PROPOINT 9081605 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
V1.0 9081605
Please read and understand all instructions before use. Retain this manual for future reference.
SHOP PRESS
PNEUMATIC/HYDRAULIC
This page is intentionally left blank.
SPECIFICATIONS
Press Capacity 100,000 lb
Press Type Pneumatic/hydraulic
Ram Travel 7 in.
Working Range 5-1/8 to 34-11/16 in.
Bed Width 31-1/2 in.
Overall Height 65 in.
Pressure Rating 110 to 120 PSI
Material Steel Construction
INTRODUCTION
The workshop press is designed for light industrial use or for home
use. Perform straightening, stamping and bending with this powerful
hydraulic press. Features an H-frame design that makes it perfect for
removing or installing bearings, bushings, gears, ball joints, pulleys,
universal joints and more.
The press features a pneumatic foot control and a metal safety screen.
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic precautions
to reduce the risk of personal injury and/or damage to the
equipment.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could
result in a serious injury if the proper precautions are not taken.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 3 Assistance available at www.princessauto.com or 1-800-665-8685
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store unused tools properly in a dry, safe and secure location to
prevent rust, damage or misuse.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved
by the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply
with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate
matter.
3. Wear protective clothing and gloves designed for the work
environment, materials and tools.
4. Wear steel toe footwear or steel toe caps to prevent a foot injury
from falling objects.
5. The tool may contain high pressure. Use safety glasses and gloves
for protection during operation. Keep hands clear of the exposed
rubber portions of the hose.
6. The air source used with this tool may cause hearing damage.
Wear ear protection gear to eliminate or reduce the noise.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 4
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with
the moving parts of a tool. Keep long hair covered or bound.
3. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
4. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can
cause an injury.
5. Serious injury or death may occur from inhaling compressed air.
The air stream may contain carbon monoxide, toxic vapors or solid
particles. Never inhale compressed air directly from the pump or
air tool.
SPECIFIC SAFETY
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for an
unintended purpose.
2. The maximum load is 50 tons. Do not exceed this rated capacity.
Never apply excessive force to a workpiece and always use the
pressure gauge to accurately determine the applied load.
3. Inspect the press before each use. Do not use if any component
is bent, broken, cracked, leaking or showing other damage. Do not
use the press after a shock load until a qualified technician has
examined the press.
4. Check to ensure that all bolts and nuts are tight.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 5 Assistance available at www.princessauto.com or 1-800-665-8685
5. Only use this shop press on a surface that is stable, level and not
slippery. The surface must be capable of sustaining the weight of
the shop press and the load.
6. Ensure that the workpiece is center-loaded and secure. An
unbalanced load may slip off the heel blocks or bed frame.
7. Keep hands and feet away from the bed frame area at all times.
8. Do not use the shop press to compress a spring or any other item
that could disengage and cause a potential hazard. Never stand
directly in front of a loaded press and never leave a loaded press
unattended.
9. Do not allow an untrained person to operate the press.
10. Do not use brake fluid or other improper fluid in place of hydraulic
oil. Avoid mixing different types of oil when adding hydraulic oil.
Only good quality hydraulic jack oil can be used.
11. Do not expose the press to rain, snow or inclement weather.
12. Bolt the press to the floor if it is to be used on bulky or
unstable items.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch
or control. A power tool that fails to respond to the controls is
dangerous and can cause an injury. A qualified technician must
repair and verify the power tool is operating correctly, before it can
be used.
2. Shut the power off and disconnect the press from the power
supply (if possible) before making any adjustments, changing
accessories, cleaning, servicing or when storing. Such preventive
safety measures reduce the risk of starting the tool accidentally.
3. Check if the press's moving parts are misaligned or binding before
each use. Correct the issue before using the press to avoid an
injury or damage to the tool.
4. Avoid unintentional starts. Be sure that the regulator/throttle switch
is in the neutral or OFF position when not in use and before
connecting it to any air source.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 6
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic
fluid under pressure penetrates your skin. See Injection
Injury precautions for instructions before using a
pressurized hydraulic system.
1. Do not touch or handle, hydraulic hoses or components while
under pressure. Hydraulic fluid escaping under pressure has
sufficient force to penetrate your clothing and skin. A pinpoint hole
may inject hydraulic fluid into your body. Seek immediate medical
attention if this occurs (see Injection Injury).
2. Never exceed the hydraulic system’s load capacity (see
Specifications).
3. Do not adjust the hydraulic system’s relief setting. The settings are
preset by the factory.
4. Hydraulic oil under pressure is hot and can cause a burn injury
if touched, sprayed or spilled. Allow the hydraulic system to cool
before conducting maintenance.
5. Hydraulic components require regular inspection. Release all
pressure from the system before you inspect it. Replace damaged
hydraulic parts with identical manufacturer's components.
6. Do not attempt makeshift repairs to a hydraulic system. Such
repairs can fail suddenly and create a hazardous condition.
7. A damaged or disconnected hydraulic hose under pressure may
whip around and inflict personal injury or damage the work area.
Secure the hose to a fixed or permanent structure with clamps or
cable ties.
8. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do
not expose the fluid to an ignition source.
9. Change your clothing immediately if sprayed with hydraulic fluid.
Store clothing or rags contaminated with hydraulic fluid in an
approved metal safety can with a spring-closing lid and venting
designed to contain a fire.
10. Only use hydraulic fluid in the pump. Do not substitute or mix
brake fluid, or any other fluid, with the hydraulic fluid. This can
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 7 Assistance available at www.princessauto.com or 1-800-665-8685
result in a pump failure and injure the user or bystander. It may
also damage the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment
if fluid penetrates your skin. It may feel like a pricking or
sting. Do not wait for the appearance of symptoms. A toxic
reaction can occur from the exposure. Delay in treatment
can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon
as you arrive at the medical facility. The severity of the symptoms will
depend on the type of fluid injected. Bring the Safety Data Sheet for the
fluid with you to the medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under
pressure from the tool has sufficient force to penetrate your clothing
and skin. Follow the precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles,
rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a leak. Use a large piece of wood,
cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components
to ensure it is rated to handle the pressure.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate
control over the air supply in an emergency, even if a hose is
ruptured.
3. Discontinue tool use if it does not work properly or air is leaking.
Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.
4. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated
to never exceed the maximum pressure rating of the tool (see
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 8
Specifications). Exceeding the maximum PSI rating can create a
bursting hazard, causing injury and property damage.
a. The tool does not regulate the pressure level. The power
output is in direct proportion to the air pressure available. An
external air pressure regulator is required to safely use this
tool.
5. Never use oxygen, combustible gas or any other bottled gas as
a power source. Any power source other than an air compressor
could cause an explosion and serious personal injury.
6. Turn OFF the valve and discharge any remaining air pressure after
each use or before adjusting the tool.
7. Do not leave the air tool unattended with its compressed air supply
on. Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
8. Serious injury may occur from loose debris being propelled at
high speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air compressor.
9. Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
10. Do not cover the air vents.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing
is heard from the air hose or couplers. Replace the defective air
hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the
air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
a. Keep the air hose behind the tool and out of the tool's work
path.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 9 Assistance available at www.princessauto.com or 1-800-665-8685
b. Keep the air hose away from heat, oil, sharp edges or moving
parts.
c. Do not wrap the air hose around the tool as sharp edges may
pierce or crack the air hose. Gently coil the hose and either
hang on a hook or fasten with a device to keep hose together
when storing.
4. A damaged or disconnected air hose under pressure may whip
around and inflict personal injury or damage the work area. Secure
the compressor's air hose to a fixed or permanent structure with
clamps or cable ties.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage.
ASSEMBLY & INSTALLATION
INSTALL AN AIR COUPLER PLUG
Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use
with your tool.
1. Wrap the external threads of the coupler plug with sealant tape.
a. Wrap tape in a clockwise direction so it will not unravel.
b. Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the coupler plug into the tool's air inlet and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for
air leaks. Do not use the tool until all air leaks are repaired or the
faulty component is replaced.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 10
IMPORTANT! Vibration may cause failure if a quick coupler
is connected directly to the air tool. To overcome this,
connect a leader hose to the tool. A quick coupler may then
be used to connect the leader hose to the air line hose.
ASSEMBLY
Consult the parts list as necessary during assembly.
1. Lay both posts (#33 and 35) down on a flat surface. Move the wire
rope out of the way.
2. Position a base (#23) to align the center bolt holes with the post
bolt holes. Insert an M12x40 bolt (#18) through each bolt hole in
the base, post and bottom crossbeam. Secure each M12x40 bolt
with a M12 washer (#19), M12 lock washer (#20) and M12 nut
(#21) until hand-tight.
3. Position one base (#23) so the bolt holes align with the lower bolt
holes at the bottom of the left post. Insert an M12x40 bolt (#18)
through each bolt hole. Do not secure yet.
4. Position the lower cross beam (#22) over the protruding bolts.
The beam's apex faces up. Secure each bolt with an M12 washer
(#19), M12 lock washer (#20) and M12 nut (#21) until hand-tight.
5. Repeat on the other side.
6. Secure a strut (#17) to each end of a base with an M12x35 bolt
(#16), M12 washer, M12 lock washer and M12 nut until hand-tight.
7. Secure the free end of each strut to the second set of bolt holes
from the bottom with an M12x35 bolt, M12 washer, M12 lock
washer and M12 nut.
8. Tighten all nuts in steps 2 to 8 with a wrench.
9. Slide the upper crossbeam (#1) onto the posts and align the bolt
holes. Insert M22x70 bolts (#2) from the outside through all eight
bolt holes. Secure each bolt with an M22 washer (#3), M22 lock
washer (#4) and M22 nut (#5).
10. Raise the shop press frame upright.
11. Screw the pressure gauge (#45) and o-ring (#43) into the
connection nut (#42) of the three-way valve block (#38) through
the hole on the upper beam.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 11 Assistance available at www.princessauto.com or 1-800-665-8685
12. Connect one end of the long hydraulic hose (#36) to the
connection nut (#37) on the end of the three-way valve block.
13. Secure the pump with M10x20 bolts (#32) and M10 washers. The
bolts are inserted through the right post and into screw holes in the
pump’s mounting frame.
14. Connect the other end of the long hydraulic hose (#36) to the
pump's connection nut.
15. Hold the cylinder ram (#47) against the upper crossbeam's ram
base and align the bolt holes. You will need to either clamp the
ram in place or have another person assist you.
16. Insert an M16x75 bolt (#46) through a bolt hole from underneath.
Secure with an M16 washer (#48), M16 lock washer (#49) and M16
nut (#50). Repeat with the other three bolts. Tighten all nuts with a
wrench.
17. Connect the short hydraulic hose (#44) to the ram cylinder's
connection nut. Connect the other end to the 90° connection nut
(#39) on the three-way valve block (#38).
18. Connect the air pump's hose (#27) to the outlet port of the foot air
valve (#24).
• Follow the instructions for wrapping the threads with sealant
tape in Install an Air Coupler Plug.
19. Push each bed frame pin (#51) through the matching set of holes
on the left and right side of the frame. The bed frame will rest on
these, so ensure they are level with each other. Secure the pins
with the included clips (#52).
20. Position the bed frame (#10) so the beams are outside of the leg
assemblies. Lower until the bed frame is resting on the pins.
21. Install the rollers. Slide an M10 washer (#A7) onto an M10x35 bolt
(#A11), then a roller bushing (#A12) and a short bushing (#A13).
Screw the bolt into one of the inner bolt holes on the bed frame's
face. Repeat for the other 3 rollers.
22. Place an M10 washer (#A7) onto an M10x50 bolt (#A6) and insert
it in the top bolt hole of the left adjusting base. Place another M10
washer, then a bushing onto the protruding bolt. Prepare a second
bolt in the same manner.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 12
23. Position the left adjusting base (#A8) with the angled side to the
outside and the knob (#A10) on the inside. Screw the bolt into
the upper outer bolt hole on the bed frame's left side. Screw the
second bolt into the lower bolt hole.
24. Repeat steps 18 and 19 with the right adjusting base.
25. Place the screen handle (#A1) on the screen and align the bolt
holes. Insert an M6x20 bolt (#A4) through each bolt hole. Secure
each with an M6 washer (#A2) and M6 nut (#A3).
26. Slide the screen into place between the rollers until the height is
appropriate to protect the user during the task. Tighten the two
adjusting base knobs to hold the screen in place.
27. Insert the handle (#26) into the pump receiver for manual
operation.
28. Secure the winch (#13) with M10x30 bolts (#12) and M10 washers,
M10 nuts. Insert the bolts through the inner right-hand post and
into the screw holes in the winch’s mounting frame.
29. Check that the wire rope is properly seated in each pulley.
30. Wind the excess wire rope onto the winch. Make sure each
winding of the wire rope touches the previous winding. This
will prevent gaps that can trap the wire rope in the next layer.
Continue until the wire rope is under tension. Double-check for any
slackness in the wire rope and adjust as necessary.
31. Check all bolts and nuts and tighten if necessary.
OPERATIONS
BEFORE FIRST USE
Before the first use, check for proper hydraulic oil level in the system.
Then thoroughly test the hydraulic ram for proper operation prior to its
actual use.
1. Purge air from the hydraulic system. See Bleeding the Hydraulic
System in the Maintenance section.
2. Test the shop press without a workpiece to ensure all parts work
smoothly. Test again with a load. Gradually increase pressure and
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 13 Assistance available at www.princessauto.com or 1-800-665-8685
watch that the workload does not shift and there is no distortion or
deflection of the ram, leakage from the pump assembly or shifting
of the frame. A qualified technician should examine and repair any
problems with the pump itself.
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tool’s
air inlet, not the compressor’s outlet. Calculate the pressure drop for
your air supply set-up and increase the compressor outlet pressure to
compensate. Make sure you do not exceed the maximum pressure for
any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure
the air pressure and adjust the compressor’s output.
OPERATING THE PRESS
IMPORTANT! Ensure that you read, understand and apply
the safety instructions and warnings before use.
Manually add a drop or two of air tool oil into the tool’s coupler plug
before each use and after every hour of continuous use. The tool will
not work properly without lubrication and parts will wear prematurely.
1. Lift or lower the bed frame (#10) with the hand winch (#13) until
it is in position. Insert a bed frame pin (#51) into the left and right
posts beneath the bed frame. Lower the bed frame so it rests on
the bed frame pins.
2. Place the heel blocks (#34) on the bed frame, then insert a
workpiece on the heel blocks.
3. Close the release valve (#29) on the pump by turning it clockwise.
4. Pump the handle or pedal until the ram nears the workpiece.
5. Align the workpiece and ram to ensure center-loading.
6. Pump the handle or pedal to apply load onto the workpiece.
7. Do not exceed the maximum piston stroke. If you see a red line
on the piston, retract the ram and adjust the bed to bring the
workpiece closer to the ram.
8. Stop applying load to the workpiece when the task is complete.
9. Slowly and carefully remove load from workpiece by turning the
release valve counterclockwise in small increments.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 14
10. Once the ram has fully retracted, remove the workpiece from the
bed frame.
11. Close the release valve when you have finished for the day.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical replacement
parts when servicing.
3. Only use accessories intended for use with this tool. Follow
instructions for changing accessories.
4. Keep the tool handles or gripping surfaces clean and dry.
5. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd.
for replacements.
WARNING! Only qualified service personnel should repair
the tool. An improperly repaired tool may present a hazard
to the user and/or others.
HYDRAULIC RAM MAINTENANCE
Monthly maintenance is recommended for the hydraulic ram. Any
restrictions due to dirt, rust, etc. can cause the either slow movement or
extremely rapid jerks, damaging the internal components. The following
steps are designed to keep the pump maintained and operational.
1. Lubricate the cylinder and the pumping mechanism with light oil.
2. Visually inspect for cracked welds, bent, loose, missing parts or
hydraulic oil leaks.
3. Inspect the hydraulic ram immediately if it was subjected to an
abnormal load or shock load.
4. Remove any hydraulic jack pump from service that is damaged,
worn down or operates abnormally, until repaired by an authorized
service technician.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 15 Assistance available at www.princessauto.com or 1-800-665-8685
5. Check and maintain the ram oil level.
6. Always store the hydraulic ram in the fully retracted position. This
will help protect critical areas from corrosion.
7. Do not use brake or transmission fluids or regular motor oil as they
can damage the seals. Always purchase and use products labeled
Hydraulic Oil.
REPLACE THE HYDRAULIC OIL
Replace the hydraulic oil annually.
The oil can be removed by using a fluid extractor tool or detaching the
hydraulic pump from the press and manually emptying it.
FLUID EXTRACTOR TOOL
1. Retract the ram and remove the oil filler plug.
2. Follow the instructions for your fluid extractor tool to remove the old
hydraulic oil.
3. Follow the instructions for Refill the Hydraulic Pump.
MANUAL OIL REPLACEMENT
1. Relieve pressure from the system by loosening the oil filler plug.
2. Remove the pump from the press.
3. Remove the oil fill plug.
4. Lay the pump on its side and drain the oil into a suitable container.
Dispose of used hydraulic oil in accordance with local by-laws.
5. Stand the pump on its base and wipe off any excess oil.
6. Reinstall the hydraulic pump onto the press.
7. Follow the instructions for Refill the Hydraulic Pump.
REFILL THE HYDRAULIC JACK PUMP
The pump may become less efficient when the hydraulic oil level is too
low or contaminated by metal particulate through normal wear-and-tear.
1. Retract the ram and remove the oil filler plug.
2. Check and maintain the ram oil level.
• Check the oil level with the oil dip stick. Use a long plastic
cable tie as a substitute if the unit does not have a dipstick.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 16
3. Fill the cylinder with a high quality hydraulic jack oil, up to the oil
plug opening.
a. Place a funnel into the oil fill neck. The funnel opening should
be wide enough to prevent the oil from collecting in the
funnel’s cone.
b. Pour oil into the funnel. Allow the oil to settle for one minute
and recheck the level. Repeat until the desired level is
reached.
4. Follow the steps in Bleeding the Hydraulic System.
5. Insert the oil filler plug and hand tighten.
6. Wipe up any spilled oil. Dispose of oil soaked rags in a proper
hazardous waste container.
BLEEDING THE HYDRAULIC SYSTEM
Bleed excess air from the hydraulic system as follows:
1. Open the release valve by turning it counterclockwise.
2. Remove the oil filler screw and fill the hydraulic jack pump with
hydraulic fluid.
3. Wait 5 minutes for trapped air to rise to the surface.
4. Pump the handle or pedal for several strokes or press the air valve
trigger to eliminate any air in the system.
5. Check the oil filler hole and if necessary, top off with more
hydraulic oil.
6. Restore the oil filler screw. Close the release valve by turning
clockwise.
7. Test the ram several times for proper operation before putting it
into use. Do not use the ram if it still does not appear to be working
properly. Have a qualified service technician service or repair the
hydraulic system.
LUBRICATION
Inspect and lubricate the tool when required. Only use light oil to
lubricate the tool. Other lubricants may not be suitable and could
damage the tool or cause a malfunction during use.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 17 Assistance available at www.princessauto.com or 1-800-665-8685
Clean and lubricate all moving parts.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other
lubricants are not suitable and will damage the tool or cause
a malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool.
Penetrating oil acts as a solvent that will dissolve the tool’s
grease packing and may damage the o-rings, causing the
tool to seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a
generous amount of air tool oil in the air inlet and then run the tool
under no load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tool’s coupler
plug before each use and after every hour of continuous use. The
tool will not work properly without lubrication and parts will wear
prematurely.
3. Avoid adding too much air tool oil as this can cause premature
power loss and eventual tool failure. A qualified technician will
need to take the tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing
it for an extended period of time (overnight, weekend, etc.). Run
the tool for approximately 30 seconds to ensure the oil is evenly
distributed throughout the tool. Store it in a clean and dry location.
STORAGE
When not in use, store the press in a dry location with ram and piston
fully retracted.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws
for electronic devices, batteries, oil or other toxic liquids.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 18
DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
HYDRAULIC FLUID DISPOSAL
Do not drain hydraulic oil into the sewer system or dispose in an
uncontrolled location. Hydraulic fluid may take more than a year to
breakdown in the environment and the ingredients may still be toxic.
Contact your local municipality for proper disposal instructions or
locations.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
No oil flow. 1. Cylinder doesn’t
move.
2. Air lock in the lines.
3. No pressure reading
on gauge.
1. Check oil level. Fill as required.
2. Loosen fitting to bleed line.
3. Check pressure gauge. Replace if
defective.
a. Check control valve. Clean,
repair or replace as required.
b. Check cylinder seals. Oil
bypassing in cylinder. Replace
seals.
Oil on Press. 1. Oil leaking from
cylinder.
2. Oil leaking from
loose fitting or line.
1. Replace seals as required.
2. Tighten or add sealant as required.
a. Defective fitting. Replace.
V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081605
Page 19 Assistance available at www.princessauto.com or 1-800-665-8685
Problem(s) Possible Cause(s) Suggested Solution(s)
Cylinder ram
doesn’t move.
1. Hydraulic problems.
2. Press overloaded.
3. Ram jammed.
4. Ram binding.
5. Press efficiency
drops.
1. Check hydraulic system. Check
workpiece.
2. Exceeded capacity of Press. Use a
larger press.
3. Check cylinder. Remove defective
part and repair.
4. Cylinder ram is bent. Replace ram
and seals. Use more care when
applying loads.
5. Purge air from hydraulic system as
described in Bleeding the Hydraulic
System.
9081605 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0
Assistance available at www.princessauto.com or 1-800-665-8685 Page 20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
PROPOINT 9081605 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: PROPOINT 9081605 Owner's manual
Documents connexes
-
PROPOINT 9081548 Le manuel du propriétaire
-
-
-
-
-
-
Autres documents
-
Princess auto 9081563 Manuel utilisateur
-
Powerfist 9081555 Le manuel du propriétaire
-
-
-
-
-
-
-
-
