Greenlee DM-200A, DM-210A, DM-510A Digital Multimeters Manuel utilisateur

Catégorie
Mesure, test
Taper
Manuel utilisateur

Ce manuel convient également à

INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
52047798 REV 4 © 2019 Greenlee Tools, Inc. 10/19
Read and understand all of the instructions and safety information in this
manual before operating or servicing this tool.
Lea y entienda todas las instrucciones y la información sobre seguridad
que aparecen en este manual, antes de manejar estas herramientas o
darles mantenimiento.
Lire attentivement et bien comprendre toutes les instructions et les
informations sur la sécurité de ce manuel avant d’utiliser ou de procéder à
l’entretien de cet outil.
Register this product at www.greenlee.com / Registre este producto en www.greenlee.com
Enregistrez votre produit en ligne, www.greenlee.com
DM-200A • DM-210A
DM-510A
Digital Multimeters
Multímetros digitales
Multimètres
numériques
2
Description
The Greenlee DM-200A, DM-210A, and DM-510A Digital Multimeters are hand-held testing devices
with the following measurement capabilities: AC and DC voltage, AC and DC current, frequency, and
resistance. They also check diodes and verify continuity. An optional optically isolated computer inter-
face with software facilitates the recording of readings from the meter to a computer.
Other specialized capabilities and functions common to all meters include:
• Backlighted LCD for reading in dim conditions.
• Beep-Jack™ audible warning alerts the user with a beep and an error message on the LCD if the
test lead is plugged into the mA/μA or A input terminal while the selector switch is not in the mA/μA
or A position.
• Non-contact and single-probe voltage detection capability.
• Bar graph display, which responds more quickly than the numeric display — useful for detecting
faulty contacts, potentiometer clicks, and signal spikes.
• Relative zero mode.
• Data hold mode.
• Selectable automatic power off.
The DM-210A and DM-510A multimeters have the following additional capabilities: temperature
(K-type thermocouples only) and capacitance.
The DM-510A multimeter has an AutoCheck™ function for automatic selection of AC voltage, DC
voltage, and resistance with low input impedance to mask “ghost” voltages. The DM-510A also has a
crest function, which captures voltage or current signal peaks, as well as a recording function, which
stores the maximum and minimum input readings. The DM-510A is a true RMS meter.
Safety
Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction
manual and any markings on the tool provide information for avoiding hazards and unsafe practices
related to the use of this tool. Observe all of the safety information provided.
Purpose of This Manual
This instruction manual is intended to familiarize all personnel with the safe operation and maintenance
procedures for the Greenlee DM-200A, DM-210A, and DM-510A Digital Multimeters
Keep this manual available to all personnel. Replacement manuals are available upon request at no
charge at www.greenlee.com.
Do not discard this product or throw away!
For recycling information, go to www.greenlee.com.
DM-200A • DM-210A • DM-510A
3
SAFETY ALERT SYMBOL
This symbol is used to call your attention to hazards or unsafe practices which could result in an
injury or property damage. The signal word, defined below, indicates the severity of the hazard.
The message after the signal word provides information for preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result in severe injury or death.
Hazards which, if not avoided, COULD result in severe injury or death.
Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage.
Read and understand this material before operating or servicing this
equipment. Failure to understand how to safely operate this tool could result in
an accident causing serious injury or death.
Electric shock hazard:
Contact with live circuits could result in severe injury or death.
Important Safety Information
All specifications are nominal and may change as design improvements occur. Greenlee Tools, Inc. shall not be liable
for damages resulting from misapplication or misuse of its products.
® Registered: The color green for electrical test instruments is a registered trademark of Greenlee Tools, Inc.
AutoCheck and Beep-Jack are trademarks of BTC.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
KEEP THIS MANUAL
4
Important Safety Information
Electric shock and fire hazard:
• Do not expose this unit to rain or moisture.
• Do not use the unit if it is wet or damaged.
• Only use the test leads provided with the equipment or UL Listed Probe Assembly with same rating
or better.
• Inspect the test leads or accessory before use. They must be clean and dry, and the insulation
must be in good condition. Do not use the test lead if the contrasting inner layer of insulation is
visible.
• Use this unit for the manufacturer’s intended purpose only, as described in this manual. Any other
use can impair the protection provided by the unit.
Failure to observe these warnings could result in severe injury or death.
Electric shock hazard:
• Do not apply more than the rated voltage between any two input terminals, or between any input
terminal and earth ground.
• Do not contact the test lead tips or any uninsulated portion of the accessory.
Failure to observe these warnings could result in severe injury or death.
Electric shock hazard:
• Do not operate with the case open.
• Before opening the case, remove the test leads from the circuit and shut off the unit.
Failure to observe these warnings could result in severe injury or death.
Electric shock hazard:
The fuses are an integral part of the overvoltage protection. When fuse replacement is necessary,
refer to “Specifications” for the correct type, size, and capacity. Using any other type of fuse will void
the overvoltage protection rating of the unit.
Failure to observe this warning could result in severe injury or death.
DM-200A • DM-210A • DM-510A
5
Important Safety Information
Electric shock hazard:
• Unless measuring voltage, current, or frequency, shut off and lock out power. Make sure that all
capacitors are discharged. Voltage must not be present.
• Set the selector and connect the test leads so that they correspond to the intended measurement.
Incorrect settings or connections can result in a blown fuse.
• Using this unit near equipment that generates electromagnetic interference can result in unstable
or inaccurate readings.
Failure to observe these warnings could result in severe injury or death.
Electric shock hazard:
Do not change the measurement function while the test leads are connected to a component or
circuit.
Failure to observe this precaution may result in injury and can damage the unit.
Electric shock hazard:
Do not use the tester to measure voltages in circuits that could be damaged or activated by the
AutoCheck™ mode’s low input impedance (approximately 2.5 kΩ and 120 pF).
Failure to observe this precaution may result in injury and can damage the unit.
Electric shock hazard:
• Do not attempt to repair this unit. It contains no user-serviceable parts.
• Do not expose the unit to extremes in temperature or high humidity. Refer to “Specifications.”
Failure to observe these precautions may result in injury and can damage the unit.
6
Identification
1. Display 4-digit LCD (maximum reading is 5999) and bar graph.
2. Feature buttons Refer to explanations in the “Using the Features” section.
3. Selector Selects a function or turns power OFF.
4. ΩV Positive input terminal for all measurements except current.
5. COM Negative, common, or ground input terminal for all measurements.
6. A Positive input terminal for high current measurements.
7. mA µA Positive input terminal for low current measurements.
6
7
1
2
4
5
3
Symbols on the Unit
Warning—Read the instruction manual
Double insulation
DM-200A • DM-210A • DM-510A
7
13.
Bar graph element
14. Polarity indicator for bar graph
15. LoZ Low input impedance is active.
16. Low battery
17. Polarity indicator
18. 8.8.8.8 Numeric display
19. Relative zero function is enabled.
20. AC measurement is selected.
21. DC measurement is selected.
22. Automatic ranging is enabled.
23. Continuity
24. Hold function is enabled.
25. Crest capture function is enabled.
26. MAX Maximum is displayed or
being recorded.
MIN Minimum is displayed or
being recorded.
27. M Mega (10
6
)
28. Ω Ohm
29. k Kilo (10
3
)
30. Hz Hertz (frequency in
cycles per second)
31. n Nano (10
-9
)
32. F Farad
33. µ Micro (10
-6
)
34. m Milli (10
-3
)
35. V Volt
36. A Ampere
37. Bar graph scale
38. } Overload (bar graph display)
Display Icons
27-28
29-30
31-32
33-36
38
37
19
20-21
16
15
13-14
17
18
22 23 24 25 26
8
Using the Features
All Models
SELECT: Press momentarily to toggle between functions.
: Press and hold until backlight illuminates. Press and hold again to turn off. The backlight
automatically turns off after approximately 30 seconds to extend battery life.
RANGE: Press once to enter the manual ranging mode. The icon will disappear from the
display. Press repeatedly to step through the ranges. Press and hold to return to the automatic
ranging mode.
Note: When using MAX/MIN, HOLD, or ∆ mode, pressing RANGE will cause the meter to exit that
mode.
REL: Finds the difference between two measurements. While taking a measurement, press REL to
set the display to zero. The icon will appear on the display. Take the second measurement. The
value on the display will be the difference between the two measurements. Press again to exit this
mode.
Hz: Press and hold until the meter beeps to enable frequency measurement. The frequency function
can be used with the selector in any voltage or current setting. Use the V or A settings for measuring
the frequency of sinusoidal waveforms. Use the mV setting for measuring the frequency of 3 volt or
5volt logic level, square waveform signals.
The sensitivity of the frequency measurement function varies with the measurement range. To
automatically select a sensitivity level, measure the voltage or current first, and then press Hz. If the
reading becomes unstable or reads zero, press the RANGE button to select a different sensitivity
level.
The number of bar graph elements indicates the sensitivity selected:
• 1 element = 6 V, 6 A, 60 mA, or 600 µA
• 2 elements = 60 V, 10 A, 600 mA, or 6000 µA
• 3 elements = 600 V
• 4 elements = 1000 V
HOLD : Press momentarily to hold the present value on the display. Press again to exit this mode.
This feature does not affect the bar graph.
EF: Set the meter to any current or voltage function. Press and hold until the meter beeps to detect
the electric field that surrounds current-carrying conductors. Signal strength is displayed as a series
of dashes on the display.
• Use the tester’s built-in antenna (located along the top, near the LCD) for tracing live circuits or
locating a break in a wire.
• For more precision, such as distinguishing between current-carrying and ground wires, connect
a test lead to the ΩV
input terminal and use it as a probe for direct contact verification of AC
voltage.
Automatic Power Off: To extend battery life, the meter will shut itself off after approximately
30minutes of inactivity. To restore power, press either the SELECT, CREST, or REC button or turn the
selector to OFF and then back on. To disable this feature, press SELECT while turning the meter on.
DM-200A • DM-210A • DM-510A
9
Disabling the Beeper: Hold down the RANGE button while turning the meter on to temporarily
disable the beeper feature. Turn the selector to OFF and then back on to enable the beeper.
DM-510A Only
Low Impedance AutoCheck™ Mode: In this mode, the meter automatically selects the proper
measurement based on the input.
• If there is no input, “Auto” appears on the display.
• If the voltage is above approximately 1 volt AC or DC, voltage is displayed.
• If both AC and DC voltages are present, the larger voltage is displayed.
• If no voltage is present and there is resistance less than approximately 10 MΩ, resistance is
displayed. If the measured resistance is below the continuity threshold (between 10 Ω and 80 Ω),
then the continuity tone will sound.
This mode features low input impedance to mask stray or “ghost” voltage pickup. The input imped-
ance is approximately 2.5 kΩ at low voltage, increasing to approximately 375 kΩ at 1000 V.
The symbol “LoZ” indicates that the meter is in a low impedance mode. Do not use the AutoCheck™
mode on circuits that could be damaged or activated by such low input impedance. Instead use the
selector to select the high impedance AC or DC volts modes to minimize loading for such circuits.
Range-Lock and Function Feature: While in the AutoCheck™ mode, press the SELECT button
momentarily to lock the displayed function. Press the RANGE button momentarily to lock the dis-
played measurement range. Press either button repeatedly to step through the ranges or functions.
Energized Circuit Alert: If the resistance mode is locked in the AutoCheck™ mode and the leads
are placed across an energized circuit, the meter will emit an audible warning tone.
REC: Press momentarily to activate the MAX/MIN recording mode. The input value is measured
every 50 ms in this mode. “MAX MIN” will appear on the display. The LCD will display the actual
input value. The meter will beep whenever the maximum or minimum is updated. Press repeatedly to
select the desired display: maximum, minimum, or actual input. Press and hold to exit this mode.
The automatic power off feature is disabled when using this function.
CREST: Press momentarily to activate the crest recording mode. The input value is measured every
5 ms in this mode. and “MAX” will appear on the display. The LCD will display the maximum crest
value. Press repeatedly to select the desired display: maximum or minimum crest value. Press and
hold to exit this mode.
Automatic ranging and automatic power off are disabled when using this function.
Using the Features (cont’d)
10
AC Measurement
AC measurements are usually displayed as RMS (root mean square) values. The RMS value is equal to
the value of a DC waveform, which would deliver the same power if it replaced the time-varying wave-
form. Two AC measurement methods are average-responding RMS calibrated and true RMS-reading.
The average-responding RMS calibrated method takes the average value of the input signal after full
wave rectification, multiplies it by 1.11, and displays the result. This method is accurate if the input
signal is a pure sine wave. The DM-200A and DM-210A are average-responding meters.
The true RMS-reading method uses internal circuitry to read the true RMS value. This method is accu-
rate, within the specified crest factor limitations, whether the input signal is a pure sine wave, square
wave, triangle wave, half wave, or signal with harmonics. The ability to read true RMS provides much
more measurement versatility. The DM-510A is a true RMS meter.
The Waveforms and Crest Factors table shows some typical AC signals and their RMS values.
Waveforms and Crest Factors
Waveform
RMS Value 100 100 100 100
Average Value 90 100 87 64
Crest Factor*
(x)
1.414 1 1.73 2
* The crest factor is the ratio of the peak value to the RMS value; it is represented by the Greek
letter x.
DM-200A • DM-210A • DM-510A
11
Using the Optional Software
These meters are compatible with Greenlee DMSC-2U, an optically isolated computer interface cable
and software. It allows measurements to be logged to a personal computer using the Microsoft
®
Windows
®
operating system.
Installing the Software
1. Insert the CD into the computer’s CDROM drive.
2. The installation program should launch automatically. If it does not, double click on the CD icon in
“My Computer.”
3. The installation program menu will appear. Click on “Software Installation.”
4. Type your meter’s catalog number (for example, “DM-510A”) in the dialog box.
5. Complete the remaining dialog boxes according to user preferences.
6. Refer to the program’s Readme file for instructions on using the software.
Connecting the Optical Interface Cable
1. Align the interface with the slot on the back of the meter. The cable must point to the left.
2. Push the interface into the slot.
3. For USB applications, proceed to step 5.
4. For RS-232 applications, connect the interface cable to a serial port on the computer, and proceed
to step 8.
5. Connect the interface cable to the RS-232-to-USB adapter supplied with DMSC-2U.
6. Connect the square end of the USB cable to the RS-232-to-USB adapter.
7. Connect the other end of the USB cable to the computer.
8. Press the HOLD button while turning the meter on to enable its communication capabilities.
12
Operation
Electric shock hazard:
Contact with live circuits could result in severe injury or death.
1. Refer to the Settings Table. Set the selector to the proper setting, press SELECT (when instructed to
do so), and connect the test leads to the meter.
2. Refer to “Typical Measurements” for specific measurement instructions.
3. Test the unit on a known functioning circuit or component.
• If the unit does not function as expected on a known functioning circuit, replace the battery and/
or fuses.
• If the unit still does not function as expected, call Greenlee for technical assistance
at 800-435-0786.
4. Take the reading from the circuit or component to be tested.
Settings Table
To measure this
characteristic …
Set the
selector to this
symbol…
These icons will
appear on the
display …
Connect
the red
lead to…
Connect
the black
lead to …
All Models
Voltage
(1000 V max)
and V
ΩV COM
and V
Resistance
Ω
and press
SELECT
ΩV COM
Continuity*
and Ω
Diode
diod (momentarily)
and V
Voltage (600 mV max)**
mV
mV ΩV COM
Current (8A max)**
A mA
A, or
A COM
Current (600mA max)**
A mA
mA, or
mA µA COM
Current (6000µA max)**
µA
µA, or
mA µA COM
This table continues on the next page.
DM-200A • DM-210A • DM-510A
13
Operation (cont’d)
Settings Table (cont’d)
To measure this
characteristic …
Set the
selector to this
symbol…
These icons will
appear on the
display …
Connect
the red
lead to…
Connect
the black
lead to …
All Models (cont’d)
Frequency—Line Level
Voltage or Current
, A, mA, or µA
and press Hz
Hz ΩV COM
Frequency—Logic Level*** mV and press Hz Hz ΩV COM
EF
single probe†
Any voltage or
current function
and press EF for
at least 1 second
E.F.
ΩV
EF
non-contact†
DM-210A and DM-510A Only
Capacitance††
Ω
and press
SELECT
nF
Temp
ΩV
COM
Temperature Temp
C or F
(press SELECT to
change scale)
Temp
ΩV
COM
DM-510A Only
Auto select AC volts, DC volts,
resistance, and continuity (low
impedance measurement)
AutoCheck
and LoZ
Temp
ΩV
COM
* Tone indicates continuity. The threshold is between 10 Ω and 80 Ω.
** Press SELECT for AC or DC, as required.
*** Logic level frequency has a fixed sensitivity and is for digital signals. Refer to “Accuracy”.
Refer to the “Using the Features” section for an explanation of EF (electric field detection).
†† Discharge capacitor before measurement. Discharge a large capacitor through an appropriate
resistive load.
14
Typical Measurements
Voltage Measurement
Current Measurement
DM-200A • DM-210A • DM-510A
15
Typical Measurements
Continuity Check
Capacitance Measurement Diode Measurement
Forward Bias
Reverse Bias
Resistance Measurement
16
Typical Measurements
Temperature
Electric Field Detection (EF)
Refer to
“Using the Features”
for complete
instructions.
A–Non-contact
OR
B–Contact
A
B
DM-200A • DM-210A • DM-510A
17
Accuracy
Refer to the “Specifications” section for operating conditions and temperature coefficient.
Accuracy is specified as follows: ± (a percentage of the reading + a fixed amount) at 23 °C ± 5 °C
(73.4 °F ± 9 °F), 0% to 75% relative humidity.
True RMS Readings: DM-510A AC accuracies are specified from 5% to 100% of the range unless
otherwise specified. Frequency must be within the specified bandwidth for non-sinusoidal waveforms.
Crest factors are as follows:
• Crest factor < 3:1 at full scale
• Crest factor < 6:1 at half scale
All Models
AC Voltage DC Voltage
Range
(50 Hz to 400 Hz)
Accuracy Range Accuracy
60.00 mV ± (1.0% + 0.05 mV) 60.00 mV ± (0.4% + 0.05 mV)
600.0 mV ± (1.0% + 0.5 mV) 600.0 mV ± (0.2% + 0.3 mV)
6.000 V ± (1.0% + 0.005 V) 6.000 V ± (0.2% + 0.003 V)
60.00 V ± (1.0% + 0.05 V) 60.00 V ± (0.2% + 0.03 V)
600.0 V ± (1.0% + 0.5 V) 600.0 V ± (0.2% + 0.3 V)
1000 V ± (1.0% + 5 V) 1000 V ± (0.2% + 3 V)
Input Impedance: 10 MΩ // 50 pF
Accuracies for DM-510A are specified from
5% to 100% of range
Input Impedance: 10 MΩ // 50 pF
Resistance Diode Test
Measuring Range: 1.000 V
Test Current (typical): 0.56 mA
Open Circuit Voltage: < 1.8 VDC
Accuracy: ± (1.0% + 0.003 V)
Continuity
Tone Threshold: Between 10 Ω and 80 Ω
Response Time: < 32 ms
Range Accuracy
600.0 Ω ± (0.5% + 0.4 Ω)
6.000 kΩ ± (0.5% + 0.004 kΩ)
60.00 kΩ ± (0.5% + 0.04 kΩ)
600.0 kΩ ± (0.5% + 0.4k Ω)
6.000 MΩ ± (0.7% + 0.004 MΩ)
60.00 MΩ ± (1.2% + 0.04 MΩ)
Open Circuit Voltage: 0.45 VDC typical
18
AC Current
Range (50 Hz to 400 Hz) Accuracy Burden Voltage (typical)
600.0 µA ± (1.0% + 0.3 µA)
0.1 mV/µA
6000 µA ± (1.0% + 3 µA)
60.00 mA ± (1.0% + 0.03 mA)
1.7 mV/mA
600.0 mA ± (1.0% + 0.3 mA)
6.000 A ± (1.2% + 0.006 A)
0.03 V/A
8.00 A* ± (1.8% + 0.006 A)
Accuracies for DM-510A are specified from 5% to 100% of range
* 8 A continuous, > 8 A to 15 A for 30 second max with 5 minutes cool down interval
DC Current
Range Accuracy Burden Voltage (typical)
600.0 µA ± (0.5% +0.5 µA)
0.1 mV/µA
6000 µA ± (0.5% + 3 µA)
60.00 mA ± (0.5% + 0.05 mA)
1.7 mV/mA
600.0 mA ± (0.5% + 0.3 mA)
6.000 A ± (1.2% + 0.006 A)
0.03 V/A
8.00 A* ± (1.8% + 0.006 A)
*
8 A continuous, > 8 A to 15 A for 30 second max with 5 minutes cool down interval
Frequency —Hz (Line) at ACV, DCV, Current, AutoCheck™ Mode
Function Sensitivity (SineRMS) Range
6 V 0.4 V 10 Hz to 10 kHz
60 V 4 V 10 Hz to 50 kHz
600 V 40 V 10 Hz to 50 kHz
1000 V 400 V 45 Hz to 1 kHz
600 µA 40 µA 10 Hz to 10 kHz
6000 µA 400 µA 10 Hz to 10 kHz
60 mA 4 mA 10 Hz to 10 kHz
600 mA 40 mA 10 Hz to 10 kHz
6 A 1 A 10 Hz to 1 kHz
10 A 6 A 10 Hz to 1 kHz
Accuracy (cont’d)
All Models (cont’d)
DM-200A • DM-210A • DM-510A
19
Accuracy (cont’d)
All Models (cont’d)
Accuracy of Frequency Ranges
Display Range Accuracy
10.00 Hz to 65.53 Hz ± (0.03% + 0.03 Hz)
65.5 Hz to 655.3 Hz ± (0.03% + 0.3 Hz)
0.655 kHz to 6.553 kHz ± (0.03% + 0.003 kHz)
6.55 kHz to 50.00 kHz ± (0.03% + 0.03 kHz)
Frequency—Logic Level Hz (mV Function)
Range Accuracy
Sensitivity
(square wave)
5.0 Hz to 6.553 Hz ± (0.03% + 0.002 Hz)
3 V peak
6.55 Hz to 65.53 Hz ± (0.03% + 0.02 Hz)
65.5 Hz to 655.3 Hz ± (0.03% + 0.2 Hz)
0.655 kHz to 6.553 kHz ± (0.03% + 0.002 kHz)
6.55 kHz to 65.53 kHz ± (0.03% + 0.02 kHz)
65.5 kHz to 500.0 kHz ± (0.03% + 0.2 kHz)
500.0 kHz to 655.3 kHz ± (0.03% + 0.2 kHz)
5 V peak
0.655 MHz to 1.000 MHz ± (0.03% + 0.002 MHz)
Non-contact Electric Field Detection (EF)
Typical Voltage Bar Graph Indication* Frequency Range
10 V to 36 V
50 Hz to 60 Hz
23 V to 83 V – –
59 V to 165 V – – –
124 V to 330 V – – – –
250 V to 1000 V – – – – –
*
Bar graph indication and tone are proportional to signal strength
20
DM-210A and DM-510A Only
Capacitance Temperature
Range Accuracy Range Accuracy
60.00 nF ± (2.0% + 0.05 nF) -50 °C to 1000 °C ± (0.3% + 3 °C)
600.0 nF ± (2.0% + 0.5 nF) -58 °F to 1832 °F ± (0.3% + 6 °F)
6.000 µF ± (1.5% + 0.005 µF) The accuracy information is for the meter
only; refer to the information sheet provided
with the temperature probe (purchased
separately) for its accuracy
60.00 µF ± (1.5% + 0.05 µF)
600.0 µF ± (1.5% + 0.5 µF)
3000 µF ± (2.0% + 5 µF)
Accuracies are for film capacitors (capacitors
with negligible dielectric absorption);
measurements of larger capacitors can take
up to 30 seconds
DM-510A Only
AC Voltage AutoCheck™ Mode DC Voltage AutoCheck™ Mode
Range (50/60 Hz) Accuracy Range Accuracy
6.000 V ± (1.4% + 0.005 V) 6.000 V ± (1.3% + 0.003 V)
60.00 V ± (1.4% + 0.05 V) 60.00 V ± (1.3% + 0.03 V)
600.0 V ± (1.4% + 0.5 V) 600.0 V ± (1.3% + 0.3 V)
1000 V ± (1.4% + 5 V) 1000 V ± (1.3% + 3 V)
Input Impedance: Initial 2.5 kΩ // 120 pF
typical at voltages up to 50 V; increases with
voltage to approximately 375 kΩ at 1000 V
AutoCheck™ Trigger Level: > 1.0 V
(50/60Hz) typical
Input Impedance: Initial 2.5 kΩ // 120 pF
typical at voltages up to 50 V; increases with
voltage to approximately 375 kΩ at 1000 V
AutoCheck™ Trigger Level: > +1.0 VDC and
< -1.0 VDC typical
Resistance AutoCheck™ Mode Record Mode (Voltage and Current) for
recording signal maximums and minimums
≥ 100 ms in duration
Accuracy: Specified accuracy + 100 digits
Crest Capture (Voltage and Current) for
Crests ≥ 5 ms in duration
Accuracy: Specified accuracy ± 150 digits
Range Accuracy
600.0 Ω ± (1.2% + 1.0 Ω)
6.000 kΩ ± (1.2% + 0.010 kΩ)
60.00 kΩ ± (1.2% + 0.10 kΩ)
600.0 kΩ ± (1.2% + 1.0 kΩ)
6.000 MΩ ± (1.2% + 0.010 MΩ)
60.00 MΩ ± (1.2% + 0.10 MΩ)
Open Circuit Voltage: 0.45 VDC typical
AutoCheck™ Trigger Level: < 10.00 MΩ
typical
Accuracy (cont’d)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Greenlee DM-200A, DM-210A, DM-510A Digital Multimeters Manuel utilisateur

Catégorie
Mesure, test
Taper
Manuel utilisateur
Ce manuel convient également à