JVC KD-SH99 Instructions Manual

Marque: JVC

Modèle: KD-SH99

Catégorie: Récepteurs multimédia de voiture

Taper: Instructions Manual

ENGLISH

LVT0654-001A

[J]

ESPAÑOL

FRANÇAIS

CD RECEIVER KD-SH99

RECEPTOR CON CD KD-SH99

RECEPTEUR CD KD-SH99

For customer Use:

Enter below the Model No. and

Serial No. which are located on

the top or bottom of the cabinet.

Retain this information for future

reference.

Model No.

Serial No.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

Detachable

ANGLE

RM-RK100

AUX SEL

VOLUME

R D

AT T

DAB

DISC

PRESET

DISC

COVER.KD-SH99[J]f 4/3/01, 2:55 PM3

ENGLISH

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct

exposure to beam.

3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all

servicing to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches

to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

BEFORE USE

For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car....

If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

How to reset your unit

Press the reset button on the front panel using a

ball-point pen or similar tool.

Note:

Your preset adjustments – such as preset channels or

sound adjustments – will be erased.

CAUTION:

NEVER insert your finger in between the

control panel and the unit, as it may get

caught or hurt. (See page 29.)

EN02-04.KD-SH99[J]f 4/3/01, 2:55 PM2

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit............................... 2

LOCATION OF THE BUTTONS ............ 4

Control panel ........................................... 4

Remote controller .................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ...................... 7

RADIO BASIC OPERATIONS ............. 8

Listening to the radio ................................ 8

Storing stations in memory....................... 9

Tuning into a preset station ...................... 10

CD OPERATIONS .......................... 11

Playing a CD............................................ 11

Locating a track or particular portion

on a CD ................................................. 12

Selecting CD playback modes.................. 12

Playing a CD Text .................................... 13

Prohibiting disc ejection............................ 13

MP3 INTRODUCTION ..................... 14

What is MP3? .......................................... 14

How are MP3 files recorded and

played back? ......................................... 14

MP3 OPERATIONS ........................ 16

Playing an MP3 disc ................................. 16

Locating a file or particular portion

on an MP3 disc ..................................... 17

Selecting MP3 playback modes ............... 20

SOUND ADJUSTMENTS .................. 21

Adjusting the sound ................................. 21

Reinforcing the bass sound ...................... 21

Selecting preset sound modes ................. 22

Storing your own sound adjustments ....... 23

OTHER MAIN FUNCTIONS ............... 24

Setting the clock ...................................... 24

Changing the general settings (PSM) ...... 24

Assigning names to the sources .............. 28

Changing the control panel angle............. 29

Detaching the control panel...................... 30

EXTERNAL COMPONENT OPERATIONS .. 31

Playing external components ................... 31

CD CHANGER OPERATIONS ............. 33

Playing CDs ............................................. 33

Selecting CD playback modes.................. 34

ADDITIONAL INFORMATION ............. 35

TROUBLESHOOTING...................... 36

MAINTENANCE ............................ 38

Handling discs ......................................... 38

SPECIFICATIONS .......................... 39

CAUTION on Volume Setting

CDs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for

example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the

volume before playing a disc and adjust it as required during playback.

About the demonstration mode (DEMO MODE)...

When shipped from the factory, “DEMO MODE” is set to “DEMO ON” in this unit.

The following demonstration, introducing the main features equipped with this unit, will appear on the

display automatically if no sound comes in for 3 minutes. (See page 27.)

•MP3 : (Enables you to play MP3 discs.)

•24bit DAC : (24 bit digital-analog converter: Gives you a high quality sound after D/A

conversion.)

•HS TUNER : (High-sensitivity Tuner: Enables a fine reception of stations.)

•EQUALIZER : (Enables you to fine-adjust the sound to match your preference.)

•SUB WOOFER: (Enables you to connect a subwoofer and to adjust its output level.)

EN02-04.KD-SH99[J]f 4/3/01, 2:55 PM3

ENGLISH

Control panel

4 5

1 0 (eject) button

2 Control dial

3 SEL (select) button

4 EQ (equalization) button

5 S.BASS (S) (super bass) button

6 DISP (D) (display) button

7 BAND (B) button

8 MODE (M) button

9 4/¢ buttons

•

Also function as SSM buttons when pressed

together.

p ATT (angle/attenuator) button

q MP3 INPUT jack

w (control panel release) button

e Remote sensor

r Number buttons

• MO (monaural) button

• LO (local) button

• INT (intro scan) button

• RPT (repeat) button

• RND (random) button

• DVD/Video component operation buttons

t SOURCE (standby/on) button

y Reset button

How to use MODE (M):

If you press MODE (M), this button functions as the Mode button and the unit goes into functions

mode whereby the number buttons and 4/¢ buttons work as different function buttons.

To use these buttons as number buttons and 4/¢ buttons again after pressing MODE (M),

wait for 5 seconds without pressing any number button until the functions mode is cleared.

• Pressing MODE (M) again also clears the functions mode.

During

functions mode

Normally

Equalizing

pattern indicator

Time countdown

indicator

LOCATION OF THE BUTTONS

EN02-04.KD-SH99[J]f 4/3/01, 2:55 PM4

ENGLISH

4 Selects the sound modes.

Each time you press the button, sound modes

change.

5 • Searches for stations while listening to the

radio.

• Fast-forwards or reverses the track/file if

pressed and held while listening to any disc.

• Skips to the beginning of the next track/file or

goes back to the beginning of the current (or

previous) track/file if pressed briefly while

listening to any disc. (See pages 12 and 17.)

6 • Changes the preset channel number while

listening to the radio.

Each time you press the button, the preset

channel number changes, and the selected

station is tuned into.

• Skips to the first file of the next directory or

the first file of the previous directory if

pressed and held while listening to an MP3

disc. (See page 18.)

• Skips to the first file of the next directory or

the first file of the previous directory of the

same hierarchy level if pressed briefly while

listening to an MP3 disc. (See page 19.)

7 • Changes the disc number while listening to

the CD changer.

Each time you press the button, the disc

number changes, and the selected disc

starts playing.

• Skips to the first file of a directory of an upper

hierarchy level or a lower hierarchy level if

pressed briefly while listening to an MP3 disc.

(See page 19.)

8 Skips to the root directory while listening to an

MP3 disc. (See page 19.)

9** Selects the sound adjustment items.

Each time you press the button, the items

change.

p** • Changes the volume.

• Adjusts the sound mode (after SEL is

pressed).

* Without connecting the CD changer, you cannot

select it as the source to play.

** These buttons do not function for the preferred

setting mode adjustment.

Remote controller

ANGLE

RM-RK100

AUX SEL

VOLUME

R D

AT T

DAB

DISC

PRESET

DISC

1 • Turns on the unit if pressed when the unit

is turned off.

• Turns off the unit if pressed and held until

“SEE YOU” appears on the display.

• Drops the volume level if pressed briefly,

and “ATT” flashes on the display.

Press again to resume the volume.

2 • CD : Selects CD player.

• FM : Selects FM tuner.

Each time you press the button, FM

band (FM1, FM2 and FM3) changes.

•

Does not function as the DAB button.

• AM : Selects AM tuner.

• CH : Selects CD changer.*

• AUX : Selects the external components.

Each time you press the button,

“AUX INPUT” and “LINE INPUT” are

alternately selected.

3 Changes the angle of the control panel to

four positions.

EN05-06.KD-SH99[J]f 4/3/01, 2:56 PM5

ENGLISH

Preparing the remote controller

2. Place the battery.

Slide the battery into the holder with the + side

facing upwards so that the battery is fixed in

the holder.

Lithium coin battery

(product number:

CR2025)

3. Return the battery holder.

Insert again the battery holder pushing it until

you hear a clicking sound.

(back side)

WARNING:

• Store the battery in a place where children cannot

reach.

If a child accidentally swallows the battery,

consult a doctor immediately.

• Do not recharge, short, disassemble, heat or

dispose the battery in a fire.

Doing any of these things may cause the battery to

give off heat, crack or start a fire.

• Do not leave the battery with other metallic

materials.

Doing this may cause the battery to give off heat,

crack or start a fire.

• When throwing away or saving the battery, wrap it

in tape and insulate; otherwise, the battery may

start to give off heat, crack or start a fire.

• Do not poke the battery with tweezers or similar

tools.

Doing this may cause the battery to give off heat,

crack or start a fire.

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

• Do not expose the remote sensor to strong

light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness of the

remote controller decreases, replace the battery.

1. Remove the battery holder.

1) Push out the battery holder in the direction

indicated by the arrow using a ball-point

pen or a similar tool.

2) Remove the battery holder.

Remote sensor

(back side)

EN05-06.KD-SH99[J]f 4/3/01, 2:56 PM6

ENGLISH

Turn on the power and select the

source.

When you press the button

for the first time, the power

comes on. Then each time

you press the button, the

source changes as follows:

* If a disc is not in the loading slot, you cannot

select CD as the source to play.

** Without connecting the CD changer, you

cannot select it as the source to play.

To operate the tuner (FM or AM),

see pages 8 – 10.

To play a CD,

see pages 11 – 13.

To play an MP3 disc,

see pages 16 – 20.

To operate external components

(AUX INPUT and LINE INPUT),

see pages 31 – 32.

To operate the CD changer,

see pages 33 – 34.

Adjust the volume.

Note:

After adjusting the volume, you can push in the

control dial to avoid unintended operations.

To use it again, push the control dial again to

make it come out.

Adjust the sound as you want.

(See page 21.)

To drop the volume in a moment

Press and hold /ATT while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press and

hold the button again.

• If you turn the control dial clockwise, you can

also restore the sound.

To turn off the power

Press and hold SOURCE until “SEE YOU”

appears on the display.

To increase the volume.

BASIC OPERATIONS

To decrease the volume.

Note:

When you use this unit for

the first time, set the built-in

clock correctly, see page 24.

Volume level indicator

Volume level appears.

FM TUNER

CD PLAY CD CHANGER

LINE INPUTAUX INPUT

AM TUNER

EN07-07.KD-SH99[J]f 4/3/01, 2:56 PM7

ENGLISH

RADIO BASIC OPERATIONS

Listening to the radio

You can use either automatic searching or

manual searching to tune into a particular station.

Searching a station automatically:

Auto search

Select the band (FM1 – 3, AM).

1 Press SOURCE

repeatedly to select the

tuner as the source.

2 If necessary, press

BAND (B) repeatedly to

select FM or AM.

Each time you press the

button, the band changes

as follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Start searching a station.

When a station is received, searching stops.

Selected band appears.

FM 1 FM 2 FM 3 AM

Press ¢ to search

stations of higher

frequencies.

Press 4 to search

stations of lower

frequencies.

FM 1 FM 2 FM 3 AM

To stop searching before a station is received,

press the same button you have pressed for

searching.

To tune into FM stations only with strong signals

1 Press MODE (M) to enter the functions mode

while listening to an FM broadcast.

2 Press LO (local) while still in the functions

mode, so that the LOCAL indicator lights up on

the display.

This function works only while searching FM

stations, including SSM preset.

Each time you press the button, the LOCAL

indicator lights up and goes off alternately.

Searching a station manually:

Manual search

Select the band (FM1 – 3, AM).

1 Press SOURCE

repeatedly to select the

tuner as the source.

2 If necessary, press

BAND (B) repeatedly to

select FM or AM.

Each time you press the

button, the band

changes as follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

EN08-10.KD-SH99[J]f 4/3/01, 2:56 PM8

ENGLISH

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2 and FM3).

Select the FM band (FM1 – 3) you want

to store FM stations into.

1 Press SOURCE

repeatedly to select the

tuner as the source.

2 If necessary, press

BAND (B) repeatedly to

select the FM band.

Each time you press the

button, the band changes

as follows:

Press and hold both buttons for more

than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2 or FM3).

These stations are preset in the number buttons

— No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned into.

“SSM” appears, then

disappears when automatic

preset is over.

FM 1 FM 2 FM 3 AM

Lights up when receiving

an FM broadcast in stereo.

The MO indicator lights

up.

Press and hold ¢ or 4 until

“M” (manual) starts flashing on the

display.

Tune into a station you want while “M”

is flashing.

• If you release your finger from the button,

the manual mode will automatically turn off

after 5 seconds.

• If you hold down the button, the frequency

keeps changing until you release the

button.

When an FM stereo broadcast is hard to

receive:

1 Press MODE (M) to enter the

functions mode while listening to

an FM stereo broadcast.

2 Press MO (monaural) while still in

the functions mode, so that the

MO indicator lights up on the

display.

• Each time you press the button,

the MO and ST (stereo) indicators

light up alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved (the ST indicator

goes off).

Press ¢ to tune

into stations of higher

frequencies.

Press 4 to tune

into stations of lower

frequencies.

EN08-10.KD-SH99[J]f 4/3/01, 2:56 PM9

ENGLISH

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3 and AM) manually.

Ex.: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

1 Press SOURCE

repeatedly to select the

tuner as the source.

2 If necessary, press

BAND (B) repeatedly to

select FM 1.

Each time you press the

button, the band

changes as follows:

Tune into a station of 88.3 MHz.

Press and hold the number button (in

this example, 1) for more than 2

seconds.

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example, during

battery replacement). If this occurs, preset the stations

again.

Tuning into a preset station

You can easily tune into a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on page 9.

Select the band (FM1 – 3, AM).

1 Press SOURCE

repeatedly to select the

tuner as the source.

2 If necessary, press

BAND (B) repeatedly to

select FM or AM.

Each time you press the

button, the band changes

as follows:

Select the number (1 – 6) for the preset

station you want.

FM 1 FM 2 FM 3 AM

If the sound quality decreases and the

stereo effect is lost while listening to

an FM station...

In some areas, adjacent stations may interfere

with each other. If this interference occurs, this

unit can automatically reduce this interference

noise (the initial setting when shipped from the

factory). However, in this case, the sound

quality will be degraded and the stereo effect

will be also lost.

If you do not want to degrade the sound quality

and to lose the stereo effect, rather than to

eliminate the interference noise, see “To

change the FM tuner selectivity – IF FILTER”

on page 27.

When using this until in an area other than

North or South America:

You need to change the AM/FM channel

intervals. See “To change the AM/FM channel

intervals – AREA” on pages 26 and 27.

Press ¢ to tune

into stations of higher

frequencies.

Press 4 to tune

into stations of lower

frequencies.

“P1” flashes for a while.

FM 1 FM 2 FM 3 AM

EN08-10.KD-SH99[J]f 4/3/01, 2:56 PM10

ENGLISH

CD OPERATIONS

Notes:

• When a disc is in the loading slot, selecting “CD”

as the source by pressing SOURCE starts CD

play.

• When a disc is inserted upside down, the disc

automatically ejects.

• When you play a CD Text, the disc title and

performer appear on the display. Then the current

track title appears on the display, followed by the

track number and elapsed playing time. See also

“Playing a CD Text” (page 13) and “To select the

scroll mode – SCROLL” (page 26).

If a CD Text includes too much text information, some

may not appear on the display.

• If you change the source, CD play also stops (without

ejecting the disc).

To stop play and eject the disc

Press 0.

CD play stops, the control panel moves down, and

the disc automatically ejects from the loading slot.

To return the control panel to its previous

position, press 0 again.

• If you keep the loading slot open for one minute

(or 30 seconds when you have ejected a disc with

the ignition key turned to “OFF”), a beep sounds

and the control panel returns to its previous

position.

Be careful not to get the disc or your finger

caught in between the control panel and the unit.

Note:

If the ejected disc is not removed within 15 seconds, the

disc is automatically inserted again into the loading slot

to protect it from dust. (CD play will not start this time.)

When playing an MP3 disc, refer also to

“MP3 OPERATIONS” on pages 16 to 20.

Playing a CD

Open the loading slot.

The control panel moves down,

and the loading slot appears.

Note:

When an external component is connected to the MP3

INPUT jack, be careful of handling a CD.

Insert a disc into the loading slot.

The unit draws the

disc, the control panel

goes back to its

previous position (see

page 29), and CD play

starts automatically.

• All the tracks on the

disc will be played

repeatedly until you

stop playback—All

Track Repeat Play.

Note:

Do not insert any 8 cm disc into the loading slot as it

will get stuck inside.

The display changes to show the following:

Elapsed playing timeCurrent track

Total track

number of the

inserted disc

Total playing time of

the inserted disc

EN11-13.KD-SH99[J]f 4/3/01, 2:57 PM11

ENGLISH

Locating a track or particular

portion on a CD

To fast-forward or reverse the track

To go to the next track or the previous tracks

Press and hold ¢

while playing a disc, to

fast-forward the track.

Press and hold 4

while playing a disc, to

reverse the track.

Track number

Elapsed playing time

To go to a particular track directly

Press the number button corresponding to the track

number to start its playback.

• To select a track number from 1 – 6:

Press 1 (7) – 6 (12) briefly.

• To select a track number from 7 – 12:

Press and hold 1 (7) – 6 (12) for more than 1

second.

Selecting CD playback modes

To play back tracks at random (Random Play)

1 Press MODE (M) while

playing a disc. The unit enters

the functions mode.

2 Press RND (random) while still

in the functions mode, so that

the RND indicator lights up on

the display.

Then, each time you press

RND, the random play mode

turns on and off alternately.

When the random mode is turned on, the RND

indicator lights up on the display and a track

randomly selected starts playing.

To play back the current track repeatedly

(One Track Repeat Play)

1 Press MODE (M) while

playing a disc. The unit enters

the functions mode.

2 Press RPT (repeat) while still

in the functions mode, so that

the RPT indicator lights up on

the display.

Then, each time you press

RPT, the One Track Repeat

Play mode turns on and off

alternately.

• When One Track Repeat

Play is turned off, All Track

Repeat Play is activated.

Press ¢ briefly while

playing a disc, to go ahead

to the beginning of the next

track. Each time you press

the button consecutively, the

beginning of the next track is

located and played back.

Press 4 briefly while

playing a disc, to go back to

the beginning of the current

track. Each time you press

the button consecutively, the

beginning of the previous

tracks is located and played

back.

EN11-13.KD-SH99[J]f 4/3/01, 2:57 PM12

ENGLISH

To play back only intros (Intro scan)

You can play back the first 15 seconds of each

track sequentially.

1 Press MODE (M) while

playing a disc. The unit enters

the functions mode.

2 Press INT (intro scan) while still

in the functions mode, so that

the “INT” appears on the display.

Then, each time you press INT,

the intro scan play mode turns

on and off alternately.

Playing a CD Text

In a CD Text, some information about the disc (its

disc title, performer and track title) is recorded.

You can show these disc information on the

display.

Select text display mode while

playing a CD Text.

Each time you press the button,

the display changes as follows:

Notes:

• The display shows up to 10 characters at one time

and scrolls if there are more than 10 characters.

See also “To select the scroll mode – SCROLL” on

page 26.

• When you press DISP (D) while playing a

conventional CD, “NO NAME” appears for the disc

title/performer and the track title.

Disc Title / Performer

Track Title

Current track no.

and Elapsed playing time

Track number of the

currently playing track

Prohibiting disc ejection

You can prohibit disc ejection and can lock a disc

in the loading slot.

While pressing SEL (select),

press and hold 0 for more than 2

seconds.

“NO EJECT” flashes on the

display for about 5 seconds, and

the disc is locked and cannot be

ejected.

Note:

If you press 0 while disc ejection is prohibited, the

control panel moves down, but the disc cannot be

ejected.

To return the display panel to its previous position,

press 0.

To cancel the prohibition and unlock the disc,

press and hold 0 for more than 2 seconds again,

while pressing SEL.

“EJECT OK” flashes on the display for about 5

seconds, and the disc is unlocked.

EN11-13.KD-SH99[J]f 4/3/01, 2:57 PM13

ENGLISH

MP3 INTRODUCTION

How are MP3 files recorded

and played back?

MP3 “files (tracks)” can be recorded in

“directories (folders)”—in PC terminology.

During recording, the files and directories can be

arranged in a way similar to arranging files and

directories/folders of computer data.

“Root” is similar to the root of a tree. Every file

and directory can be linked to and be accessed

from the root.

In compliance with ISO 9660, the maximum

allowable depth of nested directories—so-called

“hierarchy”—is eight (inclusive of the root

directory).

Playback order, file search order, and directory

search order of the MP3 files recorded on a disc

are determined by the writing (or encoding)

application; therefore, playback order may be

different from the one you have intended while

recording the directories and the files.

The illustration on the next page shows an

example of how MP3 files are recorded on a

CD-R or CD-RW, how they are played back, and

how they are searched on this unit.

Notes:

• The unit can read a CD-ROM containing MP3

files. However, if non-MP3 files are recorded

together with MP3 files, this unit will take a longer

time to scan the disc. It may also cause the unit to

malfunction.

• The unit cannot read or play an MP3 file without

the extension code—mp3.

• The unit is not compatible with Playlist**.

**A playlist is a simple text file, used on a PC, which enables

users to make their own playback order without physically

rearranging the files.

What is MP3?

MP3 is an abbreviation of Motion Picture Experts

Group (or MPEG) Audio Layer 3. MP3 is simply a

file format with a data compression ratio of 1:10

(128 Kbps*). That means, by using MP3 format,

one CD-R or CD-RW can contain 10 times as

much data volume as a regular CD can.

*Bit rate is the average number of bits that one second of

audio data will consume. The unit used is Kbps (1000 bits/

second). To get a better audio quality, choose a higher bit

rate. The most popular bit rate for encoding is 128 Kbps.

This unit is incorporated with an MP3 decoder.

You can play back MP3 files (tracks) recorded on

CD-Rs, CD-RWs, and CD-ROMs.

Compatible with ID3v1

Extra information data such as album title, performer

name, song title, recording year, music genre and a

brief comment can be stored within an MP3 file.

This unit can show ID3v1 tags (album name,

performer name and song title) on the display.

• Some characters cannot be shown correctly.

• This unit is not compatible with ID3v2.

Other Main Features in this unit:

• Maximum number of hierarchy levels:8

• Maximum number of directories/files: 255

(Total)

• Available characters:A–Z, 0–9, _ (underscore)

• Maximum number of characters for file name

(ISO 9660 Level 1): 12 (inclusive of

separation mark—“.” and

extension code—“mp3”)

(ISO 9660 Level 2): 31 (inclusive of

separation mark—“.” and

extension code—“mp3”)

• Maximum number of characters for directory

name: 31

Precautions when recording MP3 files

on a CD-R or CD-RW

This unit can only read MP3 files that are recorded

in the format that is compliant with ISO 9660 Level 1

or Level 2.

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM14

ENGLISH

MP3 directory/file configuration

MP3 playback/search order (page 17)

• The numbers in circles next to the MP3 files ( ) indicate the playback order and search order of

the MP3 files. Normally this unit plays back MP3 files in the recorded order.

• The numbers inside the directories indicate the playback order and search order of the directories

on an MP3 disc. Normally this unit plays back MP3 files in the directories in the recorded order.

Movement between the directories (page 19)

You can move to another directory on the same hierarchy level (e.g. from Directory 3, you can go to

Directory 5 or 9) or on a different hierarchy level (e.g. from Directory 5, you can go to Directory 4 or 6).

1312

2322 24

1110 2120

1 2

5 6

3 4

ROOT

15 1614

6 7

5 9

Level 1

Level 2

Level 3

Level 4

Level 5

Level 6

Hierarchy

: Root

: Directories

: MP3 files

ROOT

Notes:

• In compliance with ISO 9660, the maximum number of hierarchy

levels is eight, including the root directory.

• When a multi-session disc is loaded, you can only play back the

contents of the last session.

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM15

ENGLISH

Refer also to “CD OPERATIONS” on pages 11 to

13.

Playing an MP3 disc

Open the loading slot.

The control panel moves down,

and the loading slot appears.

Insert an MP3 disc into the loading slot.

The unit draws the

disc, the control panel

goes back to its

previous position (see

page 29), and

playback starts

automatically.

MP3 OPERATIONS

Playback starts automatically from the first file

of the first directory once file check is

completed.

Then, the display changes to show the

following:

• When “TAG ON” is selected (initial

setting: see page 27)

Album name/performer name (directory

name)* = Track title (file name)* =

Elapsed playing time

* If an MP3 file does not have ID3 tags,

directory name and file name appear.

• When “TAG OFF” is selected

Directory name and file name appear.

Notes:

• All the files on the disc will be played repeatedly

until you stop playback—All File Repeat Play.

• MP3 discs require a longer readout time**.

(It differs due to the complexity of the directory/file

configuration.)

**Readout time is the time taken by the unit to scan or

check the disc for files and file information.

Ex.: When the disc contains 13 directories and

125 MP3 files.

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM16

ENGLISH

To change the display information

While playing back an MP3 file, you

can change the file information

shown on the display.

Each time you press DISP (D), the

display changes to show the

following:

• When “TAG ON” is selected (initial

setting: see page 27)

* If an MP3 file does not have ID3 tags,

directory name and file name appear.

• When “TAG OFF” is selected

Note:

• The display shows up to 10 characters at one time

and scrolls if there are more than 10 characters.

See also “To select the scroll mode – SCROLL” on

page 26.

To stop play and eject the disc

Press 0.

Playback stops, the control panel moves down

and the disc automatically ejects from the loading

slot.

To skip to the next file or the previous files

Press ¢ briefly while

playing, to skip ahead to the

beginning of the next file.

Each time you press the

button consecutively, the

beginning of the next file is

located and played back.

(See “MP3 playback/search

order” on page 15.)

Press 4 briefly, while

playing, to skip back to the

beginning of the current file.

Each time you press the

button consecutively, the

beginning of the previous

files is located and played

back. (See “MP3 playback/

search order” on page 15.)

Locating a file or particular

portion on an MP3 disc

To fast-forward or reverse the file

Press and hold 4

while playing an MP3 disc,

to reverse the file.

Press and hold ¢

while playing an MP3 disc,

to fast-forward the file.

Elasped playing time

Track title

(File name)

Album name/

Performer name

(Directory name)

Elasped playing time

File name

Directory name

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM17

ENGLISH

To skip to the next directory—either on

the same hierarchy level or on a different

hierarchy level

On the control panel:

1 Press MODE (M) while

playing an MP3 disc. The unit

enters the functions mode.

2 Press ¢ briefly while

still in the functions mode.

Each time you repeat steps

1 and 2, the next directory is

located (and the first file in

the directory starts playing, if

recorded).

(See “MP3 playback/search

order” on page 15.)

On the remote controller:

Each time you press and hold

the button consecutively, the

next directory is located (and the

first file in the directory starts

playing, if recorded).

(See “MP3 playback/search

order” on page 15.)

To skip to the previous directory—either

on the same hierarchy level or on a

different hierarchy level

On the control panel:

1 Press MODE (M) while

playing an MP3 disc. The unit

enters the functions mode.

2 Press 4 briefly while still

in the functions mode.

Each time you repeat steps

1 and 2, the previous

directory is located (and the

first file in the directory starts

playing, if recorded).

(See “MP3 playback/search

order” on page 15.)

On the remote controller:

Each time you press and hold

the button consecutively, the

previous directory is located

(and the first file in the directory

starts playing, if recorded).

(See “MP3 playback/search

order” on page 15.)

To go to a particular directory directly

IMPORTANT:

To directly select the directories using the

number button(s), it is required that directories

are assigned 2 digit numbers at the beginning of

their directory names. (This can only be done

during the recording of CD-Rs or CD-RWs.)

Ex.: If directory name is “01 ABC”

press 1 to go to directory 01 ABC

If directory name is “1 ABC”

pressing 1 does not work

If directory name is “12 ABC”

press and hold 6 (12) to go to

directory 12 ABC

Press the number button corresponding to the

directory number to start playing the first file in

the selected directory.

• To select a directory number from 01 – 06:

Press 1 (7) – 6 (12) briefly.

• To select a directory number from 07 – 12:

Press and hold 1 (7) – 6 (12) for more than 1

second.

Notes:

• If “MP3” flashes on the display after you have

selected a directory, it means that the directory does

not contain any MP3 files.

• You cannot directly select a directory with a number

greater than 12.

To select a particular file in a directory, press

¢ or 4 after selecting the directory.

PRESET

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM18

ENGLISH

To skip to the next directory on the same

hierarchy level

On the remote controller:

Each time you press the button

consecutively, the next directory

on the same hierarchy level is

located (and the first file in the

directory starts playing, if

recorded).

To skip to the previous directory on the same

hierarchy level

On the remote controller:

Each time you press the button

consecutively, the previous

directory on the same hierarchy

level is located (and the first file

in the directory starts playing, if

recorded).

To skip to the directories on the lower

hierarchy levels

On the remote controller:

Each time you press the button

consecutively, a directory on the

lower hierarchy level is located

(and the first file in the directory

starts playing, if recorded).

To skip to the directories on the upper

hierarchy levels

On the remote controller:

Each time you press the button

consecutively, a directory on the

upper hierarchy level is located

(and the first file in the directory

starts playing, if recorded).

Ex.1: While playing an MP3 file in Directory 1

(see the illustration on page 15)

Ex.2: While playing an MP3 file in Directory 4

(see the illustration on page 15)

1 2 3

4 5 6

4 8 2 4

Ex.1: While playing an MP3 file in Directory 4

(see the illustration on page 15)

Ex.2: While playing an MP3 file in Directory 5

(see the illustration on page 15)

5 9 3 5

Ex.1: While playing an MP3 file in Directory 3

(see the illustration on page 15)

Ex.2: While playing an MP3 file in Directory 5

(see the illustration on page 15)

3 2 1

ROOT

5 4 1

ROOT

4 2 8 4

Ex.1: While playing an MP3 file in Directory 4

(see the illustration on page 15)

Ex.2: While playing an MP3 file in Directory 5

(see the illustration on page 15)

5 3 9 5

PRESET

DISC

PRESET

To go back to the root directly, press R

•

D on

the remote controller. You can go back to the root

from any directory.

• If files are recorded on the first hierarchy level

without putting them into a directory, this unit

starts playing the files.

• If you reach the root, playback will not begin.

Note:

If there is no MP3 file in a directory that you have

skipped to, its directory name appears on the display

with “MP3” flashing. If this happens, the unit pauses

automatically.

EN14-20.KD-SH99[J]f 4/3/01, 2:57 PM19

ENGLISH

To play back only intros (Intro scan)

You can play back the first 15 seconds of each file

sequentially.

1 Press MODE (M) while

playing an MP3 disc. The unit

enters the functions mode.

2 Press INT (intro scan) while still

in the functions mode, so that

“INT” appears on the display.

Then, each time you press INT,

the intro scan play mode turns

on and off alternately.

File number of the

currently playing file

Selecting MP3 playback modes

To play back files at random (Random Play)

1 Press MODE (M) while

playing an MP3 disc. The unit

enters the functions mode.

2 Press RND (random) while

still in the functions mode, so

that the RND indicator lights

up on the display.

Then, each time you press

RND, the random play mode

turns on and off alternately.

When the random mode is turned on, the RND

indicator lights up on the display and a file

randomly selected from all the files on the disc

starts playing.

To play back files repeatedly (Repeat Play)

1 Press MODE (M) while

playing an MP3 disc. The unit

enters the functions mode.

2 Press RPT (repeat) while still

in the functions mode, so that

the RPT indicator lights up on

the display.

Then, each time you press

RPT, the repeat play mode

changes as follows:

RPT 1 RPT 2

Canceled

Ex.: When “RPT 1” is selected.

RPT 1 Lights The current file (or

specified file).

RPT 2 Flashes All files of the current

directory (or specified

directory).

Mode

Plays repeatedly

RPT

Indicator

EN14-20.KD-SH99[J]f 4/3/01, 2:58 PM20

La page charge ...

JVC KD-SH99 Instructions Manual

Marque: JVC

Modèle: KD-SH99

Catégorie: Récepteurs multimédia de voiture

Taper: Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: JVC KD-SH99

Documents connexes

Autres documents

VDO CD 1107 - Manuel utilisateur