brondell LH-20 Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

OWNER'S MANUAL
LH-22 Bidet Attachment
Dual-Temperature / Dual-Nozzles
Attach Proof of Purchase to This Page
Adjunte prueba de compra a esta página
Joindre une preuve d’achat à cette page
1
CONTENTS
PRODUCT INFORMATION
Product Features .................... Page 2
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Product Dimensions .................. Page 4
PRODUCT INSTALLATION
Before Installation ................... Page 5
Connecting the Cold Water Supply ..... Page 6
Connecting the Hot Water Supply ...... Page 8
Installing the Bidet Attachment ........ Page 10
PRODUCT OPERATION
Using the SouthSpa .................. Page 12
Nozzle Positioning ................... Page 12
MAINTENANCE
Cleaning the SouthSpa ............... Page 13
Short Term Non-Use ................. Page 13
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . Page 14
CONTACT .......................... Page 15
SPANISH VERSION .................. Page 16
FRENCH VERSION .................. Page 31
2
PRODUCT INFORMATION
High-quality ABS material with full body panel
Hygienic dual retractable nozzles
Self-cleaning nozzle feature
Adjustable temperature for ambient and warm water washes
Positionable nozzles
Adjustable water pressure
Ceramic core internal valve with patented uni-body construction
for safety
High-quality metal 7/8” and 3/8" T-valves
Durable braided metal cold water hose
High-temperature, durable hot water flex tubing
No electricity or batteries required
Easy installation and adjustable toilet fit
All accessories included for standard installation
One-year warranty
PRODUCT FEATURES
3
Bidet attachment with turn-dial control and adjustable brackets
PARTS LIST
25” braided metal
bidet hose
Cold water 7/8"
T-valve Connector
Hot water T-alve with
1/4" Pressure Connector
& Pressure Cap
(3/8" x 3/8")
Large rubber washer (2)
Small rubber washer (2)
Hot water supply cap
1/4" Hot water flex tubing
Hot water flex tubing
pressure connector
with pressure cap
4
PRODUCT DIMENSIONS
PRODUCT INFORMATION (cont.)
1.6" at deepest point
on control panel
0.4" at deepest
point on body
6.5"
10.6"
3.7"
2.7" 5.5"
17.3"
8.7"
3.5"
5
Check the size of the hot water supply connection (most likely under the sink/wash
basin). This needs to be a 3/8” connection for our T-valve to install.
Note: if the connection is a 1/2” connection, you will need to purchase the following
reducing adapter available online and at many plumbing hardware stores: Reducing
Adapter, 1/2” Female NPT x 3/8” Male Compression.
IMPORTANT
Please be advised that the provided
T-Valve should be installed at the Fill
Valve under the toilet tank, and NOT
at the cold water supply coming from
the wall.
If you do not have access to the Fill
Valve under the toilet tank, contact
Brondell Customer Service at
888.542.3355. We may be able to
guide you through the process.
PRODUCT INSTALLATION
BEFORE INSTALLATION
Check Water Supply Line
Check the water supply line that connects the toilet tank fill valve to the water
shuto valve at the wall. If it is a rigid pipe, you will need to purchase a flexible
water supply hose to replace it before installing the SouthSpa. The length of the
hose may vary, and the top connection size should be 7/8” Ballcock to connect to
the T-valve that you will install under the toilet tank, and the bottom connection will
vary (most common are 3/8” and 1/2” female compression).
6
PRODUCT INSTALLATION cont.)
CONNECTING THE COLD WATER SUPPLY
3. Connect 7/8” T-Valve to Water Supply Line and
Fill Valve Under Toilet Tank.
a. Install the 7/8” T-valve with one or both of
the rubber washers to the incoming water
connection on the bottom of your toilet tank.
b. Connect the cold water supply line coming
from the wall to the bottom of the T-valve.
Step 3a
Step 3b
1. Remove existing toilet seat
a. Lift hinge covers and use flathead or Phillips
head screwdriver to remove the mounting
bolts. Alternatively, you may need to loosen
mounting bolts underneath the seat.
b. Remove the toilet seat and set the seat,
mounting bolts and hardware aside.
Step 1b
Step 2c
2. Turn o water supply valve and flush toilet
a. Turn o water supply at the wall to stop flow of
water.
b. Flush toilet and hold down handle to
completely empty toilet tank.
c. Disconnect water supply hose from the fill
valve under the toilet tank.
7
IMPORTANT
If you are only connecting the cold water supply,
you must install the Hot Water Supply Cap
(provided - see Page 3) over the hot water
connection on your SouthSpa (see diagram).
Failure to connect or cap the hot water supply will
result in leaking during use.
After installing hot water cap, proceed to "Installing
the Bidet Attachment" on Page 10.
If you wish to also connect your hot water supply,
then proceed to "Connecting the Hot Water Supply"
on Page 8.
CONNECTING THE COLD WATER SUPPLY (cont.)
4. Connect Bidet Hose to T-Valve
a. Connect one end of the braided metal bidet
hose to the remaining open side of the
installed T-valve.
Step 4a
8
1. Connect the hot water supply
a. Locate the hot water supply line in your
bathroom under your sink/washbasin and turn
the water supply valve all the way o.
b. Drain the hot water line by turning on the sink
tap on the hot setting until no more water
comes out.
c. Disconnect hot water supply hose to sink from
shut o valve. You may have to use a 3/8”
compatible wrench or a similar tool
(not supplied).
Note: there may be some residual water in the
hose, use a small container or towel to catch
any residual water.
2. Install the Hot Water 3/8" T-valve and the small
rubber washers as needed onto the hot water
shut o valve under the sink.
3. Reconnect hot water supply line to open end
(top) of T-valve.
Step 1c
Steps 2 and 3
CONNECTING THE HOT WATER SUPPLY
PRODUCT INSTALLATION cont.)
9
Step 4c
Step 4b
CONNECTING THE HOT WATER SUPPLY (cont.)
4. If it hasn't been removed already, unscrew the
Pressure Cap covering the Pressure Connector.
a. Slide the Pressure Cap over the open end of
the of Hot Water Flex Tubing with the inside
threads facing towards the open end.
b. Push the Hot Water Flex Tubing over the
Pressure Connector.
IMPORTANT: Be sure to slide the Hot Water
Flex Tubing over the Pressure Connector until
the tubing slides past the “lip” of the pressure
connector and it cannot go any further.
c. Slide the Pressure Cap down until the cap
meets the Pressure Connector. Screw the Cap
onto the T-Valve until secure and tight.
Caution: Do not over-tighten the Pressure Cap.
You will risk damaging the tubing.
Step 4a
10
INSTALLING THE BIDET ATTACHMENT
2. Connect Cold Water Bidet Hose to Bidet
Attachment
a. Connect the open end of bidet hose to the
Cold connection on the back of the bidet
attachment.
Note: If you have already installed the Hot
Water Supply Cap over the hot water supply
on your SouthSpa, Skip to Step 4 on Page 11.
Otherwise continue with the installation at the
top of Page 11.
1. Install Bidet Attachment on Toilet
a. Place bidet attachment on the toilet so the
nozzles are as close to the back of the toilet
bowl as they will go. This will vary by toilet.
b. Make sure the adjustable brackets line up with
the holes in the toilet fixture. You may need to
rotate the adjustable brackets to line up with
the bolt holes properly.
c. Replace the toilet seat on top of bidet
attachment and secure using original toilet
seat hardware. Make sure to tighten so that the
bidet attachment and seat do not move.
Step 1a
Step 1b
Step 2a
PRODUCT INSTALLATION cont.)
11
INSTALLING THE BIDET ATTACHMENT (cont.)
3. Connect Hot Water Supply to Bidet Attachment
a. Slide the Pressure Cap over the open end of
the of Hot Water Flex Tubing with the inside
threads facing towards the open end.
b. Push the Pressure Connector into the open
end of the of Hot Water Flex Tubing with the
washer facing out.
IMPORTANT: Be sure to slide the Hot Water
Flex Tubing over the Pressure Connector until
the tubing slides past the “lip” of the pressure
connector and it cannot go any further.
c. Hold the Pressure Connector up against the
hot water inlet on the bidet attachment. Slide
the Pressure Cap along the tubing and screw
the Cap onto the hot water inlet until the
Pressure Connector is secure.
Step 3c
4. Turn on Water Supply & Check for Leaks
a. Open the hot and cold water supply valves
slowly and check for leaks.
b. Wait 5-10 minutes, check again and if there are
no leaks continue.
Note: If there is any leaking, check all rubber
washers and make sure all water connections
are tight and secure. If necessary, you can use
plumbers tape for any leaking connections.
Step 3a
Step 3b
12
If only connected to cold water, make sure that the
temperature dial on the bidet attachment is turned
as far as it can go towards “COLD” setting for best
pressure adjustability.
To adjust water temperature (when both hot and cold
water are connected), turn temperature dial slowly
towards “HOT” until the desired temperature is
reached.
Note: There may be a delay in the warm water
reaching the bidet attachment as the cold water
in your pipes clears and is replaced with hot water
(similar to the delay when you turn your faucet on).
Tip: For a quick and easy way to get warm water to
the bidet, run the “Nozzle Cleaning” function with the
warm water turned on for a short time until the water
heats up, then use as normal.
For the general bidet wash function, turn the dial towards either the Front (also
known as the Feminine) wash position, or the Rear (also known as the Posterior)
wash position.
The further the dial is turned, the higher the water pressure will be.
To lower the water pressure, turn the dial back towards the center.
To clean the bidet nozzle, turn the control dial towards the “Nozzle Cleaning”
position and water will wash over the nozzles.
USING THE SOUTHSPA
The nozzles can be easily adjusted by gently pulling the end of the nozzle forward
or backwards. Once desired position is set, the nozzle will remain in that position
until manually moved.
WARNING: Risk of scalding. High water temperature can cause severe burns.
Be sure to set the water temperature for your hot water heater at or below
120°F (49°C) and use extreme caution when mixing hot and cold water during
use. Brondell is not liable for any misuse of product or failure to use caution
when connecting to hot water.
NOZZLE POSITIONING
PRODUCT OPERATION
13
To clean the nozzles, gently pull down on the head of the nozzle, and use a
toothbrush or soft cloth and mild detergent (such as dish soap). You may also
unscrew the nozzle tip cap for a more thorough cleaning or use a toothpick if any
nozzle holes are plugged with hard water buildup. When cleaning, be careful not to
drop or flush the nozzle cap.
To clean the bidet, use a mild cleaner such as Simple Green or Windex spray to
clean the SouthSpa. Do not scrub or use harsh, abrasive products to clean the
SouthSpa, which may scratch the product.
MAINTENANCE
SHORT TERM NON-USE
CLEANING THE SOUTHSPA
If the product will not be used for more than a few weeks, you may consider shutting
the water supply o at the wall for extra precaution.
14
WARRANTY
Brondell products are backed by some of the most comprehensive warranties in the industry.
Brondell warrants that all products (excluding consumable items) shall be free from defects in material
and workmanship under normal use and service.
SouthSpa LH-10, LH-12, LH-20, LH-22 Residential One-Year Limited Warranty
100% Coverage of all parts and labor for the entire product for the first year from original date of
purchase.
SouthSpa LH-10, LH-12, LH-20, LH-22 Commercial Warranty
Warranty period 1 year from original purchase date for all Brondell products. Warranties may not
apply to products that are used for heavy commercial, hospital, or other high use non-residential
applications.
Exclusions and Limitations
1. BRONDELL warrants its products to be free from manufacturing defects under normal use and
service. This warranty is extended only to the ORIGINAL PURCHASER.
2. BRONDELL’s obligations under this warranty are limited to repairs or replacement, at BRONDELL’s
option, of products or parts found to be defective, provided that such products were properly
installed and used in accordance with instructions. BRONDELL reserves the right to make such
inspections as may be necessary in order to determine the cause of the defect. BRONDELL will not
charge for labor or parts in connection with warranty repairs for the first three years from date of
purchase on all products except those that may be subject to commercial use limitations.
3. BRONDELL is not responsible for the cost of removal, return (shipping) and/or re-installation of
products. This warranty does NOT apply to:
Damage or loss which occurs during shipment.
Damage or loss sustained through any natural or man-made causes beyond the control of
BRONDELL, including but not limited to fire, earthquake, floods, etc.
Damage or loss resulting from sediments or foreign matter contained in a water system.
Damage or loss resulting from negligent or improper installation including installation of a unit
in a harsh or hazardous environment.
Damage or loss resulting from removal, improper repair, modification of the product, or
improper maintenance including damage caused by chlorine or chlorine related products
Damage or loss resulting from electrical surges, electrical outages, lightning strikes, or other
acts which are not the fault of Brondell or which the Product is not specified to tolerate.
4. This warranty gives you specific legal rights. You may have other rights which vary from state to
state.
THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY
AVAILABLE TO THE PURCHASER. BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE
OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL, FOR CONSEQUENTIAL DAMAGES
OR EXPENSES INCURRED BY THE PURCHASER OR FOR LABOR OR OTHER COSTS DUE TO
INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE
NOT SPECIFICALLY STATED ABOVE. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY, ARE EXPRESSLY LIMITED TO
THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS, SO THE ABOVE
LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.
How to Obtain Service
To obtain repair service under this warranty, you must contact an authorized BRONDELL Service
Center to obtain an RMA (Return Merchandise Authorization) number. Proof of purchase in the form
of a copy of the original receipt must accompany the returned unit for the warranty to be valid. Take
or ship the unit pre-paid to the closest Brondell authorized service center along with the RMA number
and proof of purchase.
To obtain the RMA number and locate the BRONDELL Service Center location nearest you, please
call 1-888-542-3355.
15
CONTACT:
Brondell, Inc.
PO Box 470085
San Francisco, CA 94147-0085
Phone: 1-888-542-3355
Web: www.brondell.com
For questions, contact Brondell Customer Service: 1-888-542-3355
MANUFACTURED BY:
Brondell, Inc.
PO Box 470085
San Francisco, CA 94147-0085
Please retain receipt records for any warranty claims.
MANUAL DEL USUARIO
LH-22 Accesorio para el bidé
Temperatura Dual / Boquillas Duales
ÍNDICE
INFORMACIÓN DEL PRODUCTO
Características del producto .......... Página 17
Lista de piezas ...................... Página 18
Dimensiones del producto ............ Página 19
INSTALACIÓN DEL PRODUCTO
Antes de Instalación ................. Página 20
Conecte el suministro de agua fría ..... Página 21
Conecte el suministro de agua caliente Página 23
Instalar el accesorio bidé ............. Página 25
FUNCIONAMIENTO DEL PRODUCTO
Cómo utilizar el SouthSpa ............ Página 27
Posicionamiento de la boquilla ........ Página 27
MANTENIMIENTO
Limpiando el SouthSpa ............... Página 28
SI no uso a corto plazo ............... Página 28
GARANTÍA ......................... Página 29
CONTACTAR ........................ Página 30
VERSIÓN INGLÉS. . . . . . . . . . . . . . . . . . . . Página 1
VERSIÓN FRANCÉS ................. Página 31
17
CARACTERÍSTICAS DEL PRODUCTO
CARACTERÍSTICAS DEL PRODUCTO
Material ABS antibacterial de calidada alta con panel completo
Boquillas higiénicas y retráctiles
Función de autolimpieza de la boquilla
Lavado de bidé a temperaturas caliente y ambiente
Posicionamiento de la boquilla
Presión de agua adaptable
Válvula interna de núcleo de cerámica con construcción
“Uni-body” patentado por seguridad
Válvulas en T de 7/8" y 3/8" de alta calidad
Manguera de metal trenzado de bidé para la agua fría
Tubo flexible para agua caliente
No requiere energía eléctrica ni baterías
Fácil instalación y ajustable al inodoro
Todos los accesorios para una instalación estándar incluidosño
1 año de garantía
18
Accesorio para el bidé con perilla de control y soportes ajustables
INFORMACIÓN DEL PRODUCTO (cont.)
LISTA DE PIEZAS
Manguera de metal
trenzado de bidé
para la agua fría (25")
Válvula en T para
la agua fría
⁄" x ⁄" x ⁄"
Válvula en T para la
agua caliente con tapa
y conector de presión
⁄" x ⁄"
Arandelas grandes
de goma (2)
Arandelas pequeñas
de goma (2)
Tapa de suministro de
agua caliente
Tubo flexible para
agua caliente (1/4")
Tapa y conector de
presión para el
tubo flexible
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

brondell LH-20 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à