes de encender el suministro eléctrico

de la unidad. Consulte el PASO 2 de la sección instalación de plomería.

PRECAUCIÓN: Asegúrese de haber hecho las conexiones correctas. Debe seguir la conexión de cables tal como se

muestra para asegurar el funcionamiento adecuado de la unidad. Si mezcla un juego de cables con otro la unidad no

funcionará correctamente aun cuando se encienda y parezca funcionar correctamente. ¡El calefón ya está instalado y

listo para el uso! Siga las Instrucciones Operativas Generales para completar la instalación. Recomendamos

enfáticamente que esto se realice en presencia del propietario.

Especificaciones eléctricas por modelo

MODELOS

ECO 8

ECO11

ECO 18

ECO 24

ECO 27

ECO 36

ELEMENTOS

VOLTAJE

240 V

MÁX kW

8 kW

13 kW

18 kW

24 kW

27 kW

36 kW

kW POR ELEMENTO

8 kW

6,5 kW

9 kW

8 kW

9 kW

9 KW

AMPERAJE MÁXIMO

33 AMP

54 AMP

75 AMP

100 AMP

112,5 AMP

150 AMP

DISYUNTORES

REQUERIDOS

1 x 40

AMP

1 x 60

AMP

2 x 40

AMP

3 x 40

AMP

3 x 40

AMP

4 x 40

AMP

CALIBRE DE CABLE

REQUERIDO

1 x 8 AWG

1 x 6 AWG

2 x 8 AWG

3 x 8 AWG

4 x 8 AWG

Diagrama de cableado

Disyuntor #1 Disyuntor #2 Disyuntor #3 Disyuntor #4

Configuración De Puente 208V

Cuando utilice un servicio de 208V para estas unidades de 240V debe cambiar la configuración del puente para

asegurarse de que la unidad funcione correctamente. Si utiliza un servicio de 208V tendrá un 75% de capacidad.

Hay dos tipos diferentes de tableros de control: Agujero pasante y montaje en superficie. Para obtener asistencia

respecto del tipo de tablero de control, visite EcoSmartUS.com

Model

ECO 8

ECO 11

ECO 18

ECO 24

ECO 27

ECO 36

Nueva configuración de puente (Agujero pasante)

5.5

Nueva configuración de puente (Montaje en superficie)

5.5

ECO 8 – ECO 11 exigen 1

disyuntor y 1 juego de cables

ECO 18 exige 2 juegos de disyuntores y cables

ECO 24 – ECO 27 exigen 3 juegos de disyuntores y cables

ECO 36 exige 4 juegos de disyuntores y cables

NEGRO

ROJO

NEGRO

ROJO

NEGRO

ROJO

NEGRO

ROJO

La page charge ...

EcoSmart CB QC MEDLRG Manuel utilisateur

Marque: EcoSmart

Modèle: CB QC MEDLRG

Catégorie: Chauffe-eau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: EcoSmart CB QC MEDLRG User manual
español: EcoSmart CB QC MEDLRG Manual de usuario

EcoSmart CB QC MEDLRG Manuel utilisateur

EcoSmart CB QC MEDLRG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents