Hitachi CS33EB16 Manuel utilisateur

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand this

manual BEFORE operating the power tool. Please keep this manual available for other users and owners

before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de

sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de

lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la

disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi

doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede provocar lesiones

graves o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este

manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras

personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.

Model

Modèle

Modelo

CS 33EB

Chain Saw

Tronçonneuse

Motosierra

MEANINGS OF SYMBOLS

NOTE: Some units do not carry them.

Symbols

WARNING

The following show symbols used for the machine. Be sure that you understand

their meaning before use.

It is important that you read, fully understand and observe the following safety

precautions and warnings. Careless or improper use of the unit may cause

serious or fatal injury.

Read, understand and follow all warnings and instructions in this manual and on

the unit.

Always wear eye, head and ear protectors when using this unit.

Warning, kickback danger. Be careful of possible sudden and accidental upward

and/or backward motion of the guide bar.

One-handed usage not permitted. While cutting, hold saw ﬁ rmly with both hands

with thumb ﬁ rmly locked around front handle.

Contents

Parts breakdown

WHAT IS WHAT? ...................................................3

WARNINGS AND SAFETY INSTRUCTIONS .........4

SPECIFICATIONS ..................................................7

ASSEMBLY PROCEDURES ..................................8

OPERATING PROCEDURES .................................9

MAINTENANCE ...................................................15

2

English

WHAT IS WHAT?

1. Throttle trigger: Device activated by the

operatorʼs ﬁ nger, for controlling the engine

speed.

2. Throttle trigger lockout (Safety trigger): Device

that prevents the accidental operation of the

throttle trigger until manually released.

3. Ignition switch: Device for allowing the engine to

be started or stopped.

4. Oil tank cap: For closing the oil tank.

5. Recoil starter: Pull handle to start the engine.

6. Front handle: Support handle located at or

towards the front of the engine housing.

7. Fuel tank cap: For closing the fuel tank.

8. Choke control knob: Device for enriching the

fuel/air mixture in the carburetor, to aid starting.

9. Guide bar: The part that supports and guides the

saw chain.

10. Saw chain: Chain, serving as a cutting tool.

11. Chain brake (Front hand guard): Device for

stopping or locking the chain.

12. Spiked bumper (optional): Device for acting as a

pivot when in contact with a tree or log.

13. Chain catcher: device for restraining the saw

chain.

14. Guide bar cover: Device for covering the guide

bar and saw chain when the unit is not being

used.

15. Combi box spanner: The tool for removing or

installing a spark plug and tensioning the saw

chain.

16. Handling instructions: Included with unit. Read

before operation and keep for future reference to

learn proper, safe techniques.

11

10

9

13

8

2

6

5

1

3

7

4

14

12

15

16

3

English

WARNINGS AND SAFETY

INSTRUCTIONS

Operator safety

○ Always wear a safety face shield or goggles.

○ Always use the gloves to reduce the eﬀ ects of

vibration.

○ Gloves should be used when sharpening chain.

○ Always wear safety protective equipment such as

jacket, trousers, gloves, helmet, boots with steel

toe-caps and non-slip soles whenever you use a

chain saw. For working in trees the safety boots

must be suitable for climbing techniques. Do not

wear loose clothing, jewelry, short pants, sandals

or go barefoot.

Secure hair so it is above shoulder length.

○ Do not operate this tool when you are tired,

ill or under the inﬂ uence of alcohol, drugs or

medication.

○ Never let a child or inexperienced person operate

the machine.

○ Wear hearing protection. Pay attention to your

surroundings.

Be aware of any bystanders who may be

signaling a problem.

Remove safety equipment immediately upon

shutting oﬀ engine.

○ Wear head protection.

○ Never start or run the engine inside a closed

room or building.

Breathing exhaust fumes can kill.

○ For respiratory protection, wear a protection

mask while emitting the chain oil mist and dust

from sawdust.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting

equipment.

○ When the unit turned oﬀ , make sure the cutting

attachment has stopped before the unit is set

down.

○ When operation is prolonged, take a break from

time to time so that you may avoid possible

Hand-Arm Vibration Syndrome (HAVS) which is

caused by vibration.

○ The operator must obey the local regulations of

cutting area.

WARNING

● Antivibration systems do not guarantee that

you will not sustain Hand-Arm Vibration

Syndrome or carpal tunnel syndrome.

Therefore, continual end regular users

should monitor closely the condition of

their hands and ﬁ ngers. If any of the above

symptoms appear, seek medical advice

immediately.

● Long or continuous exposure to high

noise levels may cause permanent hearing

impairment. Always wear approved hearing

protection when operating a unit/machine.

● If you are using any medical electric/

electronic devices such as a pacemaker,

consult your physician as well as the device

manufacturer prior to operating any power

equipment.

Unit/machine safety

○

Inspect the entire unit/machine before each use.

Replace damaged parts. Check for fuel leaks and

make sure all fasteners are in place and securely

tightened.

○

Replace parts that are cracked, chipped or

damaged in any way before using the unit/

machine.

○ Make sure the side case is properly attached.

○ Keep others away when making carburetor

adjustments.

○

Use only accessories as recommended for this

unit/machine by the manufacturer.

○

Never let the chain strike any obstacle. If the

chain makes contact, the machine should be

stopped and checked carefully.

○ Make sure the automatic oiler is working. Keep

the oil tank ﬁ lled with clean oil. Never let chain

run dry on the bar.

○ All chain saw service, other than the items listed

in the operatorʼs/ ownerʼs manual, should be

performed by competent chain-saw service

personnel. (For example, if improper tools are

used to remove the ﬂ ywheel or if an improper tool

is used to hold the ﬂ ywheel in order to remove the

clutch, structural damage to the ﬂ ywheel could

occur and could subsequently cause the ﬂ ywheel

to burst.)

WARNING

● Never modify the unit/machine in any way.

Do not use your unit/machine for any job

except that for which it is intended.

● Never use chain saw without any safety

equipment or that has faulty safety

equipment. It could result in serious personal

injury.

● Using guide bar/chain other than

recommended by the manufacturer which

are not approved, could result in a high risk

of personal accidents or injury.

4

English

Fuel safety

○ Mix and pour fuel outdoors and where there are

no sparks or ﬂ ames.

○ Use a container approved for fuel.

○ Do not smoke or allow smoking near fuel or the

unit/machine or while using the unit/machine.

○ Wipe up all fuel spills before starting engine.

○ Move at least 3 m away from fueling site before

starting engine.

○ Stop engine before removing fuel cap.

○ Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be

emptied after each use. If fuel is left in the tank,

store so fuel will not leak.

○ Store unit/machine and fuel in area where fuel

vapors cannot reach sparks or open ﬂ ames

from water heaters, electric motors or switches,

furnaces, etc.

WARNING

Fuel is easy to ignite or get explosion or

inhale fumes, so that pay special attention

when handling or ﬁ lling fuel.

Cutting safety

○ Do not cut any material other than wood or

wooden objects.

○ For respiratory protection, wear an aerosol

protection mask when cutting the wood after

insecticide has been applied.

○ Keep others including children, animals,

bystanders and helpers outside the hazard

zone. Stop the engine immediately if you are

approached.

○ Hold the unit/machine ﬁ rmly with the right hand

on the rear handle and the left hand on the front

handle.

○ Keep ﬁ rm footing and balance. Do not over-

reach.

○ Keep all parts of your body away from the muﬄ er

and cutting attachment when the engine is

running.

○ Keep Bar/Chain below waist level.

○ Before felling a tree, the operator must be

accustomed to the sawing techniques of the

chain saw.

○ Be sure to pre-plan a safe exit from a failing tree.

○ While cutting, hold saw ﬁ rmly with both hands

with thumb ﬁ rmly locked around front handle,

and stand with feet well balanced and your body

balanced.

○ Stand to the side of the saw when cutting - never

directly behind it.

○ Always keep the spiked bumper face to a tree,

because the chain may suddenly be drawn into a

tree, if so equipped.

○ When completing a cut, be ready to hold up the

units as it breaks into clear, so it will not follow

through and cut your legs, feet or body, or contact

an obstruction.

○ Be alert against kickback (when saw kicks up and

back at operator). Never cut with the nose of the

bar.

○ When relocating to a new work area, be sure to

shut oﬀ the machine and ensure that all cutting

attachments are stopped.

○

Never place the machine on the ground when

running.

○

Always ensure that the engine is shut oﬀ and any

cutting attachments have completely stopped

before clearing debris or removing grass from the

cutting attachment.

○ Always carry a ﬁ rst-aid kit when operating any

power equipment.

○ Never start or run the engine inside a closed

room or building and/or near the inﬂ ammable

liquid. Breathing exhaust fumes can kill.

Maintenance safety

○ Maintain the unit/machine according to

recommended procedures.

○ Disconnect the spark plug before performing

maintenance except for carburetor adjustments.

○ Keep others away when making carburetor

adjustments.

○ Use only genuine HITACHI replacement parts as

recommended by the manufacturer.

CAUTION

Do not disassemble the recoil starter. You

may get a possibility of personal injury with

recoil spring.

WARNING

Improper maintenance could result in serious

engine damage or in serious personal injury.

Transport and storage

○ Carry the unit/machine by hand with the engine

stopped and the muﬄ er away from your body.

○ Allow the engine to cool, empty the fuel tank,

and secure the unit/machine before storing or

transporting in a vehicle.

○ Empty the fuel tank before storing the unit/

machine. It is recommended that the fuel be

emptied after each use. If fuel is left in the tank,

store so fuel will not leak.

5

English

○ Store unit/machine out of the reach of children.

○ Clean and maintain the unit carefully and store it

in a dry place.

○ Make sure engine switch is oﬀ when transporting

or storing.

○ When transporting in a vehicle or storage, cover

chain with chain cover.

If situations occur which are not covered in this

manual, take care and use common sense. Contact

HITACHI dealer if you need assistance. Pay special

attention to statements preceded by the following

words:

WARNING

Indicates a strong possibility of severe

personal injury or loss of life, if instructions

are not followed.

CAUTION

Indicates a possibility of personal injury or

equipment damage, if instructions are not

followed.

NOTE

Helpful information for correct function and use.

6

English

SPECIFICATIONS

Model

CS33EB (30P) CS33EB (35P) CS33EB (40P)

CS33EB

Type of equipment Chain saw, portable

Engine Size (cu. in.) 1.96 (32.2 ml)

Spark Plug NGK BPM-6A or equivalent

Fuel Tank Capacity (US pint) 0.74 (350 ml)

Chain Oil Tank Capacity (US pint) 0.53 (250 ml)

Dry Weight (lbs)

(Without guide bar and chain)

8.4 (3.8 kg)

Guide bar length (in.) 12 (300 mm) 14 (350 mm)

16

(400 mm)

—

Chain pitch (in.) 3/8 (9.52 mm)

Chain gauge (in.) 0.05 (1.27 mm)

Sound pressure level

LpA (dB (A))

by ISO 22868

92

Sound power level

Lw measured (dB (A))

by ISO 22868

Sound power level LwA (dB (A))

by 2000/14/EC

110

113

Vibration level (m/s

2

)

by ISO 22867

Front handle

Rear handle

8.5

8.0

9.2

6.7

9.7

6.7

—

Max. engine power

by ISO 7293 (kW)

1.2/9,500

Max. engine speed (min

-1

) 12,500

Idle engine speed (min

-1

) 3,100

Speciﬁ c fuel consumption (g/kWh) 500

Type of chain

91VG

(Oregon)

Max. chain speed (m/sec) 23.8

Sprocket (number of teeth) 6

NOTE: Equivalent noise level/vibration levels are calculated as the time-weighted energy total for noise/

vibration levels under various working conditions with the following time distribution: 1/3 idle, 1/3 full,

1/3 racing speed.

* All data subject to change without notice.

7

English

ASSEMBLY PROCEDURES

WARNING

Never try to start engine without side case

securely fastened.

1. Remove chain bar clamp nuts (1).

2. Remove the side case (2) as pinching the rear

part of the side case (2). (Fig. 1)

2

1

Fig. 1

* In case of installing the spiked bumper (3),

install the spiked bumper (3) (if so equipped) to

the unit with two screws. (Fig. 2)

3

Fig. 2

3. Install the chain bar (4) onto the bolts (5), then

push it toward the sprocket (6) as far as it will go.

Make sure that the boss of chain tension adjust

bolt (7) ﬁ ts into the hole of the bar (8). (Fig. 3)

6

4

5

8

7

Fig. 3

NOTE

Slightly move the bar back and forth and make

sure the chain tension boss (7) ﬁ ts into the hole

(8) in the bar properly. (Fig. 3)

4. Conﬁ rm the direction of saw chain (9) is correct

as in the ﬁ gure, and align the chain on the

sprocket. (Fig. 4)

9

Fig. 4

5. Guide the chain drive links into the bar groove all

around the bar.

6. Install the side case (2) onto the bolts (5).

Then tighten the clamp nuts (1) temporarily.

(

Fig. 1

)

7. Raise the bar end, and tighten the chain (9)

by turning the tension adjustment bolt (10)

clockwise. To check proper tension, lightly lift

up the center of chain and there should be about

0.02 – 0.04 ″ (0.5 – 1.0 mm) clearance between

bar and edge of drive link (11). (Fig. 5, 6)

9

11

10

0.02 – 0.04 ″

(0.5 – 1 mm)

Fig. 5

Fig. 6

8

English

CAUTION

PROPER TENSION IS EXTREMELY

IMPORTANT

8. Raise the bar end and securely tighten the chain

bar clamp nuts with the combi box spanner.

(Fig. 6)

9. A new chain will stretch so adjust the chain after

a few cuts and watch chain tension carefully for

the ﬁ rst half hour of cutting.

NOTE

Check the chain tension frequently for optimum

performance and durability.

CAUTION

● When the chain is excessively tightened,

the bar and chain will be damaged rapidly.

Conversely, when the chain is excessively

loosened, it may get out of the groove in the

bar.

● Always wear gloves when touching the

chain.

WARNING

During operation, hold chain saw ﬁ rmly with

both hands. A single hand operation may

cause serious injury.

OPERATING PROCEDURES

Fuel (Fig. 7)

Fig. 7

WARNING

● The chain saw is equipped with a two-stroke

engine. Always run the engine on fuel, which

is mixed with oil. Provide good ventilation,

when fueling or handling fuel.

● Fuel contains highly ﬂ ammable and it is

possible to get the serious personal injury

when inhaling or spilling on your body.

Always pay attention when handling fuel.

Always have good ventilation when handling

fuel inside building.

Fuel

○

Always use branded 89 octane unleaded

gasoline.

○ Use genuine two-cycle oil or use a mix between

25:1 to 50:1, please consult the oil bottle for the

ratio or HITACHI dealer.

○ Only for the state of California at 50:1.

○ If genuine oil is not available, use an anti-oxidant

added quality oil expressly labeled for air-cooled

2-cycle engine use (JASO FC GRADE OIL or ISO

EGC GRADE). Do not use BIA or TCW (2-stroke

water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Always mix fuel and oil in a separate clean

container.

Always start by ﬁ lling half the amount of gasoline,

which is to be used.

Then add the whole amount of oil. Mix (shake) the

fuel mixture. Add the remaining amount of gasoline.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the

fuel tank.

Fueling

WARNING (Fig. 8)

● Always shut oﬀ the engine before refueling.

● Slowly open the fuel tank (12), when ﬁ lling

up with fuel, so that possible overpressure

disappears.

● Tighten the fuel cap carefully, after fueling.

● Always move the unit at least 10 ft. (3 m)

from the fueling area before starting.

● Always wash any spilled fuel from clothing

immediately with soap.

● Be sure to check any fuel leaking after

refueling.

13

12

Fig. 8

Before fueling, clean the tank cap area carefully,

to ensure that no dirt falls into the tank. Make sure

that the fuel is well mixed by shaking the container,

before fueling.

9

English

Chain oil (Fig. 8)

Fill up with chain oil (13). Always use good quality

chain oil. When the engine is running, the chain oil is

automatically discharged.

NOTE

When pouring fuel (12) or chain oil (13) into the

tank, place the unit with cap side up. (Fig. 8)

Starting (Fig. 9, 10)

CAUTION

Before starting, make sure chain brake is

disengaged (if so equipped) and that the bar/

chain does not touch anything.

1. Set ignition switch (14) to ON position. (Fig. 9)

14

Fig. 9

2. Pull the choke lever (15) down to choked position

(Fig. 10). This will automatically lock the throttle in

starting position. (Fig. 9)

15

Fig. 10

3. Pull recoil starter briskly, taking care to keep the

handle in your grasp and not allowing it to snap

back. (Fig. 9)

4. When you hear ﬁ rst ignition, return the choke to

run position. (Fig. 10)

5. Pull recoil starter briskly again in the

aforementioned manner. (Fig. 11)

After engine starts, make sure the chain brake is

disengaged.

Fig. 11

NOTE

If engine does not start, repeat procedures from

2 to 5.

6. After starting engine, allow the engine about 2–3

minutes to warm up before subjecting it to any

load.

Chain brake operation (Fig. 12)

Chain brake (16), if so equipped, is designed to

activate in an emergency such as kick-back action.

Please check to verify that it works properly before

use.

Application of brake is made by moving the front

guard towards the bar. During the chain brake

operation, even if the throttle lever is pulled, the

engine speed does not increase and the chain does

not turn. To release the brake, pull up the chain

brake lever.

16

Fig. 12

How to conﬁ rm:

1) Turn oﬀ the engine.

2) Holding the chain saw horizontally, release your

hand from the front handle, hit the tip of the guide

bar to a stump or a piece of wood, and conﬁ rm

brake operation. Operating level varies by bar

size.

10

English

In case the brake is not eﬀ ective, ask our dealer for

inspection and repairs. If the engine keeps rotating

at high speed with the brake engaged, the clutch will

overheat causing trouble.

When the brake engages during operation,

immediately release the throttle lever to stop the

engine.

WARNING

Do not carry the machine with the engine

running.

Stopping (Fig. 13)

Decrease engine speed, and push ignition switch

(14) to stop position.

14

Fig. 13

WARNING

KICKBACK DANGER (Fig. 14)

17

Fig. 14

One of the most severe dangers when working with

a chain saw is the possibility of kickback. Kickback

may occur when the upper tip of the guide bar

touches an object, or when the wood closes in

and pinches the saw chain in the cut. Tip contact

in some cases may cause a lightning fast reverse

reaction, kicking the guide bar up and back toward

you. Pinching the saw chain along the top of the

guide bar may also push the guide bar rapidly back

towards you. Either of these reactions may cause

you to lose control of the saw which could result in

serious personal injury. Even though your saw has

safety built into its design, you should not rely on

these safety features exclusively. Know where your

bar tip is at all times. Kickback does occur if you

allow the kickback zone (17) of the bar to touch an

object. Do not use that area. Kickback from pinching

is caused by a cut closing and pinching the upper

side of the guide bar. Study your cut and make sure

it will open as you cut through. Maintain control when

the engine is running by always keeping a ﬁ rm grip

on the saw with your right hand on the rear handle,

your left hand on the front handle and your thumbs

and ﬁ ngers encircling the handles. Always hold the

saw with both hands during operation and cut at high

engine speed.

WARNING

● Do not overreach or cut above shoulder

height.

● Use extra caution when felling, and do not

use the saw in a nose-high position or above

shoulder height.

CHAIN CATCHER

The chain catcher is located on the power head just

below the chain to further prevent the possibility of a

broken chain striking the chain saw user.

WARNING

Do not stand in-line with chain when cutting.

BASIC TECHNIQUES FOR MAKING FELLING,

LIMBING AND BUCKING CUTS

The intention of the following information is to

provide you with the general introduction to wood

cutting techniques.

WARNING

● This information does not cover all speciﬁ c

situations, which may depend on diﬀ erences

in terrain, vegetation, kind of wood, form

and size of trees, etc. Consult your servicing

dealer, forestry agent or local forestry

schools for advice on speciﬁ c woodcutting

problems in your area. This will make your

work more eﬃ cient and safer.

● Avoid cutting in adverse weather conditions,

such as dense fog, heavy rain, bitter cold,

high winds, etc.

Adverse weather is often tiring to work in

and creates potentially dangerous conditions

such as slippery ground.

11

English

High winds may force the tree to fall in an

unexpected direction causing property

damage or personal injury.

CAUTION

Never use a chain saw to pry or for any

purpose for which it is not intended.

WARNING

● Avoid stumbling on obstacles such as

stumps, roots, rocks, branches and fallen

trees. Watch out for holes and ditches. Be

extremely cautious when working on slopes

or uneven ground.

Shut oﬀ the saw when moving from one work

place to another.

Always cut at wide open throttle. A slow

moving chain can easily catch and force the

saw to jerk.

● Never use the saw with only one hand.

You cannot control the saw properly and

you may lose control and injure yourself

severely.

Keep the saw body close to your body to

improve control and reduce strain.

When cutting with the bottom part of the

chain the reactive force will pull the saw

away from you towards the wood you are

cutting.

The saw will control the feeding speed and

sawdust will be directed towards you. (Fig.

15)

Fig. 15

● When cutting with the upper part of the chain

the reactive force will push the saw towards

you and away from the wood you are cutting.

(Fig. 16)

Fig. 16

● There is a risk of kickback if the saw is

pushed far enough so that you begin to cut

with the nose of the bar.

The safest cutting method is to cut with the

bottom part of the chain. Sawing with the

upper part makes it much more diﬃ cult to

control the saw and increases the risk of

kickback.

● In case the chain locked, immediately release

the throttle lever.

If the throttle lever keeps rotating at high

speed with the chain locked, the clutch will

overheat causing trouble.

NOTE

Always keep the spiked bumper face to a tree,

because the chain may suddenly be drawn into a

tree.

FELLING

Felling is more than cutting down a tree. You must

also bring it down as near to an intended place as

possible without damaging the tree or anything else.

Before felling a tree, carefully consider all conditions

which may eﬀ ect the intended direction, such as:

Angle of the tree. Shape of the crown. Snow load on

the crown.

Wind conditions. Obstacles within tree range (e.g.,

other trees, power lines, roads, buildings, etc.).

WARNING

● Always observe the general conditions of

the tree. Look for decay and rot in the trunk

which will make it more likely to snap and

start to fall before you expect it.

● Look for dry branches, which may break and

hit you when you are working.

Always keep animals and people at least

twice the tree length away while felling. Clear

away shrubs and branches from around the

tree.

Prepare a path of retreat away from the

felling direction.

BASIC RULES FOR FELLING TREES

Normally the felling consists of two main cutting

operations, notching and making the felling cut. Start

12

English

making the upper notch cut on the side of the tree

facing the feeling direction. Look through the kerf as

you saw the lower cut so you do not saw too deep

into the trunk. The notch should be deep enough to

create a hinge of suﬃ cient width and strength. The

notch opening should be wide enough to direct the

fall of the tree as long as possible. Saw the felling

cut from the other side of the tree between one and

two inches (3–5 cm) above the edge of the notch.

(Fig. 17)

18

19

20

21

Fig. 17

18. Felling direction

19. 45° minimum notch opening

20. Hinge

21. Felling cut

Never saw completely through the trunk. Always

leave a hinge.

The hinge guides the tree. If the trunk is completely

cut through, you lose control over the felling

direction.

Insert a wedge or a felling lever in the cut well before

the tree becomes unstable and starts to move. This

will prevent the guide bar from binding in the felling

cut if you have misjudged the falling direction. Make

sure no people have come into the range of the

falling tree before you push it over.

FELLING CUT, TRUNK DIAMETER MORE THAN

TWICE GUIDE BAR LENGTH

Cut a large, wide notch. Then cut a recess into the

center of the notch. Always leave a hinge on both

sides of the center cut. (Fig. 18)

Fig. 18

Complete the felling cut by sawing around the trunk

as in the Fig. 19.

Fig. 19

WARNING

These methods are extremely dangerous

because they involve the use of the nose of

guide bar and can result in kickback.

Only properly trained professionals should

attempt these techniques.

LIMBING

Limbing is removing the branches from a feller tree.

WARNING

A majority of kickback accidents occur

during Iimbing.

Do not use the nose of the guide bar. Be

extremely cautious and avoid contacting the

log, other limbs or objects with the nose of

the guide bar. Be extremely cautious of limbs

under tension. They can spring back towards

you and cause loss of control resulting in

injury. (Fig. 20)

Fig. 20

Stand on the left side of the trunk. Maintain a secure

footing and rest the saw on the trunk. Hold the saw

close to you so that you are in full control of it. Keep

well away from the chain. Move only when the trunk

is between you and the chain. Watch out for spring

back of limbs under tension.

13

English

LIMBING THICK BRANCHES

When limbing thick branches, the guide bar may get

pinched easily. Branches under tension often snap

up, so cut troublesome branches in small steps.

Apply the same principles as for cross cutting. Think

ahead and be aware of the possible consequences

of all your actions.

CROSS CUTTING/BUCKING

Before starting to cut through the log, try to imagine

what is going to happen. Look out for stresses in

the log and cut through it in such a manner that the

guide bar will not get pinched.

CROSS CUTTING LOGS, PRESSURE ON TOP

Take a ﬁ rm stance. Begin with an upper cut. Do

not cut too deeply, about 1/3 of the log diameter is

enough. Finish with a bottom cut.

The saw cuts should meet. (Fig. 21)

24

22

25

26

23

27

Fig. 21

22. Relieving cut

23. Cross cut

24. Pressure on top

25. Pressure side

26. Tension side

27. Relative depth of saw cuts

THICK LOG, LARGER THAN GUIDE BAR

LENGTH

Begin by cutting on the opposite side of the log.

Pull the saw towards you, followed by previous

procedure. (Fig. 22)

Fig. 22

If the log is lying on the ground make a boring cut to

avoid cutting into the ground. Finish with a bottom

cut. (Fig. 23)

Fig. 23

WARNING

KICKBACK DANGER

Do not attempt a boring cut if you are not

properly trained. A boring cut involves the

use of the nose of the guide bar and can

result in kickback.

CROSS CUTTING LOGS, PRESSURE ON

BOTTOM

Take a ﬁ rm stance. Begin with a bottom cut. The

depth of the cut should be about 1/3 of the log

diameter.

Finish with an upper cut. The saw cuts should meet.

(Fig. 24)

30

29

31

32

28

33

Fig. 24

28. Relieving cut

29. Cross cut

30. Pressure on bottom

31. Tension side

32. Pressure side

33. Relative depth of saw cuts

THICK LOG, LARGER THAN GUIDE BAR

LENGTH

Begin by cutting on the opposite side of the log.

Pull the saw towards you, followed by previous

procedure. Make a boring cut if the log is close to

the ground. Finish with a top cut. (Fig. 25)

14

English

Fig. 25

WARNING

KICKBACK DANGER

Do not attempt a boring cut if you are not

properly trained. A boring cut involves the

use of the nose of the guide bar and can

result in kickback. (Fig. 26)

Fig. 26

IF THE SAW GETS STUCK

Stop the engine. Raise the log or change its position,

using a thick branch or pole as a lever. Do not try

to pull the saw free. If you do, you can deform the

handle or be injured by the saw chain if the saw is

suddenly released.

MAINTENANCE

MAINTENANCE, REPLACEMENT OR REPAIR

OF THE EMISSION CONTROL DEVICES AND

SYSTEM MAY BE PERFORMED BY ANY NON-

ROAD ENGINE REPAIR ESTABLISHMENT OR

INDIVIDUAL.

Carburetor adjustment (Fig. 27)

Fig. 27

WARNING

Never start the engine without the complete

clutch cover.

Otherwise the clutch can come loose and

cause personal injuries.

In the carburetor, fuel is mixed with air. When the

engine is test run at the factory, the carburetor is

adjusted. A further adjustment may be required,

according to climate and altitude. The carburetor has

one adjustment possibility:

T = Idle speed adjustment screw.

Idle speed adjustment (T)

Check that the air ﬁ lter is clean. When the idle

speed is correct, the cutting attachment will not

rotate. If adjustment is required, close (clockwise)

the T-screw, with the engine running, until the

cutting attachment starts to rotate. Open (counter-

clockwise) the screw until the cutting attachment

stops. You have reached the correct idle speed

when the engine runs smoothly in all positions well

below the rpm when the cutting attachment starts to

rotate.

If the cutting attachment still rotates after idle speed

adjustment, contact HITACHI dealer.

WARNING

When the engine is idling the cutting

attachment must under no circumstances

rotate.

NOTE

Some models sold in areas with strict exhaust

emission regulation do not have high and low

speed carburetor adjustments. Such adjustments

may allow the engine to be operated outside

of their emission compliance limits. For these

models, the only carburetor adjustment is idle

speed.

15

English

If you are not familiar with this type of adjustment,

please ask for assistance from your HITACHI dealer.

Air ﬁ lter (Fig. 28)

The air ﬁ lter (34) must be cleaned from dust and dirt

in order to avoid:

○ Carburetor malfunctions.

○ Starting problems.

○ Engine power reduction.

○ Unnecessary wear on the engine parts.

○ Abnormal fuel consumption.

Clean the air ﬁ lter daily or more often if working in

exceptionally dusty areas.

Cleaning the air ﬁ lter

Remove the air ﬁ lter cover (35) and the ﬁ lter (34).

35

34

Fig. 28

Rinse them in warm soap suds. Check that the ﬁ lter

is dry before reassembly. An air ﬁ lter that has been

used for some time cannot be cleaned completely.

Therefore, it must regularly be replaced with a new

one. A damaged ﬁ lter must always be replaced.

Spark plug (Fig. 29)

The spark plug condition is inﬂ uenced by:

○ An incorrect carburetor setting.

○ Wrong fuel mixture (too much oil in the gasoline)

○ A dirty air ﬁ lter.

○ Hard running conditions (such as cold weather).

These factors cause deposits on the spark plug

electrodes, which may result in malfunction and

starting diﬃ culties. If the engine is low on power,

diﬃ cult to start or runs poorly at idling speed, always

check the spark plug ﬁ rst. If the spark plug is dirty,

clean it and check the electrode gap. Readjust if

necessary. The correct gap is 0.024″ (0.6 mm).

The spark plug should be replaced after about 100

operation hours or earlier if the electrodes are badly

eroded.

0.024 ″

(0.6 mm)

Fig. 29

NOTE

In some areas, local law requires using a resistor

spark plug to suppress ignition signals. If this

machine was originally equipped with resistor

spark plug, use same type of spark plug for

replacement.

Oiler port (Fig. 30)

Clean the chain oiler port (36) whenever possible.

36

Fig. 30

Guide bar (Fig. 31)

Before using the machine, clean the groove and oiler

port (37) in the bar with the special gauge oﬀ ered as

an optional accessory.

37

Fig. 31

Side case (Fig. 32)

Always keep the side case and drive area clean of

saw dust and debris. Periodically apply oil or grease

to this area to protect from corrosion as some trees

contain high levels of acid.

16

English

Fig. 32

Fuel ﬁ lter (Fig. 33)

Remove the fuel ﬁ lter from the fuel tank and

thoroughly wash it in solvent. After that, push the

ﬁ lter into the tank completely.

Fig. 33

NOTE

If the ﬁ lter is hard due to dust and dirt, replace it.

Chain oil ﬁ lter (Fig. 34)

Remove the oil ﬁ lter and thoroughly wash it in

solvent.

Fig. 34

Cleaning the cylinder ﬁ ns (Fig. 35)

When wood chips are caught between cylinder ﬁ ns

(38), the engine may overheat, resulting in lower

output. To avoid this, always keep cylinder ﬁ ns and

fan case clean.

Every 100 operating hours, or once a year (more

often if conditions require), clean ﬁ ns and external

surfaces of engine of dust, dirt and oil deposits

which can contribute to improper cooling.

38

Fig. 35

Cleaning the muﬄ er (Fig. 36)

Remove the muﬄ er and spark arrestor, if so

equipped, and clean out any excess carbon from

the exhaust port or muﬄ er inlet every 100 hours of

operation.

Fig. 36

For long-term storage

Drain all fuel from the fuel tank. Start and let engine

run until it stops. Repair any damage which has

resulted from use. Clean the unit with a clean rag, or

the use of high pressure air hose. Put a few drops

of two-cycle engine oil into the cylinder through the

spark plug hole, and spin the engine over several

times to distribute oil.

Cover the unit and store it in a dry area.

CHAIN SHARPENING

Parts of a cutter (Fig. 37, 38)

WARNING

● Gloves should be used when sharpening

chain.

● Be sure to round oﬀ the front edge to reduce

the chance of kickback or tie-strap breakage.

17

English

40

39

41

42

43

44

45

46

47

Fig. 37

51

50

49

48

Fig. 38

39. Top plate

40. Working corner

41. Side plate

42. Gullet

43. Heel

44. Chassis

45. Rivet hole

46. Toe

47. Depth gauge

48. Correct angle on top plate (degree of angle

depends on chain type)

49. Slightly protruding “hook” or point (curve on non-

chisel chain)

50. Top of depth gauge at correct height below top

plate

51. Front of depth gauge rounded oﬀ

LOWERING DEPTH GAUGES WITH A FILE

1) If you sharpen your cutters with a ﬁ le holder,

check and lower the depth.

2) Check depth gauges every third sharpening.

3) Place depth gauge tool on cutter. If depth gauge

projects, ﬁ le it level with the top of the tool.

Always ﬁ le from the inside of the chain toward an

outside cutter. (Fig. 39)

Fig. 39

4) Round oﬀ front corner to maintain original shape

of depth gauge after using depth gauge tool.

Always follow the recommended depth gauge

setting found in the maintenance or operator

manual for your saw. (Fig. 40)

Fig. 40

GENERAL INSTRUCTIONS FOR FILING

CUTTERS

File (52) cutter on one side of the chain from the

inside out. File on forward stroke only. (Fig. 41)

52

5252

Fig. 41

5) Keep all cutters the same length. (Fig. 42)

Fig. 42

6) File enough to remove any damage to cutting

edges (side plate (53) and top plate (54)) of

cutter. (Fig. 43)

18

English

53

54

Fig. 43

SHARPENING ANGLES FOR SHARPENING SAW

CHAIN

1. Part Number 91VG

2. Pitch 3/8″

3. Depth Gauge Setting 0.025″

4. Side Plate Filing Angle 80°

5. Top Plate Angle 30°

6. File Guide Angle 90°

Maintenance schedule

Below you will ﬁ nd some general maintenance

instructions. For further information please contact

HITACHI dealer.

Daily maintenance

○ Clean the exterior of the unit.

○ Clean the chain oil ﬁ lter port.

○ Clean the groove and oil ﬁ lter port in the guide

bar.

○ Clean the side case of saw dust.

○ Check that the saw chain is sharp.

○ Check that the bar nuts are suﬃ ciently tightened.

○ Make sure that the chain transport guard is

undamaged and that it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently

tightened.

Especially inspect the bolt of muﬄ er and ensure

that they are properly tightened before starting

engine. Should any of the bolts be loose,

retighten them immediately. Failure to do so

could result in serious hazard.

○ Check the tip of the bar. Please exchange it for

the new one when it is worn out.

○ Check the band of chain brake. Please exchange

it for the new one when it is worn out.

Weekly maintenance

○ Check the starter, especially cord and return

spring.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode

gap. Adjust it to 0.024″ (0.6 mm) or change the

spark plug.

○ Clean the cooling ﬁ ns on the cylinder and check

that the air intake at the starter is not clogged.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline, and clean fuel

ﬁ lter.

○ Clean chain oil ﬁ lter.

○ Clean the exterior of the carburetor and the space

around it.

○ Clean the fan and the space around it.

○ Clean the muﬄ er of carbon.

NOTE

When ordering the parts to your nearest dealer,

please use the item numbers showing on the

parts breakdown section in this instruction.

MODEL

NO.

OREGON

BAR NO.

LENGTH-

TYPE

CHAIN NO.

CS33EB 26779

26780

160NDEA041

12″ (300 mm)

14″ (350 mm)

16″ (400 mm)

91VG-045X

91VG-052X

91VG-057X

19

English

SIGNIFICATION DES SYMBOLES

REMARQUE : Certains appareils n’en sont pas pourvus.

Symboles

ATTENTION

Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur

signiﬁ cation avant d’utiliser l’outil.

Il est essentiel que vous lisiez et compreniez parfaitement les consignes de

sécurité et autres avertissements suivants et que vous les observiez strictement.

L’utilisation inattentive ou inadéquate de cette machine risque de provoquer des

blessures graves ou fatales.

Lisez, comprenez et suivez toutes les instructions et tous les avertissements

donnés dans ce manuel et sur le produit.

Utilisez toujours des lunettes de protection ainsi qu’une protection pour la tête et

les oreilles lorsque vous utilisez ce produit.

Portez une attention particulière aux phénomènes de rebond. Prenez garde

aux mouvements possibles soudains et accidentels du guide-chaîne de votre

tronçonneuse.

L’utilisation d’une tronçonneuse avec une seule main n’est pas autorisée.

Lorsque vous coupez avec votre machine, tenir celle-ci fermement avec les deux

mains, le pouce enserrant la poignée avant.

Sommaire

Liste des pièces détachées

DESCRIPTION .....................................................21

PRÉCAUTIONS ET CONSIGNES DE

SÉCURITÉ.......................................................22

SPÉCIFICATIONS ................................................25

MONTAGE ...........................................................26

UTILISATION ........................................................27

ENTRETIEN .........................................................34

20

Français

La page charge ...

Hitachi CS33EB16 Manuel utilisateur

Ce manuel convient également à

Hitachi CS33EB16 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents